Digital Commons Network^™

Experimental Evaluation Of Thermal Stresses On The Outer Surface Of A Thick-Walled Tube., Vinodray T. Patel

Masters Theses

"In this investigation an attempt has been made to measure thermal stresses on the outer surface of a thick- walled tube. The inside surface was heated by steam passing through the tube while the outer surface was cooled by water. Two temperature compensated strain gages were used to measure strains in the tangential and axial directions respectively. The advantage of using this type of strain gage is to avoid the use of a dummy gage to compensate for the temperature effect.

The analytical solution to the problem was derived and the values of thermal stresses were calculated theoretically and compared …

Longitudinal Spin Relaxation Of Optically Excited Rubidium., John Robert Martin

Masters Theses

"This thesis is intended to be a guide to the theory and experimental procedures of optical pumping in one of its most usual applications. It is also intended to be an extension of the work done here by Steinbruegge¹ in 1963 along with several significant changes and improvements in experimental techniques. A study is made of the optical pumping of rubidium vapor, and results are given stating the most efficient methods with which to produce large populations of optically oriented rubidium atoms, and thereby determine the relaxation properties of a given rubidium system"-- Abstract, p. ii

Study Of Mass Transfer In Oscillating Droplets., Subhash Vishnu Gangal

Masters Theses

"The object of this investigation was to study the resistance to mass transfer inside single oscillating liquid droplets falling in a liquid medium. The following four systems were studied: (1) 3% acetic acid in nitrobenzene and water, (2) 25% acetic acid in nitrobenzene and water, (3) 3% acetic acid in nitrobenzene and glycerin in water, and (4) benzyl alcohol and water. The individual mass transfer coefficients were computed by using the Handlos and Baron relation and were compared with the experimentally determined dispersed phase mass transfer coefficients. The average absolute deviation of the observed values of dispersed phase mass transferred …

Separation Of Cationic And Colloidal Fractions Of Radioactive Fission Elements By Electrodialysis., Ronald Dean Mitchell

Masters Theses

"The rapid increase in radioisotope applicat i ons necessitates improved technology for separation and purification of the fission product elements. Electrodialysis techniques employing Permutit anion exchange membranes (3148) and cation exchange membranes (3142) were used to separate strontium from cesium and to fractionate cerium from promethium. The methods were based upon organic complex formations in basic solution.

Separations of radio strontium and radio cesium were affected with both anion and cation exchange membranes in a three-cell electro dialyzer with EDTA as a chelating agent at a pH of 11.0o Fractionation of radiocerium and radio promethium were affected with anion exchange …

Determination Of The Shapes Of Fixed And Moving Polodes Of Class Ii Four Bar Mechanisms., Manharkumar Kantilal Sheth

Masters Theses

"The purpose of this thesis is to determine the shapes of fixed and moving polodes of class II four bar mechanisms, since there has been little, or no work done in determining their shapes.

Twenty different mechanisms were taken to study the shape of the fixed and moving polodes. The best equation which fits each curve was found by using the least square method in polynomials. Coefficients for each curve were determined with the help of the I.BM 1620 computer. The equation was found to be a six-degree polynomial which fits very well to each curve. There seems to be …

The Effects Of Surface Flaw Density And Configuration On Fracture Stresses Of A Triaxial Porcelain., William H. Daniels

Masters Theses

"The fracture behavior of a model brittle solid containing artificial surface flaws was studied. An industrial ceramic porcelain body was employed as the model brittle material. Sample groups of specimens containing 6, 11, 24, 49,. and 90 sharp surface notches uniformly distributed over a four inch length were broken under pure bending. The fracture data we-re compared to those of an identically treated control group containing no artificial flaws.

The mean strengths of the two groups of lowest flaw density were identical, both being significantly less than that for the control group. Further increases in flaw density resulted in increased …

A Study Of A Method For Selecting The Best Of Two Or More Mathematical Models, August J. Garver

Masters Theses

"A method for selecting the best in some sense of two or more mathematical models is investigated in this study. The method is that of using part of the data to estimate parameters and using the resulting equation to predict the additional data which are then compared with the existing data not used in estimating the parameters. In particular the effects produced on the method by the number and location of points used in estimating the parameters and the criterion for determining the best fit are investigated. It was concluded from the results of an empirical investigation that the success …

Transverse Spin Relaxation Of Optically Pumped Rubidium., Robert Evans Hufft

Masters Theses

The study of the transverse spin relaxation of rubidium vapor is a continuation of the work done by Kenneth Steinbruegge¹ and that in progress by John Martin² at the University of Missouri at Rolla. The purpose of the experiment is to study the change of intensity of the transmitted pumping light at resonance in the longitudinal direction, and the observation of the high frequency modulation of a second "cross" beam of light perpendicular to the first. Under resonant conditions this "cross" beam will exhibit a phase coherence and a loss of phase coherence when parameters of the experiment …

Influence Of Quartz Particle Size And Concentration On The Fracture Stresses Of Triaxial Alumina Porcelain., John David Weyand

Masters Theses

"Quartz particles were introduced into a typical triaxial alumina porcelain. Three levels of particle size and three levels of concentration were studied. The strength sample sizes were large. A diametral- compression loading method was used for strength testing. It was found that the porcelain strength decreased with increasing grain size and concentration of quartz particles. A linear relationship existed between log quartz concentration and mean fracture stress"--Abstract, p. ii

Application Of An Orifice Meter To Fan Testing., J. F. T. Agapito

Masters Theses

"In this investigation the application of an orifice meter to fan testing was studied and evaluated. An orifice meter was designed and was installed in a centrifugal fan duct. Measurements were checked and compared with those of a standard pitot-tube traverse and were found to be in very close agreement. It is suggested that a meter of this type could easily be adapted not only to laboratory work but also to field tests"--Abstract, p. ii

Solid Solubility Of Sodium Oxide In Tricalcium Aluminate, Joel A. Conwicke

Masters Theses

"The tie line connecting the compounds 3CaO·Al₂O₃ and Na₂O·8CaO·3Al₂O₃ in the ternary system CaO-Al₂O₃-Na₂O was studied at 1250° Celsius.

It was determined that Na₂O can exist in crystalline solution with 3CaO·Al₂O₃ in percentages of about 2.3% or less without any apparent change in the structure of 3CaO·Al₂O₃. X-ray diffraction peaks in the back-reflection region shifted to lower d-spacing values on increasing Na₂O contents.

At a Na₂O content of about 2.7%, each major x-ray …

The Effect Of Surface Roughness, Cure Pressure, And Temperature Level On The Thermal Resistance Of Bonds And Contacts, David Leo Schwaller

Masters Theses

"This investigation was conducted to determine the thermal effect of temperature level, surface roughness, and curing pressure on bars and bonded interfaces.

The equipment used in this investigation is shown in Fig. 1 and Fig. 2. The four specimens used, cylindrical aluminum alloy bars, were cut radially at their midpoints and faced on a lathe. Heat was supplied by an electrical resistance heating element and an ice bath was used to conduct heat from the alloy specimen. A heat shield was used to insure one dimensional heat flow. Spacers were placed in the insulation at the top, the interface, and …

The Effect Of The Static Compaction On The Mechanical And Physical Properties Of Asphalt Concrete Hot-Mixes, Abdel-Gawad A. Bahgat

Masters Theses

"The objective of this investigation was to study the effect of the static compaction effort upon the physical and mechanical properties of asphalt concrete hot mixes. To study the effect of the static compaction upon the physical properties of the asphalt mixes, six mixes were prepared using hard, well graded crushed limestone as an aggregate, blended with an 85-100 penetration grade asphalt cement. The control mix was prepared and tested in accordance with the Marshall method for mix design. The other five mixes were prepared and tested using the same procedures of Marshall except for compaction, where five different static …

The Dielectric Properties Of Thallium Nitrate., Gene E. Gowins

Masters Theses

"The purpose of this research was to investigate the dielectric behavior of thallous nitrate and to determine whether it belongs to space group Pbnm or to Pbn2.

The growing of single crystals of thallous nitrate which are suitable for dielectric measurements is difficult because the crystals are prone to initiate a dendritic growth habit. In the present work single crystals of thallous nitrate were obtained, however, by slow evaporation of an aqueous solution at 55 degrees centigrade. The crystals were plates, not larger than 8 x 8 x 2 mm, whose principal faces were subsequently indentifled as (001) planes. The …

A Study Of Stability Of Numerical Solution For Parabolic Partial Differential Equations., Tsang-Chi Huang

Masters Theses

"Parabolic partial differential equations hold a very important position in science and technology since they are encountered frequently in the solution of diffusion and heat-conduction problems. Theoretically, it is possible to solve many of these equations by analytical methods, but the modern development of mathematics has revealed that there are numerous difficulties in obtaining the solution. Numerical solutions for most applied problems of a parabolic partial differential equation type are practically necessary, thus methods for numerical solution or approximate solution became more important. Since numerical results are required for most applied problems of a parabolic partial differential equation type a …

Determination Of Transient Temperature Stresses In Plates, Teh Yu Hu

Masters Theses

“The purpose of this thesis is to determine the transient temperature stresses in two-dimensional plate structures restrained against rotation at the ends but not restrained against elongation. In this investigation, only one-dimensional heat flow is considered. The heat flow is first treated as a problem in pure conduction and then the effects of convection through a boundary layer are considered.

The differential equation of transient heat conduction is solved by Fourier series and Duhamel’s theorem, and a graphical method of solution for temperatures in terms of dimensionless parameters is presented.

Solution of this problem is valid for a semi-infinite plate …

Nature And Lateral Variation Of Lost Rock Limestone In The Tri-State Zinc-Lead District., Adnan A. Saadallah

Masters Theses

"The nature and lateral variation of a host rock limestone in the Tri-State zinc-lead district were petrographically studied within a single horizon, the M bed. This bed is a massive crinoidal limestone in the Tri- State district of southwestern Missouri, northeastern Oklahoma and southeastern Kansas and is a part of the Mississippian Keokuk Formation.

One hundred and twenty specimens from this bed were collected underground from six pull drifts in five mines: West Side, Grace B, Big John, Little Greenback, and Mudd Mines. The specimens were collected at regular intervals, usually ten to twenty feet, beginning at the edge of …

A Study Of Methods For Estimating Parameters In The Model Y(T) = A₁E-P₁T + A₂E-P₂T + Ε, Gerald Nicholas Haas

Masters Theses

“In this study, methods for estimating the unknown parameters A₁, A₂, p₁, and p₂ in the model
y(t) = A₁e^-p₁t + A₂e^-p₁t + ϵ
where ϵ ~ N(0, σ) are investigated. In the model investigated, A₁, A₂, p₁, and p₂ are positive.

Four methods, one non-iterative method and three iterative methods, for estimating parameters in this model are investigated. The non-iterative method is known as Prony's Method. The three iterative methods are (1) the Modified Gauss …

A Theoretical And Experimental Study Of The Stress Distribution In An Infinite Plane Shrink-Fitted On Four Circular Elastic Pins, Charles H. White

Masters Theses

"The purpose of this study is to show a general method of solution for multiple inclusions in an infinite plane. The shrink-fitting of an infinite plane upon the inclusions, or pins, will be simulated by force-fitting the pins into a large sheet of birefringent material, to obtain an experimental verification of the analytical solution.

The problem to be approached is that of four circular elastic pins shrink-fitted in an infinite plane. The method of superposition will be used, and the stresses at any point in the plane found with respect to a common origin of coordinates. It will first be …

Investigation Of Inoculant Effect On Cast Iron, Darrell W. Donis

Masters Theses

"An assumption was made that extensive holding time of an inoculated gray iron melt would result in a loss of physical properties of castings poured from this melt. This theory was examined in both a literature search and by testing and conclusions drawn from these findings are presented and discussed. Although there is a great deal of data available which discusses inoculants and their effects, very little mention is made of the effect of holding time in any of this material. The results indicate that holding time is of considerable importance when dealing with inoculated iron, and that calcium silicon …

An Investigation Of The Adaptability Of The Linvill Model For Transistor Synthesis, John A. Reagan

Masters Theses

"The Linvill transistor model may be used for transistor synthesis if the model accurately approximates transistor response and may be readily simulated on an analog computer. Experiments were performed on a transistor to determine the Linvill model parameters. The transistor's large-signal transient response was investigated by pulsing the emitter with a current that drove the transistor from the active region of operation into saturation. The same problem solved experimentally was then solved analytically by replacing the transistor with the Linvill model. The experiment was then simulated on an analog computer by using the equations that govern the Linvill model's response. …

A Laboratory Study Of The Effect Of Wettability Of Residual Oil Saturation In Artificial Cores., Socrates Nicholas Potamianos

Masters Theses

"In the past much emphasis has been placed on various studies of reservoir rock and fluid surface properties and their relation to the different oil recovery processes. Several laboratory methods (1, 2, 3) ^l/have been used by different investigators to obtain a more fundamental understanding of the many factors which have an influence on the oil recovery from reservoir rocks"--Introduction, p. 1

Design, Construction And Characterization Of A 10-Liter Batch Pilot Plant Fermentor., Sylvester Ogden

Masters Theses

"A 10-liter batch type pilot plant fermentor has been designed and constructed. The design incorporated most of the desirable features of previous designs reported in the literature.

The stainless steel fermentor has a multi-speed agitator and aeration rates as high as 15 cubic feet per hour. Temperature indicating, temperature controlling, pH measuring, and automatic foam controlling systems are included in the design.

Sulfite oxidation rates have been determined for the unit at 15 operating conditions. A maximum sulfite oxidation rate of 1060 millimoles of oxygen per liter per hour has been obtained.

Fermentation using a Torulopsis utilis yeast culture has …

Investigation Of Zero Sidesway For Rigid Frames, Dolatray S. Mehta

Masters Theses

"This study was made to determine the location of a point at which a vertical load may be applied to a rigid frame structure and produce zero sidesway, the so called zero sidesway axis. For concentrated loads equations have been derived for zero sidesway. For uniform and triangular loads graphs showing zero sidesway for various ratios of column and beam stiffnesses and height ratios have been plotted"--Abstract, page ii.

The Submerged Culture Of Thiobacillus Thio-Oxidans In A Pilot Scale Fermentor, Edward Hibbert Crum

Masters Theses

"A strain of Thiobaci.llus thiooxidans was isolated from a West Virginia coal mine drainage. This strain was characterized by its production of sulfuric acid in shake flasks. The strain was also compared with a pure culture of h thiooxidans obtained from the American Type Culture Collection (ATCC number 8085).

The strain was grown in submerged culture in a 16-liter pilot scale fermenter. Two aeration systems, air and air enriched with carbon dioxide, were examined. The air enriched with carbon dioxide gave a much more rapid growth rate. The culture reached the mid-log phase of growth after 80 hours of incubation …

Ignition Time Lag: A Measure Of Explosive Energy Release, Paul H. Rydlund

Masters Theses

"By means of the resistance-element, or probe-wire, detonation-velocity measurement technique, explosive reactions from various blasting agents were studied. To reduce the number of variables, only standard AN-FO 94/6 mixtures were used, as are commonly employed today in constructions and mining operations. Accuracy of the data obtained was excellent, and the method proved itself not only relatively simple to operate but versatile in providing considerable information under many testing conditions. Studies of test records revealed the presence of a time-lag frequently occuring [sic] after primer detonation. Environmental factors such as confinement, charge diameter, primer size and energy content, and surface coatings …

Structural And Magnetic Characteristics Of The Belton Anomaly, Cass County, Missouri, Nagib Chamon

Masters Theses

"A vertical intensity magnetic survey of approximately 156 square miles in Cass County, central-west Missouri, revealed a broad circular anomaly whose magnetic relief exceeds 1000 gammas. Surface rocks are very gently inclined and are of Pennsylvanian age. Crystalline basement rocks are at a depth of approximately 2400 feet. Analysis of the data shows that the Belton anomaly consists of discontinuous smaller magnetic anomalies surrounding the central part of this broad anomaly. The central area of the Belton anomaly is occupied by a magnetic low. Analytical calculation showed that the source of the magnetic disturbance is at least 3650 feet below …

Solubility And Structure Studies Of Nickel (Ii) Acetate, Richard J. Baird

Masters Theses

"The effects of ammonium acetate on the solubility of anhydrous nickel (II) acetate in anhydrous acetic acid was investigated and was found to behave similar to the zinc (II), copper (II), and cobalt (II) systems. Problems with equilibrium, encountered by previous investigators, were overcome. The determination of the structure of nickel (II) acetate hemiacetate was atacked by infrared studies, preparation of adducts, cryoscopic studies, magnetic susceptibility measurements, and absorption spectra. It was found that nickel (II) acetate hemiacetate is octahedrally coordinated with two coordination sites vacant. It was shown that the binuclear cage structure common to copper (II), chromium (II), …

The Design, Construction, And Operation Of A Conducting Field Analog Computer., Richard T. Johnson

Masters Theses

"The purpose of this investigation is to design and construct a simple conducting field analog to solve problems described by the two-dimensional Poisson or Laplace equations. Decisions concerning choice of conducting media, construction of problem models, and design and construction of a specialized power supply with instrumentation were based on the results of previous experiments. Several problems are solved using the designed apparatus. Partial solutions to these problems are displayed in graphical form.

The greatest deviation of the experimental results from iterative values was consistently less than 8%. In most cases the deviation was less than 6%. The console arrangement …

On A Numerical Solution Of Dirichlet Type Problems With Singularity On The Boundary., Randall Loran Yoakum

Masters Theses

No abstract provided.