Environmental Design Commons^™

A Prediction Method For Overall Economic Value Of Fault Detection And Diagnostic Tools For Rooftop And Split Systems, David Yuill, James Braun

Durham School of Architectural Engineering and Construction: Faculty Publications

Fault detection and diagnostics (FDD) tools for air-conditioning application may perform well or poorly, but it is difficult to characterize this performance in a meaningful way. Some recently proposed evaluation techniques have provided various statistics to characterize FDD performance, but these results can be difficult for a potential adopter of FDD to understand. A new method of characterizing FDD performance by predicting the overall economic value of the FDD tool is proposed in this paper. It is applicable to FDD tools intended for air-cooled unitary airconditioners, such as rooftop units (RTU) and split systems. The method gives an estimated dollar …

Normalized Effect Of Condenser Fouling And Refrigerant Charge On Performance Of Vapor Compression Air Conditioning Systems, Mehdi Mehrabi, David Yuill

Durham School of Architectural Engineering and Construction: Faculty Publications

Several laboratory experiments have studied the effect of faults on vapor compression cycle air-conditioning systems. There has been a particular focus on refrigerant charge variation, which is believed to be quite common in air conditioners, and a lesser focus on heat exchanger fouling. The majority of the published results evaluate the fault effects on particular system operating parameters in one unit. For example, the effect on capacity and efficiency are typically evaluated. The results differ from one study to the next. The current paper summarizes the effects for all of the results available in the literature for condenser fouling and …

Student Absenteeism And The Comparisons Of Two Sampling Procedures For Culturable Bioaerosol Measurement In Classrooms With And Without Upper Room Ultraviolet Germicidal Irradiation Devices, Chunxiao Su, Josephine Lau, Shawn G. Gibbs

Durham School of Architectural Engineering and Construction: Faculty Publications

Upper room ultraviolet germicidal irradiance (UVGI) has been shown to reduce the concentration of bioaerosols in controlled chambers. However, there is a lack of experimental results on the reduction of bioaerosol concentrations by UVGI devices in actual uncontrolled buildings. This study was carried out in an American elementary school in the Midwest. Two sampling procedures were carried out in six selected classrooms with similar dimensions that were separated into two groups: (1) UVGI exposure group and (2) non-UVGI control group. Two-stage Tisch culturable impactors were utilized to collect airborne culturable bacteria and fungi. Monthly samples were collected during unoccupied period …

Fault Detection And Diagnosis Process For Oversizing Design On Multiple Packaged Air-Conditioning Units, Denchai Woradechjumroen, Haorong Li, Thanapat Promwattanapakee

Durham School of Architectural Engineering and Construction: Faculty Publications

Heating, ventilation, air-conditioning and Refrigeration (HVAC&R) systems are seldom designed or commissioned properly. The situation leads to abrupt or degradation faults resulting in inefficient energy uses, excessive energy consumption and high service costs. To solve these aforementioned problems, fault detection and diagnosis (FDD) is utilized to firstly detect any abnormal conditions of a system and then diagnoses and determines their causes. In order to apply this concept in HVAC oversizing designs, this paper proposes the state-of-art procedure of a FDD procedure for analyzing the inherently faulty design (oversizing) of multiple packaged air-conditioning units used to supply cooling for an open …

Compressor Having A Control And Dagnostic Module, Hung M. Pham, Fadi M. Alsaleem

Durham School of Architectural Engineering and Construction: Faculty Publications

An apparatus includes a Voltage sensor, a current sensor, and a controller. The Voltage sensor measures Voltage values of alternating current power Supplied to a capacitor. The capaci tor is electrically coupled to a compressor. The current sensor measures current values of the alternating current power. The controller is configured to receive the Voltage values and the current values. The controller is configured to determine a first power factor value based on at least one of the voltage values and at least one of the current values. The controller is configured to selectively detect a first capacitor fault in response …

Air Change Rate Vs Airflow Pathway: Bioaerosol Containment And Removal In Patient Rooms, Kevin R. Grosskopf

Durham School of Architectural Engineering and Construction: Faculty Publications

Recent studies have shown that higher air change rates may have the unintended consequence of creating turbulent airflows that entrain high concentrations of infectious particles within the breathing zone, and possibly, breakdown pressure relationships necessary to contain the spread of infectious particles to other clinical spaces.

Adaptive Predictive Functional Controller, Fadi Alsaleem, Arvind Rao

Durham School of Architectural Engineering and Construction: Faculty Publications

A controller device and a method for controlling a system that utilizes an adaptive mechanism to self-learn the system char acteristics and incorporates this adaptive self-learning ability to predict a control parameter correctly to provide precise control of a system component.

An Adaptive Photovoltaic Topology To Overcome Shading Effect In Pv Systems, Mohamed Amer Chaaban, Lana El Chaar, Mahmoud Alahmad

Durham School of Architectural Engineering and Construction: Faculty Publications

Shading in photovoltaic systems can cause many undesired effects.When shading occurs, the power generated from the PV system is much less than nominal power, increasing the electrical mismatching losses between PV system components. Active research to address this power loss focuses on static and adaptive systems.This paper addresses an adaptive system solution and proposes a new method to adaptively overcome losses due to shading during low radiation conditions. In addition, a statistical analysis for choosing the most feasible and efficient configuration for the system size is presented. The proposed system has been validated under shade conditions in a simulation and …

Building Envelope And Interior Grading Systems And Methods, Fadi Mohammad Alsaleem

Durham School of Architectural Engineering and Construction: Faculty Publications

A difference module determines differences between an out door ambient temperature and an indoor temperature, deter mines a first average of the differences, and determines a second average of the differences. A storing module stores a first data point, the first data point including the first average and a first total run time of a heating, ventilation, and/or air conditioning (HVAC) system, and stores a second data point, the second data point including the second average and a second total run time of the HVAC system. A fitting module fits a line to the first and second data points. An …

Speed And Resolution In The Age Of Technological Reproducibility, Shawn Taylor

Theses and Dissertations

The rate of acceleration of the biologic and synthetic world has for a while now, been in the process of exponentially speeding up, maxing out servers and landfills, merging with each other, destroying each other. The last prehistoric relics on Earth are absorbing the same oxygen, carbon dioxide and electronic waves in our biosphere as us. A degraded .jpeg enlarged to full screen on a Samsung 4K UHD HU8550 Series Smart TV - 85” Class (84.5” diag.). Within this composite ecology, the ancient limestone of the grand canyon competes with the iMax movie of itself, the production of Mac pros, …

A Review Of Approaches For Sensing, Understanding, And Improving Occupancy-Related Energy-Use Behaviors In Commercial Buildings, Hamed Nabizadeh Rafsanjani, Changbum R. Ahn, Mahmoud Alahmad

Durham School of Architectural Engineering and Construction: Faculty Publications

Buildings currently account for 30–40 percent of total global energy consumption. In particular, commercial buildings are responsible for about 12 percent of global energy use and 21 percent of the United States’ energy use, and the energy demand of this sector continues to grow faster than other sectors. This increasing rate therefore raises a critical concern about improving the energy performance of commercial buildings. Recently, researchers have investigated ways in which understanding and improving occupants’ energy-consuming behaviors could function as a cost-effective approach to decreasing commercial buildings’ energy demands. The objective of this paper is to present a detailed, up-to-date …

Use Of Fiber-Reinforced Cements In Masonry Construction And Structural Rehabilitation, Ece Erdogmus

Durham School of Architectural Engineering and Construction: Faculty Publications

The use of fiber reinforcement in traditional concrete mixes has been extensively studied and has been slowly finding its regular use in practice. In contrast, opportunities for the use of fibers in masonry applications and structural rehabilitation projects (masonry and concrete structures) have not been as deeply investigated, where the base matrix may be a weaker cementitious mixture. This paper will summarize the findings of the author’s research over the past 10 years in these particular applications of fiber reinforced cements (FRC). For masonry, considering both mortar and mortar-unit bond characteristics, a 0.5% volume fraction of micro fibers in type …

House As Mediator: Integrative Typology As Connector Between Land And Sea, Samantha Kudish

Architecture Thesis Prep

Rather than the water being an obstacle to coastal residential communities, water can act as an opportunity. Instead of barricading these areas from the water, integrating it with the area would create communities that are capable of living in unison with the ocean. This can introduce new typologies of housing that can withstand the continuing rise of sea levels. Blurring the line between land and sea by living with the sea will allow coastal regions to stay afloat, benefiting from ever-changing water conditions. A proposed new housing typology would introduce a new program to coastal neighborhoods, rather than putting up …

Building Envelope For Energy-Efficient Residential Homes, A Case Study For The U.S. Department Of Energy Challenge Home Student Design Competition, Milica Tajsic

UNLV Theses, Dissertations, Professional Papers, and Capstones

With the continuous rise of population and expansion of urban areas, the need for additional housing and infrastructure is growing rapidly. Building sector is consuming a vast majority of the natural resources to meet the needs of urbanization and is in need of efficient, sustainable solutions that are viable for the customer, the economy and the environment. The building sector is both the problem and the solution to the issues of the carbon footprint of our society (Architecture 2030, 2011).

The envelope (roofs, walls, and foundations) and windows typically account for 36% of overall energy use, or about 14.3 quads …

An Emerging Vocabulary: Architecture Of Performance, Jeremy H. Stock

Kaleidoscope

Re-chartered at the University of Kentucky in 2005, the Triangle Fraternity – a brotherhood of students studying Architecture, Engineering, and Sciences – now seeks to establish a visible presence by building a new fraternity house on-campus. To enable this investigation, professors Gregory Luhan, Peyman Jahed, and Bruce Walcott developed a design + energy studio experience that provided a framework for an integrated design team to use a systems-thinking approach to generate a range of scalable, net-zero energy prototypes. These prototypes can be applied in a variety of contexts and have the potential to address larger issues, such as energy efficiency …

Method And System For Optimal Coordination Control And Soft Repair Of Multiple Rooftop Heating And Cooling Units, Haorong Li

Durham School of Architectural Engineering and Construction: Faculty Publications

Techniques are described that may be implemented in an adaptive control device to regulate multiple zone environmental units based upon multiple temperature values and multiple airflow values, where each temperature value and each airflow value is related to the temperature and the airflow in a specific zone. In an implementation, the input interface of the adaptive control device is configured to receive multiple temperature values and multiple air flow values from multiple zone sensors. The adaptive control device may calculate multiple operational values based on the multiple temperature values and the multiple air flow values. An operational value indicates a …

The Influence Of National Culture On Effectiveness Of Safety Trainings During Postdisaster Reconstruction, Behzad Esmaeili, Kevin Grosskopf, Amy Javernick-Will

Durham School of Architectural Engineering and Construction: Faculty Publications

Non-English speaking workers constitute a disproportionately high number of workers involved in postdisaster reconstruction. Additionally, the rate of fatality among these workers is higher than the industry average. Research shows this population is more prone to unsafe behaviors in the working environment, conceivably because many of these workers are sent into the field prior to any formalized training. Recent studies show that the native culture of construction workers can impact risk-taking behavior. While numerous researchers have attempted to develop training materials for Hispanic workers, the number of studies that consider the impact of native culture on safety behavior is minimal. …

Virtual Surface Temperature Sensor For Multi-Zone Commercial Buildings, Yuebin Yu, Denchai Woradechjumroen, Daihong Yu

Durham School of Architectural Engineering and Construction: Faculty Publications

Multi-zone structure is commonly used in small commercial office buildings, retail stores and supermarket. While there is no adjacent wall between the zones, the impact of a neighbor zone on the current zone can be approximated and analyzed through the application of virtual walls. It is critical to accurately estimate the virtual wall surface temperature in order to evaluate the model uncertainty and apply improved supervisory control on multiple rooftop air-conditioning units (RTUs). We propose an innovative virtual surface temperature sensor based on system-identification to solve this challenge. The validation of the virtual temperature model is processed by the three …

Shallow Flat Soffit Precast Concrete Floor System, George Morcous, Maher Tadros

Durham School of Architectural Engineering and Construction: Faculty Publications

A precast concrete floor system that eliminates the need for column corbels and beam ledges while being very shallow. The main advantages of the present system include a span to-depth ratio of 30, a flat soffit, economy, consistency with prevailing erection techniques, and fire and corrosion protection. The present system consists of continuous precast columns, prestressed rectangular beams, hollow-core planks, and cast-in-place composite topping. Testing results have indicated that a 12 inch deep flat soffit precast floor system has adequate capacity to carry gravity loads (including 100 psf live load) in a 30 ft x 30 ft bay size. Testing …

Hybrid Of Natural Element Method (Nem) With Genetic Algorithm (Ga) To Find Critical Slip Surface, Shahriar Shahrokhabadi, Vahid Khoshfahm, Hamed Nabizadeh Rafsanjani

Durham School of Architectural Engineering and Construction: Faculty Publications

One of the most important issues in geotechnical engineering is the slope stability analysis for determination of the factor of safety and the probable slip surface. Finite Element Method (FEM) is well suited for numerical study of advanced geotechnical problems. However, mesh requirements of FEM creates some difficulties for solution processing in certain problems. Recently, motivated by these limitations, several new Meshfree methods such as Natural Element Method (NEM) have been used to analyze engineering problems. This paper presents advantages of using NEM in 2D slope stability analysis and Genetic Algorithm (GA) optimization to determine the probable slip surface and …

Factors Related To Women's Undergraduate Success, Tanya Michelle Baker

All-Inclusive List of Electronic Theses and Dissertations

No abstract provided.

To Lift The Leaden-Eyed: Ernest Boyer’S Career In Higher Education, Drew Moser

All-Inclusive List of Electronic Theses and Dissertations

No abstract provided.

Compression Testing And Failure Modes Of Steel-Concrete Composite (Sc) Structures For Nuclear Containment, Patrick Michael Wanamaker, Amit H. Varma

The Summer Undergraduate Research Fellowship (SURF) Symposium

Although being able to provide much cleaner power than burning coal and other fossil fuels, nuclear power plants are still a tough sell to the general public due to their history of being spontaneously dangerous. The containment structures surrounding these nuclear plants, however, can play a huge role in reducing the risks associated with them. Relatively new designs for these containment assemblies, known as SC (steel-concrete composite) structures, aim to increase the strength and durability of the containment facilities while keeping costs down. By varying the spacing between shear studs, the ratio of concrete to steel, and the ratio of …

Evaluation Of Phase Change Materials For Cooling In A Super-Insulated Passive House, Jeffrey Stephen Lauck

Dissertations and Theses

Due to factors such as rising energy costs, diminishing resources, and climate change, the demand for high performance buildings is on the rise. As a result, several new building standards have emerged including the Passive House Standard, a rigorous energy-use standard based on a super-insulated and very tightly sealed building envelope. The standard requires that that air infiltration is less than or equal to 0.6 air changes per hour at a 50 Pascal pressure difference, annual heating energy is less than or equal to 15kWh/m2, and total annual source energy is less than or equal to 120 kWh/m2. A common …

Predicting Building Energy Performance: Leveraging Bim Content For Energy Efficient Buildings, Eddie Villanueva Aquino

Master's Theses

Reducing and managing the environmental impacts of building structures has become a priority of building stakeholders and within the architecture, engineering and construction (AEC) community; although, conflicting approaches and methods to combat the issues are present. For example, green building standards are widespread throughout the world; however each one has its own characteristics and consequently its own specific requirements. While all have proven to be effective rating systems and have similar requirements, the distinguishing characteristic that separates them is their treatment of performance and prescriptive metrics. The feature they all severely lack or currently limit is the inclusion of strict …

Multi-Objective Time-Cost Optimization Using Cobb-Douglas Production Function And Hybrid Genetic Algorithm, Zhigang Shen, Ashkan Hassani, Qian Shi

Durham School of Architectural Engineering and Construction: Faculty Publications

Existing research on construction time-cost tradeoff issues rarely explore the origin of the crashing cost. Crashing cost function was either assumed without much justification, or came from historical data of some real projects. As a result the conclusions of the papers can hardly be used to guide allocations of labor and equipment resources respectively. The authors believe Cobb-Douglas function provides a much-needed piece to modeling the cost functions in the construction time-cost tradeoff problem during the crashing process. We believe this new perspective fills a gap of existing time-cost tradeoff research by considering project duration, labor and equipment cost as …

Survey Of Suitable Plants For Cal Poly's Green Wall, Katrina Burritt

Horticulture and Crop Science

Green wall technology is a growing industry in the United States and has been very successful for a several years throughout Europe. The objective of this survey was to study the success of several different species of plants on a vertical wall facing south at Cal Poly’s Horticultural Department Unit. At first the focus was aimed at using California native species, because it was thought that natives would be better acclimated to the exposure in this specific location. It became apparent that plants should not be selected for the wall based just on the fact that they are California natives. …

Effects Of Reverberation And Noise On Speech Comprehension By Native And Non-Native English-Speaking Listeners, Z. Ellen Peng, Lily M. Wang, Siu-Kit Lau, Adam M. Steinbach

Durham School of Architectural Engineering and Construction: Faculty Publications

Previous studies have demonstrated the negative impact of adverse signal-to-noise-ratios on non-native English-speaking listeners' performance on speech recognition using recall tasks, as well as implied that comprehension skills were more impaired than recognition skills under reverberation and noise. The authors have themselves previously conducted a pilot study on three native and three non-native Englishspeaking listeners to examine the effects of reverberation and noise using speech comprehension tasks. Those results suggested that speech comprehension performance is worse under longer reverberation times (RT), and that a longer RT is more detrimental to speech comprehension by non-native listeners than native listeners. This paper …

Acoustic Tweets And Blogs: Using Social Media In An Undergraduate Acoustics Course, Lily M. Wang

Durham School of Architectural Engineering and Construction: Faculty Publications

Each fall, the author teaches an undergraduate architectural acoustics course to around 40 third-year architectural engineering students at the University of Nebraska. Beginning in 2011, a social media component was introduced to explore the use of this technology and how it may supplement the students' learning experience. Students were given an opportunity to receive extra credit by using Twitter and/or blogging about course material using a set hashtag (#AE3300) or through the course website. Results were positive, and the author will discuss pros and cons that she has experienced in adding this social media component. Suggestions for future implementations and …

Building Fabric Design : Thermal Performance Standards, Joseph Little

Articles

This is the first of a series of articles using content from the new RIAI Building Fabric Design CPD which explores a range of themes of central importance to designing buildings that are highly energy efficient, genuinely compliant and perform to their design intent and specification. As the articles are short and the themes are often complex, they can be at best a short introduction to the issues raised. In this article we will look at the new minimum building fabric standards: these are far more onerous than much of the Industry understands.