Digital Commons Network^™

An Evolutionary Algorithm Approach To Actuated Signal Timing Optimization Under Lane-By-Lane Detection Condition, Eric G. Strack

Masters Theses

"Motivated by the need to reduce congestion on the nation's roadway network, this research seeks to determine when a new detection scheme at actuated signalized intersections may help. This new detection scheme is called lane-by-lane detection. It "looks" at traffic in all lanes individually to determine the traffic volume on the roadway. Specifically, the problems addressed are investigating alternate signal timings and investigating the traffic volume's effect on performance of the detection scheme. For the alternate signal timings, an Evolutionary Algorithm (EA) was employed to identify the optimal signal timing. This algorithm creates signal timings and tests them in the …

Het-Cam For The Identification Of Ocular Irritancy In Seawater/Salt Water Sources, Alexander Clovis Winters

Masters Theses

"The Hens Egg Test on the Chorionallantoic Membrane (HET-CAM) is an ocular irritation test proposed to replace tradition ocular investigations such as the Draize eye test that has been criticized because of its use of animals. In this study, the ocular irritation potential of seawater and saltwater sources dosed with different disinfectants has been evaluated using the HET-CAM. The seawater and salt water tested was taken from the main show pools from three aquatic theme parks (San Diego, San Antonio, and Orlando). The three disinfectants considered were sodium hypochlorite (NaOCl), calcium hypochlorite (Ca(OCl)₂), and ozone (O₃).

Three different HET-CAM methods …

Applications Of Swarm, Evolutionary And Quantum Algorithms In System Identification And Digital Filter Design, Bipul Luitel

Masters Theses

"The thesis focuses on the application of computational intelligence (CI) techniques for two problems - system identification and digital filter design. In system identification, different case studies have been carried out with equal or reduced number of orders as the original system and also in identifying a blackbox model. Lowpass, Highpass, Bandpass and Bandstop FIR and Lowpass IIR filters have been designed using three algorithms using two different fitness functions. Particle Swarm Optimization (PSO), Differential Evolution based PSO (DEPSO) and PSO with Quantum Infusion (PSO-QI) algorithms have been applied in this work"--Abstract, page iii.

The Effects Of Technology On Literacy(S), Thomas Glen Petersen

Masters Theses

"One of the challenges when measuring the effects of technology on literacy(s) is finding a control group where technology; does not play a major role in the culture. The Amish successfully live in a Technocracy where mechanical/electronic tools are used only when absolutely necessary; the Amish are not dependent on them for survival. The crux of the Amish philosophy is humility, serving the community and serving God. Ironically, they have suffered tremendous repercussions for adopting a wholesome, selfless lifestyle which is contrary to most popular world views, regardless of religious or spiritual views"--Purpose, page 40.

Information Flow Properties For Cyber-Physical Systems, Rav Akella

Masters Theses

"In cyber-physical systems, which are the integrations of computational and physical processes, security properties are difficult to enforce. Fundamentally, physically observable behavior leads to violations of confidentiality. This work analyzes certain noninterference based security properties to ensure that interactions between the cyber and physical processes preserve confidentiality. A considerable barrier to this analysis is the representation of physical system interactions at the cyber-level. This thesis presents encoding of these physical system properties into a discrete event system and represents the cyber-physical system using Security Process Algebra (SPA). The model checker, Checker of Persistent Security (CoPS) shows Bisimulation based NonDeducibility on …

Decision-Based Design Under Uncertainty With Intervals, Sashank Vasireddy

Masters Theses

"Design requires a series of decisions, and one of the major challenges engineering designers face is making decisions under uncertainty. The engineering designer must choose the best design among various alternatives. This work evaluates the use of utility functions to make decisions under uncertainty with both random and interval variables. Uncertainty cannot be eliminated completely, but it can be reduced. Most current methods treat only aleatory uncertainty. Here, however, both aleatory and epistemic uncertainties are addressed in the context of engineering design. Methods such as moment matching method and worst case analysis are used to incorporate uncertainty into design problems"--Abstract, …

Continuous Control Of Lunar Orbits Via Electric Propulsion, Sunil Aggarwal

Masters Theses

"To find definite answers for the presence of water on the poles of Moon, to facilitate selection of future lunar landing sites and aid in construction of architectural bases, to assist proper lunar resource utilization and to improve lunar gravity models there is a great interest and need for highly accurate, reliable and efficient lunar surface mapping and communication. This thesis is intended to aid in proper selection of orbits for future lunar missions by demonstrating the impact of using electric propulsion on the search space of feasible and useful lunar orbits. The requirements for future lunar mapping and communication …

Verifying Module Heuristics For Large Scale Products, Rachel Marie Day

Masters Theses

"Decreasing time and costs is a major objective in many businesses today. Including modularity in the early design phases can effectively decrease time spent on and costs associated with a project. The task of identifying modules within a product early in the design process (when decisions are less expensive) is made less daunting by using the techniques of functional modeling and module heuristics. The two papers that form this thesis discuss the results of the efforts to verify the module heuristics on large products. Observations on needed modifications to the functional modeling technique and original module heuristics are reported along …

Modeling And Simulation Of Electrochemical Magneto Hydro Dynamics, Debamoy Sen

Masters Theses

"This thesis focuses on how the electrochemical magneto hydro dynamic problem is solved through numerical simulation for a two dimensional millielectrode electrochemical cell and a three dimensional microelectrode array cell. Electrochemical processes are enhanced by magnetic fields through the introduction of body forces such as Lorentz force. Through modeling and numerical simulations, experimental results can be integrated with theory. Such simulations will aid in the prediction of mass transfer limited currents and visualization of flow profiles in an electrochemical cell. The numerical solution of the equation system is made possible by the finite volume method used in the FLUENT Computational …

Electricity Generation And Ethanol Production Using Iron-Reducing, Haloalkaliphilic Bacteria, Varun Paul

Masters Theses

"Microbial life in extreme environments has been studied primarily for their metabolic activities. Very few commercial or industrial applications have been known from these systems. In this study, the metabolic pathways and properties of bacteria from a haloalkaliphilic environment of Soap Lake, Washington were employed in two research applications related to energy production. In the first study, the bacterial cultures that were known to reduce iron (III) were used in a Microbial Fuel Cell (MFC) reactor. Iron reducing bacteria have shown to shunt their electrons on to the surface of a carbon electrode of an MFC, and the electrons can …

Exploring The Use Of A Commercial Game Engine For The Development Of Educational Software, Hussain Alafaireet

Masters Theses

"Three-dimensional visualization and simulation environments are becoming increasingly important in both industrial and educational environments. However, developing these simulations can be a difficult and expensive task. Herein we explore the use of a commercial game engine to develop a 3-D, interactive computer game designed to teach players about the anatomy of a frog. The goal of this project is threefold: 1) to develop high-fidelity virtual reality educational software with a limited budget and limited personnel, 2) to define a software development process by which similar simulations can be developed, and 3) to explore the benefits that these simulations provide to …

Modeling Of Vias And Via Arrays In High Speed Printed Circuit Boards, Arun Reddy Chada

Masters Theses

"This thesis presents modeling approaches for fast calculation of signals in dense via arrays in high speed printed circuit boards (PCBs) and model to hardware correlation study of solid and perforated disk resonators. A 2D finite difference (FD) method to extract the via capacitance which includes the via pad capacitance obtained by solving the laplace equation in the via domain in multi-layer geometries is presented and validated with analytical formulation for via capacitance. Next, closed-form expression for the impedance of an infinitely large parallel plane pair is derived and validated by comparing with cavity model for several numerical examples. The …

Preventing Chemical Product Failure, Kenneth Ombete

Masters Theses

"The purpose of this thesis is to demonstrate a research methodology to prevent chemical product failures. This methodology extends the risk in early design (RED) method for prevention of failure in electromechanical products to include products with chemical subsystems. Inclusion of this domain is demanded by the ever-growing semiconductor and energy industries. The RED method was extended by first identifying principal chemical failure modes and adding them to the failure mode taxonomy. The RED database was then augmented with historical failures of products that included chemical subsystems. Finally, the extension was validated with a case study of a fuel cell"--Abstract, …

Control Aspects Of A Double-Input Buckboost Power Electronic Converter, Deepak Somayajula

Masters Theses

"Systems in which two or more energy sources combine to supply power to a common load are called hybrid energy systems. Applications of these systems have grown due to their flexibility and reliability. Hybrid energy systems have been successfully implemented in hybrid electric vehicles and wind-solar systems where two or more energy sources share the same load. Double-input (DI) dc-dc power electronic converters (DIPECs) have been gaining popularity in hybrid energy systems due to their reduced component count and control simplicity. In addition, employing DIPECs increases the reliability, stability, and flexibility of the system. In this thesis, a small-signal model …

Numerical Modeling And Analysis Of Complex Electromagnetic Structures, Including Those Containing Ferrites, Andrea Orlando

Masters Theses

"Application of fast switching amplifiers in power converters, and especially in power inverters, causes unwanted radiated emission, which is a consequence of common mode (CM) currents arising in feed wire bundles. Ferrite chokes are commonly used to suppress those CM currents by increasing the CM impedance of circuits without affecting the differential mode currents, which is important for undisturbed operation of the converters or inverters. Their effective impedance is the main design concern, and it is determined by the material intrinsic properties (permeability, permittivity) and geometry. The goal of this work is to analytically correlate the geometrical and material properties …

Reliability-Based Design With System Reliability And Design Improvement, Gagandeep Singh Saini

Masters Theses

"This thesis focuses on developing a methodology for accurately estimating series system probability of failure. Existing methods for series system based design optimization are not that accurate because they assign reliability to each failure mode; as a result complete system reliability goes down. According to method proposed in this work, the user will assign required system reliability at the start and then optimizer will apportion reliability to every failure mode in order to meet required system reliability level. Detlevson second order upper bounds are used to estimate system probability of failure. Several examples have been shown to verify the results …

Screw Connections Subject To Tension Pull-Out And Shear Forces, Ryan M. Francka

Masters Theses

"Currently, the behavior of screw connections subject to combined tension pull-out and shear forces is not well understood. An experimental study was conducted at Missouri University of Science and Technology to better understand the relationship or interaction between these forces. The test program evaluated four parameters that may influence the behavior of pure tension and pure shear in screw connections: the thickness of the sheet not in contact with the screw head, the ultimate strength of the steel, the ductility of the steel, and the screw diameter. This investigation extends the application of the pure pull-out and pure shear equations …

Analogy Based Modeling Of Natural Convection, Vaibhav Khane

Masters Theses

"This research is an extension of previous work on the development of an integrator or resistance-capacitance circuit analogy for natural convection. As a part of a larger project to enhance transport phenomenon on a micro-scale using radiation, this work studied the phenomenon of natural convection. Using experimental techniques and numerical simulations (FLUENT code), it investigated the transient response of a natural convection system. It proposes an integrator circuit analogy for a natural convection system. Experimental investigation with three different fluids indicated that the characteristic time constant of the system is related to the Prandtl number of the fluid. The project …

Fault Detection And Prediction With Application To Rotating Machinery, Gary R. Halligan

Masters Theses

"In this thesis, the detection and prediction of faults in rotating machinery is undertaken and presented in two papers. In the first paper, Principal Component Analysis (PCA), a well known data-driven dimension reduction technique, is applied to data for normal operation and four fault conditions from a one-half horsepower centrifugal water pump. Fault isolation in this scheme is done by observing the location of the data points in the Principal Component domain, and the time to failure (TTF) is calculated by applying statistical regression on the resulting PC scores. The application of the proposed scheme demonstrated that PCA was able …

Formation Of Iron-Rimmed Sandstone Nodules On Earth; Terrestrial Analogue For The Formation Of Martian Blueberries?, Katherine Charlotte Muller

Masters Theses

"NASA's twin Mars Exploration Rovers, MER, Spirit and Opportunity, have identified numerous geologic features that hint at a watery past on Mars noted in Malik, 2004. Prominent among these features are the "Martian Blueberries" that occur as spherical hematite (Fe₂O₃) nodules. Hematite formation is facilitated by the presence of water, although there are presently no known sources of free liquid water on Mars. Chan et al., 2004 states that these "blueberries" are also similar to nodules found in the Jurassic aged Navajo Sandstone in Utah. An understanding of the processes controlling the formation of the Utah nodules may thus be …

Feasibility Of A Human Performance Model In Consequence Management, Kashmeera Ghosh

Masters Theses

"Human civilization has always encountered unpredictable disasters as a result of natural events. Now it also faces the disasters caused by terrorist attacks. Governments must have consequence management plans in place to protect public health and safety, restore essential services, and provide emergency relief to affected businesses and individuals. Human performance models predict outcomes in complex dynamic situations. Such models can simulate disaster management procedures under varying circumstances. This work applies human performance modeling in a terrorist situation and evaluates possible uses of such models by first responders in practical consequence management applications. It includes a case study of an …

Real-Time Reconfiguration Of Programmable Logic Controller Communication Paths, Curtis Alan Parrott

Masters Theses

"This thesis explores the topics related to reconfiguration of Programmable Logic Controller's (PLC's) communications paths as it relates to network security and reliability. These paths are normally fixed, which creates a single fault point which can easily be disrupted by network failure or network based attack. With the ability for autonomous communications path reconfiguration these disruptions in communications can be avoided or bypassed. This work builds on these principles and a series of PLC programs are developed to facilitate several things: Scanning of the three different network types most common in PLC to PLC communications; a comprehensive network scan routine …

Cover And Contents

Turkish Journal of Physics

No abstract provided.

Cover And Contents

Turkish Journal of Physics

No abstract provided.

Development Of Extrusion On Demand For Ceramic Freeze-Form Extrusion Fabrication Processes, Parimal Sanjay Kulkarni

Masters Theses

"Freeze-form Extrusion Fabrication (FEF) is a Solid Freeform Fabrication method. It involves the deposition of a ceramic paste in a layer by layer manner to construct a three dimensional structure. The ceramic paste used in this process consists of a high solids loading of ceramic powder mixed with water and a nominal amount of an aqueous organic binder. These characteristics make the process environmentally friendly. Also the absence of dies or molds in the process makes it suitable for fabrication of materials like ceramics. In the past, parts have been fabricated with continuous extrusion of a ceramic paste. In FEF, …

Inclusion Modification In Steel Castings Using Automated Inclusion Analysis, Vintee Singh

Masters Theses

"The objective of this research is to study the effects of changing the melt and ladle practices (deoxidation, slag, refractory types, etc.) in steel foundries on the cleanliness and toughness of steel castings. This study used an automated inclusion analyzer ASPEX PICA-1020, which provides a rapid and accurate method for determining the composition, size, number, and spacing of the inclusions present in steel samples. The first step in this research was to complete a series of industrial tests to benchmark the current foundry ladle practices with respect to cleanliness of the cast steel. Trials were conducted at steel foundries using …

Electric Multipole Moments Of Some Diatomic Molecules Molecules, M. Özgür Sezer, Ayhan Özmen, Hüseyi̇n Yüksel

Turkish Journal of Physics

Molecular Electric Multipole Moment (MEMM) integrals have been derived for diatomic molecular systems, and then some lower multipole moments as dipole moments and quadrupole moments have been calculated for some diatomic molecules. The calculations have been performed by using our analytical formula over Slater-Type orbitals (STOs) with Cade and Huo's basis sets and the GAMESS program package working with Gaussian-Type basis sets (GTOs). The expressions which involve factorials are given in terms of binomial coefficients in order to speed up calculations. The results have been obtained in agreement with data found in the literature.

Cover And Contents

Turkish Journal of Physics

No abstract provided.

Application Of Ground Penetrating Radar (Gpr) For Bridge Deck Condition Assessment: Using A 1.5 Ghz Ground-Coupled Antenna, Amos Wamweya

Masters Theses

"This study is a GPR-based assessment of three bridge decks, two with a hot bituminous wearing surface and one with a bare concrete slab. The primary objectives of this study were: 1) to assess the integrity of the three bridge decks using a 1.5 GHz ground-coupled GPR antenna, and 2) to evaluate the utility of the 1.5 GHz ground-coupled antenna for bridge deck investigations. Core control (chloride ion concentration data and core integrity data) and visual inspection were used as interpretive constraint. The acquired GPR data were interpreted, and two plan view maps were generated. One depicts the magnitude of …

Bint 3522 Neu Sp09, Terris Neuman Dr.

Syllabus Repository

No abstract provided.