Digital Commons Network^™

Studies Of An Electrical Method For Generating Ultrasonic Waves, Yung-Yien Huang

Masters Theses

“Ultrasonic waves have proved very valuable in the observation of both the velocity and the absorption coefficient of sound in various media. From the velocity measurements of ultrasonic waves in metals, it is possible to obtain elastic constants, such as the compressibility, and the specific heat. Also, the observed attenuation depends greatly on the type and structure of the material. One of the widely used methods for investigation of the internal losses in solid state physics is the pulse-echo technique. This method is being used almost exclusively in internal friction investigation"--Introduction, page 1.

Estimating Bench Design Parameters For Open-Cut Excavation, Rajni K. Gandhi

Masters Theses

"There are no direct relationships available that provide a basis for bench design of multiple-bench, open-cut earth excavations in competent materials when power shovels are employed. This study was undertaken to determine if mathematical design expressions could be developed when the production rate, material's properties, and equipment operating characteristics were known.

It was found that all bench dimensions were a function of the bench height, which in turn was controlled by the required rate of production. The investigation revealed that suitable relationships could be developed to guide in the control of bank stability, choice of shovel capacity, determination of the …

The Anodic Dissolution And Disintegration Of Gallium And Aluminum And The Initial Valency Of The Ions Entering Aqueous Solutions., Kenneth Anderson Poush

Masters Theses

Gallium dissolved very slowly in dilute acids like HC1, H₂SO₄and HCIO₄. The rate was substantially accelerated if the metal was connected with a platinum electrode in the same solution. From the volume of the hydrogen developed the trivalency of gallium ions going into solution was calculated. This same ionic charge was obtained from coulometric measurements using gallium-amalgam as the anode. The initial ionic charge of aluminum dissolving from an aluminum amalgam anode was evidenced as being plus three by coulometric measurements.

Gallium and aluminum anodes were found to partially disintegrate while the current flowed. …

Optimalization By Peak-Holding, Curtis W. Dodd

Masters Theses

"The problem presented is a study of the peak-holding method of optimalization. This method applies to a system that has an extremum.

After describing how the complete system, consisting of the controller and the controlled system, works; variations in the controller are presented. These variations are changes in the final stage of the controller, the servo. A phase-plane analysis shows how the output of the controlled system varies with its rate of change. Limitations are presented which tell why the system cannot be kept at its peak value at all times. Finally an analog simulation is used to study the …

Properties And Perfection Of Zr-H Solid Solutions At Room Temperature., Dirk Heinrich Wiebe

Masters Theses

"The lattice constants of α. - Zr with 122 ppm H are a₂₅ = 3.23622 ± o. 00005 Å and c₂₅ = 5 .1526 ± 0. 0003 Å. The thermal expansion coefficients of α - Zr are found to be α_a =4.6 x 10^-6(⁰C^-1) and α_C =11,0 x 10^-6(⁰C^-1) in the range between 15 and 55°c.

The solid solubility limit in the Zr - H system at room temperature and independent of the H pressure was determined by the parametric x-ray method to be …

Solid-Phase Welding Of Nodular Iron To Low Carbon Steel., Scott H. Carriere

Masters Theses

“This paper presents an experimental investigation of the possibility of using solid-phase welding to join nodular iron to low carbon steel. Included is a review of available literature on solid-phase welding, tracing its origin from early Egypt to the present day. There was no previously reported work found on the welding of nodular iron to steel.

Experiments were performed to determine what temperature-pressure combination gave the greatest ultimate tensile strength These experiments resulted in the best welds being produced with an end load of 7000 pounds (35.700 psi) on a half inch diameter sample. The majority of these welds proved …

The Effect Of Gap Graded Aggregate On The Properties Of Hot Mix Asphaltic Concrete, Maurice L. Northcutt

Masters Theses

"The objective of this investigation was to determine the effects of deviations from the recommended gradation of aggregate upon asphalt concrete mixes. The aggregate used in this study was a good grade Missouri Limestone and was mixed with an asphalt cement of 85-100 penetration grade. A control mix was designed in accordance with the Marshall Method using a gradation recommended by the Asphalt Institute. Ten aggregate blends were prepared by wasting certain fractions or combinations of fractions and the wasted weights were redistributed into the coarser or finer aggregate sizes. The test mixes were designed using the same method and …

The Importance Of Radiation As A Means Of Controlling Surface And Internal Temperatures Of A Semi-Infinite Solid, Kenneth C. Woodruff Jr.

Masters Theses

"This problem is concerned with the temperature history of a semi-infinite solid bounded by one flat surface.

Heat was applied by convection from a hot fluid to the flat surface of the solid which was originally at a uniform temperature. Heat was radiated from the flat surface to black space and conducted into the solid according to Fourier's law. The temperature at the surface, and at several points beneath the surface, was determined as a function of time.

A method for solution of such a problem is demonstrated here by the use of numerical analysis and the Royal McBee LGP …

Study Of Mass Transfer In Oscillating Droplets., Subhash Vishnu Gangal

Masters Theses

"The object of this investigation was to study the resistance to mass transfer inside single oscillating liquid droplets falling in a liquid medium. The following four systems were studied: (1) 3% acetic acid in nitrobenzene and water, (2) 25% acetic acid in nitrobenzene and water, (3) 3% acetic acid in nitrobenzene and glycerin in water, and (4) benzyl alcohol and water. The individual mass transfer coefficients were computed by using the Handlos and Baron relation and were compared with the experimentally determined dispersed phase mass transfer coefficients. The average absolute deviation of the observed values of dispersed phase mass transferred …

Investigation Of The Effect Of The Wall Thickness On The Residual Stresses Developed In Thick Wall Cylinders Due To Water Quenching From The Outside Surface., Ghanshyam Chandubhai Patel

Masters Theses

"This investigation has been made to determine the residual stresses in thick wall cylinders by the use of strain gages.

The cylinders were quenched from their outer surface i n water from a temperature of 1000°F, and the resulting residual stresses were determined by Sachs boring-out method. The effect of the wall thickness of the cylinders on the residual stresses and the error developed due to the boring operation were discussed"--Abstract, p. ii

Determination Of The Shapes Of Fixed And Moving Polodes Of Class Ii Four Bar Mechanisms., Manharkumar Kantilal Sheth

Masters Theses

"The purpose of this thesis is to determine the shapes of fixed and moving polodes of class II four bar mechanisms, since there has been little, or no work done in determining their shapes.

Twenty different mechanisms were taken to study the shape of the fixed and moving polodes. The best equation which fits each curve was found by using the least square method in polynomials. Coefficients for each curve were determined with the help of the I.BM 1620 computer. The equation was found to be a six-degree polynomial which fits very well to each curve. There seems to be …

Densification Studies Of Three-Component Refractory Grog Systems., Jerome Dale Patterson

Masters Theses

"The bulk density and crushing strength properties of three-component refractory grog systems that were formed by mechanical impact or by mechanical vibration were determined.

Aqueous alkali silicate solutions of various types, concentrations, and amounts were investigated as room temperature binders for these grog systems. Compositions having maximum bulk densities were determined for each of six different three-component refractory grog systems. The densification rate curves for systems formed by mechanical impact were determined"--Abstract, p. ii

The Effects Of Surface Flaw Density And Configuration On Fracture Stresses Of A Triaxial Porcelain., William H. Daniels

Masters Theses

"The fracture behavior of a model brittle solid containing artificial surface flaws was studied. An industrial ceramic porcelain body was employed as the model brittle material. Sample groups of specimens containing 6, 11, 24, 49,. and 90 sharp surface notches uniformly distributed over a four inch length were broken under pure bending. The fracture data we-re compared to those of an identically treated control group containing no artificial flaws.

The mean strengths of the two groups of lowest flaw density were identical, both being significantly less than that for the control group. Further increases in flaw density resulted in increased …

A Determination Of The Theoretical Stresses In A Deep Beam., James William Tritz

Masters Theses

"This paper presents an analytical solution of the stress distribution in a deep beam of finite length. The beam being considered is analyzed as one of plane stress. The method employed superimposes two stress functions each of which is a trigonometric series. The first stress function satisfies all boundary conditions except that of zero stress on the vertical faces. The second function is found, so that, when combined with the first function, all boundary conditions are satisfied. The IBM 1620 digital computer is then used to find the stresses for a particular beam. The results of this analysis are then …

The Prediction Of The Thermal Conductivity Of Various Binary Non-Polar Gaseous Mixtures., Chester Foon-Chen Feng

Masters Theses

"A simple method for predicting the thermal conductivity of binary non-polar gaseous mixtures from the force parameters of the pure components and composition was developed. The method is an extension of the application of the combining methods previously derived for viscosity predictions. Altogether, the published thermal conductivities of 683 binary non-polar mixtures at various temperature levels were compared with the corresponding calculated thermal conductivities resulting from the prediction method. The corresponding values predicted from Hirschfelder, Curtiss and Bird's expression were also compared.

Among the 683 binary mixtures, there were 138 di-di, di-poly, and poly-poly mixtures, 241 mono-

Influence Of Quartz Particle Size And Concentration On The Fracture Stresses Of Triaxial Alumina Porcelain., John David Weyand

Masters Theses

"Quartz particles were introduced into a typical triaxial alumina porcelain. Three levels of particle size and three levels of concentration were studied. The strength sample sizes were large. A diametral- compression loading method was used for strength testing. It was found that the porcelain strength decreased with increasing grain size and concentration of quartz particles. A linear relationship existed between log quartz concentration and mean fracture stress"--Abstract, p. ii

Application Of An Orifice Meter To Fan Testing., J. F. T. Agapito

Masters Theses

"In this investigation the application of an orifice meter to fan testing was studied and evaluated. An orifice meter was designed and was installed in a centrifugal fan duct. Measurements were checked and compared with those of a standard pitot-tube traverse and were found to be in very close agreement. It is suggested that a meter of this type could easily be adapted not only to laboratory work but also to field tests"--Abstract, p. ii

Solid Solubility Of Sodium Oxide In Tricalcium Aluminate, Joel A. Conwicke

Masters Theses

"The tie line connecting the compounds 3CaO·Al₂O₃ and Na₂O·8CaO·3Al₂O₃ in the ternary system CaO-Al₂O₃-Na₂O was studied at 1250° Celsius.

It was determined that Na₂O can exist in crystalline solution with 3CaO·Al₂O₃ in percentages of about 2.3% or less without any apparent change in the structure of 3CaO·Al₂O₃. X-ray diffraction peaks in the back-reflection region shifted to lower d-spacing values on increasing Na₂O contents.

At a Na₂O content of about 2.7%, each major x-ray …

A Study Of The Separation Of A Mixture Of Carbon Dioxide And Hydrogen By Means Of An Orifice., Larry Gene Bauer

Masters Theses

"The purpose of the investigation was an attempt to verify a statement made by Partridge in an effort to discover a new method of separating gaseous mixtures. Partridge stated that when a constant pressure is applied on two gases of different specific gravity, a larger volume of the l igl1ter gas is forced through the orifice. Orifices of 1.016, 0.319, and 0.222 millimeter in diameter were used in the course of the investigation.

It was found that with the apparatus used in the research endeavor, no separation of the mixture of hydrogen and carbon dioxide could be obtained"--Abstract, p. i

A Study Of The Stabilization Of Putnam Silt Loam With Large Organic Cations, George C. Bennett Jr.

Masters Theses

"Laboratory tests were conducted to determine if Aliquat, a quaternary ammonium chloride compound, could be used to change the physical properties of Putnam silt loam. The effects of adding varying amounts of Aliquat to the soil were measured in terms of the results of Atterberg limits tests, the moisture-density relationship, unconfined and triaxial compressive strength, and capillary adsorption characteristics. A small change in the Atterberg limits, the optimum moisture content, and the maximum dry density was noted. An increase in the unconfined compressive strength and a reduction in the moisture adsorption potential was accomplished by the addition of 0.25 and …

The Effect Of Surface Roughness, Cure Pressure, And Temperature Level On The Thermal Resistance Of Bonds And Contacts, David Leo Schwaller

Masters Theses

"This investigation was conducted to determine the thermal effect of temperature level, surface roughness, and curing pressure on bars and bonded interfaces.

The equipment used in this investigation is shown in Fig. 1 and Fig. 2. The four specimens used, cylindrical aluminum alloy bars, were cut radially at their midpoints and faced on a lathe. Heat was supplied by an electrical resistance heating element and an ice bath was used to conduct heat from the alloy specimen. A heat shield was used to insure one dimensional heat flow. Spacers were placed in the insulation at the top, the interface, and …

Determination Of The Fast Flux Of U.M.R. Reactor, Dave Vibhakar Ratilal

Masters Theses

"Measurements of fast flux of University of Missouri at Rolla, Reactor have been made using: (n,p) reactions in Mg²⁷ and Ni⁵⁸ and (n,α) reactions in Al²⁷. The effective activation cross sections at respective threshold energies for various foils have been obtained from AERE and AECL reports and from literature published by various investigators. A RIDL 400 channel analyzer was used for counting"--Abstract, page 1.

Effect Of Hydroxyethyl Cellulose On Properties Of Concrete At Early Ages., Vipinchandra R. Shah

Masters Theses

"In this investigation, hydroxyethyl cellulose was used as an admixture in plain concrete. The admixture was tested for its effect on the compressive strength of plain concrete cylinders and for its effect on the flexural strength of plain concrete beams. Specimens were also tested for freeze-thaw durability and shrinkage.

The test results indicated that hydroxyethyl cellulose has the effect of increasing the compressive strength and decreasing the flexural strength of plain concrete. The rapid freezing and thawing tests showed that the durability increases with increase in amount of admixture.

The tests were carried out in the Materials Laboratory of the …

Determination Of Transient Temperature Stresses In Plates, Teh Yu Hu

Masters Theses

“The purpose of this thesis is to determine the transient temperature stresses in two-dimensional plate structures restrained against rotation at the ends but not restrained against elongation. In this investigation, only one-dimensional heat flow is considered. The heat flow is first treated as a problem in pure conduction and then the effects of convection through a boundary layer are considered.

The differential equation of transient heat conduction is solved by Fourier series and Duhamel’s theorem, and a graphical method of solution for temperatures in terms of dimensionless parameters is presented.

Solution of this problem is valid for a semi-infinite plate …

Effect Of Internal Pressure On Compressive Buckling Stress Of A Cylindrical Shell Under Eccentric Loading, Chao-Ping Chu

Masters Theses

“In this paper, an investigation was made of a thin- walled cylindrical shell under compressive load with various eccentricities and internal pressures to study the effect of the internal pressure on the compressive buckling stress of the shell.

So far, theoretical methods have not been devised to solve this problem; therefore, an experimental study was carried out. The experimental results indicated that the buckling load of the shell decreases as the eccentricity increases, that the buckling stress increases as the eccentricity increases, and that the change in buckling stress increases with an increase of internal pressure and is very nearly …

Nature And Lateral Variation Of Lost Rock Limestone In The Tri-State Zinc-Lead District., Adnan A. Saadallah

Masters Theses

"The nature and lateral variation of a host rock limestone in the Tri-State zinc-lead district were petrographically studied within a single horizon, the M bed. This bed is a massive crinoidal limestone in the Tri- State district of southwestern Missouri, northeastern Oklahoma and southeastern Kansas and is a part of the Mississippian Keokuk Formation.

One hundred and twenty specimens from this bed were collected underground from six pull drifts in five mines: West Side, Grace B, Big John, Little Greenback, and Mudd Mines. The specimens were collected at regular intervals, usually ten to twenty feet, beginning at the edge of …

The Effect Of Plastic Deformations On Grain Boundaries., Jayendra Jamnadas Shah

Masters Theses

"The purpose of this study is to determine the effect of the plastic deformations on the grain boundaries and the grain structure of mild steel. Five beams tested were of A-36 steel and of 6 WF 20 rolled section. Central loading was used to develop a plastic tinge at the cent1:1r.

At the center, where a plastic hinge was formed, the effect of the plastic deformations on the grain structure was severe in all the samples taken from the tension side of all plastically or partially plastically loaded beams. In fully plastically loaded beams this effect had spread on both …

A Theoretical And Experimental Study Of The Stress Distribution In An Infinite Plane Shrink-Fitted On Four Circular Elastic Pins, Charles H. White

Masters Theses

"The purpose of this study is to show a general method of solution for multiple inclusions in an infinite plane. The shrink-fitting of an infinite plane upon the inclusions, or pins, will be simulated by force-fitting the pins into a large sheet of birefringent material, to obtain an experimental verification of the analytical solution.

The problem to be approached is that of four circular elastic pins shrink-fitted in an infinite plane. The method of superposition will be used, and the stresses at any point in the plane found with respect to a common origin of coordinates. It will first be …

A Study Of Methods For Estimating Parameters In The Model Y(T) = A₁E-P₁T + A₂E-P₂T + Ε, Gerald Nicholas Haas

Masters Theses

“In this study, methods for estimating the unknown parameters A₁, A₂, p₁, and p₂ in the model
y(t) = A₁e^-p₁t + A₂e^-p₁t + ϵ
where ϵ ~ N(0, σ) are investigated. In the model investigated, A₁, A₂, p₁, and p₂ are positive.

Four methods, one non-iterative method and three iterative methods, for estimating parameters in this model are investigated. The non-iterative method is known as Prony's Method. The three iterative methods are (1) the Modified Gauss …

A Laboratory Model Study Of Fluid Cross Flow., James Gary Fore

Masters Theses

"A procedure for scaling and operating a laboratory model for the purpose of studying fluid crossflow between zones of different permeability is presented. A modified existing model is used to simulate conditions for three dimensional, incompressible, two-phase flow through a two-layer, unconsolidated, homogeneous porous medium.

Eight tests were made to show effects on crossflow between the zones. Qualitative results indicate crossflow from the high to the low permeability zone for various perforation ratios and mobility ratios"--Abstract, p. ii