Digital Commons Network^™

Educational/Informational Posters On Graphic Design, Sister Mary Kay Neff S.C.

Theses

I intended to design a series of orientation posters to be used as educational/informational aids in the study of graphic design. These posters might deal with the following topics: -introduction to graphic design -tools of graphic design -history of graphic design -organizational and perceptual principles -typography -image formulation -applications of graphic design

A Low-Noise Ccd Electrometer Using Buried-Channel Ldd Nmosfets, Eric G. Stevens

Theses

A iow-noise, CCD electrometer is presented that makes use of devices akin to buried-channel, LDD NMOS FETs. Self-aligned source and drain contacts are used that result in high performance and a simplified process. These devices were fabricated in a scaled, buried-channel NMOS CCD process without adding any process complexity. In spite of the higher capacitances associated with the scaled process (higher levels of doping and thinner gate oxides) in which this device was constructed, the input referred voltage responsivity or sensitivity of this electrometer is 15 /xV/electron, the highest reported to date. This high responsivity leads to superior noise performance. …

Design And Testing Of A Computer-Controlled Square Wave Voltammetry Instrument, Nancy L. Wengenack

Theses

Square Wave Voltammetry is rapidly becoming the most popular and versatile electrochemical technique used in research laboratories today. A discussion of electroanalytical techniques, which are the forerunners to square wave voltammetry, provides a basis for understanding the theoretical and experimental aspects of SWV which are presented. A computer-controlled square wave voltammetry system was designed and built using an IBM PC computer, a Tecmar data acquisition board, an EG&G PARC Model 264A Polarographic Analyzer/Stripping Voltammeter, an EG&G PARC Model 303A Static Mercury Drop Electrode, and the scientific software package, ASYST. The system was tested by performing computer-controlled square wave voltammetry on …

A Mathematical Model Of Photopolymerization In A Batch Reactor, Jyh-Yao Li

Theses

A mathematical model of a photo initiated additionpolymerization in a batch reactor was developed.

The model considered initiation, propagation and, termination to simulate the addition polymerization process, The model has the advantage that the concentration of any particular n-mer may be calculated without calculating all of its precursors. Other methods do not have this property. An analytical solution to the model for the photopolymerization of styrene was solved. The calculations were run on a VAX 8800 computer and the results were then compared with the experimental results. The calculated results fitted the experimental results to some extent. Effects from the …

Process Hazard Review For Drug Development, Rudolph R. Schwarz

Theses

The development of drugs has become increasingly complex, requiring the use of a wide variety of pharmaceutical actives and isolated intermediates, a majority of which are not always completely characterized with respect to their hazard potential. This can present a source of potential exposure to those who handle these substances during initial drug development, manufacturing of the drug active and ultimately the finished pharamaceutical product. It is, therefore, essential that safety and health information be documented and communicated during the entire drug development process.

The need for application of process hazard review techniques to the development of new drug materials …

Studies Directed Toward Beta-Cyclodextrin And Capped Beta-Cyclodextrin Mimics Of Alpha-Chymotrypsin, Preston Marlon Canzius

Theses

Molecular mechanics calculations were used to investigate beta-cyclodextrin and capped beta-cyclodextrin as models for the active site of alpha-chymotrypsin. The Amber molecular mechanics force field was used to investigate the effect that addition of the caps has on the conformation of the beta-cyclodextrin macrocycle.

The RMS module of Amber was used to calculate differences in position between the atoms of the minimized mimics and those of the X-ray crystal structure. The deviation in position of the atoms of the minimized capped beta-cyclodextrin macrocycle was found to be larger than that of the minimized beta-cyclodextrin, indicating that the caps do affect …

Characterization Of Pulse Duplicator Model For Testing Of Heart Valves, Pankesh Nilkamal Kadam

Theses

The design and development of a pulse duplicator system for testing of prosthetic valves is described. The performance characteristics were evaluated by computing the input impedance of the system from the measured pressure and flow signals for different simulation configurations. The study has been further extended to determine the feasibility of evaluating the cardiovascular status of a patient after major open heart procedure or in state of shock.

Built on hydrodynamic principles, the model allows for a wide range of heart rates, flow rates and mean pressures to be simulated. The artificial circulatory system used as a load to the …

Feasibility Of State-Of-The-Art Project Planning Techniques In Pakistan, Ahmed Mansoor Ansari

Theses

The objective of this work is two-fold:

1. Technological transfer of the best suitable state of the art techniques for implementation in the construction industry of Pakistan.

2. A vehicle intended for American readers to gain insight of the present methods of working in Pakistan.

In harmony to the first of the forestated ambitions this work covers subjects widely ranging from introducing the concept of proven scheduling techniques as CPM, PERT to the application of these techniques via advanced computer technology.

Frequently, American professionals and consulting firms are invited to participate to administer or design specialist construction projects in Pakistan. …

Management Training In Small Business, Harry L. Bargholz

Theses

Human Resources Professionals are often faced with the issue of "the need for and usefulness of management training." In addition, small business people believe that the needed training is unwanted and, in somecases, impossible to deliver. On the other side of the issue, training supporters point to the need for knowledge, the constant obsolescence of learned skills and the highly competitive nature of the marketplace.

The argument continues that whereas managers in larger firms may be able to afford numerous in-house training programs or be able to send employees to assorted workshops and conferences, the manager in a small enterprise …

Study Of Reliability And Failure Mechanism Of Solid Tantalum Capacitor, Rajan N. Bhatt

Theses

Today, reliability is acknowledged as an important item in design and operation of the electronic systems.

This thesis provides some theory, and experiments are instituted to evaluate the reliability of SOLID TANTALUM CAPACITORS made by reputed manufacturers. The experiment was conducted on four batches of tantalum capacitors at different temperatures at different humidity levels. One chapter is on different manufacturing techniques presently applied.

Literature study concentrates on the reliability in solid tantalum capacitors developed between 1961 and 1986.

Several failure mechanism with figure are illustrated to point out how higher reliability of solid tantalum capacitor may be developed.

The bibliography …

Ksc2408 Digital Filter Evaluation System For The Ecg, Chi-Tong Chung

Theses

A hardware implementation in digital filters by using the high speed and high precision KSC2408 digital filter chips, demonstrates the power of the KSC2408 and proves that the real time digital filters can be implemented without complex circuitry and without high expense.

The system consists of two parts - the digital filter board and the IBM PC; the former handles the data filtering, the latter handles the analog-to-digital data conversion and data display. The KSC2408 is programmed as a 16th order Butterworth digital filter to have flat response in the passband and good attenuation in the stopband.

Recruitment Of Engineers In A Small Company, Robert Cohen

Theses

With most recruitment techniques written for large companies, recruitment of engineers in a small company may be a large problem. A detailed analysis of the engineering employer and employee is constructed making note of large and small company differences. A survey was taken and the results are presented in support of the authors opinions. A generic recruitment technique is also presented, followed by modifications or other considerations to that technique. This should increase the available applicant pool and optimize quality levels of the engineering candidates for the small company.

Energy Analysis Of A Multistory Office Building Using Bin Method Computer Program, Mohammed Nasim Ghauri

Theses

The consumption of energy by an HVAC system in a high rise office building was investigated by comparing results obtained from ASEAM and Trakload (two microcomputer programs) with the manual calculations and DOE-2 (Department of Energy Program) results obtained by Tishman Research Corporation. The study was performed on the Public Service Building of Newark, New Jersey. It is a 26 story office building, designed to be energy efficient.

The results obtained show that, the energy consumed by the HVAC system is a substantial amount of the total energy used but the controlling factors are electrical lighting and equipment. Both of …

Reliability Evaluation Of Liquid Crystal Displays Under Accelerated Life Conditions, Rajkumar Krishnamoorthy

Theses

This Thesis shows method of comparing the reliability of Liquid Crystal Display Devices by means of accelerated life testing at elevated temperature and relative humidity for two different vendors.

The tests were carried out at three different combinations of temperature and humidity.

1. 77°±1° C and no added humidity.

2. 85°±1° C and no added humidity

3. 98°±1° C and 98+2% relative humidity.

Leakage current measurements were carried out after every 1000 hours for up to 5000 hours for vendor no.l. Measurements were carried at 0, 500, 1000, 2000, 3000 and 5000 hours for vendor no.2. A DC bias of …

Image Analyzing Instrumentation System For The Activity Measurement Of Rats, Yun-Kang Li

Theses

A microcomputer based instrumentation system has been developed to measure the activity of rats in 12 metabolic chambers. The instrumentation system monitors the rats' behaviors and estimates their activity continuously in an automatic manner. The activity information of the rats are expressed by a quantitative index which describes the intensity of the activity level.

An Apple II microcomputer system is used to manage the activity measurement which consists of an image recording operation and an image analyzing operation. During the measurement, the microcomputer controls Optic RAM digital cameras to record the rats' image. The camera can take a digital picture …

Analysis Of Polycyclic Aromatic Hydrocarbon (Pah) In Stack Sample Particulates Formed During Waste Combustion ; Substituent Effects On The Strain Molecules, Ping Chiang Lyu

Theses

PART A: The total thirty samples came from wastes incineration of five industry companies in New Jersey have been examined. The EOM levels showed, especially for the less polar substances, lower than if they were collected at room temperature in the manner of ambient sampling. HPLC analyses of PAH, nitro-PAH and Quinone-PAH have been performed. Brief comparison is made with previous study.

PART B: Ab initio Molecular orbital calculations using the 3-21G basis set provide good approximations to the experimental geometries of substituted strained organic molecules. A series of disubstituted prismanes have been calculated at this level and the effects …

Bond Behavior Of Reinforced Concrete Under Impact Loading, Abu Rayhan Md Muniruzzaman

Theses

This thesis covers experimental investigations of bond behavior of reinforced concrete specimen under impact loading. A computer assisted data acquisition system was selected for data acquisition and control. This entire electronic system involved mainly a multichannel digital oscilloscope and an IBM-AT micro computer. All specimens were tested by a modified instrumented Charpy tester assisted by the electronic system.

15 test specimen were prepared in order to perform the experimental investigations. Each 3x3x16 inch specimen was reinforced with a single deformed bar mainly 3/4" and 1/2" diameter and three catagories of concrete mainly plain, 1%, and 2% (by volume) steel fiber …

Optimization Of The Design Of The Harrington Distraction Rod And Hooks, Margaret Ann Pisani

Theses

The Harrington Distraction Rod is presently attached to the spines of patients who suffer from scoliosis and vertebral fractures. The rod's purpose is to apply a distractive force to the scoliotic curve in an attempt to reduce its severity. In fractures this rod is implanted to reduce the fracture and increase the stability of the spinal column. Harrington distraction rods are also inserted in order to give mechanical support to the spinal column.

Presently the Harrington Distraction Rod, manufactured by Zimmer, is one—quarter inch in diameter and made of 316L cold—worked stainless steel. The proximal end of the rod consists …

Finite Element Analysis Of The Temperature Field In The Course Of Laser Heating, Moududur Rahman

Theses

This study is aimed at the developement of a computational procedure for the prediction of temperature and the concentration fields in the course of surface processing by high energy beams. The finite element technique is used for the solution of two dimensional problem of heat conduction in a solid subjected to the laser radiation. The preprocessing, solution and the postprocessing were carried out by the use of ANSYS software package. The laser energy was simulated by heat generation at the shallow subsurface or by the temperature of the impingement zone. Equal square elements were used for computations. It was found …

Investigation Of The Size Of Gallium Clusters Formed Using A Modified Ion Cluster Beam Source With A Crucible Temperature Of 1250 Degrees C, Sujit M. Shah

Theses

Energy analysis of the ionized gallium clusters was done by retarding field method. The objective of this research was to investigate the possibility of gallium cluster formation during nozzle jet expansion and to estimate the probability of ionization of clusters. The measurements at a crucible temperature of 1250°C corresponding to gallium vapor pressure of 0.23 torr (inside the crucible) showed that no large cluster sizes could be obtained. The relationship between mass deposition rate (atoms/cm2-sec) and cluster size (atoms/cluster) showed that there were two distinct peaks. One with a cluster size of 1 atom/cluster and the other with about 13 …

Reliability Studies On Microcircuit, Salim Shehadeh

Theses

The primary objective of this thesis is to determine and analyze the failure mechanisms of Low Power Schottky microcircuit device (2-Input NAND Gate). Pinpoint the causes, and suggest the precautionary measures that prevent the occurrence of these failures. To achieve this goal, the study went in two directions, theoretical and experimental. The theoretical part is a comprehensive review of the work done on Low Power Schottky 2-Input NAND Gates since 1960 up to date.

The experimental part of the study is a life test ( 1000 hours ) of 2-Input NAND Gates under humidity and high temperature.

For each unit, …

Life Testing Of Solid Dielectric Materials, Muhammad Irfan Soomro

Theses

The main objective of this thesis was to find correlation between the electrical noise generated within the body of the solid dielectric material with the failure (puncture), under simultaneously applied thermal and electrical stresses.

The term 'Corona' is commonly used to describe any partial discharges occurring in voids (defects) in the material. Precisely corona is a flow of electrons and ions which occur in a void in air or other gasses. This event emits acoustic, optical and radio frequency energy, and can be detected by measuring any of these radiations. In the present thesis, Radio Interference Voltage (RIV) technique was …

Method Of Moments Analysis Of Very Thin Wires Using The Mini-Numerical Electromagnetics Code, Douglas F. Stolarz

Theses

The analysis of thin wire antenna systems in the presence of a conducting ground plane is an important engineering problem. This thesis presents an analysis of wire radiators using the method of moments as implemented in the Mini-Numerical Electromagnetics Code (MININEC). Due to singularities in the formulation, MININEC yields inaccurate results for very thin wires. This code was modified by introducing filament currents for very thin wire structures thereby eliminating inaccuracy due to the treatment of singularities.

The modified code was tested on a monopole over a perfect ground, symmetrical and asymmetrical dipoles in free space, and inverted L and …

Simulation Of Hvac Systems And Library Building Of New Jersey Institute Of Technology Newark, N.J., Muhammad A. Syed

Theses

The HVCASIM⁺ Building Systems and Equipment simulation program package developed at National Bureau of Standards has been used to simulate the building load and HVAC systems of N.J.I.T. library building, This report describes the procedure and strategy adopted to simulate the library building and the HVAC systems.

The library building has been simulated with two different sets of parameters, first with original design data and then with modifications for energy conservation, which ware suggested by the energy management consultants M/s Engineers Incorporated, as a part of the New Jersey Department of Energy School Grant program.

The results of tho …

Probabilistic Technique In Power Flow Analysis, Dun-Ren Tzeng

Theses

This thesis describes and examines a technique which permits the power flow problem in a power system to be analyzed probabilistically. Both the deterministic and the probabilistic power flow theories have been presented. A mathematical model and a program have been developed to carry out the probabilistic power flow calculation. Two power systems and seven different loading cases have been used to test the technique. The results including the sensitivity coefficient matrices, the expected line flows with their variances, and 25 of 176 probability density function curves, have been shown and discussed. An easy way to predict the possible abnormal …

A Cad Tool For Edif Model Generation, Sri Nagesh Valluri

Theses

This thesis describes a new CAD tool designed to create models proposed by Electronic Design Interchange Format steering committee. In its present form the system can generate models for standard SSI and MSI devices. The menu driven window based fillup the form features of the tool allows a novice user to provide structural and timing informations of the device from any manufacture's data book. The software performs online checking of the user data and guides them to generate the correct model.

On Weakly Coupled Hyperbolic And Parabolic Partial Differential Equations Arising In Chemical Engineering Problems, Zhifeng Zhang

Theses

Many of the mathematical models arising in dynamical chemical processes are systems of weakly coupled hyperbolic and parabolic partial differential equations with constant coefficients. It is shown in this paper that this kind of systems of partial differential equations can be treated using generalizations of Green's functions. The Green's function is completely defined, including all boundary conditions, for systems with nonselfadjoint operators as well as those which are selfadjoint. The Green's functions can be expressed in terms of eigenvalues and eigenfunctions of the operator and the adjoint operator when they can be obtained. We develop a method based on higher …

Geometric And Enthalpic Calculational Study Of Monosubstituted Cyclobutanes ; Attempted Synthesis Of 1,3-Diphenyl-2,2,4,4-Tetrafluorobicyclo [1.1.0] Butane, Jose Luis Reyesgavilan

Theses

The work undertaken in this thesis is in two parts. In the first, the structure and heat of formation of substituted cyclobutanes were studied via the computer program MMII using an IBM PCXT personal computer with a math co-processor chip. Structurally, a trend was seen to be followed in which bulkier substituents were pushed away from any steric interaction with the ring. This was accomplished by having the latter alter its puckering angle, C2C1C4 angle, HCX angle, and to a smaller extent, the bond lengths immediately adjacent to the substituted carbon atom. This results demonstrated that the ring was very …

Stress Analysis Of A Stepped Shaft With A Keyway, Irfan Hussain Sabir

Theses

A stress concentration case which is encountered in practice more than any other is the shoulder fillet. Shafts, axles, spindles, rotors etc., usually involve, in each case, a number of diameters connected by shoulders with fillet radii and very often it is necessary for a keyway to be near a shoulder. The objective in this study is to analyse the stresses in a shouldered shaft with a keyway subjected to an axial tensile load and to study the dependence of the keyway-end stresses on the distance between the shoulder fillet and the keyway end. This is done by performing a …

Wear And Development Of Wear Testing Methodology, Tirumalai S. Suresh

Theses

The existing wear and friction theories, and wear testing methods have been analysed to meet the objective of this study. One of the key factors in the analysis of a wear problem is the computation of wear and friction coefficient for a material, under real operating conditions. A new wear testing methodology has been developed and a wear tester has been designed and assembled. The tests have been performed at constant sliding speed and different applied loads for a Cast-Iron - hardened Steel pair.