Open Access. Powered by Scholars. Published by Universities.®

Digital Commons Network™

Open Access. Powered by Scholars. Published by Universities.®

Engineering

Discipline
Institution
Publication Year
Publication
Publication Type
File Type

Articles 61 - 90 of 2079

Full-Text Articles in Entire DC Network

Numerical Study Of Effect Of Using Nanofluids Flowing In Simply Supported Pipes On Vibrations Characteristics, Kadhum A. Jehhef, Mohamed A. Siba, Hayder S. Abdulamir Aug 2026

Numerical Study Of Effect Of Using Nanofluids Flowing In Simply Supported Pipes On Vibrations Characteristics, Kadhum A. Jehhef, Mohamed A. Siba, Hayder S. Abdulamir

Engineering and Technology Journal

In general, internal vibrations within the pipelines caused by fluids being passing through a pipeline system can cause. These pipeline system can damage by the sudden amplified vibrations that weren’t considered at the design of the system, and flow induced vibrations resonate with the pipes natural frequency. Therefore, it is important to predict and identify the pipeline system vibrations during its lifetime. In this study by using MATLAB code as a CFD solver, it studied the forced and free vibrations caused by fluid flows at Reynolds number ranged as 0 < Re < 2500 for laminar flow and ranged as 104 < Re < 105 for turbulent flow. The working fluid has chosen as of (Al2O3, TiO2, SiO2 and water) with different nanoparticle volume fraction of (0 to 2% vol.). These fluids flow in simply supported pipe with different lengths and diameters. The results presented the effect of pipe and fluid parameter upon the fluid critical velocity and fundamental natural frequencies. The results showed that the pipe natural frequency increased with increasing with decreasing the pipe length and diameter. In addition, it showed that the pipe natural frequency decreased when using the different nanoparticle depressed in the water and with increasing the volume fraction.

Go to article

Design Pid Neural Network Controller For Trajectory Tracking Of Differential Drive Mobile Robot Based On Pso, Mohamed Mohamed, Mohammed Hamza Aug 2026

Design Pid Neural Network Controller For Trajectory Tracking Of Differential Drive Mobile Robot Based On Pso, Mohamed Mohamed, Mohammed Hamza

Engineering and Technology Journal

This paper introduces a nonlinear (Proportional-Integral-Derivative Neural Network) (PID NN) controller for a differential wheeled mobile robot trajectory tracking problem. This neural controller is built based on the principles of neural network (NN) and the equation of conventional structure of PID controller and is applied on kinematic model of the mobile robot. The particle swarm optimization algorithm (PSO) is utilized to find the best values of three PID NN parameters and connection weights that minimize the error between the reference path and the actual path. The results illustrate that the PID NN controller has a satisfied ability to make the …

Go to article

Enhancement Of Surface Crack Density Produced By Edm Using Hybrid Machining, Saad Shather, Shukry Aghdeab, Waqass Khudier Aug 2026

Enhancement Of Surface Crack Density Produced By Edm Using Hybrid Machining, Saad Shather, Shukry Aghdeab, Waqass Khudier

Engineering and Technology Journal

The present work is aimed to improve the surface cracks density of electrical discharge machining (EDM) by Electrical Discharge Machining (EDM)/Electrochemical Machining (ECM) EDM/ECM hybrid process. A hybrid method of EDM-ECM combined processing involve EDM shaping as well as electrochemical machining (ECM) finishing, also, they are conducted in sequence one same machine tool, same electrode, yet on the different dielectric. In this study, the used workpiece material is the A2-Tool Steel material, while the electrode material is copper. The influence of controllable parameters could be identified via response surface methodology (RSM), these controllable effects include: pulse current, pulse on time, …

Go to article

State Space Parallelization Method For A 16-Bit Turbo Encoder, Maha Fleah, Qusay Al-Doori Aug 2026

State Space Parallelization Method For A 16-Bit Turbo Encoder, Maha Fleah, Qusay Al-Doori

Engineering and Technology Journal

Turbo codes are widely used in digital communication systems. Their ability to reach the Shannon channel capacity made it the choice for most of the communication systems. Due to the huge amount of the transmitted data, there is a need to increase the processing speed of the encoders. The researchers used the state space technique to enhance the throughput of the turbo encoder. They apply it to increase the turbo encoder throughput from one bit per cycle up to 8 bit per cycle. The researchers applied the state space method to a three-flip flop, eight state Recursive Systematic Convolution Code …

Go to article

Numerical Investigations On Seismic Response Of Structures Under The Effect Of Infinite Boundary Of Soil-Structure Interaction, Qais Hasan, Saad Al-Wakel, Zahraa Zaidan Aug 2026

Numerical Investigations On Seismic Response Of Structures Under The Effect Of Infinite Boundary Of Soil-Structure Interaction, Qais Hasan, Saad Al-Wakel, Zahraa Zaidan

Engineering and Technology Journal

The damage caused by large earthquakes is not only due to structures but also due to the soil failure, where the dynamic response varies considerably from the fixed base state because of the interaction between the ground and the structure. The main objective of this paper is to study the effect of the infinitely extended soil on the dynamic response of the structure. A three-dimensional dynamic analysis of reinforced concrete buildingconsidering the effect of soil-structure interaction is performed. Building with a different number of stories rest on soil with various characteristics have been taken into consideration. For simulation of wave …

Go to article

Design And Control Of A Full-Scale Quarter Car Test Rig For Semi-Active Suspension System, Bahaa-Aldin Abdullah, Mohsin Hamzah, Ammar Merza Aug 2026

Design And Control Of A Full-Scale Quarter Car Test Rig For Semi-Active Suspension System, Bahaa-Aldin Abdullah, Mohsin Hamzah, Ammar Merza

Engineering and Technology Journal

Passive hydraulic dampers are commonly used in the automotive suspension system. Nevertheless, they are suffering from a significant drawback owing to the changing of its characteristics at high-frequency; as a result, decreasing the ride quality due to the increase of the transmitted force, especially at high frequency excitations. The present work developed a semi-active suspension system to solve this problem with its effect. A Sky-hook control strategy is used to suppress the positional oscillation of the sprung mass in the presence of road irregularities via the use of the electrohydraulic (EH) damper, as an objective. In order to apply the …

Go to article

An Overview On Most Effective Dras In Crude Oil Pipelines, Raheeq Ibrahim, Manal Odah, Dhoha Shafeeq Aug 2026

An Overview On Most Effective Dras In Crude Oil Pipelines, Raheeq Ibrahim, Manal Odah, Dhoha Shafeeq

Engineering and Technology Journal

The flow of crude oil in pipelines suffers from a problem of fluid flow pressure drop and high-energy consumption for pumping especially in low temperatures environment. Flow can be enhanced using viscosity either reduction or drag reduction techniques. Drag reduction is considered as the most effective and most applicable method. The technique contributes in reducing the frictional energy losses during the flow by addition of little doses of materials knowing as drag-reducing agents. The present work focuses on more recent and most applicable drag-reducing agents used in crude oil flow enhancement via pipelines.

Go to article

Smoothing Smartphone Gps Raw Measurements, Tariq Ataiwe, Abbas Khalaf, Israa Mohammed Aug 2026

Smoothing Smartphone Gps Raw Measurements, Tariq Ataiwe, Abbas Khalaf, Israa Mohammed

Engineering and Technology Journal

This  research aims  to  investigate  the  smoothing  of  the  pseudo-range raw  measurements  of  the  smartphone  using  a  Hatch  filter.  The  measurements  of  smartphones  suffer  from  high  noise  generated  from  low-cost  antennas  and  oscillators, which are designed to work in a certain way. These types of low-cost antennas  and  oscillators  are  entirely different  from  geodetic  instruments,  which  are  designed  for  high  accuracy  positioning.  The  GPS  measurement  data  were  collected   using   a   Huawei   P10   device,   41   minutes   and   24   seconds   GPS   observation  time  with  sampling  intervals  of  1  second  using  Geo++  Android  application.  The  GPS  measurements  are  processed  using  standalone  (epoch  by …

Go to article

Point Cloud Pre-Processing And Surface Reconstruction Based On Chord Algorithm Technique, Ali Al-Badairy, Ahmed Al-Duroobi, Maan Tawfiq Aug 2026

Point Cloud Pre-Processing And Surface Reconstruction Based On Chord Algorithm Technique, Ali Al-Badairy, Ahmed Al-Duroobi, Maan Tawfiq

Engineering and Technology Journal

3D laser scanner is one of the modern technologies, which used to obtain the geometric information about the 3D scanned object surface. But, there are some problems that are associated with this technique such as the huge number of obtained points which require high memory to save and the required data processing processes. This paper proposed a data simplification algorithm for point cloud of a scanned object using 3D laser scanner (Matterand Form) in a manner to extract the necessary geometric features, which arerepresented by points for a 3D object. This algorithm based on theinstantaneous calculation of chord height of …

Go to article

Complex Surface Representation And Machining Time Estimation Upon Three Types Of End Mill Cutter, Rasha Marzoog, Ahmed A. Alduroobi Alduroobi, Sawsan Al-Zubaidy Aug 2026

Complex Surface Representation And Machining Time Estimation Upon Three Types Of End Mill Cutter, Rasha Marzoog, Ahmed A. Alduroobi Alduroobi, Sawsan Al-Zubaidy

Engineering and Technology Journal

The accuracy of data transition between CAD and CAM has been playing a great role in the product life cycle, and eventually, the product quality. As products complexity increased, the need to robust technique to data transition increased. On the other hand, Machining simulation facilitates deciding the process parameters. The aim of the present research is divided into two aims: first: building a free form surface and transforming its data accurately from CAD to CAM without any distortion. Second: study the milling process using different end cutters geometry and make a comparison between those in terms of machining time at …

Go to article

Vacuum Effect On The Performance Of Solar Air Collector With Micro-Channel Absorber Plate, Jalal Jalil, Nashwa A.Abdulkadhim Abdulkadhim Aug 2026

Vacuum Effect On The Performance Of Solar Air Collector With Micro-Channel Absorber Plate, Jalal Jalil, Nashwa A.Abdulkadhim Abdulkadhim

Engineering and Technology Journal

In this study, the effect of vacuum with micro-channel techniqueon solar air collector performance is investigated experimentally. Vacuumspace reduces the loss of heat for the absorption plate by conduction andthus improves the solar collector performance. It has been demonstratedthat the solar collector is evacuated to 0.1 bar of pressure for absorber-tocover spacing of 4cm. An absorber plate was manufactured from Aluminummetal with 30 rectangular micro-channels (length 0.9, width 0.004, height0.0008 m) is constructed with measurements facilities of velocity,temperature and differential pressure. The tests are carried out indoor usingsolar simulator. Results showed that the performance of solar collectorincreases with vacuum about …

Go to article

Effect Of Radial Clearance On Stress And Strain Distribution In The Astral Deep Drawing, Waleed Jawad, Ali Ikal Aug 2026

Effect Of Radial Clearance On Stress And Strain Distribution In The Astral Deep Drawing, Waleed Jawad, Ali Ikal

Engineering and Technology Journal

In this paper, an astral die was designed and constructed to produce anastral cup in the deep drawing operation by experimental work and numericalsimulation. The influence of radial clearance on drawing load, cup high, thedistribution of stress, strain and thickness along the side wall, minor and majoraxis were also studied. The deep drawing process was carried out to produce anastral cup with an inner dimension of (41.5mm × 34.69mm), and (30mm) heightdrawn from a blank sheet with a thickness of (0.7) and diameter (80) made of lowcarbon steel. A commercial program (ANSYS18.0) was used to perform thenumerical simulation. Three types …

Go to article

A Hybrid Neural-Fuzzy Network Based Fault Detection And Isolationsystem For Dc Motor Of Robot Manipulator, Arkan Jassim, Abbas Issa, Qusay Jawad Aug 2026

A Hybrid Neural-Fuzzy Network Based Fault Detection And Isolationsystem For Dc Motor Of Robot Manipulator, Arkan Jassim, Abbas Issa, Qusay Jawad

Engineering and Technology Journal

In this paper, the detecting and isolating fault that occurs in (actuator and sensor) in robot manipulator, which is used as a mathematical model were proposed for fault detection, where the neural network was used to detect the fault. The neural network was trained on the data set obtained from the Input/output on the (DC motor).The output of the sensor or actuator was compared with the output of the model (neural network) after that the residual signal is used to detect the fault. The fuzzy logic circuit was used for fault isolation that is depending on the residual signal from …

Go to article

Enhanced Solution Of Inverse Kinematics For Redundant Robot Manipulator Using Pso, Hind Khaleel Aug 2026

Enhanced Solution Of Inverse Kinematics For Redundant Robot Manipulator Using Pso, Hind Khaleel

Engineering and Technology Journal

Kinematics of the robot is divided into two parts: the forwardkinematics, which evaluates the end-effector’s position from joint angles, and theinverse kinematics, which demonstrates the joint angles from the end-effector'sposition. The solution of the inverse kinematics problem is too difficult andcomplicated for the redundant robot arm manipulator. A Particle SwarmOptimization (PSO) algorithm is an effective method to solve global optimizationproblems. This paper presents the solution of inverse kinematics problem of athree-link redundant manipulator robot arm using PSO without using the inversekinematics equations. The circle, square and triangle generated trajectories usingPSO are enhanced as compared with the trajectories of other works. …

Go to article

Investigation Of External And Internal Inversion For Aluminum Tube With Various Die Parameters Effect, Basim Fadhil, Ava Kamal Aug 2026

Investigation Of External And Internal Inversion For Aluminum Tube With Various Die Parameters Effect, Basim Fadhil, Ava Kamal

Engineering and Technology Journal

Finite element modeling has been conducted to investigate theeffect of die radius fillet, tube wall thickness, and friction coefficient on bothexternal and internal inversion forthealuminum tube. A 3D model was usedto build the contact pair for the aluminum tube and the steeldie. Due to theaxial symmetry, a 45osector for the contact pair has been chosen. It has beenfound that there is an important role for those parameters to govern theinversion process and the mode of deformation beside the value of theapplied force. No local buckling was seen in the external inversion incontrast with internal inversion. A good correlation for current …

Go to article

A Group Authentication Protocol On Multilayer Structure For Privacy-Preserving Iot Environment, Maytham Azhar, Amin Seno Aug 2026

A Group Authentication Protocol On Multilayer Structure For Privacy-Preserving Iot Environment, Maytham Azhar, Amin Seno

Engineering and Technology Journal

In the Internet of Things (IoT) systems, large amounts of data are accumulated from anywhere at any time, which may attack individuals' privacy, especially when systems are utilized in medical and everyday environments. With the promise of IoT's proactive systems, the integration of smart things into standard Internet creates several security challenges, because most Internet technologies, communication protocols and sensors are not designed to support IoT. Recent research studies have shown that launching security / privacy attacks against IoT active systems, in particular, Wearable Medical Sensor (WMS) systems, may lead to catastrophic situations and life-threatening conditions. Therefore, security threats and …

Go to article

Removal Oil From Produced Water By Using Adsorption Method With Adsorbent A Papyrus Reeds, Firas Al-Zuhairi, Rana Azeez, Suhair Mahdi, Wafaa Kadhim Kadhim, Muna Al-Naamee Aug 2026

Removal Oil From Produced Water By Using Adsorption Method With Adsorbent A Papyrus Reeds, Firas Al-Zuhairi, Rana Azeez, Suhair Mahdi, Wafaa Kadhim Kadhim, Muna Al-Naamee

Engineering and Technology Journal

A papyrus reed, as a type of unusable farming waste, was used as akind of low-cost biosorbent for the elimination a crude oil from produced waterthat was produced in an Al-Ahdab field, Iraq, in a batch stirred operationmode. Fourier transform infrared spectroscopy (FTIR) and scanning electronmicroscope (SEM) were used to characterize the biosorbent before and afteradsorption. Batch tests were employed as a function of the contact time,adsorbent dose, and the pH of the solution. The experimental results show atincreases the amount adsorbent dosage, pH and contact times, the removalefficiencies were increases and optimum condition was obtained at pH valueequal to …

Go to article

Rules For Managing Methods Of Implementation And Evaluation Of Graduation Projects In Engineering Departments, Fatimah Naser, Maryam Naser Aug 2026

Rules For Managing Methods Of Implementation And Evaluation Of Graduation Projects In Engineering Departments, Fatimah Naser, Maryam Naser

Engineering and Technology Journal

Graduation projects are the final product of what university students have acquired from the sciences and knowledge during their academic period of study during the academic years, which range in most Iraqi universities between 4 to 5 years in engineering colleges. In the last year during which the student to implement the engineering graduation project, which begins by choosing the subject or problem that will be dealt with as a research title and ends with the development of all stages of implementation. And the importance of graduation projects for students of engineering departments to study the bachelor's degree and the …

Go to article

Measurement Of Student Outcomes Attainment For Abet Accreditation In Electromechanical Engineering Department In Uot, Jalal Jalil Aug 2026

Measurement Of Student Outcomes Attainment For Abet Accreditation In Electromechanical Engineering Department In Uot, Jalal Jalil

Engineering and Technology Journal

Student outcomes attainment represents the core of the ABET accreditation. In this paper, a details of the four years’ work in Energy and Renewable Energy Program in Electromechanical Engineering Department in University of Technology was demonstrated, concentrating on the process of student outcomes attainment measurement. The attainment of student outcomes represents a challenge in all programs in Iraqi Universities. The process monitored by ABET Foundation expertise through IREX and they approved that the process reached right route although the degree of attainment needs more work in the coming years to reach accreditation level.

Go to article

Code Of Conduct Of Final Year Projects In Engineering Disciplines, Fawzi Al-Naima Aug 2026

Code Of Conduct Of Final Year Projects In Engineering Disciplines, Fawzi Al-Naima

Engineering and Technology Journal

The importance of the management and implementation of graduation projects lies in the fact that this activity constitutes one of the main pillars of the undergraduate academic curricula in most scientific or literary disciplines. In engineering studies, for example, the weight of the graduation project within the curriculum is estimated at 25% for the year of graduation and about 8% of the total weight of the first university degree in most universities in the developed countries. In this context, this paper suggests specific steps for conducting this work and the allocation of responsibilities in the management of this scientific activity. …

Go to article

Study The Effect Of Apply The Problem Based Learning In Engineering Education, Raed Hwayyin, Azhar Ameed Aug 2026

Study The Effect Of Apply The Problem Based Learning In Engineering Education, Raed Hwayyin, Azhar Ameed

Engineering and Technology Journal

The study examined the effect of application of the problem-based learning method of teaching engineering students in the Department of Petroleum Technology compared to traditional teaching methods (lecture). The problem-based learning method involved a number of assessments and exams that students individually and collectively performed. The study investigates the first class students of petroleum technology department of two subjects which are the calculus and engineering practice subjects. The study is use the statistical calculations to compare between applying the problem based learning and tradition method “lecture method” in engineering education, and taking into consideration the individual differences between students to …

Go to article

Different Levels Of Engineering Education (Ee): Needs And Applications, Ameen Al-Juboori, Aws Al-Akam, Amir Saud Aug 2026

Different Levels Of Engineering Education (Ee): Needs And Applications, Ameen Al-Juboori, Aws Al-Akam, Amir Saud

Engineering and Technology Journal

Engineering education is often described as being constructivist, suggesting that learning involves constructing an understanding of several components. There is a commonly used series of levels of learning. It is most frequently presented in terms of six levels of understanding. Every learner has to follow these levels. However, the impact of these levels may vary from one learner to another. This paper study the impact of one different level of Engineering Education (EE) on the different background of learners. Furthermore, it investigates the problems that face EE in Iraq and offers several solutions. This work is the first step to …

Go to article

Assessing The Level Of Reflective Thinking In Engineering Teachers During The Process Of Research Action, Raudhah Ali, Abdulhadi Al-Saady, Najah Al Maimuri Aug 2026

Assessing The Level Of Reflective Thinking In Engineering Teachers During The Process Of Research Action, Raudhah Ali, Abdulhadi Al-Saady, Najah Al Maimuri

Engineering and Technology Journal

A hydrogeologic study has been adopted to conceptualize the concepts of groundwater levels lowering in swamped area of Tyass, middle of Iraq. 2D dimensional groundwater model and, mitigation model have been used to mitigate the aquifer against high salinity and chemical pollutants by the mitigation theory of heterogeneous subsurface media which basically depends upon physical and mathematical derivation, evaluation of chemical pollutants and total dissolved salts (TDS) of subsurface water before and after mitigation process. The water table level was lowered up to 2.43m at the center of a pumping well of abstraction discharge (400m3/day) obtained after 2755days in steady …

Go to article

Mapping Lclu Using Python Scripting, Oday Jasim, Khalid Hasoon, Noor Sadiqe Aug 2026

Mapping Lclu Using Python Scripting, Oday Jasim, Khalid Hasoon, Noor Sadiqe

Engineering and Technology Journal

Land cover land use changes constantly with the time at local, regional, and global scales, therefore, remote sensing provides wide, and broad information for quantifying the location, extent, and variability of change; the reason and processes of change; and the responses to and consequences of change. And considering to the importance of mapping of (LCLU). For that reason this study will focus on the problems arising from the traditional classification (LCLU) that based on spatial resolution only which leads to prediction a thematic map with noisy classes, and using a new method that depend on spectral and spatial resolution to …

Go to article

E-Learning Applications In Engineering And The Project-Based Learning Vs Problem-Based Learning Styles: A Critical & Comparative Study, Hatim Abood Aug 2026

E-Learning Applications In Engineering And The Project-Based Learning Vs Problem-Based Learning Styles: A Critical & Comparative Study, Hatim Abood

Engineering and Technology Journal

The paper aims to critically review the learning styles and teaching methods of engineering curricula and to compare it with the requirements of engineering profession. Present engineers need to response effectively to the increasingly complex systems. The engineer has to deal with vector and scaler quantities, complex numbers, imaginary parts, electromagnetic fields, and complex constructions are designed and implemented in 3-Dimensions environment. This should be reflected in engineering education styles, where lecturers try to convey many aspects of complex systems. The purpose of engineering education is that to graduate engineers who can design and solve technical problems, and that design …

Go to article

Hydrogeologic Sustainability And Mitigation Of Shallow Groundwater Against High Saline And Chemical Pollutants, Najah Al Maimuri, Arkan Ali, Abdulhadi Al-Sa’Adi, Mohammed Abed Abed Aug 2026

Hydrogeologic Sustainability And Mitigation Of Shallow Groundwater Against High Saline And Chemical Pollutants, Najah Al Maimuri, Arkan Ali, Abdulhadi Al-Sa’Adi, Mohammed Abed Abed

Engineering and Technology Journal

A hydrogeologic study has been adopted to conceptualize the concepts of groundwater levels lowering in swamped area of Tyass, middle of Iraq. 2D dimensional groundwater model and, mitigation model has been used to mitigate the aquifer against high salinity and chemical pollutants by the mitigation theory of heterogeneous subsurface media, which depends upon physical and mathematical derivation, evaluation of chemical pollutants and total dissolved salts (TDS) of subsurface water before and after mitigation process. The water table level was lowered up to 2.43m at the center of a pumping well of abstraction discharge (400m3/day) obtained after 2755days in steady state. …

Go to article

Design Of N-Bit Adder Without Applying Binary To Quaternary Conversion, Walaa Khalaf, Dhafer Zaghar, Kadhum Al-Majdi Aug 2026

Design Of N-Bit Adder Without Applying Binary To Quaternary Conversion, Walaa Khalaf, Dhafer Zaghar, Kadhum Al-Majdi

Engineering and Technology Journal

Microprocessor has been considered as most important part in ICs manufacturing and making progress since more than 50 years, so increasing microprocessor speed is paid attention in all technologies. ALU is known as the slowest part in microprocessor because of the ripple carry, nowadays microprocessor uses 8-uints as pipeline, each one has 8-bits for implementing 64-bit, working in this form has been captured the microprocessor development and limited its speed for all its computations. Parallel processing and high speed ICs always trying to increase this speed but unfortunately it remains limited. The contemporary solution for increasing microprocessors speed is the …

Go to article

Optimal Location And Parameter Setting Of Statcom Device Based Pso For Iraqi Grid Voltage Profile Enhancement And Power Losses Minimizing, Rashid Al-Rubayi, Mohammed Eesee Aug 2026

Optimal Location And Parameter Setting Of Statcom Device Based Pso For Iraqi Grid Voltage Profile Enhancement And Power Losses Minimizing, Rashid Al-Rubayi, Mohammed Eesee

Engineering and Technology Journal

The main goal of this work is to enhance the Voltage stability by using optimum location and parameters setting of STATCOM device. The parameters are the magnitude of the output voltage ������ and the angle ������, these parameters are taken to control the device performance. The simulation results have been done by using power flow program solution by Newton-Raphson method (Matlab program / M-file) with Particle Swarm Optimization (PSO) technique, for power losses minimizing and improving voltage profile. Two systems have been implemented:- IEEE 5-bus test system and Iraqi (400 kV) National super Grid System 27-bus. The MATLAB programs are …

Go to article

Dynamic Study Of Carbon Dioxide Absorption Using Promoted Absorbent In Bubble Column Reactor, Safa Al-Naimi, Farah Jasim, Ahmed Kokaz Aug 2026

Dynamic Study Of Carbon Dioxide Absorption Using Promoted Absorbent In Bubble Column Reactor, Safa Al-Naimi, Farah Jasim, Ahmed Kokaz

Engineering and Technology Journal

The most common process to remove carbon dioxide from natural gas and the flue gasses is absorption into suitable solvents. Absorption of carbon dioxide are studied experimentally in this work using bubble column reactor (glass cylindrical (QVF) of 7.5 cm i.d. × 140 cm height), where different types of absorbent (30%MEA, 30%K2CO3), promoter types (organic(piperazine)and inorganic(amino acids)) and concentrations were examined over a wide range of gas flow rate cover homogeneous to transition flow regime at ambient temperature and atmospheric pressure. The results showed that the dissolved gas undergoes a pseudo-first order reaction, and the optimum superficial velocity of gas …

Go to article

Thermodynamic And Kinetic Investigation Of Desalination By Refrigerant Clathrate Hydrate Formation, Shurooq Al-Hemeri, Riyadh Al-Mukhtar, Lina Mahmood Aug 2026

Thermodynamic And Kinetic Investigation Of Desalination By Refrigerant Clathrate Hydrate Formation, Shurooq Al-Hemeri, Riyadh Al-Mukhtar, Lina Mahmood

Engineering and Technology Journal

Gas hydrate is a crystalline solid compound form of water with hydrophobic gas at certain conditions (pressure and temperature). The hydrogen bond in water molecules constructs a framework as a host that entraps gas molecules (gust). Gas hydrate can be applied to many industries such as gas separation, cool storage, food concentration and desalination. Hydrate route looks a promising alternative technology compared to the conventional process, by utilizing a proper gas host, which can be held within water cavities composed by hydrogen-bonded water molecules. In this study the selected host gas was Refrigerant R134a, the work consists of an experimental …

Go to article

First Prev Next Last