Engineering Commons^™

Layered Structure Protonic Ceramic Conductors Of The Form Ba5in2+Xal2zr1-Xo13-Δ, Nathan Cretegny

All Theses

In this work, the hexagonal perovskite of targeted composition Ba₅In_2+xAl₂Zr_1-xO₁₃ (x=0, 0.1, 0.2) was synthesized via a solid-state synthesis route to study the impact of oxygen vacancy concentration in layered hexagonal perovskites. Precursor oxides were mixed in stoichiometric proportions, calcined between 800-1200℃ and sintered at 1475℃. The sintered pellets were crushed into fine powders to investigate the chemistry and structure through X-ray diffraction, neutron diffraction, inductively coupled plasma mass spectrometry, and nuclear magnetic resonance. Dense pellets were used to study conductivity properties using electrochemical impedance spectroscopy.

The synthesis approach produced 100% …

Passive Wireless Corrosion And Temperature Detection In High-Temperature Environments, Noah Lane Strader

Graduate Theses, Dissertations, and Problem Reports

This work focuses on the theory and development of LC sensors for high temperature and corrosion measurement for stainless steel and copper surfaces with power industry and general corrosion detection applications. The LC resonators were fabricated via screen printing an Ag inductor on an alumina substrate. The LC design was modeled using the ANSYS HFSS modeling package. The LC passive wireless sensors operate with resonant frequencies centered at 85-110 MHz. The wireless response of the LC sensor was interrogated and received by a radio frequency signal generator and spectrum analyzer at temperatures from 50-800 °C for copper ground planes and …

Characterizing The Structure And Radiation Resistance Of Weberite-Type Complex Oxides, Igor M. Gussev

Doctoral Dissertations

Weberite-type A₃BO₇ oxides, where A is a trivalent rare earth and B is a pentavalent element like Ta, have been a focus of research due to the discovery of the weberite-type local atomic arrangement in ceramics with a defect-fluorite structure. Earlier studies primarily examined their long-range structures, leaving gaps in understanding their short-range atomic behavior. This thesis investigates various weberite-type tantalates across all structural scales. There has been debate over the long-range structure of Y₃TaO₇, a medium-sized rare earth tantalate oxide, particularly regarding its spacegroup symmetry. This work identifies Y₃TaO_{7 …}

Fabrication Of Alumina Membranes From Uv Resin– Alumina Particle Slurries, Dominique Henry Porcincula

Master's Theses

Ceramics membranes are made in a wide variety of different techniques using a wide variety of different materials. However, many of the common techniques utilize a slurry of ceramic particles, additives, and either organic solvent or water that is shaped into a membrane, left to dry, and then sintered together. Drying is a time consuming process, often requiring several hours for the liquid medium to evaporate. Defect formation caused by development of partial pressures across the drying membrane, including cracks and warpage, also typically occurs during the drying process. To address this, slurries of ceramic particles made with a low …

Preparation Of High Entropy Titanite Pyrochlore And Radiation Stability Study, Adam Gootgeld

All Theses

Pyrochlore has been studied as a host phase for safe storage of radionuclides and exists naturally with long-term stability with good long-range order [1]. High entropy oxides show promising tunable properties that could demonstrate favorable bulk deposit of radioactive materials such as spent nuclear fuel (Uranium and other actinides). It is proposed that using high entropy oxides (HEOs) as the cation in this framework will shift the gibbs free energy so that radioactive nuclear waste will be stabilized for safe, long-term, eco-friendly storage. We have established a consistent method to fabricate high entropy titanite pyrochlores. In this study, ion beam …

Efficient Sintering Of Lunar Soil Using Concentrated Sunlight, Diprajit Biswas

Electronic Theses and Dissertations

Construction material is one crucial need for long-term habitation on the moon. When concentrated for high heat flux, solar radiation can heat lunar soil or regolith until it sinters at temperatures above 900°C. The solid, sintered soil simulant can be used as construction material. This work explores the conditions leading to effective lunar soil sintering for both direct and indirect irradiated sintering. Lunar soil simulants were sintered using concentrated light from a xenon-arc lamp with varying heat flux intensity. During direct sintering of LHS-1, a sintering range of 860°C-1140°C corresponding to a peak heat flux of 105-120 kW/m2 was identified …

Influence Of Platinum Nanoparticles On Ionic Transport And Hydrogen Reactivity Of Yttria-Stabilized Zirconia Thin Films, Firas Mahyob

Electronic Theses and Dissertations

Yttria-stabilized zirconia (YSZ) is a widely used ceramic material in solid oxide fuel cells, oxygen sensors, and sensing applications due to its high ionic conductivity, chemical inertness, and thermal stability. YSZ is promising active coating for use in miniaturized harsh environment wireless surface acoustic sensors to monitor gases such as H₂. Adding catalytic Pt nanoparticles can enhance gas reactivity and lead to associated film conductivity changes.

In this work, thin films with an (8% Y₂O₃ - 92% ZrO₂) composition were deposited onto piezoelectric langasite substrates using RF magnetron sputtering in Ar:O₂ - …

Atomistic Simulation Studies Of Thin Film Growth And Plastic Deformation In Metals And Metal/Ceramic Nanostructures, Reza Namakian

LSU Doctoral Dissertations

Despite the significant improvements in manufacturing and synthesis processes of metals and ceramics in the past decades, there are still areas in which the procedure is still frequently more of an art or skill rather than a science. Therefore, systematic and combined experimental and computational studies are required to facilitate the development of techniques that offer thorough understanding of the events taking place during manufacturing and synthesis processes. With regard to these issues, it is paramount to address microscale characterizations and atomic scale understanding of the events during fabrication processes. One of the focuses of this study is unraveling fundamental …

Modified Reactive Sputter Deposition Of Titanium Nitride Thin Films Via Hipims With Kick-Pulse And Improvement Of The Structure-Zone Model, Andrew Miceli

UNF Graduate Theses and Dissertations

Direct current (DC) and radio frequency (RF) sputtering methods have been commonplace in industry for several decades and widely studied in literature. Hard films of nitrides, such as titanium nitride (TiN), have been deposited using reactive DC sputtering onto cutting tools and medical devices extensively as well. For these applications, the films require excellent adhesion, high density, and high hardness. High-Power Impulse Magnetron Sputtering (HIPIMS) has emerged over the last several years as a method to produce films with increased density and mechanical properties. Process-structure-property relationships for reactive HIPIMS are not yet well developed. Additionally, conventional HIPIMS suffers from relatively …

Intragranular Tungsten-Titanium Carbide Composite Ceramics Via Gas-Solid Displacement Reactions, Ryan Daniel Dempsey

Doctoral Dissertations

"Research presented herein details the synthesis and characterization of nanocomposite ceramics featuring novel heterogeneous microstructures of potential interest in a variety of electrical and structural applications. Specifically, W-TiCy composite ceramics featuring tungsten nanoprecipitates located primarily within TiCy grains have been produced via sintering of intragranular nanocomposite powders produced via reaction processing-based techniques. This dissertation details the thermodynamic basis and applied kinetics of a processing scheme for fabricating nanocomposite ceramics whose morphological heterogeneity reflects that originally developed in the powder state. The first study in this series overviews the motivation for applying metallothermic displacement reactions, conducted through gaseous intermediates, to solid …

Development Of High Kinetic Inductance Superconducting Nanowire Devices On High Permittivity Strontium Titanate Substrates, Jamie Timmons

UNF Graduate Theses and Dissertations

This thesis involves the fabrication and characterization of devices made from two different superconducting materials: yttrium barium copper oxide (YBCO), a high-TC complex oxide, and niobium nitride (NbN), a low-TC transition metal nitride. Both types of devices are fabricated on strontium titanate substrates, which provides a good lattice match to YBCO and also an extremely large permittivity at low temperature. We demonstrate that wet etching of YBCO thin films via bromine can be a viable microfrabriation technique for the material. Using approximately 35 nm thick epitaxially grown YBCO on an STO substrate, we were able to fabricate YBCO “microwires” with …

Advanced Microstructural Characterization Of Functionally Graded Dental Ceramic Material For Materials-Informed Finishing, Angani Vigneswaran

Theses and Dissertations--Manufacturing Systems Engineering

Yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) has gained popularity as the choice of material for dental prosthetics. Ivoclar Vivadent’s IPS e.max ZirCAD Prime dental ceramic incorporates a unique gradient technology that varies the yttria content over the thickness of the material. The top layer is composed of 5Y-TZP which is desired for its optical properties while the bottom layer is composed of a much stronger 3Y-TZP. In between the two layers, 5Y-TZP and 3Y-TZP are mixed to form a transition layer. Varying the amount of yttria allows for more esthetically pleasing translucency in the visible areas of the restoration without compromising …

Xps Study Of Calcium Lanthanum Sulfide Ceramics, Brian E. Butkus

Graduate Thesis and Dissertation 2023-2024

Long wave infrared (LWIR) optics that transmit in the 8 to 14 m wavelength range and, additionally, can withstand severe physical and thermal stresses are needed for advanced remote sensing, guidance and communication-based applications. However, most non-oxide transparent LWIR optics do not have the wider transmission range, nor the hardness and resistance to thermal shock needed for extreme environments. Because of these limitations, research is circling back to a promising material, calcium lanthanum sulfide (CLS), that could meet LWIR needs for extreme environments.

In this thesis, we will demonstrate the abilities of x-ray photoelectron spectroscopy (XPS) as a technique for …

Development Of Interatomic Potential Of High Entropy Diborides With Artificial Intelligence Approach To Simulate The Thermo-Mechanical Properties, Nur Aziz Octoviawan

MSU Graduate Theses

The interatomic potentials designed for binary/high entropy diborides and ultra-high temperature composites (UHTC) have been developed through the implementation of deep neural network (DNN) algorithms. These algorithms employed two different approaches and corresponding codes; 1) strictly local & invariant scalar-based descriptors as implemented in the DEEPMD code and 2) equivariant tensor-based descriptors as included in the ALLEGRO code. The samples for training and validation sets of the forces, energy, and virial data were obtained from the ab-initio molecular dynamics (AIMD) simulations and Density Functional Theory (DFT) calculations, including the simulation data from the ultra-high temperature region (> 2000K). The study …

System Analysis Of An Internal Combustion Engine (Ice) – Solid Oxide Fuel Cell (Sofc) Hybrid Cycle, Jose Javier Colon Rodriguez

Graduate Theses, Dissertations, and Problem Reports

Due to the intermittent nature of renewable energy and the rigid operation of existing coal plants, the need for flexible power generation technology is eminent. Hybrid energy systems have shown potential for flexible, grid following dynamics while maintaining higher efficiencies. The work below focuses on the performance analysis of a proposed 100 kW pressurized Internal Combustion Engine (ICE) and Solid Oxide Fuel Cell (SOFC) hybrid system. The un-utilized fuel from the SOFC stack provided the chemical energy to operate the engine. A turbocharger was used to deliver the necessary air flow for both the stack and engine. An external reformer …

Effects Of Confinement On Ionic Liquids And Deep Eutectic Solvents For The Design Of Catalytic Systems, Electrochemical Devices, And Separations, Andrew Drake

Theses and Dissertations--Chemical and Materials Engineering

Confinement of ionic liquids (ILs) and deep eutectic solvents (DESs) within mesoporous materials such as silica helps to control the local environment within the pores for applications such as catalysis, electrochemistry, and absorption. Silica thin films with 2.5 and 8 nm pores and micron-sized silica particles with pore diameters of 5.4 and 9 nm were synthesized to study the effect of nanoconfinement on ILs 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF₆]), 1-butyl-3-methylimidazolium chloride ([BMIM][Cl]), and DESs reline and ethaline (choline chloride and urea or ethylene glycol). Silica thin films with vertically aligned, well ordered, and accessible pores were synthesized via the evaporation-induced …

Fabrication, Thermophysical, And Mechanical Properties Of Cermet And Cercer Fuel Composites For Nuclear Thermal Propulsion, Neal D. Gaffin

Doctoral Dissertations

Nuclear thermal propulsion (NTP) utilizes nuclear fission to double the efficiency of
in-space propulsion systems compared with traditional combustion rocket systems.
NTP systems are limited primarily by the fuel material choice, due to the extreme
conditions they will need to endure, including temperatures up to 3000 K, multiple
thermal cycles with rapid heating and cooling, exposure to hot flowing hydrogen,
large thermal gradients, and high neutron flux. Particle based fuels, namely ceramic-
metallic (cermet) and ceramic-ceramic (cercer) composites are both promising fuel
element material candidates for NTP. Given the high temperature nature, these
materials are difficult to fabricate and very …

Assembly Of Ceramic Particles In Aqueous Suspensions Induced By High-Frequency Ac Electric Field, James E. John Iv

Mechanical & Aerospace Engineering Theses & Dissertations

Ceramic materials processed using colloidal methods have been the focus of a great deal of research aimed at tailoring the final structure and microstructure of the finished ceramic sample. To this end, various external field effects have been investigated to modify the suspension microstructure without manipulating the ceramic particles directly. In a previous work in the field of ice templating it has been shown that AC electric fields are able to produce microstructural changes in ice templated ceramics that have significantly improved the final mechanical properties. However, the mechanisms for this process are still not well understood in ceramics.

To …

Material Characterization And Comparison Of Sol-Gel Deposited And Rf Magnetron Deposited Lead Zirconate Titanate Thin Films, Katherine Lynne Miles

Mechanical Engineering ETDs

Lead zirconate titanate (PZT) has been a material of interest for sensor, actuator, and transducer applications in microelectromechanical systems (MEMS). This is due to their favorable piezoelectric, pyroelectric and ferroelectric properties. While various methods are available to deposit PZT thin films, radio frequency (RF) magnetron sputtering was selected to provide high quality PZT films with the added capability of batch processing. These sputter deposited PZT films were characterized to determine their internal film stress, Young’s modulus, composition, and structure. After characterization, the sputtered PZT samples were poled using corona poling and direct poling methods. As a means of comparison, commercially …

An Experimental Study Of Norton And Thule Cooking Pot Performance, Caelie Marshall Butler

Dissertations and Theses

Ceramic technology was adopted by hunter-gatherers of the Paleo-Inuit Norton tradition in the Western Arctic between 2800 and 2500 years B.P., corresponding with an increase in the use of aquatic resources. Pottery production and use continued until approximately 1,500 BP, and resumed during the Neo-Inuit Birnirk and Thule periods, approximately 1,350 years BP. The technical characteristics of Norton and Thule ceramics suggest they performed differently when used for cooking, with Norton ceramics best suited for cooking using direct or suspended heat, and Thule ceramics best suited for indirect heat. Prior experimental archaeological research has focused on Thule ceramics, with limited …

Developing Positive Thermal Coefficient (Ptc) Heaters For Solar Electric Cooking, Katarina Ivana Brekalo, Andrew Shepherd

Physics

Positive Thermal Coefficients, PTCs, are materials that abruptly change in resistance in response to changes in temperature. The purpose of this experiment is to explore the viability of using the switching type ceramic PTC thermistor as a replacement for current resistive heaters. These types of PTCs have a nonlinear change in resistance with increases in temperature. This device will be used as a temperature-controlling heating element intended to power an Insulated Solar Electric Cooker (ISEC). The ISEC is designed to cook meals throughout the day for impacted communities as an alternative cooking method that doesn’t require biofuel as an energy …

Enabling Nanoimprint Lithography Techniques Across Multiple Manufacturing Processes, Vincent Einck

Doctoral Dissertations

Advanced nanooptics in the areas of flat lenses, diffractive elements, and tunable emissivity require a route to high throughput manufacturing. Nanooptics are often demanding of high refractive index materials, nanometer precision and ease of fabrication. Nanoimprint lithography (NIL) is a low-cost, high throughput manufacturing technique beginning to be realized in commercial industry.^1,2 The NIL process is an ideal manufacturing candidate due to its ability to have a fast process time, efficient use of materials, repeatability and high precision while also having wide diversity of potential structures and material choices. Appling NIL techniques to other facets of manufacturing enable the …

Modeling Hierarchical Porous Electrodes With Tailored Anisotropic Structure, Debanjan Sarker

All Theses

Modern electric vehicles and consumer electronics applications demand high specific energy from Li-ion batteries, which can be charged and discharged faster. In the search for high specific energy, researchers have tried to make thicker battery electrodes which contain a greater proportion of active material. While chemical and structural modification of electrodes can help to increase the electronic conductivity of active material, the microstructure of porous electrodes can be engineered to enhance ion transport for fast charge and discharge. Previous research has shown that macropores introduced by directional freeze tape casting can enhance the performance of thick porous electrodes. For instance, …

Evaluating The Effects Of Granulated Rubber And Glass Fibers In Polymer Concrete As A Structural Material For Wafer Grinding Machines, Kevin Gabriel Kuehn, Philip Randall Streeter

Materials Engineering

Polymer concrete is a composite material used to replace cast iron and steel in wafer grinding machines for vibration damping. During the grinding and lapping processes of manufacturing silicon wafers, excessive vibrations may cause subsurface damage which requires additional polishing and reduces yield. Nine compositions containing various levels of granulated rubber and glass fibers were manufactured. CRM WRF-10 granulated rubber was examined at 0%, 5%, and 10% and Corning Cem-Fil glass fibers were added at 0%, 0.5%, and 1% by weight. Smooth-On EpoxAcast 690 epoxy resin was held constant at 16% for each composition. Crushed granite aggregate from Martin Marietta, …

Model-Based Design Of An Optimal Lqg Regulator For A Piezoelectric Actuated Smart Structure Using A High-Precision Laser Interferometry Measurement System, Grant P. Gallagher

Master's Theses

Smart structure control systems commonly use piezoceramic sensors or accelerometers as vibration measurement devices. These measurement devices often produce noisy and/or low-precision signals, which makes it difficult to measure small-amplitude vibrations. Laser interferometry devices pose as an alternative high-precision position measurement method, capable of nanometer-scale resolution. The aim of this research is to utilize a model-based design approach to develop and implement a real-time Linear Quadratic Gaussian (LQG) regulator for a piezoelectric actuated smart structure using a high-precision laser interferometry measurement system to suppress the excitation of vibratory modes.

The analytical model of the smart structure is derived using the …

Synthesis And Property Characterization Of Rare-Earth High-Entropy Oxides With Pyrochlore-Type Structures, Candice Kinsler-Fedon

Doctoral Dissertations

In the search for novel materials with advanced physical properties, the concept of adding configurational entropy onto a single atomic site is known to provide new avenues toward material discovery. In the case of high entropy oxides (HEOs), the ability to “tune” a material’s properties by having multiple cations on single or multiple sites allows for greater opportunity to design materials for specific applications. The work presented here explores the synthesis of new multicomponent (high entropy) oxides, followed by a detailed characterization using several techniques. We have successfully synthesized multiple single-phase polycrystalline rare-earth high entropy oxides and grown large, bulk …

Synthesis Of Monodisperse Nanoscintillators At High Temperatures For Biomedical Relevant Applications, Eric Zhang

All Dissertations

Luminescent sub-100 nm particulates continuously generate immense research interest in the biomedical field for imaging, theranostics, and optogenetics. Conventionally, upconversion nanoparticles or UV activated semiconductors are studied, however these materials are limited by biological barriers such as the skin which reduces the penetration depth of these excitation sources, tissue's auto- fluorescence, and toxicity. One approach to overcome these challenges is to use nanoscintillators (sub-100 nm materials that can generate visible light using high energy excitation sources such as x-rays) which can generate light locally to the human body. Numerous scintillators have been reported since the discovery of x-rays from the …

Near-Earth Ion Irradiation Effects On Functional Ceramic Materials: A Combined Experimental-Monte Carlo Approach, William J. Sands

All Theses

The near-Earth space radiation environment is a complex system that creates a harmful environment for materials to operate in. Motivated by the search for using optical defects as an indicator of radiation damage, five single-crystal functional ceramic materials were selected to undergo ion irradiation at conditions found in the near-Earth space environment. Due to the complex nature of ion irradiation effects in ceramic materials, a host of calculations and experimental characterization methods were used. Calculations using the 2013 SRIM code were used to evaluate the ion projected range and the type and number of defects (vacancies) created by ion irradiation. …

Manufacturing Of A Ceramic Turbine Rotor For A Compact Jet Engine, Bryan T. Leicht

Theses and Dissertations

The primary goal of this study was to develop a low-cost, timely, scalable manufacturing method that produced a ceramic turbine that can be tested as a drop-in replacement on a JetCat P400 small scale gas turbine engine. This research compared two processes for manufacturing a ceramic turbine utilizing a pour casting method and 3D printing using stereolithography ceramic manufacturing (SLCM). The pour casting method used Silicon Nitride to create a cast turbine using a sacrificial 3D printed mold. The SLCM method evaluated producing an alumina turbine using an ADMATEC Admaflex 300 SLCM printer to directly print a ceramic turbine. This …

Thermal Considerations For Film Cooling Materials With Anisotropic Thermal Conductivity, Carol E. Bryant

Theses and Dissertations

Higher performance requirements and reduced core sizes are driving increases in turbine inlet temperature in gas turbine engines, surpassing the melting point of advanced materials. Newer materials, such as composites, are being introduced into the hot sections of gas turbine engines. Components in the hot section use film cooling to prevent melting. One unique aspect of some high-temperature composites is they have a bulk anisotropic thermal conductivity, therefore heat flow differs relative to traditional metallic components. Film cooling designs can be revolutionized by leveraging anisotropy in high-temperature materials. The purpose of this research is to examine thermal considerations for using …