Digital Commons Network^™

A Resistivity Study Of Hot Short Ferrous Alloys, Harold Alfred Koelling

Masters Theses

"Resistivity measurements were performed at elevated temperatures on four special ferrous alloys and one commercial iron. The alloys were pure iron, iron with .023 per cent sulfur, iron with .33 copper, iron with .32 copper and .024 sulfur. Other elements were held to the minimum amounts possible in order to determine the actual effects of sulfur and copper. The commercial alloy was Armco Iron.

Measurements of resistivity versus temperature were taken at slow heating rates to determine if the iron sulphide liquid film formed in the grain boundaries of red-short steels had any effect on the electrical resistivity"--Abstract, page 7.

A Study Of The Hood Inlet And Its Possible Use As An Overflow Structure For A Sanitary Lagoon, Richard Irwin Boe

Masters Theses

"A closed conduit, such as an overflow pipe for a conservation pond or a sanitary lagoon, will not flow full if laid on a slope that is hydraulically steep unless the pipe entrance receives special attention. A steep conduit slope is necessary to insure that the pipe entrance controls flow.

The recently introduced hood inlet will permit the closed conduit to flow full, even if on a hydraulically steep slope, upon a slight submergence of the inlet crown. The hood inlet is formed by cutting the pipe at an angle so that the crown of the inlet projects beyond the …

Tank Studies Of The Resistivity Horizontal Profiling Method Of Electrical Prospecting, Edward Hornsey

Masters Theses

"This research project was undertaken to perfect a technique whereby theoretical horizontal resistivity profiles could be reproduced in laboratory tank studies.

Several specimen materials were tried and finally an acceptable specimen material was found. It was found that carbon specimens suspended in salt water would give horizontal resistivity profiles that agree to a remarkable degree with the theoretically predicted curves.

The investigations showed that the depth of burial of the specimen has a marked influence on the position of the characteristic edge effects and on the magnitude of the apparent resistivity.

The studies also indicated that successful tank studies could …

Effects Of Solids On Friction Factor In A Sand-Water Mixture, Frank J. Capek

Masters Theses

"At the present time various industries in both the United States and Europe are very interested in using pipelines as a means of transporting solids. The pumping of solids in pipelines isn't new, however, many of the pipelines in use today were constructed on an empirical basis. This is primarily due to the lack of knowledge concerning the flow properties in fluid-solid mixtures and slurries. With this need for fundamental information in mind, the author made a study on the effect solids have on the friction factor in fluid-solid mixtures.

In this paper various percentages of fine and coarse sand …

Sedimentary Features And Geochemistry Of The Sulphide Facies In The Transition Between The Lamotte Sandstone And The Bonneterre Formation In The Fredericktown Area, Madison County, Missouri, Farouk El Baz

Masters Theses

"SCOPE AND PURPOSE The Lead Belt area of southeast Missouri, which is nearly 40 km. long and 10 km. wide, is considered, at the present time, the most important lead district in the world. Lead has been mined in this area by the natives prior to 1720, and almost continuously up to the present day. A variety of sulphides are mined from different places in the district.

The sulphide deposits in the Lead Belt are considered to be typical examples of the Mississippi Valley Type Deposits, which are distributed all over the world. As in practically all the Mississippi Valley …

Design, Construction And Operation Of Equipment For The Study Of Evaporation Of Aqueous Solutions Using A Simplified Reactor Design Approach, Virendra Kumar Mathur

Masters Theses

"The study of simultaneous heat and mass transfer in flow reactors has attracted the attention of many workers for a long time due to its wide application in the industrial field. These heat and mass transfer studies play an important role in determining the rate equations and in turn the size of the reactor itself. A large number of chemical reactions have been studied by various workers….

The purpose of this work comprised only the initial or exploratory phase of this overall project, and deals with the design, construction and assembling of the equipment necessary to carry out the vaporization …

Gladstone, The Irish Home Rule Question, And Its Effect On The Liberal Party, Kenneth John Van Dellen

Masters Theses

Introduction

Purpose

The Victorian Age of English history produced many great political leaders. Among the best known are Chamberlain, Disreali, Palmerston, Salisbury, and Gladstone. These politicians were able to pacify many dissatisfied groups and produce many reforms. Yet one of the biggest problems they had to face was left unsolved throughout the Victorian period, and the later Edwardian period as well. This problem was Ireland.

This research project will deal with the man who made one of the most persistent efforts of the nineteenth century to solve the Irish problem. It will attempt to show how William Ewart Gladstone become …

A Follow-Up Study Of Western Michigan University Graduates With Majors In Industrial Arts, Richard Duane Murphy

Masters Theses

Chapter I

Introduction

One of the major premises of education is that programs must be constantly exposed to evaluation. One of the means implementing such evaluation is the use of a follow-up study. By using the results of such a study, the institution can keep its program in step with the best educational theory and practice.

Cyclic Sedimentation Of The Upper Fayetteville Formation, Faramarz Frouzan

Masters Theses

"In the past decade considerable interest has developed in the geology of the Boston Mountain area of northern Arkansas. This has been due to exploration for oil and gas in-the area and the related desire to know more about the structure and stratigraphy of the region. Principal work has been done by the University of Arkansas, the United States Geological Survey, and oil companies. This study involves only one of the formations making up the geologic column in the Boston Mountains, the Upper Mississippian (Chesterian Series) Fayetteville Formation.

Portions of the upper part of the Fayetteville Formation of northwestern Arkansas …

The Organization And Administration Of The Marching Band, George L. Bailey

Masters Theses

No abstract provided.

A Study Of Motivation In Selected Plays Of Shakespeare's Plays, Robert Edward Zimmerman

Masters Theses

No abstract provided.

A Method Of Design For Spiral Reinforced, Eccentrically Loaded, Concrete Columns, Lloyd O. Senter

Masters Theses

"This thesis presents a method of designing spiral reinforced, eccentrically loaded, concrete columns on the basis of the 1957 American Association of State Highway Officials specifications.

Equations from AASHO, in conjunction with equations derived in this thesis, are programmed for and solved by the IBM 650 digital computer. The data obtained from the computer is plotted such that, given the normal load and moment on a column, the minimum required area or reinforcing steel may be read directly from the graph.

The derivation or equations, the computer program, and the graphs are included in the thesis"--Introduction, page 1.

Temperature Distribution In A Semi-Infinite Solid As A Function Of The Input Heat Flux, Lloyd Carl Laciny

Masters Theses

"In this thesis the problem of varying heat flux into a semi-infinite solid initially at zero temperature is investigated. Varying heat flux means that the heat transferred to the solid by its surroundings is a function of time; in this particular problem it is chosen to be an exponential function of time. A semi-infinite solid is one which is bounded by only one plane.

This subject has achieved considerable importance in the field of space technology. A body in space is beyond the realm of aerodynamic heating and non-uniform skin temperatures reached as a result of radiation from a high …

The Constitution Of Magnesium-Rich Magnesium-Zirconium Alloys, Kenneth Allen Fowler

Masters Theses

"The magnesium-zirconium system has been studied to 0.8 per cent zirconium which represents the limit of solubility of zirconium in liquid magnesium at 950°C. Alloys have been prepared by two methods of alloy additions, and the results compared. Microstructural studies have been made of the alloys in the cast, extruded, and heat-treated conditions. The limit of solid solubility has been determined on the basis of resistivity and temperature coefficient of resistivity measurements, as well as by metallographic examination, with good agreement. A secondary structure resulting from precipitation of a second phase within cored regions of the alloy has been studied …

Physical Property Tests Of Rock, Centrifugal Tests And The Design Of Underground Mine Openings, Samuel Shu Mou Chan

Masters Theses

"Proper design of stable underground mine openings is important to the mining industry today. Various methods have been utilized by investigators to approach this goal.

A review of previous investigations of each of the phases of underground mine opening stress analysis is presented.

An approximate method of designing underground mine structures based on estimation of the initial stress field, rock physical property tests, and model tests, together with preliminary field data, is presented, and a specific example given"--Forward, page i.

Design Of An Intermediate Frequency Amplifier And Variable Frequency Oscillator, Robert Charles Mcintyre

Masters Theses

"Since the advent of the transistor in 1948 many technological barriers have been overcome in the field of semiconductors. Unfortunately, however, there is a considerable period of time between the discovery of a scientific phenomena and its widespread use and understanding by practicing engineers. The motivating factor which prompted this investigation was primarily the lack of knowledge which the author possessed concerning transistors. The selection of the amplifier and oscillator design confined the study primarily to the transistor. Considerable time, however, had to be spent in the study of basic transistor theory before any phase of the design could be …

Effect Of Boundry Layer Control, Through Surface Holes, On The Film Coefficient Of Convective Heat Transfer, Jainti Prasad

Masters Theses

"This thesis has as its objective, the effect of some boundary layer control on the convective heat transfer film coefficient, metal to liquid. The boundary layer control was produced by drilling 1/16 inch diameter holes on the tube surface.

In this modern world of atoms and the current development of large quantities of its energy at low cost, the subject of designing heat exchange devices of higher efficiency is receiving considerable attention. In a reactor, or any type of heat exchange device, there are limits for the temperatures of a heat exchange surface because of corrosion, strength of metals etc. …

A Thermodynamic Study Of The System Pbo-Pbs, John P. Hager

Masters Theses

"An experimental investigation was conducted in order to determine the thermodynamic and kinetic behavior of the system PbO-PbS.

The thermodynamic behavior of the system PbO-PbS was studied by measuring the P_SO₂ in argon-SO₂ mixtures equilibrated with various PbO-PbS mixtures in a recirculating-type equilibrium apparatus, and analyzing the condensed phases by means of X-ray diffraction.

The effect of temperature and PbO/PbS ratio on the rate of SO₂ evolution was investigated in order to determine the reaction mechanisms involved in the approach to equilibrium.

A sodium hydroxide, hydrogen peroxide titration technique was employed in the analysis of SO_{2 …}

Construction Of Distillation Solvent Recovery System, Joseph Richard Aid Iii

Masters Theses

"When a nuclear fuel is “burnt” in an atomic reactor it is not possible to completely utilize the fissionable material present due to build-up of fission products (which act as poisons), depletion of the fissionable material, and radiation damage to the fuel elements. Chemical processing of nuclear fuels is concerned with the recovery of the fissionable materials, specifically uranium, plutonium, and thorium, from the spent fuel elements. There are two general methods of reprocessing nuclear fuels: aqueous and non-aqueous. The aqueous methods include solvent extraction, ion exchange, and precipitation. Comprising the non-aqueous methods are fluoride volatility and pyrometallurgy. At the …

Automatic Tuning Of A.C. Compensating Networks, Giles C. Sinkewiz

Masters Theses

"The purpose of this thesis is to illustrate the practicality of using an auxiliary servo system to shift parameters in damping networks of the main servo system.

Since amplification is most easily achieved with A.C. amplifiers and since A.C. servo motors are superior in operation to D.C. servo motors, because no brushes or commutators are needed, the A.C. servo system is widely used. However, one major problem is confronted when designing an A.C. servo system. This is the problem of designing damping circuits and compensating circuits which are insensitive to carrier frequency fluctuations. Notch filters provide the desired transfer functions, …

The Evaluation Of The Influence Of Large Aggregate On The Permeability Of Single-Grained Soils, Edward Clayton Grubbs

Masters Theses

"Each year many earth fill structures are designed and built with the primary purpose of impounding water. As these structures are only relatively impervious, engineers must consider the control of seepage in design. In order to predict seepage, the engineer must have knowledge of the potential flow or water through the earthen structure. He is, therefore, faced with the problem of determining a coefficient of permeability for use in design calculations.

The coefficient of permeability is easily enough determined for fine-grained materials. However, in construction it is very rare to find proper fill material which does not include quite a …

Preparation Of Casting Slips Containing Ferrous Powders And Alginates, Robert Eugene Newcomer

Masters Theses

"The preparation of casting slips containing ferrous powders dispersed by alginates was studied and an attempt was made to determine the mechanism by which suspension was attained. The colloidal aspects of preparing ceramic casting slips are discussed and an analogy is drawn to preparation of metallic slips suspended by alginates.

Sodium and ammonium alginates were used to suspend stainless steel and iron powders. The effect of NaOH, HC1, and various phosphate additions on the properties of slips and algin solutions was considered.

It was found that colloidal concepts can not be applied to explain observed behavior in the system studied. …

Occurrence Of Mineralized Ground Water In Southern St. Louis And Jefferson Counties, Missouri, Willard Glennon Owens

Masters Theses

"Mineralized ground water occurs at some localities in southeastern St. Louis and northern Jefferson counties, Missouri. This water is usually undesirable and is detrimental to development of ground water resources.

Water well records in the offices of the Missouri Geological Survey and Water Resources provided data for a study of structure, lithology and occurrence of ground water. Water well drillers and property owners were interviewed to obtain additional information concerning drilling problems and quality of water.

Geologic cross-sections, subsurface contour maps and isochlorinity maps aided the study of lithology, structure and areal distribution of mineralized ground water. Relationship is suggested …

A Study Of The Feasibility Of Stabilizing Putman Soil With Hydrated Lime And Portland Cement In Combination, John Henry Kern

Masters Theses

"This paper is the report of a feasibility study of the combined use of hydrated lime and portland cement to stabilize the troublesome Putnam soil of northern Missouri. In its natural state, this soil is highly plastic, possesses great shrinkage and swell characteristics when the moisture content is changed and is classified as an A-7-5 soil by the A. A. S. H. O. Standards for the Classification of Highway Subgrade Materials.

During the course of this investigation, the following tests were performed: (1) Moisture-Density Relationships for soil with admixtures; (2) Triaxial Compression Test; (3) Unconfined Compression Tests; (4) Freeze-Thaw Tests; …

The Equalization And Optimization Of A Third-Order Type-1 Position Control System, Viswanatha Seshadri

Masters Theses

"While the practice of feedback control dates back to the day when the earliest living organisms began to react to their environmental conditions and the changes therein, it has been only during the past two decades that this technique came to be subjected to a scientific examination. Yet, an astoundingly rapid advancement has resulted in the field of servo-mechanisms, contributing substantially to the development of modern civilized existence and activity to its present standards, and promising to contribute, to an ever-increasing extent, to the accelerated progress of scientific and industrial enterprise in this space age.

The principal concerns of the …

A Study Of The Reaction Of Hydrated Lime With Pure Clay (Kaolin) In Clay Stabilization, Chiyyarath Velayudhan Girijavallabhan

Masters Theses

"The work presented is the investigation of the reaction of pure Kaolinite clay with hydrated lime in clay stabilization. Pure Kaolin clay, ranging from one micron to five microns in size, was mixed with calcium hydroxide in the form of a paste. These mixtures were permitted to react for varying periods of time. An attempt was made to separate the lime from clay lime mixture by density separation using a mixed solution of carbon tetrachloride and tetrabromoethane. Since the above method failed because of the formation of a yellow gelatinous suspension, the lime was removed by washing the clay lime …

The Lattice Constants Of Chromium And Vanadium Containing Dissolved Gases, Paluri Bhimeswara Rao

Masters Theses

"The physical properties of chromium and vanadium are so important that a study of their lattice constants and their coefficients of thermal expansion, requires special consideration.

A number of research workers, over a period of about forty years, have done considerable work in determining the above constants. Some of the previous investigators found an anomaly in the thermal expansion, electrical resistivity and other physical properties of chromium. They observed that at about 37°C, chromium showed a discontinuity in the above physical properties. However it is not known what causes the discontinuity in the expansivity curve of chromium. The discontinuity may …

A Method For The Prediction Of Detection Ranges For Pulsed Doppler Radar, Phillip Orlan Brown

Masters Theses

"Modern radar systems must provide greater detection ranges both against high and low altitude targets because of the significant advances in weapon speed and range. Extended range indicates that the power transmitted by the radar must be increased. It follows, that ground return becomes a problem even at high altitudes.

There are at present three basic types of radars which are (1) pulsed, (2) continuous wave, and (3) pulsed doppler radar. The conventional pulsed radar now closely approaches the theoretical optimum performance; however, it does not have the inherent ability to distinguish between ground return and moving targets. The continuous …

A Dissolution Rate Study In Hydrofluoric Acid Of Titanium And The Alpha Solid Solutions Of Oxygen In Titanium, John L. Ratliff

Masters Theses

"The dissolution mechanism of titanium in hydrofluoric acid was studied by collecting the hydrogen evolved during the dissolution reaction. A concentration range of 0.05 N to 0.50 N and a temperature range of 15°C to 45°C were employed for the determination. Values of the reaction order and energy of activation were determined for both pure titanium and the alpha solid solutions of oxygen in titanium and found to be the same within experimental limits. This indicated that the reaction giving rise to hydrogen evolution on the surfaces of both pure titanium and the TiO_x alloys was the same. The …

The Effect Of The Rare Earth Elements On The Hot Workability Of Ingot Iron, L. A. Neumeier

Masters Theses

"The effect of mischmetal and rare earth oxides on the hot workability of ingot iron in the hot-short region was studied. Thirteen heats were melted in air in a basic-lined induction furnace. All heats were thoroughly deoxidized with aluminum prior to the rare earth additions. Mischmetal was added in amounts of 0.1, 0.3 and 0.5 per cent. Rare earth oxides were added in amounts of 0.1 and 0.2 per cent. Temperatures were maintained at approximately 2900°F and holding intervals between mischmetal additions and pouring at two minutes. Bars were hot rolled and swaged for hot twisting in the hot-short region. …