Digital Commons Network^™

A Study Of The Epic Delta Dampening System's Ability To Eliminate Plate-Caused Hickeys, Noelle Lara Folkes

Theses

The purpose of this study was to determine if the Epic Delta dampening system removed and eliminated 98% of the plate-caused hickeys that occurred on press runs with a continuous plate-feed dampening system. This was accomplished by comparing the proportion of hickeys per 10,000 cartons that occurred with a continuous plate-feed dampening system, to the proportion of hickeys per 10,000 cartons that occurred with the Epic Delta dampening system. The data were obtained from carton quality audits of jobs run on a press with a continuous plate-feed dampener and carton quality audits of the same jobs run on the same …

English-Spanish-American Sign Language Translation Program, Janise Maria Negron

Theses

None provided.

Corporate Identity Systems And Color Publishing On The Macintosh, Mary Parell

Theses

None provided.

Arbol De La Vida, Carisa Cannan

Theses

None provided.

Design For Quality Manufacturability Analysis For Common Assembly Process, Suriyanarayanan Ramachandra

Theses

The globalization of market economy has precipitated a dramatic increase in competition necessitating the need for higher quality products at lower cost in shorter time periods. Shorter life cycles and proliferation of products has made companies integrate all the phases of manufacturing to bring about a superior design. Design for Quality Manufacturability (DFQM) provides a technique to invoke manufacturing and assembly considerations while designing a product. The DFQM architecture identifies factors consisting of several variables that are influenced by certain error catalysts to cause one or more specific defects. A methodology is suggested to identify and quantify these error catalysts …

Wear And Friction Of Hylamer And Polyethylene Against Cobalt Chromium A Pin-On-Disc Study, Jerry D'Alessio, Ii

Theses

Understanding friction and wear of biomaterials is essential to the success of any prosthetic joint. A pin-on-disc wear tester is used to find the friction and wear of pins of one material on a coupon of medical grade cobalt chrome. In this experiment six pins of UHMWPe (ultra high molecular weight polyethylene) and six pins of Hylamer® from Du Pont Manufacturing were tested. Four separate runs were made. The tests were performed for ten million cycles, stopping every one to one and a half million cycles for data acquisition. Volumetric wear, wear rate, and coefficients of friction were measured. Both …

An Adaptive Asynchronous Cdma Receiver And Its Convergence Analysis, Lizhi Zhong

Theses

An adaptive CDMA receiver scheme assuming perfect synchronization has been generalized in this thesis to the asynchronous channel, a much more practical assumption of the real system. Similar formulas are derived and as its synchronous version, it is still near-far resistant and requires no knowldge [sic] of received signal amplitudes and training sequences. Thus, sophisticated high-precision power control and user power estimation are not necessary and the receiver is particularly useful in mobile communications since it can adjust itself adaptively to changes in the power of the users. Tile convergence and transient behavior of the receiver are also investigated and …

Development Of A Multi-Lead Trans-Thoracic Impedance Pneumograph For Heart Rate Variability Studies, Curtis Bashford

Theses

In this study, a device that measures respiratory tidal volume and ECG for use in heart rate variability studies, was designed, built and tested. The device developed is a Multi-Lead Trans-Thoracic Impedance Pneumograph, which determines tidal volume on a breath by breath basis, utilizing both hardware and software. It uses standard ECG electrodes which provide increased comfort and inability to the subject over traditional spirometry methods. The device operates similar to traditional bipolar impedance pneumographs except that instead of only one lead (electrode pair), four leads are acquired simultaneously using time-division multiplexing; providing data from different locations and vectors on …

Wear Of Polyethylene And Hylamer On Cobalt-Chromium : A Knee Simulator Study, Alessandro F. Canonaco

Theses

Two tests were conducted to examine the wear characteristics of tibial bearings used in total knee replacement systems. Each test consisted of six A/P Glide Tibial Bearings each having a conical control arm. The plastic portion of the conical bearings were all made of UHMWPe. Each of these bearing systems was mounted onto a Co-Cr alloy tibial platform and Co-Cr alloy LCS (low contact stress) femoral component . These test samples were mounted onto the New Jersey Mark III Knee Simulator System. The simulator was configured to produce flexion and axial rotation to simulates normal gait. Each test ran at …

Investigation Of Velocity Distribution Within High Speed Waterjet, Hong Cao

Theses

The aim of this research was to investigate velocity distribution within the water jet at different conditions of jet formation. The water jet (WJ) velocity was measured by the use of Laser Transit Anemometer (LTA) and statistical technique which improved the accuracy of the velocity determination.

The velocities were measured for different diameters of the sapphire nozzle under different water pressures at different axial stand off distances and radial distances across the jet. The experiments performed in this study enabled us to evaluate the effects and conditions of the water jet on the velocity distribution. The acquired results provide information …

Performance Evaluation And Sequence Control Of An Automatedmanufacturing System, Vijaykumar D. Desai

Theses

In an automated sequential manufacturing system Programmable Logic Controllers (PLC) are widely used. As the control specification varies, the control software needs to be rewritten to accommodate the new specification. Since PLC has high flexibility, one can update the current system while it is running thereby making easier implementation. In order to design flexible, reusable and maintainable control software, a good modeling tool is required. Petri nets are such a tool. Which facilitates analysis of behavioral properties, performance evaluation, and systematic construction of discrete event simulators and controllers. In this thesis a system with one robot and five sequential work …

Viscoelastic Effects On Parallel Flow Stability, Transition To Turbulence, And Turbulent Flow, Michael Garofalo

Theses

The classical two dimensional theory of stability of parallel flow is extended to viscoelastic fluids. How the elasticity of the fluid affects the point of stability and determines the point of transition to turbulence is analyzed. In addition the magnification of disturbances is elucidated. This study is based on a viscoelastic constitutive equation which has been successful in predicting the experimental trends of various unsteady high shear rate laminar flows. A viscoelastic stability equation which is an extension to the Orr-Sommerfeld equation for a Newtonian fluid is derived and solved for a flow between parallel plates superimposed by a two-dimensional …

Case Study Of Assembly Defects In Manufactured Products, Michael J. Withka

Theses

Design for Quality Manufacturability (DFQM) is a design tool that empowers engineers to create designs that are easily and effectively transformed into manufactured products. The goal of this methodology is to make designers aware of design characteristics that may lead to product defects during the assembly process. Acknowledging the possibility of these defects will enable the designer to institute design modifications early in the design phase. The benefits realized in this approach are a reduction in the number of defects in the finished product, reduced product cycle times, a reduction in monitoring costs and a reduction in time-to-market.

This thesis …

Ultra-Thin Silicon Wafer Bonding, Diyu Yan

Theses

In this thesis the history and recent developments on the silicon direct bonding technique are reviewed. The growing applications of this technique in SOI, SOS and MEMS areas, difficulties and disadvantages of various bonding processes are discussed. A direct bonding procedure for attaching ultra-thin wafers less than 200 μm thick to substrate wafers is developed and described in detail. Difficulties in handling, aligning and annealing ultra-thin wafers are reported. Wafers of different doping concentration, thickness, surface roughness and chemical characteristics are tested for bondability. Methods to minimize voids and other failure mechanisms are proposed. A photodetector is designed based on …

Microaccelerometer With Mechanically-Latched Memory, Zhenyu Ma

Theses

A new mechanically-latching micromachined accelerometer is designed in this thesis based on the large deflection of a microcantilever beam. This surface micromachined device moves in the plane of the substrate surface. This device is surface micromachined with no backside etching needed. The interaction of the friction tether and the dimensions of the cantilever beam have been modeled and calculated. The design acceleration sensitivity range is from 100G to 1000G. The photomask set has been designed by using the Mentor Graphics system. The dimension of individual accelerometers ranges from 100 to 1000 micrometers in length to tens of micrometers in width. …

A Systematic Approach To Defense Diversification, Sathappan Venkatachalam

Theses

The decline in defense spending has resulted in defense dependent companies seeking new markets through re-designing existing products, developing new products and restructuring their businesses. Defense diversification is defined as the process of transitioning a defense company's core capabilities (technologies, products, services) into commercial and non-Department of Defense government markets. A combination of site visits and review of the literature on defense diversification demonstrates the need for diversifying companies to adopt a systematic approach.

A concurrent new product development/product redevelopment model is proposed, based on the principles of concurrent engineering. The model consists of an eight phase development cycle and …

Single-Axis Agonistic Motion Control System With Electro-Magnetic Actuators, Alexander Rokhvarg

Theses

A novel single-axis motion control system using solenoid electromagnet actuators is built and successfully controlled using a non-linear real-time control algorithm. Procedures for defining and modeling the electromagnetic actuator are established and implemented. Discrete-time nonlinear control law with global asymptotic stability and zero steady-state error is designed and numerically optimized. Stable operation with small-signal 0dB crossover frequency of 370 Rad/sec and positioning RMS steady-state error of better than 4 micron is achieved. Time domain parameters are verified on a working prototype. A step reference response positioning a 0.35 Kg mass payload over 1 cm travel in under 30 milliseconds is …

The Cyberspace Workplace : An Argument And Design For The Virtual Office, Richard C. Jones

Theses

The Virtual Office has become a viable solution to the need for a changing workplace. Technology, design, and a redefinition of work have combined to create something entirely new. An office not of walls and doors but of electronic peripherals, networks, and global digital communication. This concept allows workers to be free from their physical surrounding to conduct work from remote locations or in some instances in a totally electronic world commonly referred to as Cyberspace. Through research, interviews, and problem solving the virtual office concept presented will redefine the use of space as we know it. These concepts will …

Silicon Optical Fiber Pressure Sensor, Jian Pan

Theses

A novel optical fiber pressure sensor based on a micromachined thin silicon diaphragm is proposed. Detail descriptions of the sensor structure, modulation principle and fabrication process are given.

The device operates on the following principle: Pressure deflects a silicon diaphragm which moves the output end of a light source fiber. The emitted light intensity is picked up and shared by two receiving fibers placed side by side. The variation of the intensity ratio in the receiving fibers caused by the relative motion of the emitting fiber can be easily converted to a linear signal versus the deflection of the silicon …

Heart Rate Variability Studies On Ambulatory Subjects Using Ekg Derived Respiration, Xiaorui Tang

Theses

Power spectral analysis of heart rate variability (HRV) provides a powerful non-invasive too] for exploring the balance between sympathetic and parasympathetic components of the autonomic nervous system. In the spectrum of HRV, there are three distinct peaks. The high frequency (HF) band (0.15 to 0.4 Hz) is correlated with parasympathetic activity and this is the band of interest 'in the study.

Two OTOUPS Of SL113jeCtS were considered in this work, stroke survivors and subjects performing an oral presentation in front of an audience. Data were collected with a Holter monitor to allow for ambulatory recording. Respiration was derived from the …

Time Domain And Frequency Domain Analysis Of Myoelectric Signals During Muscle Fatigue, Rakesh M. Maniar

Theses

Spectral analysis of the EMG signal is a useful tool for studying the complex phenomena of fatigue. The spectral parameters of mean frequency and median frequency, and the time domain parameter of root mean square have been used to measure localized fatigue.

The normal values of median frequency and its decline with fatigue have not as yet been determined in healthy subjects. This should be done in order to apply spectral analysis for clinical evaluations of abnormal populations. Normal median frequency values and its slope were established in this work for the upper extremity muscles of biceps, triceps and deltoid …

Simulation Study Of Particle Tracking System, Prashant B. Patel

Theses

A particle tracking system is being developed in the Particle Technology Laboratory of the Mechanical Engineering Department, at NJIT, In this thesis, an attempt is made to understand the effect of various parameters on the errors in the computed position and orientation of the sphere being tracked. Simulation results for a single transmitter assembly as well as a three transmitter assembly with 6, 9 and 17 antennae are presented. The effects of the level of noise in the voltages on the solution for the single transmitter assembly and three transmitter assembly are discussed. The concept of virtual antenna is introduced …

Scheduling Of Flexible Manufacturing Systems With Automated Guided Vehicles Using Petri Net Models, Hua-Sheng Chiu

Theses

In this thesis, Petri net models for Flexible Manufacturing Systems (EMS) are constructed. A firing sequence of the Petri net from the initial marking to the final marking can be seen as a schedule of the modeled FMS. By using the branch-and-bound algorithm, an optimal schedule of the FMS can be obtained.

Automated Guided Vehicle Systems (AGVS) are increasingly used for material handling in factories and warehouses. An AGVS can reduce labor costs and is ready to be integrated into an automated factory. This thesis presents two AGVS models (shared and duty) which integrate the control of AGVS with the …

A Three Stage Large Dynamic Range Automatic Transimpedance Control Amplifier, Karim Joseph Sikias

Theses

Long haul fiber optic communication systems require extremely sensitive, low noise amplification of the weak photo diode currents generated by the received light power. Two types of amplifiers have been used for this application: a high input impedance integrating amplifier/differentiating equalizer combination or a transimpedance amplifier. Optical receivers designed with integrating amplifiers exhibit severe low frequency drift and overload problems and are not generally used in wide dynamic range receiver design. This thesis will describe an extremely wide dynamic range transimpedance amplifier incorporating unique methods to maintain stability, wide bandwidth low pulse width distortion during overload conditions.

Soft Decision Adaptive Multiuser Cdma Detector For Asynchronous Awgn Channels, Frank Viehofer

Theses

A multiuser detector in an asynchronous, additive white Gaussian noise, codedivision multipleaccess (CDMA) channel is proposed and analyzed. It employs a combination of a decorrelator and a nonlinear multiuser interference canceler that utilizes soft tentative decisions. The weights of the canceler are adaptively adjusted, in a manner that renders the knowledge of received signal energies and the use of training sequences unnecessary. The steady state error performance of the detector is obtained and found to be superior to the performance of the same detector that utilizes hard tentative decisions.

Stress-Strain Behavior Of High Strength Concrete Cylinders, Danqing Chen

Theses

Due to the recent development of high strength concrete in engineering and construction, it has become more important to study the behavior of materials in structures.

No results have been previously published in the literature regarding the influence of aspect ratio in plain high strength concrete cylinders on stress-strain behavior under uniaxial compression.Thus at present study, compression tests were conducted on 3x6 in., 3x9 in., and 3x12 in. plain high strength concrete cylinders to study their stress-strain behavior. Plain normal strength concrete cylinders were also tested and used for comparative study.

Based on the present investigations, attempting to obtain a …

Aeration And Operation Of An Immobilized Cell Oxidative Bioreactor, James Joseph Woods

Theses

The primary purpose of this work is to help define the optimum window of operations for an immobilized cell oxidative bioreactor. The analytical technique employed requires no outside verification (such as G.C. analysis) and is independent of liquid flow rate. Method of aeration has been determined to be an important parameter for optimizing bioreactor efficiency, and optimization of the quantity of hydrogen peroxide added to provide oxygen during bio-oxidation has been investigated. Ammonium hydroxide as a fixed nitrogen source can be used to restore the vitality of the bioreactor under certain conditions.

The effects of several different methods of providing …

Quantitative Studies Of An Immobilized Cell Oxidative Bioreactor, Timothy Lance Borkowski

Theses

The purpose of this work was to determine a suitable method of utilizing dissolved oxygen in reservoir solution data to quantitatively measure the amount of oxygen and substrate consumed for an immobilized cell batch bioreactor in a recirculation configuration. Statistical analysis was performed on multiple phenol injections to determine the mathematical relationship between dissolved oxygen readout and the amount of phenol degraded.

Factors considered in the mathematical analysis include amount of substrate degraded, reaction time, recirculation flow rate, measured dissolved oxygen concentration and oxygen consumption, oxygen conversion per pass through the bioreactor during steady state, and vitality of the microorganisms. …

Implementation Of Time-Frequency Distribution Software And Its Use To Study Biological Signals, Mansour Adib

Theses

The joint time-frequency signal representation has received considerable attention as a powerful tool for analyzing biological signals. It combine time-domain and frequency-domain analyses to yield a potentially more revealing picture of the temporal localization of a signal's spectral components. In this research we have developed algorithm which implement time-frequency signal analysis techniques on a computer system. Its primary function is to produce a variety of time-frequency representations and plots from the time series. Numerous generated signals were used to justify our computer algorithm.

Variety of time-frequency distribution were utilized to expand the concept of spectral analysis of heart rate variability, …

Use Of Multiple Transmitters For 3-D Non-Intrusive Particle Tracking, Jitesh H. Agrawal

Theses

A method for non-intrusive tracking of a particle in 3-dimensional space, based on processing of signals emitted from a transmitter embedded in the particle, is being developed. This method uses a mathematical model, which predicts the induced signal in receivers present in the vicinity of flowing particle, and supporting numerical techniques. Specific application aspects related to improving the accuracy of this method are presented.

The focus here is the development of flexible software capable of processing information coming from multiple transmitters with known distinct spatial orientation. Implementation aspects of modified existing empirical corrections for improving model-reality agreement, and new techniques …