Architectural Engineering Commons^™

Factors Influencing Crack-Induced Tensile Strength Of Compacted Soil, Tae Hyung Kim, Tae Hoon Kim, Gi Chun Kang, Louis Ge

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Mode I (tensile) fracture is the most commonly observed failure in Geostructure's resulting from cracks in soil. Direct or indirect tensile tests have been used to evaluate the tensile strength of geomaterials. in this paper, the unconfined penetration device and experimental procedure were modified to reduce measurement errors. It was then used to determine the tensile strength of compacted soil. Factors influencing the tensile strength of the compacted soil, including the plasticity index, rate of loading, and size of specimen were discussed in detail, as well as its reliability. Experimental results indicated that the modified, unconfined penetration technique is sufficiently …

Time-Weighted Average Spme Analysis For In Planta Determination Of Cvocs, Emily M. Sheehan, Matt A. Limmer, Philipp Mayer, Ulrich Gosewinkel Karlson, Joel Gerard Burken

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Potential of Phytoscreening for Plume Delineation at Contaminated Sites Has Promoted Interest in Innovative, Sensitive Contaminant Sampling Techniques. Solid-Phase Microextraction (SPME) Methods Have Been Developed, Offering Quick, Undemanding, Noninvasive Sampling Without the Use of Solvents. in This Study, Time-Weighted Average SPME (TWA-SPME) Sampling Was Evaluated for in Planta Quantification of Chlorinated Solvents. TWA-SPME Was Found to Have Increased Sensitivity over Headspace and Equilibrium SPME Sampling. using a Variety of Chlorinated Solvents and a Polydimethylsiloxane/carboxen (PDMS/CAR) SPME Fiber, Most Compounds Exhibited Near Linear or Linear Uptake over the Sampling Period. Smaller, Less Hydrophobic Compounds Exhibited More Nonlinearity Than Larger, More …

Quantifying The Life Cycle Benefits Of Performance-Based Design In Sustainable Design, David Isaac Carmona

Master's Theses

ABSTRACT

Quantifying the Life Cycle Benefits of Performance-Based Design in Sustainable Design

David Carmona

For this thesis, a method is developed and tested for use with performance based design to quantify the sustainable and financial benefits of designing buildings to a structural performance level higher than Life-Safety. This paper starts to answer the question, “which would be a better investment: build structures to a performance level of Immediate Occupancy (IO) with the likelihood of less damage and downtime after an earthquake or continue to build to the building code’s implied minimum performance level of Life-Safety (LS)?”

An ASCE 7-05 designed …

The Bridge Newsletter Spring 2012, Missouri University Of Science And Technology

The Bridge Newsletter

-Light-weight foam could cushion expensive bridge repairs
-New Chancellor
-The house of the future today
-High-tech approach to project management

2012 Scholarly Productivity Report, Missouri University Of Science And Technology

Civil, Architectural and Environmental Engineering Scholarly Productivity Reports

No abstract provided.

Effects Of Nano-Copper(Ii) Oxide And Nano- Magnesium Oxide Particles On Activated Sludge, Guoqiang Liu, Jianmin Wang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Effects of nano-copper (II) oxide (nano-CuO) and nano-magnesium oxide (nano-MgO) particles on activated sludge endogenous respiration (aerobic digestion), biochemical oxygen demand (BOD) biodegradation, and nitrification were investigated through respiration rate measurement. for comparison, the effects of Cu (II) and Mg (II) ions on activated sludge were also studied. Results indicated that soluble Cu (II) has half maximum inhibitory concentration (IC50) values of 19, 5.5, 53, and 117 mg Cu/L for endogenous respiration, BOD biodegradation, ammonium oxidation, and nitrite oxidation, respectively. However, nano-CuO only inhibited BOD biodegradation at 240 mg Cu/L or more, and its associated toxicity was primarily caused by …

Long-Term Performance Of Passive Materials For Removal Of Ozone From Indoor Air, C. J. Cros, Glenn C. Morrison, J. A. Siegel, R. L. Corsi

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The health effects associated with exposure to ozone range from respiratory irritation to increased mortality. in this paper, we explore the use of three green building materials and an activated carbon (AC) mat that remove ozone from indoor air. We studied the effects of long-term exposure of these materials to real environments on ozone removal capability and pre- and post-ozonation emissions. a field study was completed over a 6-month period, and laboratory testing was intermittently conducted on material samples retrieved from the field. the results show sustained ozone removal for all materials except recycled carpet, with greatest ozone deposition velocity …

An Improved Prediction Model For Spacecraft Damage Following Orbital Debris Impact, Joel E. Williamsen, William P. Schonberg

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper offers a new set of 'generic', data-Based hole size and crank length prediction models for spherical orbital debris particles impacting multi-plate targets at velocities up to ~12 km/s. the equations are applicable to a wide variety of spacecraft target configurations, but are limited to hole sizes above, but relatively near, the ballistic limit of the impacting particles. Additional work is underway to expand these models to diameters farther above the ballistic limit for the described shield types.

Breaking Internal Waves On A Shelf Slope Using Numerical Simulations, Subhas K. Venayagamoorthy, Oliver B. Fringer

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The subject of internal waves interacting with bottom topographic features in the ocean has received much attention in the past few decades. This heightened interest is mainly due to a conjecture that breaking internal waves at boundaries can be a significant source of turbulence, leading to mixing and transport in the ocean. In this paper, we present results from high-resolution three-dimensional numerical simulations of an internal wave interacting with a shelf break in a linearly stratified fluid in order to highlight the instabilities that contribute to wave breaking over topography. The results show the development of a nonlinear internal bolus …

Life Cycle Cost Analysis Under Ireland's Capital Works Management Framework, Dermot Kehily, Alan Hore

Conference papers

The Capital Works Management Framework (CWMF) is a structure that has been developed to deliver the Irish government’s objectives in relation to public sector construction procurement reform. This research provides practical guidance and assistance for construction cost professionals in carrying out Whole Life Cycle Cost Analysis (WLCCA) and producing Life Cycle Cost Models(LCCMs) under the CWMF. The research outlines how LCCA calculations can be carried out for cost planning purposes and recommends a standard methodology for presenting LCCMs under the CWMF. The CWMF states that Whole Life Costs (WLC) are an important consideration throughout the design process and should be …

2:1 The Paper Tube Project, Noel Brady

Articles

Review of applied technological solution to rapid building techniques using paper tube and analogous materials to create space enclosing geodesic systems.

Shake Table Testing Of A Utility-Scale Wind Turbine, Ian Prowell, Chia Ming Uang, Ahmed Elgamal, J. Enrique Luco, Lanhui Guo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Shake table tests were undertaken on a full-scale wind turbine (65-kW rated power, 22.6-m hub height, and 16-m rotor diameter) using the Network for Earthquake Engineering Simulation Large High Performance Outdoor Shake Table at the University of California, San Diego. Structural response characteristics and modal parameters are presented for base shaking imparted in two configurations, both parallel (configuration 1) and perpendicular (configuration 2) to the axis of rotation of the rotor. Results are summarized for a series of progressively stronger motions imparted in configuration 1, with analysis identifying damage sources leading to an overall loss in stiffness. Two sources of …

Modeling Unbound Granular Materials Under Complex Stress Paths, Cheng Chen, Louis Ge

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Developing reliable and versatile constitutive models for geomaterials has been challenging tasks for nonlinear finite element analysis of geotechnical engineering systems. the fuzzy set plasticity theory has been developed to account for the nonlinear soil stress-strain response under complex stress paths. the theory in many ways resembles the bounding surface plasticity, where the plastic modulus is a function of the distance between the current and image stress states in the stress space. based on the concept of fuzzy set theory in mathematics, a membership function whose value ranges from 1 and 0 is introduced in the Fuzzy Set Plasticity Theory …

Characterization Of Crushed Rock-Concrete Interface Behavior Through The Parallel Gradation Technique, Domenica Cambio, Xin Kang, Louis Ge

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The response of a soil-structure system subjected to monotonic or cyclic loading is influenced significantly by the mechanical behavior of soil-structure interface. in this paper, the friction characteristics of the crushed rock-concrete interface and the role of the crushed rock deformability were examined through a series of monotonic and cyclic direct shear tests. the physical modeling technique of parallel gradation was adopted where two parallel gradation curves of the crushed rocks were prepared and used in the tests. the tests were carried out in dry condition and with two initial void ratios representing both loose and dense states. Two concrete …

Measuring Global Response Of A Wind Turbine To Simulated Earthquake Shaking Assisted By Point Tracking Videogrammetry, Ian Prowell, Tim Schmidt, Ahmed Elgamal, Chia Ming Uang, Hal Romanowitz, J. Edward Duggan

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Experiments investigating earthquake response of structures traditionally use conventional wired instruments such as strain gauges, displacement transducers, and accelerometers deployed at key areas of interest throughout structure. for wind turbines the rotor is one of these key areas, but due to rotation it is not possible to use wired instruments without a special slip ring. in a recent experiment conducted using the Network for Earthquake Engineering Simulation (NEES) Large High Performance Shake Table (LHPOST) at the University of California, San Diego (UCSD) the global response of a full scale 65-kW turbine (22 m hub height) was monitored using a novel …

Application Of Threshold Concepts To Improve A Design-Focused Course In Transportation Engineering, Dan Cernusca, Ghulam Bham

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Design is an integral part of engineering courses. to address its associated problems, however, is a challenging task in instruction because of design's open-endedness and complexity. in this study, two theoretical models were implemented in an introductory transportation engineering course to address the challenges associated with design of a highway. First, the theoretical framework proposed by the threshold concepts model was used to identify a candidate concept for the instructional redesign process. Two major characteristics of threshold concepts, integrativity and transformativity, were used to identify horizontal alignment as a candidate concept for the highway design process. Second, concept mapping was …

Evaluation Of Pre-Consolidation Stress Determination Methods, Omar Conte, Stephanie Rust, Louis Ge, Richard Wesley Stephenson

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Pre-Consolidation Pressure Provides Valuable Information About Soil Behavior And, Specifically, Settlement under an Induced Load. Soil is Expected to Have Less Settlement Before its Pre-Consolidation Pressure and Much More Settlement after that Point. the Pre-Consolidation Pressure and the Compressibility of the Soil Can Be Determined from the Results of a One-Dimensional Consolidation Test. Different Methods Have Been Developed to Obtain the Accurate Pre-Consolidation Pressure from One Dimensional Consolidation Test Data. This Paper Presents and Discusses the Results of the One-Dimensional Consolidation Test Data from an Extensive Testing Program. the Test Specimens Used Were Obtained from Multiple Borehole Locations and Were …

Life Cycle Costing Template (Excel), Dermot Kehily

Reports

No abstract provided.

Longitudinal Evaluation Of A Gis Laboratory In A Transportation Engineering Course, Ghulam H. Bham, Dan Cernusca, Ronaldo Luna, Uday R.R. Manepalli

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper focuses on the potential impact of student-centered feedback for enhancing the learning experience of civil engineering students that used a geographic information system (GIS) based tutorial in a transportation engineering course. the tutorial was implemented in a laboratory environment developed as a self-guided activity supported by a web-Based learning system. the formative research proposed in this study includes a series of four successive implementations of this laboratory. Students' performance, beliefs, and perceptions were monitored by using a mixed methods design approach and weaknesses identified from early implementations were addressed before the next implementation of the laboratory activity. the …

Monitoring The Early-Age Hydration Of Self-Compacting Concrete Using Ultrasonic P-Wave Transmission And Isothermal Calorimetry, Bram Desmet, Kelly Chrysanthe Atitung, Miguel Angel Abril Sanchez, John Vantomme, Dimitri Feys, Nicolas Robeyst, Katrien Audenaert, Geert De Schutter, Veerle Boel, Gert Heirman, Özlem Cizer, Lucie Vandewalle, Dionys Van Gemert

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Early-Age Hydration (B48 H) of a Series of Self-Compacting Concretes and Corresponding Mortars and One Traditionally Vibrated Concrete and Mortar is Monitored in a Continuous Way using Ultrasonic Testing and Isothermal Calorimetry. the Mixtures Differ in Type of Mineral Addition, Superplasticizer, Cement, Cement-To-Powder Ratio and Water-To-Powder Ratio. the Influence of These Different Mixture Compositions on the Kinetics of the Hydration during the First Days of the Hydration is Characterized by the Heat Production Rate Q and the Evolution of the P-Wave Velocity, which is a Consequence of the Microstructural Changes. the Variations in the Acceleration Caused by Mineral Additions …

Direct Shear Tests On Jsc-1a Lunar Regolith Simulant, Masafumi Iai, Ronaldo Luna

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

A series of direct shear tests were conducted on the JSC-1A lunar regolith simulant in a 101.6-mm- (4-in.-) diameter container. the direct shear test provides a unique mode of failure that aids the development of excavation tools for the Moon. Relative density and normal load were varied to study the strength behavior of such granular material at peak and critical state conditions. the values of the internal friction angle ranged from 30 to 70. a relationship between the internal friction angle of the direct shear and the published triaxial compression test results is presented. Additionally, the measured dilatancy angle is …

Remote Sensing Of Soil Moisture Using Airborne Hyperspectral Data, Michael Finn, Mark Lewis, David Bosch, Mario Giraldo, Kristina Yamamoto, Dana Sullivan, Russell Kincaid, Ronaldo Luna, Gopala Allam, Craig Kvien, Michael Williams

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Landscape assessment of soil moisture is critical to understanding the hydrological cycle at the regional scale and in broad-scale studies of biophysical processes affected by global climate changes in temperature and precipitation. Traditional efforts to measure soil moisture have been principally restricted to in situ measurements, so remote sensing techniques are often employed. Hyperspectral sensors with finer spatial resolution and narrow band widths may offer an alternative to traditional multispectral analysis of soil moisture, particularly in landscapes with high spatial heterogeneity. This preliminary research evaluates the ability of remotely sensed hyperspectral data to quantify soil moisture for the Little River …

Phytoscreening For Chlorinated Solvents Using Rapid In Vitro Spme Sampling: Application To Urban Plume In Verl, Germany, Matt A. Limmer, Jean Christophe Balouet, Frank Karg, Don A. Vroblesky, Joel Gerard Burken

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Rapid Detection and Delineation of Contaminants in Urban Settings is Critically Important in Protecting Human Health. Cores from Trees Growing above a Plume of Contaminated Groundwater in Verl, Germany, Were Collected in 1 Day, with Subsequent Analysis and Plume Mapping Completed over Several Days. Solid-Phase Microextraction (SPME) Analysis Was Applied to Detect Tetrachloroethene (PCE) and Trichloroethene (TCE) to Below Nanogram/liter Levels in the Transpiration Stream of the Trees. the Tree Core Concentrations Showed a Clear Areal Correlation to the Distribution of PCE and TCE in the Groundwater. Concentrations in Tree Cores Were Lower Than the Underlying Groundwater, as Anticipated; However, …

The Bridge Newsletter Winter 2011, Missouri University Of Science And Technology

The Bridge Newsletter

-Living intentionally: Meet the Oerthers
-Making a lasting impact
-Phytoforensics
-The simple things of life

Modern Protection Systems To Prevent Corrosion Of Structural Steel Elements Due To Deicing And Roadway Salts, John J. Myers, Wei Zheng

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The effectiveness of innovative polymeric coatings, polyurea and Poly aspartic polyurea, to protect structural steel from corrosion was investigated through standard laboratory tests. the coating evaluation tests included salt fog test, QUV weathering test, adhesion test, and freeze-thaw stability test. These tests were used to assess the long-term performance of coating technologies compared to the conventional polyurethane type coatings, i.e. coating systems with inorganic zinc primer, epoxy intermediate coat and polyurethane topcoat. This paper presents part of results in the aforementioned evaluation tests. the results illustrate that Poly aspartic coating systems are very promising for corrosion mitigation and can provide …

Correction Factors For An Analytical Method Of Pile Foundation Response Subjected To Horizontal Dynamic Vibrations, Domenica Cambio, Louis Ge

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pile foundation response due to horizontal vibration, it is known that the original Novak's method overestimates the dominant frequency and underestimates the dominant amplitude of pile head responses. It is found that reducing the pile-foundation system stiffness and damping coefficients would lead to a smaller dominant frequency and higher dominant amplitude, respectively. the objective of this paper is to evaluate and determine appropriate correction factors for stiffness and damping coefficients for the analytical model developed by Novak and El-Sharnouby (1983) to improve the theoretical predictions of pile foundations subjected to dynamic forces. the reduction factors were determined by continuously …

Accelerated Construction For Pedestrian Bridges: A Comparison Between High Strength Concrete (Hsc) And High-Strength Self Consolidating Concrete (Hs-Scc), John J. Myers, Kurt Bloch

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

High-strength concrete (HSC) and glass fiber reinforced polymer (GFRP) bars are materials utilized in bridge construction to lower cost, reduce construction time, and increase service life of bridge structures. Recently, high-strength self-consolidating concrete (HS-SCC), a highly flowable concrete that does not require vibration, has been developed as a viable alternative to HSC for use in situations with congested steel or a need for rapid construction. Coupling HS-SCC with GFRP bars could create durable structures built rapidly. Several performance related issues remain to be investigated such as the behavior of prestress loss, shear, creep, shrinkage, thermal gradients, mechanical property development, time …

Earthquake-Induced Deformation Analysis Of A Bridge Approach Embankment In Missouri, W. Liu, Ronaldo Luna, Richard Wesley Stephenson, S. Wang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Earthquake-Induced Deformations for a Bridge Approach Earth Embankment Are Predicted using a Calibrated Numerical Model. the Constitutive Soil Model is a Modified Hyperbolic Model that Uses Masing Rules and Incremental Pore Pressure Relations. the Model Was Calibrated using Both Laboratory and Field Data. a Shaking Table Physical Model Was Used to Verify the Numerical Simulation. Additionally, the Upper San Fernando Dam Was Modeled to Reproduce the Deformations in the 1971 Earthquake. the Subsurface and Embankment Soil Conditions Were Characterized using Field and Laboratory Methods. the Model Developed Was Used to Predict the Earthquake-Induced Deformations of an Approach Embankment to Bridge …

Influence Of Geotechnical Dataset On The Range Of Influence Of Undrained Shear Strength, Site Onyejekwe, Louis Ge

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The knowledge of the spatial variability of geotechnical parameters, which can be described statistically by the mean, the variance, and the scale of fluctuation, is important in reliability-Based design. of particular importance is the scale of fluctuation. It can be used to compute the variance reduction factor, a factor of spatial averaging of geotechnical properties to reduce their point variance. the most prevalent method of determining the scale of fluctuation uses datasets whose data points are at close and regular intervals, e.g. measurements from cone penetrometer soundings. Another method, when continuous measurements are not available, uses datasets that are widely …

Special Issue On The 6th International Phytotechnologies Conference, St. Louis, Missouri, 2009: Conference Review, Joel G. (Gerard) Burken, Jason C. White

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

No abstract provided.