Architecture Commons^™

Consolidation-Induced Solute Transport For Constant Rate Of Strain. Ii: Comparison With Incremental Loading, Patrick J. Fox, Hefu Pu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents a numerical investigation of one-dimensional large strain consolidation-induced solute transport for incremental loading (IL) and constant rate of strain (CRS) conditions. Solute transport accounts for advection, diffusion, dispersion, linear and nonlinear sorption, and equilibrium and nonequilibrium sorption, and is consistent with temporal and spatial variations of porosity and seepage velocity in the consolidating soil. Simulations were conducted using material properties for kaolinite clay and indicate that IL and CRS conditions produce significantly different responses during the course of consolidation, including applied stress, rate of settlement, excess pore pressure, and local strain. However, for a given set of …

Influence Of Portland Cement And Ground-Granulated Blast-Furnace Slag On Bleeding Of Fresh Mix, Hong Jae Yim, Jae Hong Kim, Seong Ho Han, Hyo Gyoung Kwak

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Bleeding occurs when freshly mixed cement-based materials settle in a form, and this phenomenon influences the quality of the fresh state as well as the hardened state. This paper attempts to measure the bleeding of Portland cement and ground granulated blast furnace slag (GGBFS) paste mixtures. To investigate the influence of water-to-powder ratio and the used powders under high pressure on bleeding, a pressure vessel and various types of freshly mixed paste were prepared. The packing density and permeability were measured and discussed to understand material effects on the bleeding phenomenon.

Consolidation-Induced Solute Transport For Constant Rate Of Strain. I: Model Development And Simulation Results, Hefu Pu, Patrick J. Fox

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

A numerical model, called CSTCRS1, is presented for coupled one-dimensional consolidation and solute transport under constant rate of strain (CRS) loading conditions. The consolidation algorithm accounts for vertical strain, general constitutive relationships, relative fluid velocity, changing compressibility and hydraulic conductivity during consolidation, and an external hydraulic gradient. The solute transport algorithm accounts for advection, dispersion, linear and nonlinear sorption, and equilibrium and nonequilibrium sorption. Soil compressibility is rate-independent and as such CSTCRS1 is more appropriate for less-structured soils. The model is based on a dual-Lagrangian framework that separately tracks the motions of sold and fluid phases. The development of CSTCRS1 …

Indygo Downtown Transit Center - Transforming Indianapolis, Ben Smith, Steve Robinson, Joe Fischer

Purdue Road School

The new IndyGo Downtown Transit Center will transform transit in downtown Indianapolis and offers lessons in transit planning, traffic planning, intermodal connectivity, public engagement, and pedestrian access. This presentation will give an overview of the facility and then focus on attributes of the facility and of the design process that might offer useful lessons to other transit projects, including those of a smaller scale

Moor Movement: Automated Docking On Drought-Stricken Reservoirs, Daniel Beck

Landscape Architecture

Moor Movement establishes a mechanized docking system for unpredictable shoreline fluctuations on inland lakes and reservoirs. Due to climate change and warmer global temperatures, the threat of ocean level rise has initiated massive proposals to address the interface between ocean and man-made infrastructure. While this is a monumental problem, ocean level rise is not the only immediate threat. The recently declared emergency drought conditions in California are finally bringing attention to inland lakes and reservoirs. While ocean levels might rise 2-7 feet in 100 years, a lake could drop 100 feet in 5 years. What happens to access roads, marinas, …

Building And Growing With Mobile Technology, Chris Lierheimer

The Professional Constructor

Today’s construction managers have an arsenal of mobile technologies at their disposal, all of which make managing projects vastly more organized and efficient than ever before. In this paper, I will explore in detail three different mobile technologies that the modern contractor has at his or her disposal, their benefits, potential pitfalls that they may present, and my thoughts on the future of these tools. I will share personal experience with, and research based on topics ranging from building information modeling, to RFID chip tracking of resources, to cloud based programs that streamline information flow.

Using Mobile Technology For Managing Construction Projects, Paul Shaw

The Professional Constructor

This essay examines the use and application of emerging mobile technologies in the construction industry. Mobile phones and tablets are discussed in-depth, and can be used to replace office tools, to collaborate, and to bring building information modeling (BIM) technology out into the field. Next, wearable computing technology is discussed, including Google Glass and smart hard hats. This technology provides another avenue for construction information access in the field. Finally, unmanned aerial vehicles are discussed, along with their challenges and potential benefits. Increased technology use will absolutely improve efficiency and profitability in the construction industry.

Solar Orientation For Low-Energy Residential Building In Pagosa Springs, Colorado, Torry D. Hessman, Caroline M. Clevenger, Maryellen C. Nobe, Katharin Leigh

The Professional Constructor

This research compares the energy performance of 43 homes. Seven homes, constructed by a single builder using passive design principles, are the focus of the study. The remaining 36 homes, more conventionally built, establish a baseline for local residential energy performance. All of the homes are located within a six square-mile geographical region in Pagosa Springs, Colorado. Researchers collected utility data over a two year period, from September 2009 to August 2011. While other factors impact performance, for this study the dependent variable was energy consumption in British Thermal Units (BTUs) per square foot per season. The independent variable was …

Adoption Of Green Building Guidelines In Usa, India, And China, Matt Syal, Yunhui Yang, Gayatri Kumar, Jawanda Jackson

The Professional Constructor

Green Building Guidelines (GBGs) have played a major role in the global efforts to develop environmentally responsible buildings and infrastructure. These guidelines serve as ratings tools to evaluate sustainable practices used in buildings’ design, construction, and operations. Although, the acceptance of these guidelines has begun to increase globally, only a few countries have seen their widespread adoption. The acceptance of GBGs is dependent upon various factors specific to the country and society in which they exist. USA, India, and China were selected to be the focus of this study since each of these countries present a unique set of societal …

Characterizing Equipment Cost, Fuel Use, And Emissions For Earthwork Activities, Phil Lewis, Yongwei Shan, Apif Hajji, Elizabeth Hazzard

The Professional Constructor

The objective of this paper is to examine the relationships between construction equipment costs, fuel use, and air pollutant emissions to make more informed decisions in construction planning and achieve more sustainable construction activity. This paper presents an estimating approach that combines both construction and environmental data to assess the relationships between equipment costs, fuel use, and emissions. To characterize these relationships, a case study is presented for a dozer performing a bulk excavation activity. Sensitivity analyses based on soil type, dozing distance, and engine horsepower rating are presented. Results indicate that there is little difference in the equipment total …

General Interest Articles, American Institute Of Constructors

The Professional Constructor

No abstract provided.

Assessing The Economic, Energy, And Environmental Impacts Of A Bridge Replacement Project, Elizabeth Hazzard, Phil Lewis

The Professional Constructor

As the nation moves toward more sustainable energy and environmental standards, it is important to examine all sources of fuel consumption and pollution, including heavy-duty diesel (HDD) construction equipment. In order to quantify these sources at the project level, they must be identified with their respective activities. A case study was performed on an Oklahoma Department of Transportation (ODOT) bridge replacement project in order to establish a baseline estimate of real-world equipment activity, fuel use, and emissions data. These data were collected on a daily basis via jobsite visits and included specific information such as the equipment’s model year, engine …

In Memory Of Fran Dugan, American Institute Of Constructors

The Professional Constructor

No abstract provided.

Analysis Of Green Building Initiatives On U.S. University Campuse, Dennis C. Bausman, Ben Mueller

The Professional Constructor

As population expands and resource consumption grows, interest in sustainable practices continues to intensify. Universities and colleges in the U.S. have been leading the trend toward building certification and green initiatives to reduce energy consumption, lower water consumption, and recycle solid waste. This study investigates the extent to which green practices are implemented on new construction and the renovation of existing building stock on university campuses across the United States. The study also examines the financial analysis techniques institutions use to assess and prioritize green initiatives on new and existing facilities. The population selected for this study was two hundred …

Full Issue, Volume 39, Number 1

The Professional Constructor

No abstract provided.

Bs News March/April

Building Services Engineering

No abstract provided.

The Bridge Newsletter Spring 2015, Missouri University Of Science And Technology

The Bridge Newsletter

-Wastewater treatment technologies that cost less and save energy
-Open windows and air quality
-Bartels displays research
-NASA honors Schonberg

The 2014 François Naftali Frenkiel Award For Fluid Mechanics, Benjamin D. Mater, Simon M. Schaad, Subhas Karan Venayagamoorthy

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

No abstract provided.

Bs News January/February

Building Services Engineering

No abstract provided.

Vibration Of Steel-Framed Floors Supporting Sensitive Equipment In Hospitals, Research Facilities, And Manufacturing Facilities, Di Liu

Theses and Dissertations--Civil Engineering

Floors have traditionally been designed only for strength and deflection serviceability. As technological advances have been made in medical, scientific and micro-electronics manufacturing, many types of equipment have become sensitive to vibration of the supporting floor. Thus, vibration serviceability has become a routinely evaluated limit state for floors supporting sensitive equipment. Equipment vibration tolerance limits are sometimes expressed as waveform peak acceleration, and are more often expressed as narrowband spectral acceleration, or one-third octave spectral velocity.

Current floor vibration prediction methods, such as those found in the American Institute of Steel Construction Design Guide 11, Floor Vibrations Due to Human …

Accounting For The Short Term Substitution Effects Of Walking And Cycling In Sustainable Transportation, Daniel P. Piatkowski, Kevin J. Krizek, Susan L. Handy

Community and Regional Planning Program: Faculty Scholarly and Creative Activity

The environmental benefits of bicycling and walking depend on the degree to which their use substitutes for car driving. Assuming that every walking and bicycling trip replaces a driving trip is likely to produce overestimates of the potential for such modes to reduce vehicle travel and city-scale greenhouse gas emissions. Measuring this ‘‘substitution effect’’ is not straightforward. There are many dimensions of the substitution effect, including trip type, substituting mode, extent, time horizon, and activity patterns. Previously used approaches to measure substitution include indirect inference and direct questioning. This study piloted an intercept survey using the direct questioning approach at …

Development Of Composite Pcms By Incorporation Of Paraffin Into Various Building Materials, Shazim Ali Memon, Wenyu Liao, Shuqing Yang, Hongzhi Cui, Syed Farasat Ali Shah

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this research, we focused on the development of composite phase-change materials (CPCMs) by incorporation of a paraffin through vacuum impregnation in widely used building materials (Kaolin and ground granulated blast-furnace slag (GGBS)). The composite PCMs were characterized using environmental scanning electron microscopy (ESEM), Fourier transform infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. Moreover, thermal performance of cement paste composite PCM panels was evaluated using a self-designed heating system. Test results showed that the maximum percentage of paraffin retained by Kaolin and GGBS was found to be 18% and 9%, respectively. FT-IR results show that …

A Shear-Based Parameterization Of Turbulent Mixing In The Stable Atmospheric Boundary Layer, Jordan M. Wilson, Subhas K. Venayagamoorthy

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this study, shear-based parameterizations of turbulent mixing in the stable atmospheric boundary layer (SABL) are proposed. A relevant length-scale estimate for the mixing length LM of the turbulent momentum field is constructed from the turbulent kinetic energy Ek and the mean shear rate S as. Using observational data from two field campaigns-the Surface Heat Budget of the Arctic Ocean (SHEBA) experiment and the 1999 Cooperative Atmosphere-Surface Exchange Study (CASES-99)- is shown to have a strong correlation with LM. The relationship between LM and corresponds to the ratio of the magnitude of the tangential components of the turbulent momentum flux …

Hydraulic Design Of Baffles In Disinfection Contact Tanks, Zachary H. Taylor, Jeremy S. Carlston, Subhas Karan Venayagamoorthy

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study focuses on understanding the hydraulic design of baffled contact tanks using computational fluid dynamics simulations. In particular, we address the key question: for a given footprint of a rectangular tank with a specified inlet width (Winlet), how does the hydraulic efficiency of a baffled tank depend on the configuration of internal baffles? In an effort to address this question, a carefully conceived parametric study consisting of 30 high-resolution two-dimensional (planar) simulations was conducted to quantify the hydraulic efficiency of a laboratory scale tank as a function of dimensional relationships between key baffle design dimensions (baffle opening length Lbo, …

Comparisons Of Horizontal-Axis Wind Turbine Wake Interaction Models, Jordan M. Wilson, Cole J. Davis, Subhas K. Venayagamoorthy, Paul R. Heyliger

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this study, Reynolds-averaged Navier-Stokes (RANS) simulations are performed using the k-ϵ and k-ω shear stress transport (SST) turbulence closure schemes to investigate the interactions of horizontal-axis wind turbine (HAWT) models in the neutrally stratified atmospheric boundary layer (ABL). A comparative study of actuator disk, actuator line, and full rotor models of the National Renewable Energy Laboratory (NREL) 5 MW reference turbine is presented. The open-source computational fluid dynamics (CFD) code open foam 2.1.0 and the commercial software ANSYS fluent 13.0 are used for simulations. Single turbine models are analyzed for turbulent structures and wake resolution in the downstream region. …

The Formation And Fate Of Internal Waves In The South China Sea, Matthew H. Alford, Thomas Peacock, Jennifer A. Mackinnon, Jonathan D. Nash, Maarten C. Buijsman, Luca A. Centurioni, Shenn-Yu Chao, Ming-Huei Chang, David M. Farmer, Oliver B. Fringer, Ke-Hsien Fu, Patrick C. Gallacher, Hans C. Graber, Karl R. Helfrich, Steven M. Jachec, Christopher R. Jackson, Jody M. Klymak, Dong S. Ko, Sen Jan, T. M. Shaun Johnson, Sonya Legg, I-Huan Lee, Ren-Chih Lien, Matthew J. Mercier, James N. Mourn, Ruth Musgrave, Jae-Hun Park, Andrew I. Pickering, Robert Pinkel, Luc Rainville, Steven R. Ramp, Daniel L. Rudnick, Sutanu Sarkar, Alberto Scotti, Harper L. Simmons, Louis C. St. Laurent, Subhas Karan Venayagamoorthy, Yu-Huai Wang, Joe Wang, Ying J. Yang, Theresa Paluszkiewicz, Tswen-Yung David Tang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Internal gravity waves, the subsurface analogue of the familiar surface gravity waves that break on beaches, are ubiquitous in the ocean. Because of their strong vertical and horizontal currents, and the turbulent mixing caused by their breaking, they affect a panoply of ocean processes, such as the supply of nutrients for photosynthesis¹, sediment and pollutant transport² and acoustic transmission³; they also pose hazards for man-made structures in the ocean⁴. Generated primarily by the wind and the tides, internal waves can travel thousands of kilometers from their sources before breaking⁵, making it …

2015 Scholarly Productivity Report, Missouri University Of Science And Technology

Civil, Architectural and Environmental Engineering Scholarly Productivity Reports

No abstract provided.

Biases In Thorpe-Scale Estimates Of Turbulence Dissipation. Part I: Assessments From Large-Scale Overturns In Oceanographic Data, Benjamin D. Mater, Subhas K. Venayagamoorthy, Louis St Laurent, James N. Moum

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Oceanic density overturns are commonly used to parameterize the dissipation rate of turbulent kinetic energy. This method assumes a linear scaling between the Thorpe length scale LT and the Ozmidov length scale LO. Historic evidence supporting LTLO has been shown for relatively weak shear-driven turbulence of the thermocline; however, little support for the method exists in regions of turbulence driven by the convective collapse of topographically influenced overturns that are large by open-ocean standards. This study presents a direct comparison of LT and LO, using vertical profiles of temperature and microstructure shear collected in the Luzon Strait-a site characterized by …

Lighting Design In Europe: Aligning The Demands For Lower Energy Usage With Better Quality., Kevin Kelly, James Duff

Articles

Lighting design is one of the fastest changing areas in building engineering. It has evolved significantly in recent years due to changing technology and demands for improved quality, better control, reduced energy and sustainability. This paper is an overview of what is happening in Europe and elsewhere and examines the literature to find that latest recommendations in the Code for Lighting issued by the SLL (Society of Light and Lighting) in the UK change previous demands for equal illuminance across a working plane to more specific and demanding criteria. There are recommendations for qualitative metrics and better distribution of light …

Model For Consolidation Analysis Of Layered Soils Under Depth-Dependent Loading, Hefu Pu, Patrick J. Fox

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

A numerical model is presented for one-dimensional large strain consolidation of a layered soil stratum. The algorithm accounts for vertical strain, soil self-weight, conventional constitutive relationships, changing material properties during consolidation, unload/reload, time-dependent loading and boundary conditions, an externally applied hydraulic gradient, and multiple soil layers with different material properties. The model can also accommodate depth-dependent loading and variable preconsolidation stress profiles. Verification checks of the model show excellent agreement with available analytical and numerical solutions for consolidation of soils with multiple layers and depth-dependent loading. An overview of this model is presented, and a parametric study is performed to …