Digital Commons Network^™

Correlation Between Drying Times Of A Vinyl Copolymer Solution And Properties Of Dried Films., Abd El-Rahman M. Naser

Masters Theses

"One of the common methods used in film formation is the solvent evaporation method. As the evaporation starts the viscosity increases due to the inability of the solvent to keep the chains apart, which leads to a drag between molecules.

The rate of evaporation of the solvent (loss of solvent) cannot be equated with the rate of drying, since the latter depends on the results of the loss of solvents in terms of viscosity and plastic properties. The drying time can be defined as the rate at which a film increases its viscosity and thus changes the properties of a …

The Prediction Of The Viscosity Of Multi-Component Non-Polar Gaseous Mixtures At Atmospheric Pressure., Gary D. Fehsenfeld

Masters Theses

"The applicability of the Strunk, Custead, and Stevenson method for predicting the viscosities of multicomponent, non-polar, gaseous mixtures vas investigated. The viscosities of 24 ternary and quaternary gaseous mixtures were experimentally determined, at 3 temperature levels, and compared with the corresponding calculated viscosities resulting from the prediction method. In addition, the published viscosities of 64 multicomponent mixtures were compared with the corresponding calculated viscosities.

Altogether, the viscosities of 136 multicomponent, non-polar, gaseous mixtures were compared. The mixtures contained from 3 to 7 components including 16 different gases in the temperature range from 5• to 1014 ° c, and at a …

A Rubber Membrane Analogy For The Study Of Shafts In Torsion., Myron D. Bruns

Masters Theses

"The thesis presents a review of literature giving reference to several books which present the many and varied methods of determining the shearing stresses in shafts. However, no reference was found that used a rubber membrane analogy similar to that used in th is thesis. The theory of torsion, the membrane theory, and its analogy have been presented for a better understanding of the subject. Illustrations are used freely for clarity.

Analytical methods and solutions are given for two problems. The first method is that of writing a Saint-Venant stress function and satisfying the necessary conditions for it to be …

Use Of Sr-4 Strain Gages Under Hydraulic Pressure, Manubhai M. Patel

Masters Theses

"In this investigation an attempt has been made to determine the effects of hydraulic pressure on SR-4, type A-5 strain gages. A thick-walled aluminum alloy cylinder without end constraint was used to make an experimental study of the effects of hydraulic pressure on these strain gages.

The behavior of this cylinder under different internal hydraulic pressures was also studied by measuring the strains by means of strain gages which were attached to the inside and outside surface of the cylinder. The problem has been studied by applying pressures up to 4800 psi.

Because of the high internal fluid pressures various …

The Design, Construction, And Operation Of A Conducting Field Analog Computer., Richard T. Johnson

Masters Theses

"The purpose of this investigation is to design and construct a simple conducting field analog to solve problems described by the two-dimensional Poisson or Laplace equations. Decisions concerning choice of conducting media, construction of problem models, and design and construction of a specialized power supply with instrumentation were based on the results of previous experiments. Several problems are solved using the designed apparatus. Partial solutions to these problems are displayed in graphical form.

The greatest deviation of the experimental results from iterative values was consistently less than 8%. In most cases the deviation was less than 6%. The console arrangement …

A Study Of Rotational Critical Speeds For A Multi-Mass System By Influence Coefficients, Kantikumar G. Patel

Masters Theses

"In this investigation an attempt has been made to determine the critical speeds of a multi-mass rotational system by using influence coefficients. Modes of vibrations are also examined at these critical speeds.

A shaft carrying five masses, supported by bearings at the ends, has been studied analytically. The length of the bearings is considered small with respect to the shaft length and therefore, the configuration is assumed to be point supported as a simple beam. The five masses, each weighing one pound, were placed at equal distances of 10 inches on a 60 inch shaft. The critical speed was examined …

The Effect Of Metallic And Inert Electrodes On The Electrochemical Degradation Of Alkyl Benzene Sulfonate., Thomas Patrick O'Farrell

Masters Theses

"The purpose of this study was to investigate the effects of various metallic and inert electrode combinations on the electrochemical degradation of alkyl benzene sulfonates (ABS) in water and to determine the rate and degree of AB3 removal.

Selected combinations of copper, aluminum, iron, and carbon plate electrodes were studied in systems of tap, distilled and river waters containing an initial ABS concentration of 10 mg/1, using a current density of approximately 0.5 milliamperes per square centimeter and a total detention time of 6 hours. Samples were collected at appropriate time intervals and were analyzed for ABS, chemical oxygen demand …

Minimum Frictional Characteristics Of Optimum Journal Bearings., Navinchandra F. Shah

Masters Theses

"This investigation was conducted to develop a graphical representation to determine the optimum bearing conditions for minimum friction and to establish a theoretical approach for journal bearing design.

A series of graphs has been plotted for· the coefficient of friction versus the eccentricity ratio based on the. Sommerfeld number derived from Reynolds' differential equation, f or optimum journal bearings.

The results obtained in this research have been compared with those developed by other investigators. This comparison confirms the validity of the results presented in this thesis, so that it could be used advantageously for the design of optimum journal bearings"-- …

Stability Investigation Of Pipe-Line Suspension Bridges, Ten-Hsi Chen

Masters Theses

“This thesis presents an analysis of the behavior of pipe line suspension bridges under the action of wind. From this analysis a differential equation of vertical vibration is derived and solved, and the possible methods of preventing its vibration are discussed and suggested”--Abstract, page ii.

Federal – Local Relations: A Case Study Of The City Of Kalamazoo In 1962, Glen L. Bachelder

Masters Theses

Purpose and Scope

It is the purpose of this paper to study the impact of federal government aid on Kalamazoo, Michigan in 1962. As a setting for the case study information, the development of federal aid programs as they affect municipal governments in the United States will be explored. The case study approach was selected since the bulk of material now available on the subject deals with the programs as viewed from the National Government level or as applied to the fifty states. Thus the idea of a detailed look at just one city as a recipient of federal aid …

Factors Which Caused Changes In The Marketing Practices Of The Sutherland Paper Company In The Period 1950-1960, Leslie C. Eaton

Masters Theses

Introduction

The purpose of this paper is to examine and discuss changes in the marketing practices of the Sutherland Paper Company during the period from 1950 to 1960.

In order to examine and discuss the changes which have taken place it is necessary to examine the history of the Boxboard Industry and the Company to set the scene in its proper perspective.

Folding cartons have become very much a part of our lives, our culture, so that they are quite taken for granted much as we take our use of electricity or running water for granted.¹

In their daily …

An Investigation Of Creative College Students Using Two Measures Of Flexibility, John L. Roberts

Masters Theses

No abstract provided.

The Harmony Society In Indiana, George Augustus Turner

Masters Theses

No abstract provided by author.

Digital Computer Design Of Compensation For Linear Control Systems, Larry C. Amsler

Masters Theses

"If a control system is to be synthesized, it is inferred that a plant or process is present which must be controlled, and the problem of how to design the control system then arises. The first step is to decide on performance specifications to which the complete system must conform. These specifications may involve such things as the system steady state response, transient response, or frequency response. Any of several synthesis methods may then be applied to complete the system design.

In this study a synthesis method is developed for single-loop linear feedback systems. First, the number of compensating poles …

Permeation Of Water Vapor Through Linear Polymer Films, Mohammed S. Rifai

Masters Theses

"Film formation from thermoplastic resin solutions Is Influenced by secondary intermolecular forces. Consider what may happen when organic coatings change from a liquid to a solid state. In the liquid state it is logical to consider the linear polymer molecules as agglomerates being dispersed in the volatile component rather than being present In solution. These molecular agglomerates are referred to as micelles. They have various degrees of orientation depending on the extent and the location of dipole forces in both polymer and solvent molecules.

When a coating is applied the solvent starts to evaporate and the micelles are driven closer …

A Study Of The Haeffner Effect In Mercury, James Nicholson Baysden

Masters Theses

"In 1953, E, Haeffner reported that when he passed a direct electric current through a capillary tube filled with mercury, he obtained a separation in the isotopes of mercury with the heavier isotopes being enriched at the negative terminal and the lighter isotopes at the positive terminal. This effect has since been referred to as the Haeffner Effect, Since the original experiment with mercury, other investigators have observed this effect in many other liquid metal systems.

This investigation of the Haeffner Effect in mercury involves the use of a radioactive isotope of mercury (Hg 203) as a tracer to follow …

Thermocouple Shape Influence On Response In A Dynamic Compressible Fluid Atmosphere, Philip J. Steger

Masters Theses

"This investigation was performed to determine whether the geometrical shape of a thermocouple used to measure the temperature of a dynamic fluid atmosphere had any affect on its recovery factor and time response.

A converging nozzle was used to establish a dynamic fluid stream in which shaped silver solder junctions of copper-constantan thermocouples were tested. The velocity of the working fluid, air, was about 1000 ft/sec at the test point.

The investigation was successful, within experimental limits, in determining that the recovery factor of a bare thermocouple junction is not influenced by geometrical shape The results agreed substantially with available …

A Preliminary Study Of The Dielectric Properties Of Bismuth Ferrate Ceramics., John Joseph Schwaller

Masters Theses

"In this investigation some of the results of Fedulov¹⁸ for a composition of 30 percent lead titanate - 70 percent bismuth ferrate were verified. The system of lead zirconatebismuth ferrate was studied with sintering data determined for the series. By X-ray and microscopic analysis the system was determined to be not a solid solution. The dielectric measurements show a linear relation between the dielectric constant and the percent lead zirconate from 100 percent BiFeo₃ to 10 percent BiFeo₃ - 90 percent PbZro₃"--Abstract, p. ii

Investigation Of Stresses And Deflections In An Inclined Beam., Jayant Chhaganlal Soni

Masters Theses

"In this thesis an investigation has been made of the effect of inclination on strains and deflections in an inclined rectangular steel beam. To compute the strains and deflections Newmark's Numerical Procedure has been used. An experiment has been carried out on a rectangular steel beam for four different load increments and eight different inclinations. To compare the experimental and analytical data, graphs have been drawn for the experimental and analytical quantities of strains and deflections for all the four load increments and eight different angles of inclination. Results of the investigation indicate that the strains and deflections at inclinations …

A Study Of A Method For Determining Properties Of Metals At High Strain Rates., Warren Heidbreder

Masters Theses

"An experimental method has been developed for determining the tensile and other physical properties of metals under high loading rates. Experimental equipment was designed, fabricated and tested. It was desirable to keep the equipment simple and inexpensive so that it could be used by operators Lacking experience in electronics and high-speed photography which are required for some of the more sophisticated methods now in use. The energy for pulling the specimens is supplied by smokeless gun powder. The firing of a cartridge into a closed cylinder with movable piston accomplishes the breaking of the specimen. A record of the time, …

Dissolution Rates Of Zone Refined Iron And Steel In Hydrochloric And Sulfuric Acids And In Sodium Chloride Solutions., Gary E. Welch

Masters Theses

"Dissolution rates for two carbon steels were deter­ mined in four concentrations of sulfuric acid at five temperatures and in four concentrations of hydrochloric acid at four temperatures.

No general relationship was found for the variation in activation energies in sulfuric and hydrochloric acid. An explanation of the difference in the reaction rates and a possible explanation of the activation energy is presented on the basis of chunk formation.

The results of this investigation indicate an electrochemical control mechanism for the dissolution reaction of steel in acid solutions.

Results of dissolution rate studies in sulfuric and hydrochloric acid solutions and …

The Performance Of A Mechanically-Aided Countercurrent Extraction Column., Jerry James Carr

Masters Theses

"In recent years liquid extraction has become a major industrial method for the separation of liquid solutions. Liquid extraction has proven successful in some separations performed only with great difficulty by other, more common mass-transfer operations. Th e industrial utilization of liquid extraction has resulted in considerable interest in the design and performance correlations of high-capacity, high-efficiency extraction equipment.

Continuous countercurrent columns, filled with various packings, baffles, and plates, have been found to be relatively ineffective in liquid extract on service. The density difference of the contacted phases is generally insufficient to, by itself, cause the intimate contact necessary for …

Hydraulic Transportation Of Coal In Open Flumes., Nallapu Narayan Reddy

Masters Theses

"The objective of this study is to design a simplified form of hydraulic transportation system using open-flumes and operated by gravity in pitching coal seams. This type of system is to be used in conjunction with mining by hydraulic methods where the water used for the extraction of coal can also be used for the loading and transport functions"--Introduction p. 1

Electrolytic Corrosion Of Reinforcing Steel In Concrete., Lawrence D. Green

Masters Theses

"Deterioration of bridge decks has increased the interest in the corrosion of steel in concrete. A comprehensive review of literature on the subject of electrolytic corrosion of steel in concrete is presented in this thesis.

Development of theory from the literature leads to the following statements. There are two causes for electrolytic corrosion of steel in concrete, stray currents from direct current power sources and the formation of macro-cells within the structure. The corrosion caused by the macro-cells appears to be the more important of the two. Anodic areas exhibit corrosion of the steel and cracking of the concrete.

Many …

Determining Stability Of Nonlinear Control Systems Via Lyapunov's Method., John Joseph Komo

Masters Theses

"The problem undertaken in this thesis is to present Lyapunov's method of stability as i t applies to control systems and to use it in the stability analysis of nonlinear control systems. The variable gradient method of generating Lyapunov functions is presented since this seems the best general procedure for obtaining Lyapunov functions. Also, the integration of matrices method is presented as a comparison. ii

Procedures for the use of the variable gradient method and the integration of matrices method are written and several examples are used to illustrate these procedures.

It is concluded that Lyapunov's method is very definitely …

Viscosities Of Various Binary Non-Polar Gaseous Mixtures., Gerald Lee Stevenson

Masters Theses

"Viscosity is an important physical property involving the transport of momentum in a fluid. Momentum is transferred within a fluid under an existing velocity gradient as the driving force. Since momentum transfer is actually attained by the dynamic interaction between particles of mass, a description of molecular interaction is essential in order to accurately predict the viscosity of a fluid. Temperature affects fluid viscosity by increasing the kinetic energy of the fluid system and thus the frequency by which molecules are involved in interaction. There have been many theoretical studies made concerning the intermolecular potential energy statements which serve as …

Swelling Properties Of Putnam Soil, Oscar M. Palma

Masters Theses

"Volume change of Putnam soil under different moisture contents and the swelling pressure developed by the soil at the same moisture contents were investigated using standard test procedures.

The theory of one dimensional consolidation of Terzaghi was reviewed as well as the literature on swelling and swell pressure.

It was found that swell depends mainly on the initial water content, while swelling pressure depends mainly on the dry density of the soil"--Abstract, page ii.

Liquid Mercury Embrittlement Of Thin-Walled 2024 Aluminum Tubes, Edward J. Beckemeyer

Masters Theses

"The dislocation theory, Zener-Stroh crack model, and the Petch relationship, which correlates fracture stress and grain size, were used to analyze the embrittlement of 2024 aluminum alloy tubes by liquid mercury.

Surface energy ratios, [formula], were determined for biaxial stress ratios of 1/2, 1, ∞. The values of the surface energy ratios considered were 4.24, 1.79, 1.46, respectively. As part of this study, an approximate Nabarro-Peierls frictional stress was calculated for each stress ratio"--Abstract, page 2.

An Investigation Of A Constant Velocity Paper Unwinding Device, Jerry L. Gilmore

Masters Theses

"This thesis outlines one approach in designing a system which involves a second order nonlinear differential equation. A large number of variables are involved in this analysis. Therefore, there are many solutions to the problem but only a few of these will satisfy all required conditions. The analysis will be aided by the use of an analog computer. This computer can be manipulated to obtain optimum values for the different variables.

The computer results are presented in graphical form. Reasonable values for the different variables are obtained from these graphs.

The characteristics of the unwinding device were simulated on the …

Analysis Of Problems In The Performance Of A Natural Gas Storage Reservoir., Gerald Eugene Henderson

Masters Theses

"A digital computer technique is presented for predicting two parameters of underground natural gas storage reservoir performance: (1) the prediction of reservoir pressures and volumes, and (2) the prediction of optimum flow rate and pressure drawdown for a single well in accordance with the theory of water coning.

The outlined procedure for predicting gas storage reservoir pressures and volumes was not effective for the field studies, although certain conclusions have been drawn which should be beneficial in further studies.

The procedure for predicting optimum gas flow rate and pressure drawdown from a well without production of bottom water involved first …