Digital Commons Network^™

2015 Fall Commencement, Georgia Southern University

Commencement Programs

No abstract provided.

Gurc Program [2015], Gurc

Georgia Undergraduate Research Conference (Archived)

NA

Evaluation Of Rock Fall Hazards Using Lidar Technology, Norbert H. Maerz, Travis Kassebaum, Kenneth J. Boyko, James Otoo

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Lidar (light detection and ranging) is a relatively new technology that is being used in many aspects of geology and engineering, including researching the potential for rock falls on highway rock cuts. At Missouri University of Science and Technology, we are developing methods for measuring joint orientations remotely and quantifying the raveling process. Measuring joint orientations remotely along highways is safer, more accurate and can result in larger and more accurate data sets, including measurements from otherwise inaccessible areas. Measuring the nature of rock raveling will provide the data needed to begin the process of modeling the rock raveling process. …

Georgia Southern Magazine, Georgia Southern University

Georgia Southern Magazine

• Eagles in Love
• Taste of Excitement
• "I Just Want to be a Good Guy"
• Outstanding Service
• Another Leap Forward

Cover And Contents

Turkish Journal of Physics

No abstract provided.

Cover And Contents

Turkish Journal of Physics

No abstract provided.

Hybrid Manufacturing Process Of SicF/Sic Composite Using Preceramic Polymer, Robert Raymond Meinders

Masters Theses

"Continuous fiber-reinforced silicon carbide (SiC_f/SiC) ceramic composites have been increasingly used due to their high temperature strength and graceful failure mechanisms. A disadvantage is the high cost and lengthy production processes that are required to develop these materials. Polymer infiltration and pyrolysis (PIP) is one of the most attractive fabrication processes for composites due to shape flexibility, mass production and relatively low cost; however, the quality of material obtained by this method has been considered insufficient due to the microstructure defects of the material obtained. This study investigated a hybrid of multiple polymer manufacturing processes to maximize quality …

Estimation Of Tip-Sample Force In Tapping Mode Atomic Force Microscopy Using Neural-Network And Repetitive Control Approaches, Alireza Toghraee

Masters Theses

"Atomic Force Microscopy is one of the most powerful tools for imaging, measuring and manipulating materials at nanometer scale. Among different modes of AFM, tapping mode, in which the oscillating tip touches the sample periodically, is most common mode. During the tip approach and retract, the tip interacts with sample and experiences different force regimes. This tip-sample interaction force contains information about the sample topology, material properties and tip geometry. However, quantitative measurement of the time-varying tip-sample interaction forcing function is challenging in the tapping mode because of the combined dynamic complexities of the cantilever and nonlinear complexity of the …

Mr4rf: Mem-Device With Impedance And Their Usage With Impedance Matching Networks For Passive Rfid Tags In The Uhf, George H. Harris

Masters Theses

"The passive RFID tag in the UHF has been employed in several different applications including, tracking, logistics, and as a sensing platform for the Internet of things (IoT). The tag is ideal for this industry due to its unique design. It harvests all of its energy from the environment, and is small, cheap, and requires little to no maintenance. However, there are two major issues limiting the potential of the passive RFID systems: the limited power harvested by the tag, and the high susceptibility to interference and coupling. In particular, dynamic environments render the traditionally fixed, RF impedance matching network …

Adaptable Ring, Bayes Theorem And Dual Gradient Analysis: An Approach To Automatic Shape Detection, Skin Lesion Segmentation And Focus Detection Respectively For Medical Image Analysis, Kanakam T. Maddala

Masters Theses

“Vision-based applications are increasing with the increase in technology and are making a huge impact in this global civilization. A vision-based measurement approach for pill shape detection was developed for medical pill identification, a focus detection method was developed for digital dermoscopy, and a machine learning approach was used for automatic lesion segmentation, which assists in automatic melanoma diagnosis. Rapid and accurate pill identification is needed by medical and law enforcement personnel during emergencies. But, one of the main parameters in pill identification is the shape of the pill. An Adaptable-Ring approach describes a novel technique to accurately detect the …

Experimental Study Of Crude Oil Emulsion Stability By Surfactants And Nanoparticles, Zainab Alabdulmohsen

Masters Theses

"Surfactants and nanoparticles are materials being widely used for enhanced oil recovery (EOR). Surfactants are mainly used to reduce the interfacial tension between oil and water which could form a stable film of emulsion between these two immiscible fluids. Also, nanotechnology is a potential candidate to offer another solution to improve oil recovery. Nanoparticles can form a solid layer at the droplet's interface and stand as resistant stabilizer under harsh reservoir conditions.

This research investigates whether the combination of surfactants and nanoparticles can provide a more stable emulsion than surfactants only. Two parts of experimental study have been done in …

Evaluation Of Millimeter-Sized Preformed Particle Gel For Conformance Control Treatments Using Simple Models, Ali Abdulmohsen Al Brahim

Masters Theses

Millimeter-sized preformed particle gels (PPGs) have been successfully used to tackle the high-permeable zones, fractures and channels in mature oilfields for conformance control improvement. PPGs can significantly reduce the permeability of abnormal fractures and divert injected water to the low permeable zones where hydrocarbon was not swept by previous water flooding. Due to the irregularity of PPGs in shapes after swollen, their strength cannot be easily measured using the conventional methods. Therefore, the open hole screen plate models with various hole diameters and density were designed to establish a simple technique that can be used to measure the strength of …

Online Diagnosis Of Diabetes With Twitter Data, Farheen Ali

Masters Theses

"Innovation in technology enables people to communicate, share information and look for their needs by just sitting in rooms and going through some clicks. While social media has played a very important role in connecting people worldwide, its potential has stretched beyond the innovative idea of connecting people through their social networks. While many thought there was no meeting point for the healthcare sector and social media, it was a surprise when research and innovations have shown that social media could lay a very significant role in the health care sector.

Research has been done in developing models that could …

Determining Rockfall Volumes In Three Sites Along Habs Mountain Road In Southwestern Saudi Arabia, Using Lidar Technology, Abdullah Ayed Al-Otaibi

Masters Theses

"The rugged elevated topography is a characteristic feature of the western and southwestern regions of Saudi Arabia. Few arterial roads connect the scattered villages of these regions to major cities, such as Habs Road in Jazan region. Rock fall poses a serious hazard to people, property and animals along the rock cuts of this road. Although no traditional Rockfall studies have previously been applied to this road, accessibility and rock formation shape and structure variability influenced the choice of using Terrestrial Light Detection And Ranging (LiDAR) technology to calculate the volume of rockfall at selected sites along this road.

Software …

Numerical Study Of Upstream And Downstream Regions Of One Dimensional Detonation Wave In A Dusty Gas Medium, Shubhadeep Banik

Masters Theses

"In detonative combustion very high temperatures are attained by the burned gases. As a result, a large amount of thermal energy is produced during the combustion process. This heat can affect the state of the unburned fuel through radiation of heat from the burned gases. In this study a one-dimensional model was deemed appropriate to gain insight into the fundamental structure of the detonation wave. In this model, the detonation wave divides the fluid stream into an upstream region, consisting of fuel and oxidant, and a downstream region, consisting of burned gases. A set of computer programs, some developed during …

Palynological Interpretations Of Deep Sea Drilling Projects Cores In The Gulf Of Mexico And Bahamian Platform, Adam Patrick Barron

Masters Theses

"One hundred drill core samples were from Deep Sea Drilling Project (DSDP) Sites 94, 98, and 540 were investigated for their palynological contents (pollen, spores, acritarchs, dinoflagellate cysts, and dispersed organic matter) to infer the paleoenvironmental and paleoceanographic history of the Gulf of Mexico and the Bahamian Platform during the middle Eocene to middle Miocene interval. At Sites 94 and 540, abundant dinoflagellate cysts (chiefly Operculodinium centrocarpum, Lingulodinium machaerophorum, Impagidinium sp., Nematosphaeropsis sp., and Spiniferites spp.) were used as paleoenvironmental indicators. Two alternating palynofacies assemblages were identified from dispersed organic matter analysis: terrestrially influenced assemblage A and marine dominated assemblage …

Impact Of Configuration Variations On Small Modular Reactor Core Performance, William Kirby Compton

Masters Theses

"One of the most promising new reactor designs is the Small Modular Reactor (SMR). These reactors, which operate under 300 MWe, will help bring cheap and safe nuclear energy to remote and centralized locations alike. Their ease of construction, advanced passive safety features, and cost effectiveness make these reactors an intriguing option for the near future.

In the work presented here, a neutronics analysis of the Westinghouse SMR was performed. Westinghouse's SMR design is a scaled down version of their AP1000 plant and will produce about 225 MWe of power. Though the parameters of the reactor core will be modeled …

Neutronic Analysis Of Light Water Small Modular Reactor With Flexible Fuel Configurations, Brendan Dsouza

Masters Theses

"The study was focused on the analysis of light water Small Modular Reactor (SMR) with flexible fuel configurations. The core design, based on the Westinghouse UO₂ SMR with less than 5% enrichment was developed using the Monte Carlo N-Particle (MCNP) code. Neutronics analyses of a reference core with UO₂ fuel was performed to characterize parameters such as the radial neutron flux profile, the maximum to average flux ratio, the reactivity coefficient and critical boron concentration at beginning of life; which confirmed good performance in comparison to a standard UO₂ based pressurized water reactor.

Using this uranium oxide …

Evaluation Of Preformed Particle Gel Treatment Using Homogeneous And Heterogeneous Models, Hilary Ogochukwu Elue

Masters Theses

"This research investigates the effects of preformed particle gel (PPG) in remedying the problems of excess water production and low oil recovery of heterogeneous reservoirs by placing the PPG in the high-permeability layer, thus diverting displacing brine to the unswept low permeability layer. This investigation was completed with three tasks.

The first task was to evaluate the PPG swelling kinetics and strength as a function of concentration of brine. The result of this task indicate that PPG prepared with low concentration of brine swells more, becomes weaker, more deformable than PPG prepared with high concentration of brine.

The second task …

Computer Aided Detection Of Oral Lesions On Ct Images, Shaikat Mahmood Galib

Masters Theses

"Oral lesions are important findings on computed tomography images. They are difficult to detect on CT images because of low contrast, arbitrary orientation of objects, complicated topology and lack of clear lines indicating lesions. In this thesis, a fully automatic method to detect oral lesions from dental CT images is proposed to identify (1) Closed boundary lesions and (2) Bone deformation lesions. Two algorithms were developed to recognize these two types of lesions, which cover most of the lesion types that can be found on CT images. The results were validated using a dataset of 52 patients. Using non training …

Comprehensive Benefits Of Green Roofs, Madison R. Gibler

Masters Theses

"Green infrastructure uses vegetation, soils, and natural processes to manage water and create healthier urban environments, providing traditional roof services and alternative stormwater management technologies. Other benefits and impacts are not yet fully understood or valued. Research conducted assesses specific stormwater benefits of green roofs, providing information on nutrient leaching from media; and analyzes potential energy benefits through side-by-side comparisons of full-scale white, traditional black rubber, and green roofs in the mid-continent Missouri climate. Roofing media selection impacted leaching of nutrients, suspended solids, and organic carbon from the tested green roof media. Thermal properties were investigated at the building level, …

Pipeline Leak Detection, Marcia Golmohamadi

Masters Theses

"In the present research two techniques are applied for leak detection in pipelines. The first method is a hardware-based technique which uses ultrasonic wave's emission for pipeline inspection. Ultrasonic waves are propagated in the pipe walls and reflected signal from leakage will be used for pipe analysis. Several Pipes with various dimensions and characteristics are modeled by finite element method using ANSYS. Second order longitudinal modes of ultrasonic waves are emitted in their walls. For this purpose, excited frequency is calculated such that it excites the second order longitude mode. In order to investigate the behavior of emitted wave in …

Initial Fuel Possibilities For The Thorium Molten Salt Reactor, Dustin Gage Green

Masters Theses

"The Generation IV International Forum placed six reactors as priority for research and development to compensate for the world's increasing energy demands. Among the six were Molten Salt Reactors (MSRs). These reactors utilize the Th/²³³U fuel cycle using molten fluoride or chloride salts as coolants. MSRs also have the possibility to use other fissile fuels especially with the first fleet of reactors given the low amount of Uranium-233 available commercially.

With the possibility of diverting from using ²³³U initially, the research presented here will benchmark ²³³U as a main fuel for MSRs using the Thorium Molten …

Characterizing The Influence Of Carbon On The Flowrate And Disinfection Efficacy Of Household Ceramic Water Filters, Jessie Yvonne Hahn

Masters Theses

"Drinking water contamination is a major cause of disease in developing countries. Point of Use (POU) water treatment technologies generally have low initial cost and allow rapid availability of improved water. Ceramic pot filters (CPFs) are a POU water source treatment technology which filter water by gravity through a porous ceramic media. Some filters in use contain carbon remnants left from the fugitive pore former as a dark carbon core. Using disk-shaped experimental ceramic filters produced in the lab to have varying levels of carbon, the percent carbon present was measured and a visual analysis method was developed to determine …

Model Predictive Current Control Of Switched Reluctance Motor With Inductance Auto-Calibration, Xin Li

Masters Theses

"The thesis is composed of three papers, which investigate the application of Model Predictive Controller (MPC) for current control of Switched Reluctance Motor (SRM). Since the conventional hysteresis current control method is not suitable for high power SRM drive system with low inductance and limited switching frequency, MPC is a promising alternative approach for this application. The proposed MPC can cope with the measurement noise as well as uncertainties within the machine inductance profile. In the first paper, a MPC current control method for Double-Stator Switched Reluctance Motor (DSSRM) drives is presented. A direct adaptive estimator is incorporated to follow …

A Study Into Improving Transformer Loading Capability Beyond Nameplate Rating, Aakanksha Pasricha

Masters Theses

"Utilities are becoming increasingly interested in the prospect of overloading the transformers beyond the nameplate rating to meet the increased demand for power as it may be more economically viable than installing a new transformer. The safety of the transformer has to be ensured while overloading it and hence there is a maximum loading beyond which the transformer should not be overloaded. A study has been performed on 38 transformer units and the factors that limit their overloading capability have been analyzed. Ancillary equipment ratings were found to be the most prominent limiting factor. Several case studies and evaluation results …

Emi Analysis Of Dvi Link Connectors, Abhishek Patnaik

Masters Theses

"EMI problems are not uncommon in high speed communication systems. As the system clock frequencies increases, so does the challenges in controlling the EMI in such systems. A connector is a very important part of a high speed communication system. Electromagnetic interference (EMI) is found to be tightly correlated to mode conversion: from differential-mode (DM) signals to common-mode (CM) currents and further to antenna-mode (AM) currents on the outside of cables or enclosures. Moreover, in such high speed systems, coupling to an adjacent cable-connector system is not uncommon. It is essential to understand and quantify this coupling path in order …

Laser Surface And Sub-Surface Repair During Metal Additive Manufacturing, Prudvi Teja Ravi

Masters Theses

"This study examines the use of laser surface treatment to repair surface and subsurface defects. Numerical analysis was performed on laser surface melting using Gaussian heat distribution equations to analyze the depth of the melt pool created by the phenomena. Concurrently, a process map was developed with a planned set of experiments by varying the ranges of laser power and travel speed to determine the dimensions of the melt pool across the gamut. The data generated from both the process studies and the numerical analysis was then used to determine the ideal operating ranges of the process parameters to repair …

Spatial And Temporal Modulation Of Heat Source Using Light Modulator For Advanced Thermography, Arvindvivek Ravichandran

Masters Theses

"Thermography is a Non-Destructive Testing (NDT) method that has found increasing use in industry and research. It has the advantages of being non-contact and be able to interrogate a large surface simultaneously. Active thermography using flash lamps as heat source has been demonstrated for identifying blind holes and delamination in composites. Despite these advancements, active thermographic approach fails to defects like cracks. Under uniform illumination heat flow is predominantly 1D and can easily circumvent a narrow feature. This can be overcome by using a focused light/laser source onto the surface to impose a 3D heat flux. The disadvantage is that …

Signal Integrity Analysis Of A Low Cost Pcb To Pcb System, Kancy Robison

Masters Theses

"This report presents the analysis of a low cost PCB to PCB cable and connector system focusing on its data rate limitations and optimizing transmitter and receiver operations. Economic factors have an ineluctable presence in digital hardware engineering and, as data rates are continually pushed to new bounds, finding cheaper alternatives in hardware while maintaining performance standards becomes more relevant. This study will show the measurement and simulation of a low cost digital system which includes a PCB board, connector, and a multi-pin flex cable (ribbon cable). These S-parameter and TDR measurements/simulations are used to gain an intuition for the …