Engineering Commons^™

The Effect Of Ozone And Zeolite Concentration To The Performance Of The Treatment Of Wastewater Containing Heavy Metal Using Flotation Process, Eva Fathul Karamah, Setijo Bismo, Hotdi M. Simbolon

Makara Journal of Technology

The Effect of Ozone and Zeolite Concentration to the Performance of the Treatment of Wastewater Containing Heavy Metal Using Flotation Process. Industrial wastewater which contains heavy metal cannot be disposed to the environment directly, due to its toxicity. In this research, separation of metal from wastewater was conducted by sorptive flotation method, using Lampung natural zeolite as bonding agent. The most common diffuser used in the flotation process is air or oxygen. In this research, ozone is used as diffuser because it is a stronger oxidant and more dissolvable in water than oxygen. Besides, ozone is a coagulant aid and …

The Role Of 1 And 9 Wt.% Zn In Precipitation Hardening Of Aa319 Aluminium, Bondan Tiara Sofyan, Sari Susanti, Ridwan R. Yusfranto

Makara Journal of Technology

The Role of 1 and 9 wt.% Zn in Precipitation Hardening of AA319 Aluminium. Aluminium alloys are widely used for automotive application due to its low density and high corrosion resistance. For economic reason, casting of automotive products always uses aluminium scrap as charging materials that may result in fluctuation of content of alloying element, such as Zn. This research studies the role of Zn in precipitation hardening of AA319 aluminium alloys. Hardness and tensile testing were conducted to study the mechanical properties of the alloys, while ageing response was followed by hardness measurements. Evolution of microstructures was observed by …

Electrochemical Durability Of Carbon Nanotubes At 80 °C, Liang Li, Yangchuan Xing

Chemical and Biochemical Engineering Faculty Research & Creative Works

Carbon nanotubes (CNTs) have been studied as an alternative catalyst support in polymer electrolyte membrane (PEM) fuel cells. Recent studies showed that CNTs appear to be more resistant to electrochemical corrosion than carbon black (CB). in a previous study, we have demonstrated the room temperature durability of multiwalled CNTs in both non-catalyzed and catalyzed electrochemical oxidations. This paper is to report results conducted at 80 °C-an operational temperature of PEM fuel cells. It was found that multiwalled CNTs are still more resistant than CB at the elevated temperature. However, the electrochemical oxidation rate is more rapid than that at the …

Demonstration Of A Strategy To Perform Two-Dimensional Diode Laser Tomography, Ryan N. Givens

Theses and Dissertations

Demonstration of a strategy to perform two-dimensional diode laser tomography using a priori knowledge from symmetry arguments and computational fluid dynamic (CFD) calculations is presented for a flat flame burner. The strategy uses an optimization technique to determine flame diameter and location using a vector quantization approach. Next, the variance in a training set, produced from CFD calculations, is captured using principal components analysis. The information in the training set allows interpolation between beam paths resulting in temperature and density maps. Finally, the TDLAS temperature and density maps are shown to agree with traditional thermocouple measurements of the flat flame …

Macro-Mixing In A Draft-Tube Airlift Bioreactor, Hu Ping Luo, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Airlift Reactors Are Pneumatically Agitated Reactors that Have Been Widely Used in Industries, Particularly in Bioprocesses. Extensive Studies About the Flow Dynamics in Airlift Column Reactors Exist; However, Most of These Studies Have Focused on Global Hydrodynamic Parameters using Conventional Techniques. the Local Flow Characteristics, such as the Macro-Mixing and the Turbulence Intensity, Are Crucial for Reliable Design and Scale-Up, and They Remain Unclear. This Work Focuses on Studying the Macro-Mixing in a Draft-Tube Airlift Bioreactor Utilizing an Advanced Flow Dynamic Measurement Technique, Computer Automated Radioactive Particle Tracking (CARPT). True Residence Time Distribution Analyses for the overall Column as Well …

Computational Models Of Tandem Src Homology 2 Domain Interactions And Application To Phosphoinositide 3-Kinase, Dipak Barua, James R. Faeder, Jason M. Haugh

Chemical and Biochemical Engineering Faculty Research & Creative Works

Intracellular signal transduction proteins typically utilize multiple interaction domains for proper targeting, and thus a broad diversity of distinct signaling complexes may be assembled. Considering the coordination of only two such domains, as in tandem Src homology 2 (SH2) domain constructs, gives rise to a kinetic scheme that is not adequately described by simple models used routinely to interpret in vitro binding measurements. To analyze the interactions between tandem SH2 domains and bisphosphorylated peptides, we formulated detailed kinetic models and applied them to the phosphoinositide 3-kinase p85 regulatory subunit/platelet-derived growth factor β-receptor system. Data for this system from different in …

Synthesis Of Adipic Acid From Cyclohexanol By Electrochemical Oxidation Using Cr2O72-/Cr3+ As Indirect Oxidant, Zhen-Hai Liang, Yu-Qing Cui, Hong-Yan Sun

Journal of Electrochemistry

Adipic acid was synthesized by electro-oxidation of cyclohexanol taking Cr₂O₇^2-/Cr³⁺ as indirect oxidant.The best technological conditions were optimized by orthogonal experiment.The optimum condition are as follows: the temperature is 35 ℃,ratio of crude material is n(cyclohexanol)∶n(Cr₂O₇^2-)=0.4∶1 and concentration of H₂SO₄ is 4 mol·L^-1.Under these conditions,the yield of adipic acid can reach 70.29%.Moreover,The effects of concentration of Ag₂SO₄,(NH₄)₂SO₄,H₂SO₄and current density on the formation of Cr₂O₇^2-were also …

Mechanism Of The Cathode Reduction Of Ti(Ⅳ) In Molten Na3Alf6-Alf3, Hai-Bin Sun, Xiu-Rong Zuo, Zhi-Guo Zhong, Xue-Hui Hu

Journal of Electrochemistry

The mechanism of TiO₂ electrode process has been investigated by cyclic voltammetry and chronopotentiometry on the tungsten filament in molten Na₃AlF₆-AlF₃ salts at 990 ℃.The experimental results showed that electrochemical reduction of Ti(Ⅳ) precede were two steps,firstly Ti(Ⅳ) was reduced to Ti(Ⅱ),then Ti(Ⅱ) was reduced to Ti,namely: Ti(Ⅳ)→Ti(Ⅱ)→Ti.

Effects Of Oxidation Methods On The Stability Of Coooh Conductive Network In Foam Nickel Electrodes, Xiao-Feng Li, Yan-Wei Wei, Hui-Chao Dong

Journal of Electrochemistry

Two kinds of the cobalt oxyhydroxide conductive networks in foam nickel electrodes were prepared by different methods i.e.the electrochemical-oxidation(EO) and chemical-oxidation(CO) and which redox behaviors were studied by using cyclic voltammetry and X-ray diffraction measurements.The results show that the CoOOH(CO) has better redox reversibility than CoOOH(EO) and the structure of the former can be kept when nickel electrodes are subjected to a negative potential.Thus,98.7% capacity retention is demonstrated on nickel/metal-hydride batteries with CoOOH(CO) conductive network after being imposed over-discharge state storage;on the contrary,only 83.3% capacity retention is found on the batteries with CoOOH(EO) conductive network.

The Influence Of The Sputtering Power On The Structural And Electrochemical Properties Of Tin Oxide Films, Min-Zhen Cai, Jie Song, Ming-Sen Zheng, Qi-Hui Wu, Sun-Tao Wu, Quan-Feng Dong

Journal of Electrochemistry

Tin oxide films were deposited on silicon substrates at room temperature using the radio frequency(RF) magnetron sputtering with different sputtering power.The influence of sputtering power upon the crystal structure,surface morphology and electrochemical properties of tin oxide films were then investigated.The XRD and SEM results illustrate that the phase of tin oxide thin films changed from amorphous to crystalline and the grain size augments with the increase of the sputtering power.The constant current charge and discharge cycle tests imply that the initial irreversible capacity loss of Li/tin oxide batteries increase and which capacity decrease as the sputtering power increases.The sputtering power …

Effect Of Au At Different States On Electrocatalytic Performance Of Pd Catalyst For Oxidation Of Formic Acid, Xin Wang, Ya-Wen Tang, Tian-Hong Lu

Journal of Electrochemistry

Using liquid-reduction or complex-redution method,four catalysts,i.e,the Au/C,Pd/C,Pd-Au/C-T and Pd-Au/C-H were preparated and which electroanalytic activities and stabilities for the oxidation of formic acid were compares.It was found that the Au/C catalyst has no electrocatalytic activity,and the Pd/C catalyst possesses the good electrocatalytic performance for the oxidation of formic acid.The addition of Au into the Pd/C catalyst can increase the electrocatalytic activity and stability.Especially,the electrocatalytic activity and stability of the Pd-Au/C-T catalyst with the alloy of Pd and Au are better than that of the of the Pd-Au/C-H catalyst,in which,Pd and Au do not form the alloy.The investigation of its reason …

Synthesis Of 2,2′-Dichlorohydrazobenzene Using An Ion Exchange Membrane, Chao Zhang, Pei-Jin Li

Journal of Electrochemistry

Using an ion exchange membrane as a separator,the 2,2′-Dichlorohydrazobenzene is synthesized by the electrolytic reduction of o-chloronetrobenzene.The effects of electrode activation condition,current density,electrolyte temperature on electrolytic reduction are discussed.It was found that the optimum reaction temperature is 80 ℃.When the electrolyte concentration was 30% NaOH at the anode and 10% NaOH at the cathode,current density is 4.2A/dm²,the current efficiency reached 73% and yield is 83%.

The Role Of Sr²⁺ On The Structure And Reactivity Of Sro-Cao-Zno-Sio2 Ionomer Glasses, Daniel Boyd, Mark R. Towler, Sally Watts, Robert G. Hill, Anthony W. Wren, Owen M. Clarkin

Chemical and Biochemical Engineering Faculty Research & Creative Works

The suitability of Glass Polyalkenoate Cements (GPCs) for use in orthopaedics is retarded by the presence in the glass phase of aluminum, a neurotoxin. Unfortunately, the aluminum ion plays an integral role in the setting process of GPCs and its absence is likely to hinder cement formation. However, the authors have previously shown that aluminum free GPCs may be formulated based on calcium zinc silicate glasses and these novel materials exhibit significant potential as hard tissue biomaterials. To further improve their potential and given that Strontium (Sr) based drugs have had success in the treatment of osteoporosis, the authors have …

Bubble Velocity, Size, And Interfacial Area Measurements In A Bubble Column By Four-Point Optical Probe, Junli Xue, Muthanna H. Al-Dahhan, M. P. Dudukovic, R. F. Mudde

Chemical and Biochemical Engineering Faculty Research & Creative Works

The Four-Point Optical Probe is Applied in a Bubble Column with an Air-Water System to Investigate the Bubble Properties (Local Gas Holdup, Velocity, Chord Length, Specific Interfacial Area, and Frequency) over a Range of Gas Superficial Velocities. Both Bubbles Moving Upward and Downward Are Recorded and Measured as Opposed to Only Upward Bubbles Measured and Reported in Other Studies Involving Probes. the Probe Worked Efficiently in Both Bubbly Flow and Highly Churn-Turbulent Flow at Very High Superficial Gas Velocities. Bubble Properties at the Conditions of Churn-Turbulent Flow Are Obtained and Investigated for the First Time. the Changes in the Bubble …

Thermal Damage Approach Of Concrete: Application To Specimens Subjected To Combined Compressive And High Temperature Loads, Abdellah Menou, Ghassan Mounajed, Hocine Boussa, Christian La Borderie, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

Within the framework of study of concrete structures subjected to fire, .a theoretical and experimental work was conducted. The aim of this study was to investigate and to model the damage mechanisms of concrete after their exposure to high temperatures. The multiphase Digital Concrete Model as well as the damage model, MOD EV, which were both implemented on the finiteelem~ rit software package, SYMPHONIE, were used simμltaneously to assess the thermal damage of the concrete. In order to validate the thermal damage model, an experimental investigation was performed. The mechanical characteristics of 5 cementitious materials, which included cement paste, mortar, …

Modeling Of Trickle-Bed Reactors With Exothermic Reactions Using Cell Network Approach, Jing Guo, Yi Jiang, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

One-Dimensional (1D) and Two-Dimensional (2D) Cell Network Models Were Developed to Simulate the Steady-State Behavior of Trickle-Bed Reactors Employed for the Highly Exothermic Hydrotreating of Benzene. the Multiphase Mass Transfer-Reaction Model and Novel Solution Method Are Discussed in This Report. the 1D Model Was Shown to Satisfactorily Simulate the Axial Temperature Field Observed Experimentally for Multiphase Flow with Exothermic Reactions. the 2D Reactor Modeling Provided Valuable Information About Local Hot Spot Behavior within the Multiphase Reactor, Identifying Situations in Which Hot Spots May Form. the Model Took into Consideration the Heterogeneous Nature of Liquid Distribution, Including Radial Liquid Maldistribution and …

Tem Analysis Of Apatite Surface Layers Observed On Zinc Based Glass Polyalkenoate Cements, D. Boyd, Mark R. Towler, A. W. Wren, O. M. Clarkin, D. A. Tanner

Chemical and Biochemical Engineering Faculty Research & Creative Works

The amorphous nature and composition of the surface apatite layers observed on glass polyalkenoate cements based on zinc silicate glasses (Zn-GPCs) after immersion in simulated body fluid (SBF) have been analyzed by the transmission electron microscopy (TEM). TEM was conducted using a JEOL JEM-2011 electron microscope operated at an accelerating voltage of 200 kV. The composition elements of the surface layer indicated the presence of calcium, phosphorous, zinc, and strontium within the amorphous structure. This composition, in particular the inclusion of Zn in the structure, indicates the lack of crystallinity associated with the formation of the apatite layers observed on …

Digestion Of Sand-Laden Manure Slurry In An Upflow Anaerobic Solids Removal (Uasr) Digester, Khursheed Karim, Rebecca Hoffmann, M. (Muthanna) H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Studies on the Performance of a Laboratory Scale Up flow Anaerobic Solids Removal (UASR) Digester Were Carried Out using Sand-Laden Cow Manure Slurries Having Total Solids (TS) Concentration as 50 and 100 G/l. Hydraulic Retention Time (HRT) Was Maintained as 32.4 Days, Which Resulted in the Volatile Solids (VS) Loading Rates of 1 and 1.64 G/l D. the UASR System Was Designed to Remove Sand from the Manure Slurry, While Anaerobically Digesting Biodegradable Solids Inside a Single Reactor. to Enhance the Contact of Microorganisms and Substrate, the Liquor from the Top of the Digester Was Recirculated through the Bed of …

Mpsa Effects On Copper Electrodeposition Investigated By Molecular Dynamics Simulations, John N. Harb, Richard L. Rowley, Dean R. Wheeler, Clint G. Guymon

Faculty Publications

In superconformal filling of copper-chip interconnects, organic additives are used to fill high-aspect-ratio trenches or vias from the bottom up. In this study we report on the development of intermolecular potentials and use molecular dynamics simulation.

Magnetically Assisted Impaction Mixing Of Nanosize Particles, James V. Scicolone

Theses

Magnetically assisted impaction mixing (MAIM) is a novel dry mixing technique, which can be used to mix nanoparticles. Mixing of nanoparticles is usually conducted in solvent-based mixing techniques. The solvents used in these techniques are usually organic, which can be expensive and harmful to the environment. MAIM creates homogeneous nanoparticle mixtures while eliminating conditioning and drying steps associated with wet mixing techniques. To create the best mixing quality of nanoparticles, MAIM was optimized by studying the effects of magnet-to-sample ratio, time, magnet size, and constituents of the mixture. The results were then compared with other well-known mixing techniques.

To characterize …

Mixing Of Nanoparticles In A Stirred Tank In High Pressure Carbon Dioxide, Nitin Aggarwal

Theses

Mixing of nanoparticles of different compositions offers wide opportunities in manufacturing new nanocomposite materials with unique electronic, optical, mechanical, and chemical properties. However, due to large cohesive forces between nanoparticles, they often form large micron-sized agglomerates, thus losing their main advantage of small size and high surface area. Therefore, breaking of these agglomerates is necessary prior to mixing. One of the techniques to achieve deagglomeration and mixing of nanoparticles is based on rapid depressurization/expansion of supercritical suspensions. where the suspension of initially premixed agglomerates in supercritical CO₂ pass through the nozzle undergoing deagglomeration as a result of rapid expansion …

Ultra-Fine Particle Formation Using Principle Of Rapid Expansion Of Supercritical Solutions`, Miraj Minesh Sheth

Theses

There are indications in the chemical and pharmaceutical industries that the reduction in size of a crystalline particle can lead to better performance of the drug compound, particularly for water insoluble drugs, in the final dosage form. Many particle formation techniques have been investigated in recent years by researchers to obtain desired particulate sizes and size distributions. Supercritical fluid technologies have been successfully investigated for particle formation due to its unique gas/liquid properties in the supereritical state. In this report, results of particle formation using the principles of Rapid Expansion of Supercritical Solutions (RESS) have been documented.

In the RESS …

A Method For Determining Stokes Flow Around Particles Near A Wall Or In A Thin Film Bounded By A Wall And A Gas-Liquid Interface, Ashok S. Sangani, Shailesh S. Ozarkar

Biomedical and Chemical Engineering - All Scholarship

A method for determining Stokes flow around particles near a wall or in a thin film bounded by a wall on one side and a nondeformable gas-liquid interface on the other side is developed. The no-slip boundary conditions at the wall are satisfied by constructing an image system based on Lamb’s multipoles. Earlier results for the image systems for the flow due to a point force or a force dipole are extended to image systems for force or source multipoles of arbitrary orders. For the case of a film, the image system consists of an infinite series of multipoles on …

A Kinetic Theory For Particulate Systems With Bimodal And Anisotropic Velocity Fluctuations, Ashok S. Sangani, Shailesh S. Ozarkar, Volodymyr I. Kushch, Donald L. Koch

Biomedical and Chemical Engineering - All Scholarship

Observations of bubbles rising near a wall under conditions of large Reynolds and small Weber numbers have indicated that the velocity component of the bubbles parallel to the wall is significantly reduced upon collision with a wall. To understand the effect of such bubble-wall collisions on the flow of bubbly liquids bounded by walls, a model is developed and examined in detail by numerical simulations and theory. The model is a system of bubbles in which the velocity of the bubbles parallel to the wall is significantly reduced upon collision with the channel wall while the bubbles in the bulk …

Morphologies And Kinetics Of A Dewetting Ultrathin Solid Film, Mikhail Khenner

Mathematics Faculty Publications

The surface evolution model based on geometric partial differential equation is used to numerically study the kinetics of dewetting and dynamic morphologies for the localized pinhole defect in the surface of the ultrathin solid film with the strongly anisotropic surface energy. Depending on parameters such as the initial depth and width of the pinole, the strength of the attractive substrate potential and the strength of the surface energy anisotropy, the pinhole may either extend to the substrate and thus rupture the film, or evolve to the quasiequilibrium shape while the rest of the film surface undergoes phase separation into a …

Enhanced Stability Of A Dewetting Thin Liquid Film In A Single-Frequency Vibration Field, Mikhail Khenner

Mathematics Faculty Publications

Dynamics of a thin dewetting liquid film on a vertically oscillating substrate is considered. We assume moderate vibration frequency and large (compared to the mean film thickness) vibration amplitude. Using the lubrication approximation and the averaging method, we formulate the coupled sets of equations governing the pulsatile and the averaged fluid flows in the film, and then derive the nonlinear amplitude equation for the averaged film thickness. We show that there exists a window in the frequency-amplitude domain where the parametric and shear-flow instabilities of the pulsatile flow do not emerge. As a consequence, in this window the averaged description …

Enhanced Stability Of A Dewetting Thin Liquid Film In A Single-Frequency Vibration Field, Sergey Shklyaev, Mikhail Khenner, Alexei Alabuzhev

Mathematics Faculty Publications

Dynamics of a thin dewetting liquid film on a vertically oscillating substrate is considered. We assume moderate vibration frequency and large (compared to the mean film thickness) vibration amplitude. Using the lubrication approximation and the averaging method, we formulate the coupled sets of equations governing the pulsatile and the averaged fluid flows in the film, and then derive the nonlinear amplitude equation for the averaged film thickness. We show that there exists a window in the frequency-amplitude domain where the parametric and shear-flow instabilities of the pulsatile flow do not emerge. As a consequence, in this window the averaged description …

Enhanced Stability Of A Dewetting Thin Liquid Film In A Single-Frequency Vibration Field, Sergey Shklyaev, Mikhail Khenner, Alexei Alabuzhev

Mathematics Faculty Publications

Dynamics of a thin dewetting liquid film on a vertically oscillating substrate is considered. We assume moderate vibration frequency and large (compared to the mean film thickness) vibration amplitude. Using the lubrication approximation and the averaging method, we formulate the coupled sets of equations governing the pulsatile and the averaged fluid flows in the film, and then derive the nonlinear amplitude equation for the averaged film thickness. We show that there exists a window in the frequency-amplitude domain where the parametric and shear-flow instabilities of the pulsatile flow do not emerge. As a consequence, in this window the averaged description …

Morphologies And Kinetics Of A Dewetting Ultrathin Solid Film, Mikhail Khenner

Mathematics Faculty Publications

The surface evolution model based on geometric partial differential equation is used to numerically study the kinetics of dewetting and dynamic morphologies for the localized pinhole defect in the surface of the ultrathin solid film with the strongly anisotropic surface energy. Depending on parameters such as the initial depth and width of the pinole, the strength of the attractive substrate potential and the strength of the surface energy anisotropy, the pinhole may either extend to the substrate and thus rupture the film, or evolve to the quasiequilibrium shape while the rest of the film surface undergoes phase separation into a …

Simulation Of A Circulating Fluidised Bed Biomass Gasifier Using Aspen Plus: A Performance Analysis, Wayne Doherty, Anthony Reynolds, David Kennedy

Conference Papers

In the near future biomass gasification is likely to play an important role in energy production and conversion. Its application has great potential in the context of climate change mitigation, increasing efficiency and energy security. Atmospheric circulating fluidised bed (CFB) technology was selected for the current study. An original computer simulation model of a CFB biomass gasifier was developed using ASPEN Plus (Advanced System for Process ENgineering Plus). It is based on Gibbs free energy minimisation and the restricted equilibrium method was used to calibrate it against experimental data. This was achieved by specifying the temperature approach for the gasification …