Digital Commons Network^™

Thermal Curing Efficiency Of Geopolymer Mortars, Simon Peter Sargon

Masters Theses

”Missouri is the fourth largest coal consumer in the U.S. with coal-fired power plants generate 81.3% of the electricity in the state which generate about 2.7 million tons of coal combustion residuals (CCRs) annually. The CCR, including fly ash, disposal issue is not limited to Missouri, rather it is a national issue with CCRs being the second largest waste stream in the U.S. Ninety million tons of fly ash are stored in landfills and ash ponds annually. Hence, using this waste product effectively is necessary. One of the emerging applications of fly ash is to use it as binder in …

Enhancement Of Performance Of Micro Direct Ethanol Fuel Cells By Structural Modification, Sindhuja Valluri

Masters Theses

“Direct Ethanol Fuel Cells (DEFC’s) are becoming more important in current energy conversion devices because of their higher efficiency compared to other fuel cells. However, the performance of current DEFC’s is not efficient in providing energy to meet increasing energy demand. The objective of this work is to make the cell compact and at the same time improve performance. For this purpose, we have removed gasket and endplates to make structure compact and increased surface area by developing a new corrugated structure. This work also uses 3D printing technology Fused Deposition Modeling (FDM) to make pocket backing case to improve …

Multi-Objective Optimal Battery Placement In Distribution Networks, Kiana Khalilnejad

Masters Theses

"Due to high penetration of renewable energy resources in today's electricity generation, considerable voltage fluctuations are witnessed in power systems. As an attempt to solve this issue, in this study, multi-objective optimal placement and sizing of distribution-level battery storage system is performed using semidefinite programing. Placement of one or multiple battery system is studied under various objectives including the cost, voltage regulation, reactive power dispatch, renewable resource curtailment, and minimum network power losses. Power flow equations are solved in the form of semidefinite constraints and the rank constraint is ignored. Additionally, combination of these objectives to form a multi-objective problem …

Developing Improved Techniques For Gpr Guided Wave Data Analysis, Yunyi Guan

Masters Theses

"This study was conducted to investigate how limiting the allowable velocity range when analyzing guided wave data will affect the results of dielectric permittivity and thickness estimation. We conducted four sets of Experiments: an underlying layer of saturated organic loam is covered by incremental layers of the dry organic loam; a base layer of dry organic loam covered by the saturated organic loam; a saturated basal layer of silt with overlying dry silt layers, and a base layer of dry silt overlain by saturated silt layers to conduct a comparative study and perform three surveys for each of these three …

Trade Openness, Government Spending, Institutions And Their Effects On Economic Growth In Selected Mena Countries, Saif Mohammad Alqahtani

Masters Theses

The objective of this study to examine how import, export, government spending, and institutions impact on economic growth. Of the four selected North African countries, (Egypt, Morocco, Algeria, and Tunisia), six periods of five years from 1985-2015, we used the panel data model. In this model, we used panel data which consist of random effect and fixed effect, based on Hausman test, we selected one of them. The GDP per capita growth was used as a dependent and import, export, government spending as independent main variables. Also, gross capital formation (GCF), inflation, population growth, and HDI which consist of life …

Numerical And Experimental Analysis Of Local Buckling Of Axially Loaded Steel Tubes Confined By Concrete And Frp, Nicholas Colbert

Masters Theses

“The hollow core Fiber-Reinforced-Polymer (FRP) concrete circular-steel (HC-FCS) column consists of an outer circular fiber reinforced polymer (FRP) tube, an inner thin-walled circular steel tube concentrically aligned, and a concrete shell between them. Research has been performed on the performance of the member as a whole, but to date, there has been no investigation into the behavior of the steel tube confined in the column. 17 small-scale columns were tested under axisymmetric axial compressions applied directly to the steel tube under displacement control. The conducted parametric study examined the effects of diameter-to-thickness (D/t) ratio, concrete unconfined compressive strength, FRP thickness, …

Multiscale Approaches Toward Advanced Lithium-Ion Battery: From Nano To Meso Scale, Susmita Sarkar

Masters Theses

“Battery performance and its degradation are determined by various aspects such as the transport of ions and electrons through heterogeneous internal structures composed of constituent particles, kinetic reactions at the interfaces, and a corresponding interplay between mechanical, chemical, and thermal responses. Further, modern battery materials require a variety of engineering processes such as coating, doping and mixing. As a result, in order to fully understand the behavior of the battery material and improve battery performance, it is necessary to understand and control the individual particle behavior and then connect it to the electrode. This study elucidated the physical phenomena associated …

Solidification Rate Detection Through Solid-Liquid Interface Tracking, Wei Luo

Masters Theses

”Studying the melt pool dynamics in laser powder bed fusion (LPBF) additive manufacturing is vital to predict the microstructure of the built part. High-speed synchrotron hard X-ray imaging is an advanced technique to monitor the LPBF process in situ and in real time. However, it is very challenging to track the solid-liquid interface due to the low image contrast, high image noise and unstable intensity of the image sequences.

In this paper, we propose an solid-liquid interface detector with human interaction to track the interface to compute the solidification rate of the melt pool. The proposed method includes six independent …

Reprocessing Of The 2 Hz P-P Data From The Blackfoot 3c-2d Survey With Special Reference To Multicomponent Seismic Processing, Onur Akturk

Masters Theses

"The 3C-2D multicomponent seismic survey was acquired in the Blackfoot Field, which is located 15 km southeast of Strathmore, Alberta. The 2 Hz vertical component data were reprocessed to better image the target reservoir, the Glauconitic sand formation at approximately 1150 ms. The zone of the major reflector at about 1550 ms was also taken into consideration to determine the better seismic section for further processing. The main characteristics of the converted wave processing, such as common conversion point (CCP), asymptotic binning, gamma ratios, receiver statics, rotation of the data, positive/negative offsets, and anisotropy, were also summarized in this study. …

Data Analysis Of Low-Salinity Waterflooding To Enhance The Oil Recovery In Sandstone Reservoirs, Nadia Ariani

Masters Theses

"The lack of a single reasonable general mechanism to describe how low-salinity waterflooding can improve oil recovery in both laboratory and field pilot projects has increased the interests of many researchers and stakeholders. There has not been observed the relationship of formation brine salinity and injected brine salinity to see how much salinity is reduced to produce the maximum enhanced oil recovery by LSWF. There is no guidance in what EOR stage the LSWF is best implemented. This work collects data from various published literature to develop a comprehensive data set regarding low-salinity waterflooding in sandstone reservoirs. The LSWF mechanisms …

A Novel Power Integrity Modeling Method Based On Plane Pair Peec, Siqi Bai

Masters Theses

"A low impedance power distribution network (PDN) is essential for high frequency integrated circuits. A novel modeling mothed, i.e. the plane pair PEEC method is proposed in this thesis to model the PDN of the multi-layered printed circuit board. The modeling results agrees favorably with full wave simulation and measurement. A PDN tool is develop based on this method"--Abstract, page iii.

Facile Synthesis Of Nanostructured Metal Borides And Composites For Applications In Sustainable Energy, Maalavan Arivu

Masters Theses

"Electrocatalytic water splitting is a promising solution for sustainable energy generation since one of the half reactions lead to the formation of H₂ which is a clean fuel. The other half of the reaction leading to O₂ evolution is an energy intensive process necessitating the need for an electrocatalyst to break the activation barrier for the commencement of the reaction. In this work we will focus on expanding the family of non-oxidic OER electro-catalysts, especially borides, whereby, apart from facilitating delocalization of electron cloud on the catalytically active transition metal site, low anion electronegativity and increased covalency in …

Thermal Analysis And Control Of Small Satellites In Low Earth Orbit, Katelyn Elizabeth Boushon

Masters Theses

"Small satellites are becoming more popular in the space sector, primarily due to their lower cost and shorter development time. Much of the information available about satellite thermal analysis and control refers to larger spacecraft. Sorting through this information to find the practices specifically applicable for small satellites can be a daunting task, particularly for inexperienced engineers. This thesis study is intended to inform the reader about basic thermal control and analysis methods that relate specifically to small satellites in low Earth orbit. A case study involving a satellite designed by the Missouri University of Science and Technology Satellite Research …

An Integrated Method For Understanding The Fluid Flow Behavior And Forecasting Well Deliverability In Gas Condensate Reservoirs With Water Aquifer Drive, Abdulaziz Mustafa Em. Ellafi

Masters Theses

"Gas condensate reservoirs constitute a significant portion of global hydrocarbon reserves. In these reservoirs, as bottomhole pressure falls below the dew point, liquid develops in the pore space. This results in the formation of a liquid bank near the wellbore region that decreases gas mobility, which then reduces gas inflow. Some gas condensate reservoirs have bottom aquifer drive, which also negatively impacts gas production. This research used a field case study to demonstrate an integrated workflow for forecasting well deliverability in a gas condensate field in Libya. The workflow began with the interpretation of open-hole log data to identify the …

Battery Optimization In Microgrids Using Markov Decision Process Integrated With Load And Solar Forecasting, Prateek Jain

Masters Theses

"Rising climatic concerns call for unconventional/renewable energy sources which reduce the carbon footprint. Microgrids that integrate a variety of renewable energy resources play a key role in utilizing these energy resources in a more efficient and environmentally friendly manner. Battery systems effectively help to utilize these energy resources more efficiently. This research work presents a framework based on Markov Decision Process (MDP) integrated with load and solar forecasting to derive an optimal charging/discharging action of Battery with rolling horizon implementation. The load forecasting regression models are discussed and developed. Also, various solar forecasting models like clear sky, multi-regression and Non-Linear …

Examination Of Shear Friction Design Provisions, Nikkolas J. Edgmond

Masters Theses

"This thesis reports the results of research conducted to establish a state-of-the-art database of shear-friction studies to be turned over to ACI Committee 445-0D as a living document, utilize a subset of the established database to examine the effectiveness of the ACI 318 Code (2014), PCI Design Handbook (2010), AASHTO LRFD Bridge Design Specification (2016) and CSA A23.3 Design of Concrete Structures Standard (2014) provisions to predict shear transfer strength, and examine the effective coefficient of friction (µ_e) approach allowed in the PCI Design Handbook (2010).The shear friction design concept is applicable in conditions where direct shear must …

Simultaneous Enhancement Of Fluidity And Thixotropy Of Vibration-Free Concrete, Piyush Rajendra Lunkad

Masters Theses

"This research articulates the development of a vibration-free concrete for slip-form paving enabling a simple and rapid construction process. To achieve this, properties such as rheology including thixotropy, shape stability, and workability loss with time are mainly investigated. Concrete mixture with high thixotropic strength and its shape holding ability, flowability, and workability retention with time is evaluated. This study consists of two phases: (1) selection of paste component from rheology of cement paste incorporating various micro- and nano- sized particles (2) study of fresh properties of concrete mixtures using the excess paste layer concept.

From the cement paste study, it …

Nonlinear Finite Element Analysis Of Concrete Columns Subjected To Complex Loading, Adam Christopher Morgan

Masters Theses

"This study details the development and implementation of a finite element model within a commercial finite element code, Abaqus CAE, for the analysis of reinforced concrete (RC) bridge columns containing interlocking spirals subjected to combined loading conditions including axial, shear, bending, and torsional loads, including the post-peak response. The model is a first of its kind attempt at simulating the response of RC columns with continuous spiral transverse reinforcement and subjected to combined loading conditions including torsion. The model is utilized to determine the quasi-static load-deformation response under various proportions of the input loads and displacements. The resulting quasi-static load-deformations, …

Characterization Of Ionic Liquid Monopropellants For A Multi-Mode Propulsion System, Alex J. Mundahl

Masters Theses

"Multi-mode micropropulsion is a potential game-changing technology enabling rapidly composable small satellites with unprecedented mission flexibility. Maximum mission flexibility requires one shared propellant between the chemical and electric systems. A deep eutectic 1:2 molar ratio mixture of choline-nitrate and glycerol ([Cho][NO₃] - glycerol) is investigated as a fuel component in a binary mixture propellant for such a multi-mode micropropulsion. Specifically, binary mixtures of the novel ionic liquid fuel with hydroxyl-ammonium nitrate (HAN) and ammonium nitrate (AN) are considered and compared against the previously investigated propellant [Emim][EtSO₄]-HAN. Chemical rocket performance simulations predict this new propellant to have …

Management Of Coal Dust Explosions In United States' Coal Mines Using Bag Type Passive Explosion Barriers, Jay Robert Schafler

Masters Theses

"The most significant and powerful hazard that exists in an underground coal mine is a coal dust explosion. A coal dust explosion has the potential to propagate throughout a mine resulting in massive damage to the mine and equipment, as well as tragic loss of life. An assessment of current global regulations and practices uncovered four main control methods utilized to prevent coal dust explosions in coal mines world-wide. The United States is one of the few countries that does not regulate or employ all four of these safety practices. Additionally, a review of past research into coal dust explosions …

Proppant Transport With Varying Injection Points And Its Impact On Proppant Development Inside A Fracture, Shail Janakbhai Soni

Masters Theses

"This study presents experimental work which examines the effect of perforation placement and density on proppant placement within a hydraulic fracture. The study also investigates the effect of proppant angularity.

Experiments were conducted with ceramic proppant injected in a fracture slot model consisting of three injection points at the bottom, middle and top of the fracture slot, and two outlets, at the bottom and top of the fracture model. The effect of single point injection height was investigated by injecting solely at the bottom, middle or top of the apparatus, for both bottom and top outlet conditions. Multiple injection points …

The Role Of Flexural Slip In The Development Of Chevron Folds, Yuxing Wu

Masters Theses

"Chevron folds are characterized by straight limbs and narrow hinge zones. One of the conceptual models to initiate and develop chevron folds involves flexural slip during folding. While some kinematical models show the necessity for slip to initiate during chevron folding, recent numerical modeling studies of visco-elastic effective single layer buckle folding have shown that flexural slip does not result in chevron folds. In this study, several 2D finite element analysis models are run, distinguished by 1) geometry of the initial perturbation (sinusoidal and white noise), 2) varying thewavelength of the initial perturbation (10%, 50%, and 100% of the dominant …

Card: Concealed And Remote Discovery Of Iot Devices In Victims' Home Networks, Sammie Lee Bush

Masters Theses

"Smart devices are becoming more common in the standard households. They range from lights to refrigerators and their functionality and applications continues to grow with consumer demand. This increase in networked, complex devices has also brought an increase in vulnerabilities in the average consumer's home. There now exists an Internet of Things (IoT) ecosystem that creates new attack vectors for adversaries to spread malware, build botnets, and participate in other malicious activities. We will overview some of these new attack vectors as well as go over a framework that would allow an adversary to target a user's home network and …

Reprocessing Of 3c-2d Seismic Reflection Data From The Spring Coulee Field, Alberta, Yasin Demir

Masters Theses

"The 3C-2D seismic datasets were acquired in 2008 in the Spring Coulee Field, Alberta, which is located in Township 4, Range 23, and west of the 4th Meridian in the Alberta Basin. Line 2008-SC-01 was reprocessed to obtain better image of the formation targeted at between 1300 ms and 1400 ms. The depositional settings of the Madison Formation consist of shallow and carbonate shelf deposits. The processing workflow was designed by testing several methods, algorithms, and parameters, and finding the optimal processing solution. The processing steps included elevation statics, noise suppression, deconvolution operator, and 2D Kirchhoff poststack time migration. In …

Microstructural Development And Its Effect On Aqueous Corrosion Of A Borosilicate Glass Ceramic For Waste Vitrification, Nicholas Stephen Roberts

Masters Theses

"Waste loadings of reprocessed spent nuclear fuel vitrified into borosilicate glass can be increased by precipitating environmentally stable phases concentrated with waste components in a chemically stable glass matrix. The principal objective of this thesis was to characterize the development of crystalline powellite (CaMoO₄ and related phases) and oxyapatite (Ca₂LN₈Si₆O₂₆) in borosilicate glass-ceramics and to determine how the formation of those phases affected its chemical durability.

Borosilicate glasses provided by PNNL were re-melted and quenched at rates from over 300⁰C/s to ~0.05⁰C/s. Isothermal heat treatment experiments were conducted by quenching melts …

Tvs Transient Behavior Modeling Method, And System-Level Effective Esd Design For Usb3.X Interface, Pengyu Wei

Masters Theses

"This research proposal presents a methodology whereby a protection device can be modeled in SPICE compatible platforms with respect to the transient behaviors during Electrostatic Discharge (ESD) events. This methodology uses an exclusively "black-box" approach to characterize the parameters of the protection device, thereby allowing it to be implemented without intimate knowledge of the DUT. Results of this methodology can be used to predict the transient response (conductivity modulation and snapback delay) of the ESD protection devices, and thereby predicts how much current could flow into the device (typically a digital IO pin) under protection. The transient behavior modeling methodology …

Spatial Resolution Study For Magnetic Near-Field Probe, Xin Yan

Masters Theses

"Spatial resolution is an important factor of near-field probe, which represents the ability to distinguish two close radiation sources. Traditional definition of spatial resolution is the distance between peak point and -6dB point when measuring microstrip line. The definition has disadvantage and limitation. In this topic, spatial resolution for magnetic near-field probe is studied, and three dimensions of spatial resolution are put forward. An optimized measurement setup is presented to reflect spatial resolution of probe properly. Then, an example is given to show how spatial resolution affects field distribution in near-field measurement"--Abstract, page iv.

Comparative Toxicology Of Nio And Ni(Oh)₂ Nanoparticles, Melissa Hope Cambre

Masters Theses

“Understanding the potential toxicity of nanoparticles (NPs) is important to ensure that these new products do not impose harmful effects to human and environmental health. Paper I is a literature review in which we discuss characteristics of nanomaterials, with an emphasis on transition metal oxide nanoparticles that influence cytotoxicity. Identification of those properties may lead to the design of more efficient and safer nanosized products for various industrial purposes and provide guidance for assessment of human and environmental health risk. We then investigate biochemical and molecular mechanisms of cytotoxicity that include oxidative stress-induced cellular events and alteration of the pathways …

Bifunctional Porous Polymeric Fiber As A Catalyst For N-Phenylglycine Synthesis And Carbonation Of Propylene Oxide To Propylene Carbonate, Ahmed Abdulghani Almuslem

Masters Theses

"In this study, development of a polymeric bi-functional porous catalyst that can be used in various applications such as batch, packed-bed, and continuous flow reactors and the formation of highly important chemicals that have many applications in the industry. With this material many homogenous reactions can be conducted in heterogeneous environment which is more efficient and profitable. The catalyst was formed by grafting hollow fiber with APS then immobilized with Br using 1,2-dibromoprobane (Br/APS/PAI-HFs). The formed catalyst was tested with BET and FTIR to confirm the immobilization of Br. A porous polymeric material Br/APS/PAI-HFs provides the ability for ring opining …

Cyclic Axial Compression Behavior Of Concrete-Filled Hybrid Large Rupture Strain Frp Tubes, Monika Nain

Masters Theses

"This study introduces an experimental investigation of the behavior of concrete filled fiber reinforced polymer (FRP) tubes (CFFTs) under cyclic axial compression. The FRP used in this study were either small rupture strain FRP (SRS-FRP) or large rupture strain FRP (LRS-FRP). This paper also presents the first-ever experimental study on the behavior of concrete confined using hybrid LRS-FRP and SRS-FRP. LRS-FRP included PEN (polyethylene napthalate) and PET (polyethylene terephthalate) where both of them having ultimate axial strain larger than 5%, and low stiffness. SRP-FRP included carbon and glass FRP having small rupture strains, smaller than 2%, and high stiffness. The …