Digital Commons Network^™

Modification Of The Hydraulic Jump By Submerged Jets, Edward Leon Tharp

Masters Theses

"Tests were performed in order to determine the effect of submerged jets injecting water into the base of the hydraulic jump. The jump was studied in terms of the following properties: specific energy of the flow leaving the hydraulic jump, length of the hydraulic jump, tailwater depth, and wave formation properties. These properties for the hydraulic jump with submerged jets were compared to the natural hydraulic jump.

Results of the tests indicate that: submerged jets at any angle tested tend to decrease the specific energy of the water leaving the jump and are more effective than the impulse-momentum principle indicates, …

The Anodic Dissolution Of Magnesium In Aqueous Solutions, Chen-I Lu

Masters Theses

"The anodic dissolution of magnesium was studied in MgCl₂-KC1 and MgBr₂-KBr mixtures at 25, 40, and 55 °C. The parameters of the study were current density, concentration of magnesium ion, and temperature. The concentration of magnesium ions was varied from 0.001 to 1 N holding the ionic strength constant at 1.5. The weight loss of magnesium from the electrode during electrolysis was determined by weighing the electrode both before and after electrolysis. The current was measured with a sensitive milliammeter. The range of the current densities was varied from 0.001 to 0.1 amps·cm^-2. The …

Analysis Of Sand Asphalt Mixtures, Maurice A. Sayegh

Masters Theses

"The objective or this investigation was to determine the optimum percent of asphalt which should be added to the sand asphalt mixture. Also the effects of filler on the properties or the sand-asphalt mixture were evaluated.

The variables in this study were mineral filler, asphalt cement, and asphalt content. The sand used in this study was sub-rounded, and uniformly graded. The asphalt was asphalt cement with two different penetrations, one of 85-100 penetration grade and the other of 120-150 penetration grade.

Three different groups of mixtures of sand-asphalt were prepared. The first group consisted of adding 85-100 penetration asphalt to …

Some Effects Of Sodium Pentachlorophenol On Activated Sludge And Minnows., James Albert Heidman

Masters Theses

"The primary purpose of this investigation was to determine the effect of sodium pentachlorophenol on activated sludge. An additional objective was to determine the toxicity of sodium pentachlorophenol to minnows.

All activated sludge units were grown on a glucose and mineral nutrient waste. In addition, a unit acclimated to 100 and 250 mg/1 of sodium pentachlorophenol was also studied. The effect of a shock loading of sodium pentachlorophenol was found to depend on the concentration of the loading and also on the group of micro-organisms which were predominating. One activated sludge system was seriously impared at a shock loading of …

A Study Of High Strength, Heat Treated Plain Carbon Steels, Ing Shing Chien

Masters Theses

"This work was undertaken as the initial step in a program of studying brittleness in carbon steel that has been heat treated to high strength levels.

The trend in modern technology is toward higher tensile strengths. In practice, only alloy steels are commonly heat treated to very high strength levels. AISI 4340 is one of the more commonly used steels when high strength is desired. It is also becoming almost standard practice to use some of the tool steels or highly alloyed maraging steels for high strength structural components.

For this study high strength in a heat treated steel is …

The Construction Of A Fermi Neutron Chopper For Cross Section Measurements, Cleon Marion Mobley

Masters Theses

"A Fermi neutron chopper and control system has been constructed and put into operation at the end of the UMR Reactor thermal column.

The operation of the chopper has been demonstrated by reproducing the slow neutron cross section data for aluminum and by measuring the previously undetermined slow cross section of cobalt.

The chopper which is powered by a series DC motor consists of 34 cadmium plated stainless steel blades separated by 1/16 inch aluminum spacers. The design incorporates the better characteristics of the Brookhaven and Argonne slow choppers. Speed regulation is accomplished using a silicon controlled rectifier feed back …

A Study Of The Removal Of Alkyl Benzene Sulfonate By Means Of A Column Packed With Sand Coated With Ferric Oxide, Chang I. Fung

Masters Theses

"Iron, precipitated in the form of hydroxides on sand particles (-48 + 65 mesh) and stabilized by drying at 100°C for 10 hours, was utilized to remove alkyl benzene sulfonate (ABS) from aqueous solutions. Solutions containing a maximum of 5 mg/l ABS were passed through a glass column packed with treated sand. The ABS formed a complex with the iron precipitants which adhered to the sand particles.

Preliminary work, in which solutions containing 10 mg/l ABS were treated with various concentrations of FeCl₂ at the equivalence point (pH about 9.5), verified the fact that ABS could be removed by …

A Crystallographic Study Of The Pbzro₃-Pbtio₃-Bifeo₃ Ternary System., Dannie R. Clarida

Masters Theses

"The purpose of this investigation was to conduct a crystallographic study of the PbZrO₃-PbTiO₃-BiFeO₃ ternary system, where all three components are perovskites. Lead zirconate is antiferroelectric, lead titanate is ferroelectric, and bismuth ferrate is thought to be ferroelectric. X-ray diffraction analysis was employed to determine the crystallographic structure and lattice parameters.

A tetragonal region was found to exist in the area of high PbTiO₃ content. A rhombohedral region occurred in the remainder of the system with high BiFeO₃ and PbZrO₃ content, except for an orthorhombic envelope along the PbZrO₃-BiFeO₃ side of the diagram up to approximately 70 per cent BiFeO₃.The …

Tectonic Analysis Of Mare Humorum On The Lunar Surface, Adnan Said Abul-Husn

Masters Theses

"Morphology and internal structures of surface features of the Mare Humorum area were interpreted from photographs and topographic maps. The postulated origin of certain features is based on analog comparisons with known terrestrial features. The laws of crate ring and a newly developed computer program were applied to two representative classes of craters to determine the possibility of a meteoritic impact origin. Some of the craters formed by meteoritic impact and others, including those with a radius larger than 10 Km, probably resulted from volcanic activity.

Mare Humorum formed from centripetal subsidence followed by extensive lava eruptions. Spacially related rilles …

Fast Flux Measurement By A Single Multi-Threshold Foil, Kenneth Lawrence Cage

Masters Theses

"The purpose of this investigation is to determine the fast neutron spectrum by use of a single multi-threshold foil. The foils and the elements which constituted the foils were selected by the following criteria: availability of adequate cross-section data, energy dependence of the given reaction, gamma radiation emitted during decay and the half-life of the daughter. The two foils selected were an In-Fe- P pellet, and ALCOA 2509 (Al-Ni). The gamma spectrum of each constitute was stripped from the composite spectra using a least-squares fit. The activation results were utilized to calculate the fast flux using the weighted orthonormal method. …

The Effect Of Epoxy Resins On The Durability And Unconfined Compressive Strength Of An A-1b Soil, Guy H. Payne

Masters Theses

"This thesis reports the procedure and results obtained from the stabilization of a clean poorly graded sand with various amounts of epoxy resin. The same soil was also stabilized with varying amounts of Portland cement in order to have a basis for comparison of the results obtained. The sand used in this research came from the Meramec River in Central Missouri and is classed as an A-lb soil by the AASHO classification system. The following tests were performed on the stabilized samples: 1. Specimens were molded and compacted at 4%, 6%, 8%, 10% and 12% portland cement by weight of …

Synthesis And Structural Determination Of Intermetallic Compounds In The Fe-Ho System, Gerald J. Roe

Masters Theses

"The intermediate phases in the holmium-iron system were investigated by means of X-ray diffraction and metallographic examination. The intermediate phases identified by X-ray diffraction data were HoFe₂ , HoFe₃ , HoFe₅, and Ho₂Fe₁₇.

A new intermediate phase, HoFe₃, was found. HoFe₃ was indexed as hexagonal with lattice parameters of a = 5.084 Å and c = 24.45 Å, and was thought to be of the space group R3̄̄m.

HoFe₂ was formed by a peritectic reaction and its solidus was estimated to be between 1325°C and 1340°C. suggested to be a congruent melting intermetallic compound with a melting point below 1340°C. …

A Fluid Control System For Nuclear Reactors, Roger Alan Crane

Masters Theses

"This thesis presents both an experimental and analytical analysis of the scram characteristics of a fluid control system for a nuclear reactor. This control system utilizes a control tube containing a neutron-absorbing fluid. The level of the fluid inside of the tube is then regulated by means of' a pressurized gas and offers a number of unique advantages over the conventional control rod system using linear absorber rods.

The effect of varying the level-control pressure and initial height of the fluid column is determined and evaluated. The time required to complete a scram with the fluid control system is compared …

A Numerical Solution For Beam-Columns On Non-Linear Foundations, Wendelin H. Mueller Iii

Masters Theses

"A program for Matlock's recursive method, a numerical method which will analyze beams and columns with linearly varying spring supports, was modified to enable the solution of such members supported by non-linear springs. This modification was accomplished by an iterative technique. The final result of this paper is a computer program which can be used to solve beams or columns with non-linear spring supports, giving as output the deflection, slope, moment, shear, net load and curvature of the structure at uniformly spaced locations"--Abstract, page ii.

A Photoelastic Study Of The Stresses In A Deep Beam Using Partial Mirrors For Isochromatic Fringe Sharpening And Fringe Multiplication, Edward M. Raney

Masters Theses

"This paper is a photoelastic investigation of the stresses in a deep beam using partial mirrors to obtain isocromatic fringe sharpening and fringe multiplication. This method may be of particular value in photoelastic work for obtaining full field fringe multiplication and fringe sharpening for models which exhibit low fringe orders.

The photoelastic model used in this investigation is a deep beam with a length to depth ratio of one. A uniform load is applied over the center one-half of the beam. The beam is supported by two uniform loads distributed over a length of one-quarter the span.

A first approximation …

The Effect Of Structure On The Consolidation Characteristics Of A Clay Soil, Dale E. Sukow

Masters Theses

"This paper reports the results of an investigation conducted to establish the effect of structure on the consolidation characteristics of a clay soil. Soil structure was caused to form in the soil by the addition of electrolytes to flocculate and disperse the clay fraction of the soil.

Consolidation tests were performed on specimens of the treated soil prepared at moisture contents well above the liquid limit of the soil. The consolidation data from these tests are evaluated and comparisons are made to relate the influence of structure to the consolidation characteristics of the treated soil.

The influence of structure on …

An Application Of The Variable Gradient Method Of Generating Liapunov Functions To Discrete Systems, Henry N. Peterson

Masters Theses

"The variable gradient method of generating Liapunov functions has been used only for continuous systems. This thesis presents an application of the variable gradient method to non-linear sampled data control systems.
Certain modifications to the variable gradient method are developed and several examples are presented which demonstrate the application. An attempt was made to synthesize the control system parameters, but due to the complexity of the ΔV functions, the synthesis in general cannot easily be obtained . To circumvent the problem of determining if the ΔV functions are negative definite, a set of computer programs were written to determine a …

Determining The Best Computational Method For Simulation, Neil Hertenstein

Masters Theses

"Two related problems are treated in the discussion. First, what is the best computational means to be used to simulate a given system? Second, if hybrid is chosen, how do we assign the problem to the different computers to realize the fullest advantage of the hybrid simulation? Most of the available information in the literature is presented in light of the above questions. It is found that, despite the lack of a precise theoretical solution, much insight can be gained into the problem. A proposed procedure for hybrid assignment and a sample problem using this procedure completes the discussion"--Abstract, page …

An Algorithm For The Synthesis Of Nand Logic Networks Using A Diagrammatic Approach, Donald Robert Nelson

Masters Theses

"A diagrammatic approach is presented for the synthesis of multilevel NAND networks realizing combinational logic expressions. The network synthesized is restricted to only uncomplemented inputs. The synthesis algorithm involves the determination of minimum sum of products and product of sums expressions for a Boolean function, construction of an α-ß diagram from these expressions followed by implementation with NAND gates directly from the diagram. The resulting network is a minimal or near minimal NAND gate realization of the given function. The algorithm is applicable to completely or incompletely specified Boolean functions and is extended to include NOR synthesis"--Abstract, page 2.

The Plastic Behavior Of Reinforced Concrete Beams With Varying Percentages Of Reinforcing Steel Symmetrically Placed, J. Leroy Hulsey

Masters Theses

"The purpose of this study is to determine the limitations of the plastic behavior of reinforced concrete beams with varying percentages of high strength steel (ASTM-A-432) cutoff in the compression region d distance beyond the point of inflection. Comparison was made with the derived equations.

Steel was placed symmetrically in order to obtain like action at critical sections. The members tested were of a propped beam nature having a total clear span of 5'6" with a 6" overhang on one end and 1'6" overhang on the other. Concentrated loads were applied so as to obtain midspan loading and fixed end …

Further Studies Of The Catalytic Oxidation Of Ortho-Xylene To Phthalic Anhydride Using A Fluidized Bed Reactor., Richard Shih-Chun Chu

Masters Theses

"This investigation was conducted to further study the vapor-phase oxidation or o-xylene to phthalic anhydride in a fluidized bed catalytic reactor. Parameters investigated during the study were temperature, catalyst volume, and catalyst activated by use or different promoters. Two different vanadium pentoxide catalysts were used. One was a new catalyst(Catalyst I) supported on a silica base and diluted with potassium sulfate. The other catalyst(Catalyst II) was similar to the first one except that it had been used in a commercial fixed bed reactor operated by the Monsanto Company, St. Louis, Missouri, using naphthalene as a reed material. It had been …

Anodic Dissolution Of Silver In Aqueous Solutions, B. W. Jong

Masters Theses

"The purpose of this investigation was to study the anodic dissolution of silver in various electrolytes to determine if there existed any deviations from Faraday’s law in nitric acid-silver nitrate solutions. The effect of small additions (10^-4 and 10^-5 N) of Cl^-, SO₄⁼, and CrO₄⁼ on the apparent valence and dissolution potential was also studied. Current densities were varied from 0.00 to 0.07 amp·cm^-2.

Based on the observed apparent valences and a grey film containing metallic particles on the anode surface, it was concluded that deviations from Faraday’s law …

Slope Stability Analysis Of A Fissured Glacial Clay, Byron G. Walker

Masters Theses

"A slope in an over-consolidated, fissured clay was analyzed by the Swedish Method of Slices.

Values of cohesion (c) and angles of friction (Ø) were determined by three different types of direct shear tests (undrained, drained and residual).

Factors of safety (functions of c and Ø) indicated that the direct shear test parameter gave a factor of safety approximately four times that represented by failure conditions in the field. Drained tests gave a factor of safety nearly 2.3 times the value represented by field conditions. The conclusion is made that these two tests are of limited value for slope stability …

Plastic Design Of Steel Frames For Minimum Weight, I-Chen Hung

Masters Theses

"The purpose of this study was to develop a method for weight minimization of the plastically designed frame, braced normal to its plane of action, and composed of prismatic steel members. The method accounts for the non-linear relationship between weight and moment capacity for both beams and columns. Reduction in the pure-bending fully-plastic moment in the presence of axial loading and both beam-column instability and overall frame instability due to sidesway are taken into account. Provision is made for minimization of frames employing standard sections as well as for frames whose built-up members may be chosen from a continuous spectrum. …

Space-Charge Effects As Determined By Initial-Field Conditions, Tsing-Yih Wang

Masters Theses

"A method for calculating the current density passing between two parallel plane electrodes for different values of positive charges as a function of " field at the emitter to field for no charge ratio " is presented.
The problem of the potential distribution between the electrodes has been solved for one particular case in which the positive charges are assumed to be proportional to the field at the emitter. The expressions for the electric field, the velocity of charges, and the charge density as a function of the potential are also presented and plotted as a function of the distance. …

Study Of Heat And Mass Transfer Through Non-Wettable Porous Membrane, Rajender Kumar Rohatgi

Masters Theses

"The object of this investigation was to study the use of non-wettable porous membranes for simultaneous heat transfer and mass transfer of water from a hot salt solution stream to a cold distilled water stream, the streams being in countercurrent flow separated by the membrane. This type of mass transfer was achieved in the experiments, and mass and heat transfer coefficients were measured.

The membranes studied in this work were made of fiberglas treated with Teflon dispersion and aluminum sulphate. The fiberglas membranes yielded desired results. Empirical correlations were proposed which predict values of heat and mass transfer coefficients close …

An Investigation Of The Limitations Of The Antenna Range At The University Of Missouri At Rolla, Ronald Earl Nelson

Masters Theses

"The University of Missouri Antenna Range is described and criteria on range components for acceptable operation are discussed. Discussion of the results of an experimental investigation of component systems of the antenna range is presented. Experimental results are compared to criteria for acceptable operation and recommendations for the improvement of the facility is made. Suggestions are made as to its usage at higher frequencies"--Abstract, page ii.

Upper Cretaceous-Lower Cenozoic Foraminifera From An Oil Well In Northwestern Iraq, Farouk Sunallah Al-Omari

Masters Theses

"Twenty-five samples of well cuttings from the Iraq Petroleum Company Butmah Number 9 Well in northwestern Iraq, at approximately 36° 37' north latitude and 42° 41' east longitude, have been examined in detail. The boundary between the Upper Cretaceous and lower Cenozoic is recorded as closely as possible on the basis of the microfaunal assembalges. A unit showing equivalence to the Danian Stage also is recognized"--Abstract, page ii.

The Thermodynamics Of The Zno-Fe₂O₃-Fe₃O₄ System, Dennis George Dreyer

Masters Theses

"A study was made of the ZnO-Fe₂O₃-Fe₃O₄ system at 1200ºC using oxygen pressures between 0.1 and 1x10⁻⁴ atmospheres. The results of this study were used to calculate the activities of ZnO, Fe₂O₄, and Fe₃O₄ in the spinel solid solution region of this ternary system. The activities of ZnFe₂O₄ and Fe₃O₄ across the pseudo-binary system were then calculated. The activities of the components in both the ternar and pseudo-binary systems exhibited large positive deviations from Raoult's Law, being more pronounced at the higher Fe₃O₄ content. The free energy, enthalpy, and entropy of mixing of the pseudo-binary system ZnFe₂O₄-Fe₃O₄ at 1200ºC were …

The Kinetics Of The Reaction Of M-Nitrobenzyl Bromide With Hydroxide Ion In Aqueous-Aprotic Solvent Mixtures, Ramesh Nagindas Sheth

Masters Theses

"The reaction between m-nitrobenzyl bromide and sodium hydroxide in homogeneous aqueous dioxane and aqueous tetrahydrofuran media was studied.

The product of the reaction was identified by infrared, gas chromatography and chemical tests as m-nitrobenzyl alcohol.
The kinetics of the reaction are second order with practically no variation in the rate constants as the % of the organic solvent was changed in the medium. This seems to imply hydrolysis of the organic halide by a process involving both bond-breaking and bond-formation in the transition state.
The activation energy, measured in 50% aqueous dioxane, between 20⁰ and 69.5⁰C at 5 different temperatures, …