Digital Commons Network^™

Impact Of Configuration Variations On Small Modular Reactor Core Performance, William Kirby Compton

Masters Theses

"One of the most promising new reactor designs is the Small Modular Reactor (SMR). These reactors, which operate under 300 MWe, will help bring cheap and safe nuclear energy to remote and centralized locations alike. Their ease of construction, advanced passive safety features, and cost effectiveness make these reactors an intriguing option for the near future.

In the work presented here, a neutronics analysis of the Westinghouse SMR was performed. Westinghouse's SMR design is a scaled down version of their AP1000 plant and will produce about 225 MWe of power. Though the parameters of the reactor core will be modeled …

Neutronic Analysis Of Light Water Small Modular Reactor With Flexible Fuel Configurations, Brendan Dsouza

Masters Theses

"The study was focused on the analysis of light water Small Modular Reactor (SMR) with flexible fuel configurations. The core design, based on the Westinghouse UO₂ SMR with less than 5% enrichment was developed using the Monte Carlo N-Particle (MCNP) code. Neutronics analyses of a reference core with UO₂ fuel was performed to characterize parameters such as the radial neutron flux profile, the maximum to average flux ratio, the reactivity coefficient and critical boron concentration at beginning of life; which confirmed good performance in comparison to a standard UO₂ based pressurized water reactor.

Using this uranium oxide …

Evaluation Of Preformed Particle Gel Treatment Using Homogeneous And Heterogeneous Models, Hilary Ogochukwu Elue

Masters Theses

"This research investigates the effects of preformed particle gel (PPG) in remedying the problems of excess water production and low oil recovery of heterogeneous reservoirs by placing the PPG in the high-permeability layer, thus diverting displacing brine to the unswept low permeability layer. This investigation was completed with three tasks.

The first task was to evaluate the PPG swelling kinetics and strength as a function of concentration of brine. The result of this task indicate that PPG prepared with low concentration of brine swells more, becomes weaker, more deformable than PPG prepared with high concentration of brine.

The second task …

Computer Aided Detection Of Oral Lesions On Ct Images, Shaikat Mahmood Galib

Masters Theses

"Oral lesions are important findings on computed tomography images. They are difficult to detect on CT images because of low contrast, arbitrary orientation of objects, complicated topology and lack of clear lines indicating lesions. In this thesis, a fully automatic method to detect oral lesions from dental CT images is proposed to identify (1) Closed boundary lesions and (2) Bone deformation lesions. Two algorithms were developed to recognize these two types of lesions, which cover most of the lesion types that can be found on CT images. The results were validated using a dataset of 52 patients. Using non training …

Comprehensive Benefits Of Green Roofs, Madison R. Gibler

Masters Theses

"Green infrastructure uses vegetation, soils, and natural processes to manage water and create healthier urban environments, providing traditional roof services and alternative stormwater management technologies. Other benefits and impacts are not yet fully understood or valued. Research conducted assesses specific stormwater benefits of green roofs, providing information on nutrient leaching from media; and analyzes potential energy benefits through side-by-side comparisons of full-scale white, traditional black rubber, and green roofs in the mid-continent Missouri climate. Roofing media selection impacted leaching of nutrients, suspended solids, and organic carbon from the tested green roof media. Thermal properties were investigated at the building level, …

Pipeline Leak Detection, Marcia Golmohamadi

Masters Theses

"In the present research two techniques are applied for leak detection in pipelines. The first method is a hardware-based technique which uses ultrasonic wave's emission for pipeline inspection. Ultrasonic waves are propagated in the pipe walls and reflected signal from leakage will be used for pipe analysis. Several Pipes with various dimensions and characteristics are modeled by finite element method using ANSYS. Second order longitudinal modes of ultrasonic waves are emitted in their walls. For this purpose, excited frequency is calculated such that it excites the second order longitude mode. In order to investigate the behavior of emitted wave in …

Initial Fuel Possibilities For The Thorium Molten Salt Reactor, Dustin Gage Green

Masters Theses

"The Generation IV International Forum placed six reactors as priority for research and development to compensate for the world's increasing energy demands. Among the six were Molten Salt Reactors (MSRs). These reactors utilize the Th/²³³U fuel cycle using molten fluoride or chloride salts as coolants. MSRs also have the possibility to use other fissile fuels especially with the first fleet of reactors given the low amount of Uranium-233 available commercially.

With the possibility of diverting from using ²³³U initially, the research presented here will benchmark ²³³U as a main fuel for MSRs using the Thorium Molten …

Characterizing The Influence Of Carbon On The Flowrate And Disinfection Efficacy Of Household Ceramic Water Filters, Jessie Yvonne Hahn

Masters Theses

"Drinking water contamination is a major cause of disease in developing countries. Point of Use (POU) water treatment technologies generally have low initial cost and allow rapid availability of improved water. Ceramic pot filters (CPFs) are a POU water source treatment technology which filter water by gravity through a porous ceramic media. Some filters in use contain carbon remnants left from the fugitive pore former as a dark carbon core. Using disk-shaped experimental ceramic filters produced in the lab to have varying levels of carbon, the percent carbon present was measured and a visual analysis method was developed to determine …

Model Predictive Current Control Of Switched Reluctance Motor With Inductance Auto-Calibration, Xin Li

Masters Theses

"The thesis is composed of three papers, which investigate the application of Model Predictive Controller (MPC) for current control of Switched Reluctance Motor (SRM). Since the conventional hysteresis current control method is not suitable for high power SRM drive system with low inductance and limited switching frequency, MPC is a promising alternative approach for this application. The proposed MPC can cope with the measurement noise as well as uncertainties within the machine inductance profile. In the first paper, a MPC current control method for Double-Stator Switched Reluctance Motor (DSSRM) drives is presented. A direct adaptive estimator is incorporated to follow …

A Study Into Improving Transformer Loading Capability Beyond Nameplate Rating, Aakanksha Pasricha

Masters Theses

"Utilities are becoming increasingly interested in the prospect of overloading the transformers beyond the nameplate rating to meet the increased demand for power as it may be more economically viable than installing a new transformer. The safety of the transformer has to be ensured while overloading it and hence there is a maximum loading beyond which the transformer should not be overloaded. A study has been performed on 38 transformer units and the factors that limit their overloading capability have been analyzed. Ancillary equipment ratings were found to be the most prominent limiting factor. Several case studies and evaluation results …

Emi Analysis Of Dvi Link Connectors, Abhishek Patnaik

Masters Theses

"EMI problems are not uncommon in high speed communication systems. As the system clock frequencies increases, so does the challenges in controlling the EMI in such systems. A connector is a very important part of a high speed communication system. Electromagnetic interference (EMI) is found to be tightly correlated to mode conversion: from differential-mode (DM) signals to common-mode (CM) currents and further to antenna-mode (AM) currents on the outside of cables or enclosures. Moreover, in such high speed systems, coupling to an adjacent cable-connector system is not uncommon. It is essential to understand and quantify this coupling path in order …

Laser Surface And Sub-Surface Repair During Metal Additive Manufacturing, Prudvi Teja Ravi

Masters Theses

"This study examines the use of laser surface treatment to repair surface and subsurface defects. Numerical analysis was performed on laser surface melting using Gaussian heat distribution equations to analyze the depth of the melt pool created by the phenomena. Concurrently, a process map was developed with a planned set of experiments by varying the ranges of laser power and travel speed to determine the dimensions of the melt pool across the gamut. The data generated from both the process studies and the numerical analysis was then used to determine the ideal operating ranges of the process parameters to repair …

Spatial And Temporal Modulation Of Heat Source Using Light Modulator For Advanced Thermography, Arvindvivek Ravichandran

Masters Theses

"Thermography is a Non-Destructive Testing (NDT) method that has found increasing use in industry and research. It has the advantages of being non-contact and be able to interrogate a large surface simultaneously. Active thermography using flash lamps as heat source has been demonstrated for identifying blind holes and delamination in composites. Despite these advancements, active thermographic approach fails to defects like cracks. Under uniform illumination heat flow is predominantly 1D and can easily circumvent a narrow feature. This can be overcome by using a focused light/laser source onto the surface to impose a 3D heat flux. The disadvantage is that …

Signal Integrity Analysis Of A Low Cost Pcb To Pcb System, Kancy Robison

Masters Theses

"This report presents the analysis of a low cost PCB to PCB cable and connector system focusing on its data rate limitations and optimizing transmitter and receiver operations. Economic factors have an ineluctable presence in digital hardware engineering and, as data rates are continually pushed to new bounds, finding cheaper alternatives in hardware while maintaining performance standards becomes more relevant. This study will show the measurement and simulation of a low cost digital system which includes a PCB board, connector, and a multi-pin flex cable (ribbon cable). These S-parameter and TDR measurements/simulations are used to gain an intuition for the …

A New Technique For Modeling The Geomorphology Of A Slow Moving, Soft-Slope Landslide Using Terrestrial Lidar, Nathan Bradley Rohrbaugh

Masters Theses

"Soft slope movement is a big problem whether it involves an engineered slope, one that is near infrastructure, or both. Active landslides that fail slowly sometimes allow ample time to affect remedial works. In order to plan effective remedial works, there needs to be a model of the entire geometry of the slide. This thesis describes a new approach to evaluate the morphology of slope geometry using Light Detection and Ranging (LiDAR) data obtained from simple targets strategically positioned on a slide body. The data was gathered in three-month intervals over a period of one year to allow enough time …

Energy Disaggregation In Nialm Using Hidden Markov Models, Anusha Sankara

Masters Theses

"This work presents an appliance disaggregation technique to handle the fundamental goal of the Non-Intrusive Appliance Load Monitoring (NIALM) problem i.e., a simple breakdown of an appliance level energy consumption of a house. It also presents the modeling of individual appliances as load models using hidden Markov models and combined appliances as a single load model using factorial hidden Markov models. Granularity of the power readings of the disaggregated appliances matches with that of the readings collected at the service entrance. Accuracy of the proposed algorithm is evaluated using publicly released Tracebase data sets and UK-DALE data sets at various …

The Effects Of Physical Flash Hole Deviations On Factory-Grade Rifle Ammunition, Nicolaas Martin Schrier

Masters Theses

"The objective of this research is to determine the effect of dimensional and positional changes of the primer flash hole on the performance of factory-grade rifle ammunition. The studied variables were flash hole diameter, offset from center, and orientation of the offset in the primer pocket. Cartridge performance was quantified by measuring muzzle velocity, chamber pressure, and target grouping size (precision).

Five different flash hole diameters were tested for both the Remington .223 and Winchester .308 calibers: 1.4mm, 2.0mm (the Fiocchi standard), 2.4mm, 2.8mm, and 3.0mm. Each diameter was tested at three offsets: centered (no offset), 0.5mm from center, and …

Fuzzy Adaptive Resonance Theory: Applications And Extensions, Clayton Parker Smith

Masters Theses

"Adaptive Resonance Theory, ART, is a powerful clustering tool for learning arbitrary patterns in a self-organizing manner. In this research, two papers are presented that examine the extensibility and applications of ART. The first paper examines a means to boost ART performance by assigning each cluster a vigilance value, instead of a single value for the whole ART module. A Particle Swarm Optimization technique is used to search for desirable vigilance values. In the second paper, it is shown how ART, and clustering in general, can be a useful tool in preprocessing time series data. Clustering quantization attempts to meaningfully …

3d Numerical Modelling Of Micropiles Interaction With Soil & Rock, Audai Kamal Theinat

Masters Theses

"A 5-span bridge along the Foothills Parkway of the Great Smoky Mountains, TN, was recently completed. Two out of the four piers were instrumented to measure the load transfer in the foundations. The foundations consisted of twenty 10-inch micropiles under the pile cap for each pier. Strain gages were installed and monitored at the different stages of construction. The objective of this research is to examine the interaction between the ground and micropiles using the field data performance and numerical modelling. The 3D computer model consists of the micropile foundation within the steep rock bedding planes and overburden soils. The …

Co₂ Miscible Flooding Application And Screening Criteria, Mingfei Yin

Masters Theses

"Field experience has shown that CO₂ miscible flooding is an effective method to improve oil recovery, but only with proper reservoir candidate selection and optimal project design. This paper discusses both CO₂ miscible and immiscible flooding mechanisms and offers some guidelines for flooding operations. New developments in MMP determination are also introduced.

This research is based on a summary of field data from 134 CO₂ projects in the U.S. Several numerical methods have been applied for data cleaning. After cleaning, data from 128 projects have been analyzed and correlated. Carbonate reservoirs and sandstone reservoirs are the two …

Rote-Lcs Learning Classifier System For Classification And Prediction, Benjamin Daniels

Masters Theses

"Machine Learning (ML) involves the use of computer algorithms to solve for approximate solutions to problems with large, complex search spaces. Such problems have no known solution method, and search spaces too large to allow brute force search to be feasible. Evolutionary algorithms (EA) are a subset of machine learning algorithms which simulate fundamental concepts of evolution. EAs do not guarantee a perfect solution, but rather facilitate convergence to a solution of which the accuracy depends on a given EA's learning architecture and the dynamics of the problem.

Learning classifier systems (LCS) are algorithms comprising a subset of EAs. The …

A Novel Entropy Production Based Full-Chip Tsv Fatigue Analysis, Tianchen Wang

Masters Theses

"Through-silicon vias (TSVs) are subject to thermal fatigue due to stress over time, no matter how small the stress is. Existing works on TSV fatigue all rely on measurement-based parameters to estimate the lifetime, and cannot consider detailed thermal profiles. In this paper, we propose a new method for TSV fatigue prediction using entropy production during thermal cycles. By combining thermodynamics and mechanics laws, the fatigue process can be quantitatively evaluated with detailed thermal profiles. Experimental results show that interestingly, the landing pad possesses the most easy-to-fail region, which generates up to 50% more entropy compared with the TSV body. …

Optimal Techno-Economic Sizing Of Wind/Solar/Battery Hybrid Microgrid System Using The Forever Power Method, Sami Hamed Alalwani

Masters Theses

"Advancement in power electronics, energy storage, control, and renewable energy sources has led to the use of integrated renewable energy sources in islanded microgrids (MG). Also, the uses of integrated renewable energy sources have become more technically applicable, more economically feasible, and more environmentally friendly than conventional sources. As a result, electrification of rural villages using renewable energy technologies has started to become widely adopted around the world. Since generating power from renewable energy sources is highly intermittent and difficult to predict, the use of proper energy storage technology is important to eliminate mismatches between the load demand and generation. …

A Valuation Model For Two-Stage Contract Negotiations Over Multiple Interdependent Issues, Nnaemeka U. Amaeshi

Masters Theses

"Most real-world negotiation scenarios involve multiple interdependent issues over which the negotiating parties will seek an agreement. Simultaneous negotiation over multiple interdependent issues is an especially challenging problem because utility functions of negotiating agents are typically nonlinear and difficult to analyze. Also, negotiations often happen under circumstances of incomplete information, where either party has either little or inaccurate information about the preferences or utilities of the other party. Consequently, negotiations may go over multiple rounds until a mutually acceptable agreement is reached. The objective of this research is to create a quantitative model of decision-making that helps one negotiating party …

Cappack Devices For Enhanced Qnmr Measurements In 1H Nmr Spectroscopy, Lingyu Chi

Masters Theses

"Quantitative NMR analyses can be improved by adding well-defined external references for measuring sample properties on absolute scales. Special Capillary-tube Package (CapPack) devices were invented that provide in situ information (e.g., temperature, pH, pressure, integration, chemical shift, lock, etc.) about a sample with spectral imprimaturs. A new microscale glass-sealing technique produced CapPack devices that can survive high temperatures and pressures in harsh environments. Two CapPack devices are discussed: (1) Gradient CapPack-- a device for examining the irradiation bandwidth of solvent-suppression pulse sequences; (2) T₁ CapPack - a device for examining the T₁ robustness of solvent-suppression pulse sequences. A …

Thermodynamic And Chemical Kinetic Coupled Modeling For The Determination Of Cyclic Combustion Phasing In Hcci Engines, Krishawn Michele Goodwin

Masters Theses

"Homogeneous charge compression ignition (HCCI) is a low temperature combustion mode that contains great potential for decreasing emissions while increasing efficiency in internal combustion engines. The limitation is in that it is inherently difficult to control based on the lack of an external combustion trigger. This thesis outlines the potential of using the combustion residual species of carbon monoxide as a method of controlling the location of combustion by using data from a computer model. The model is a nonlinear five-state thermodynamic model that is coupled with a skeletal chemical kinetic model for PRF96. The model computes the amount of …

Optimum Acquisition And Processing Parameters For Multichannel Analysis Of Surface Waves Using 3d Electrical Resistivity Tomography As Control, Uchenna Chibuzo Nwafor

Masters Theses

"Multichannel Analysis of Surface Waves (MASW) and Electrical Resistivity Tomography (ERT) data were acquired in the Newburg, Missouri with the goal of determining optimum MASW acquisition parameters. Users of the MASW tool generally state that greater geophone intervals and greater shot-to-receiver offsets provide for more accurate results. The objective was to determine if this "rule of thumb" applies in karst terrain.

ERT data were acquired along four traverses with eighty-four (84) electrodes at five feet spacing with SuperSting R8 Resistivity System using dipole- dipole array. The data were processed using Earth Imager to generate 2-D resistivity inversion and thereafter, Voxler …

Freeze-Form Extrusion Fabrication Of Boron Carbide, Aaron Scott Thornton

Masters Theses

"Boron carbide is a safe, alternative to beryllium as a material for aerospace structures since it is also light-weight and exhibits high strength. This paper discusses a study of the Freeze-form Extrusion Fabrication (FEF) process to fabricate parts from boron carbide. Process parameters and hardware were modified to fabricate boron carbide specimens free of printed defects. Four-point bending tests were performed to measure the flexural strength of fabricated specimens. Observations of the presence of voids caused by ice crystals in fabricated parts led to further development and characterization of the boron carbide paste used with the FEF process. Additives were …

Common Path Pessimism Removal In Static Timing Analysis, Chunyu Wang

Masters Theses

"Static timing analysis is a key process to guarantee timing closure for modern IC designs. However, additional pessimism can significantly increase the difficulty to achieve timing closure. Common path pessimism removal (CPPR) is a prevalent step to achieve accurate timing signoff. To speed up the existing exhaustive exploration on all paths in a design, this thesis introduces a fast multi-threading timing analysis for removing common path pessimism based on block-based static timing analysis. Experimental results show that the proposed method has faster runtime in removing excess pessimism from clock paths."--Abstract, page iii.

Design And Implementation Of Low Complexity Wake-Up Receiver For Underwater Acoustic Sensor Networks, Ming Yue

Masters Theses

"This thesis designs a low-complexity dual Pseudorandom Noise (PN) scheme for identity (ID) detection and coarse frame synchronization. The two PN sequences for a node are identical and are separated by a specified length of gap which serves as the ID of different sensor nodes. The dual PN sequences are short in length but are capable of combating severe underwater acoustic (UWA) multipath fading channels that exhibit time varying impulse responses up to 100 taps. The receiver ID detection is implemented on a microcontroller MSP430F5529 by calculating the correlation between the two segments of the PN sequence with the specified …