Digital Commons Network^™

Optimum Fin Spacing For Heat Transfer Per Unit Length Of Heat Exchange Section, Glenn Ellis Miller

Masters Theses

"This thesis presents the results of an experimental study of the heat-transfer ability of a finned surface as a function of the spacing between fins. The results are expressed as heat transfer per unit length of finned section rather than the heat transfer per fin. Circumferential steel fins, seven and three-quarter inches in diameter, were used for the investigation. Data was taken for fin spacings ranging from zero to one and one-half inches. The experimental heat-transfer rate to atmospheric air was determined by measuring the volume of saturated steam which condensed in the test section over a measured time interval. …

Velocity Profiles In Viscoelastic Drag Reducing Solutions, Luis Gustavo Florez E.

Masters Theses

"Turbulent velocity profiles in viscoelastic drag reducing solutions were measured using hot-film anemometer and Pitot tube techniques. Data were obtained in a solution of one per cent aluminium [sic] dioleate in toluene and in 0.2 and 0.4 per cent solutions of polyisobutylene (PIB) L-200 in cyclohexane. Velocity profiles were also obtained for comparison in toluene and cyclohexane by both techniques. By integrating the Pitot tube velocity profiles, large flow rate discrepancies between integrated and measured flow rates were found for the drag reducing polymer and soap solutions. This discrepancy was not observed in the hot-film anemometer measurements. The hot-film anemometer …

The Economics And Design Of Desalination By Evaporation Through Porous, Water-Repellent Membranes, Kuei-Hsiung Yang

Masters Theses

"The economics of desalination by evaporation through porous, water-repellent membranes has been studied in this investigation. Using reasonable assumptions this desalination process was found to be economical with the principal advantage being the simplification of multi-stage flash-type evaporation. Based on this process, two different methods were designed and studied by means of computer calculations for a 10 million gallons product water per stream day desalting plant. One method was based on a membrane evaporator and a heat exchanger and was designated Method I; and a combined evaporation-heat exchanger system was designated at Method II. The major factors affecting the economics …

Fault Detection In Combinational Networks, Alexander Rahm

Masters Theses

"This paper presents an algorithm for locating a failure in combinational logic networks, which is a problem of importance in the maintenance of computer systems. The procedure is based on the "path sensitizing" idea for fault detection. The networks considered are non-redundant, consisting of AND, OR, and NOT elements. The class of faults investigated is that which causes a connection to appear to be logically suck-at-one or stuck-at-zero, and only single failures are treated. It is shown that the failure is generally located to a specific "fault group"--Abstract, page 2.

The Acidic Transformaion Products Of Indoles Formed By Basidiomycetes, Chung-Ke Chang

Masters Theses

"A survey of the ability of basidiomycetes to convert tryptophan, tryptamine and indole acetic acid to other acidic indoles has been made.

The product formed from tryptamine by Tricholoma nudum was identified as indole acetic acid. The product formed by Cantharellus cibarius from D-tryptophan was identified as N-acetyl-D-tryptophan. The products were purified and identified by means of paper chromatography, thin layer chromatography, infrared spectroscopy and melting points.

The conversion of tryptamine and D-tryptophan was also studied in cultures of Leucopaxillus paradoxus, Hygrophorus conicus and Naucoria confragosa. H. conicus, L. paradoxus and N. confragosa transformed tryptamine and indole acetic acid into …

A Study Of Probability Of Error Calculations For Baseband Multi-Level Digital Transmission Systems Using The Fixed Threshold Decision Rule, Don J. Popp

Masters Theses

"This study is an investigation into analytical techniques used in deriving probability of error expressions for baseband multi-level digital transmission systems. A fixed-level decision rule is used to solve this statistical detection problem together with some simple concepts from probability theory. To illustrate these techniques, probability of error expressions are derived for the general uncoded system, a simple coded system, and a complex coded system. Curves of probability of error versus signal-to-noise ratio are plotted for the various systems considered"--Abstract, page ii.

Stress Analysis Of A Wall Footing Subjected To External Vertical Loads And Overturning Moments By The Finite Element Method, Adil Godiwalla

Masters Theses

"This investigation pertains to the stress analysis by the finite element method of a wall footing subjected to external vertical loads and external overturning moments. This problem has been reduced to a two-dimensional stress analysis problem by taking a unit length of the wall. A rectangular plate - element is used throughout this investigation. The development of the matrix equations is shown and the solution is performed by digital computer. Stresses in the horizontal direction show essentially linear variation which is in agreement with simple structural theory, while stresses in the vertical direction show severe perturbation near the column load. …

Mode Analysis Of The Unsymmetrically Fed Ground-Plane Aperture, John G. Hemmann

Masters Theses

"The problem of radiation from a waveguide-fed ground-plane aperture perturbed with a wedge-shaped dielectric insert was examined more carefully. The work initiated by Blumberg was continued, using a greater range of dielectric constants and smaller increments of angle.

Aperture field measurements were made over a range of dielectric constants for each wedge angle, in order to determine the change in amplitude distribution as a function of permittivity. Aperture phase measurements were also taken for selected angles. These were used with the amplitude data to predict, using numerical integration, the far-field radiation patterns of the perturbed aperture. Far-field patterns were then …

Vapor Pressure And Evaporation Coefficient Of Cadmium Oxide, R. Tom Coyle Jr.

Masters Theses

"Knudsen effusion experiments were carried out on CdO in fused silica crucibles at temperatures of 918°K, 1008°K with orifice areas from 2.742x10^-3 cm² to 30.52x10^-2 cm². The experiments were made in a molybdenum-wire, resistance-heated vacuum furnace. Several orifice areas were used at each temperature and reciprocal pressure versus orifice area plots were made. These plots yielded an upper limit to the evaporation coefficient of. 4.15x10^-2. An equilibrium constant for the vaporization reaction

CdO(s) = Cd(g) + 1/20₂ (g)

of

log Keq = 11.12 - 1.952x10⁴/T.

was obtained. Second and third …

Study Of Mass Transfer Through Porous Water-Repellent Membrane As A Function Of Membrane Thickness And Rates Of Heating, Yalamanchili Babu Rao

Masters Theses

"The object of this investigation was to study the mass transfer coefficients through porous water-repellent membranes, and their dependence on membrane thickness and rates of heating, and to compare experimental correlations with theoretically based equations. The membranes used during the experimental work were made of glass fiber treated with Teflon suspension and aluminum sulfate. The mechanism involves evaporation and condensation on opposite sides of a vapor-filled porous membrane. Salt water evaporates from one interface of a non-wettable, porous membrane, diffuses through the vapor filled pores, and condenses to fresh water at the other interface of the membrane. This transfer may …

Molecular Diffusion In Polymer Solutions By A Microinterferometric Method, Surendra V. Desai

Masters Theses

"The object of this investigation of molecular diffusion in aqueous polymer solutions was to study the effect of solute concentration on the differential diffusion coefficient and also to study the effect of polymer concentration on the mean integral diffusion coefficient. For this purpose a microinterferometric method was used. Two non-ionic, water soluble polymers, Carboxymethylcellulose (CMC) and Carboxypolymethylene (Carbopol), were used in the study with D-Glucose as a solute.

The differential diffusion coefficient was found to increase with increases in solute concentration in all cases. For CMC, the integral diffusion coefficient at first decreased with increasing polymer concentration but became constant …

Mineralogy And Paragenesis Of The Cave-In-Rock Fluorspar District, Hardin County, Illinois, Daesuk Han

Masters Theses

"The paragenesis of minerals occurring in the bedding-replacement fluorspar ores in the Crystal, Minerva No. 1 and Hill mines in the Cave-in-Rock district, Hardin County, Illinois, has been studied by underground, binocular, petrographic and ore microscopic examination. More than 300 hand specimens were collected from the mines, 100 thin sections were prepared and 36 polished surfaces were examined to prepare paragenetic diagrams for the Crystal and Minerva No. 1 mines.

The minerals determined in the fluorspar ores were: fluorite, sphalerite, galena, chalcopyrite, pyrite, marcasite, calcite, strontianite, witherite, barite, quartz, dolomite, oil and bitumen. Most of these minerals are present both …

Comparative Analysis Of Polynomial Root Finding Techniques, Charles Ray O'Daniel

Masters Theses

"The purpose of this study was to investigate and recommend various methods instrumental in finding the roots of a polynomial p(x) = 0. Many different methods are present today, and each has its advantages and disadvantages.

Through thorough investigation, the author has ascertained the key methods to be the method of Bisection, the Newton-Raphson method, and the Bairstow method. Special support in the form of algebraic theorems on the locations and kind of roots are extremely helpful. This combination of theorems and methods provides assurance, speed, and the ability to obtain complex roots.

The Bisnewbar method developed by this author …

An Investigation Of The Reaction Of Benzhydryl Chloride With Potassium T-Butoxide In Dmso, Lawson Gibson Wideman

Masters Theses

"The ultimate aim of this study was to elucidate the mechanism of formation of tetraphenylethylene from benzhydryl chloride and potassium t-butoxide in dimethyl sulfoxide. The development of a suitable technique for following the reaction rate and of an analytical method to determine the extent of the reaction became an important object in this project"--Introduction, page 2.

Dynamic Response Of A Simply Supported Beam To An Accelerating Point Load, Joseph Victor Cusumano

Masters Theses

"An analysis based on linear theory is presented for determining the dynamic response of a simply supported beam on an elastic foundation acted upon by a moving time dependent point force with axial forces included. This thesis extends the present theory to include an analysis of a point force accelerating uniformly across the beam. In particular, it is shown that the customary resonance conditions which are prevalent for a point force moving with uniform velocity no longer exist for the case of a point force accelerating uniformly across the beam.

The basic problem and its solution are presented for a …

Mechanisms Of Base-Catalyzed Reactions: Part Iii: The Acidities Of Some Hydroxylic Compounds In T-Butyl Alcohol., Charles Frederick Seger

Masters Theses

"The K_HA of water and five alcohols were determined in t̲-butyl alcohol employing sodium and potassium t̲-butoxides. The order of acidity is methanol>water>ethanol> 2-propanol~cyclohexanol>methanol. It was also shown that potassium t̲-butoxide was twice as strong a base as sodium t̲-butoxide. A spectrophotometric method was employed with p-nitroaniline as the indicator. Calculations were made employing the methods of Stearns and Wheland and of Hine and Hine"--Abstract, page iii.

Determining The Transfer Matrices Of Tapered Multiwire Transmission Lines, Clyde A. Vandivort

Masters Theses

"The advent of monolithic and integrated microelectronic circuits has aroused interest in passive multilayered thin film networks. The basic thin film network is shown in Figure 1. This structure consists of alternate resistive and dielectric layers sandwiched together. Such devices are referred to as distributed parameter RC networks. The reduction of volume and increased reliability offered by thin film devices has caused considerable effort to be extended in the analysis of their characteristics....

The incremental equivalent circuit given in Figure 2 stems directly from the above physical parameters and is the circuit used as a basis for the analysis that …

Basic Iron (Iii) Alkanoate Complexes, Young Hee Kim

Masters Theses

"Much information appears in the literature concerning the preparation, properties and structure of the basic iron (III) acetates...This study was initiated to prepare a number of the basic trinuclear iron (III) alkanoate complexes and to investigate the possibility of a common structure for all of these as suggested by the work of Orgel. The structural investigation was done on the basis of stoichiometric relationships, infrared spectra and magnetic moments"--Abstract, pages ii-iii.

A Study Of The Compressibility Of Silty Soils., Marvin L. Byington

Masters Theses

"This study has been conducted to determine the applicability of the Terzaghi Theory of Consolidation and to determine the compressibility of silt soils with varying clay content. A pure silt was extracted from the Lebanon Silt Loam and mixed with varying amounts of the Onyx Cave Illite-Chlorite Clay. The compressibility of these mixtures was determined and an attempt made to apply the Terzaghi Theory in the analysis. It was found that the compressibility of soils high in silt content is very low. It was also found that the Terzaghi Theory may be applied to mixtures of 15 percent or more …

Construction Of A Laboratory Type, Convertible Excitation Argon Laser, Arthur P. Reckinger

Masters Theses

"The purpose of this thesis is to describe the construction of a general purpose, convertable [sic] excitation, laboratory type, argon laser. Quartz tubing was used in the final model while attempts to use alumina were made during earlier work. The final model has total optical power output of 230 mw at a discharge current of 29 amperes in the dc excitation mode. Provision was also made to utilize RF or pulsed excitation. The device is built so that several values of optical transmittance are available with a wide range of mirror placement"--Abstract, page ii.

Effects Of Mixing Procedure Upon Uniformity Of Fibre Reinforced Concrete, Donald E. Nortrup

Masters Theses

"This thesis describes the effects of several methods of introducing wire fibres into a concrete mix upon the uniformity of wire fibre reinforced concrete. Various mechanical and manual methods of introducing the fibres were used and comparisons of the methods were based upon variability in splitting tensile strength and the quantitative distribution of the fibres as determined by visual inspection of sawed cylinders. Test results show that the tensile strength of concrete is increased appreciably by the inclusion of steel wire fibres in the mix and the uniformity of strength is similar to that of unreinforced concrete. The methods of …

A Programmed Synthesis Procedure For Asynchronous Sequential Circuits, Robert Judson Smith

Masters Theses

"The synthesis procedure for large asynchronous normal fundamental-mode sequential circuits is time-consuming and tedious when performed manually. This paper describes a series of computer programs which, given a machine specification in flow table form, automatically produces simplified normal form implementation design equations. The user may specify that either minimum-variable state assignments, or more rapidly generated near-minimum-variable codes be found. Next-state equations are formed using the generated state assignments and converted to simplified sums of products. Sample machines having flow tables of up to eighteen rows by four columns are synthesized"--Abstract, page ii.

Minimization And Generation Of Next-State Expressions For Asynchronous Sequential Circuits, Gary Keith Maki

Masters Theses

"One step in the synthesis procedure for realizing an asynchronous sequential circuit that is operating in fundamental mode is to obtain an internal-state assignment that will realize the operations of the circuit. Often the procedures that are used in accomplishing the above task generate several satisfactory assignments. The first part of this paper presents a method that will enable one to predict which of the internal-state assignments will yield a simpler set of next-state expressions. A second topic treated in this paper is one of presenting a method to generate the next-state expressions for an asynchronous sequential circuit directly from …

Scanning Properties Of Unsymmetrically Loaded Aperture Arrays, Gary Dean Brunner

Masters Theses

"Radiation patterns resulting from an array of waveguide-fed apertures, filled with assymmetrically [sic] cut dielectric inserts, in an infinite ground plane were investigated. The results of Blumberg and Hemmen concerning single apertures were applied to a two-aperture array, with emphasis upon obtaining an array capable of scanning in the far field through changes in the permittivity of the assymmetrically [sic] cut dielectric inserts. Scanning was shown to be possible with up to a 60⁰ scan angle with a "push-pull" method of varying permittivities, in which the permittivity of one insert is raised while the other is lowered. The aperture field …

Annealing Characteristics Of Neutron Irradiated Silicon Transistors, Joseph Robert Chott

Masters Theses

"When a transistor is subjected to neutron irradiation, a component of base current proportional to neutron fluence is induced. From the effects of annealing on the base and collector currents, the conclusion was drawn that there is an apparent difference in the annealing characteristics between the neutral and the space-charge regions of the semiconductor device. This study of the anomalous annealing indicates that the neutron-induced component of base current is a result of one, or a combination, of the following mechanisms: a quasi-tunneling recombination phenomena in the emitter-base space-charge region, or an influence of the p-n junction electric field on …

The Measurement Of Explosively Induced Stresses In Rock-Like Materials With A Capacitive Transducer, Vincent Paul Crane

Masters Theses

"A capacitive transducer was developed for measuring the free surface motion in Hydrostone blocks loaded by an explosive plane wave generator approximately one foot from the specimen. The charge to specimen distance was adjusted to produce a single spall, the position of the fracture being noted on the recovered specimen. The longitudinal wave velocity in each specimen was determined by the ultrasonic pulse technique before each shot. From the above measurements the stress, strain and strain rate at the point of fracture were determined. An attempt was made to determine the actual fracture time with imbedded [sic] conductive graphite rods, …

Noble Gases In The Earth And Its Atmosphere, Robert Anthony Canalas

Masters Theses

"Abundance of noble gases extracted from Fig Tree Shale exhibit a marked deviation from the gas content of eclogitic rocks purported to be mantle material. The abundances of the heavy noble gases in shale were found to exceed the highest known meteoritic values. The abundances of the lighter noble gases were found to be comparable to the abundances of these gases in typical chondrites.

Temperature gradient analyses show that excess heavy gases are released at low temperatures. This is interpreted to indicate a preferential adsorption of the heavy noble gases on fine-grained sediments when these gases were being released from …

A Subsurface Geologic Study Of Petroleum Possibilities In The Pennsylvanian Rocks Of Concho County, Texas, Gregory Paul Kraus

Masters Theses

"During early Pennsylvanian time the area now occupied by Concho County was a portion of the Texas peninsula, a broad, low arch with a karst topography developing on its exposed Ellenburger surface. A mid-Pennsylvanian marine transgression inundated the arch and it became an area of clear, shallow water deposition favorable to limestone development. Local sedimentation during Strawn time was largely controlled by its position relative to the Llano uplift and surrounding basins. A variety of subsurface maps were constructed for this study essentially utilizing electric log data. The results indicate that limestones of the Strawn platform facies rapidly change in …

Programmed State Assignment Algorithms For Asynchronous Sequential Machines., Wayne L. Schoeffel

Masters Theses

"An important step in the synthesis procedure for realizing a normal fundamental mode asynchronous sequential circuit is the internal state assignment. Although systematic methods have been developed to construct minimum-transition-time state assignments, they become long and tedious with hand methods for machines with more than 7 or 8 internal states. To extend the application of these algorithms to larger problems, this paper presents an efficient digital computer program for generating minimum-variable state assignments. An alternate program is also presented which, though shorter, does not guarantee a minimum-variable assignment"--Abstract, page ii.

The Relation Of Heat Transfer To Mass Transfer In Vaporization Through Porous Membranes., Chung-Liang Yeh

Masters Theses

"The object of this investigation was to study the mass and heat transport phenomena through porous, water-repellent membranes. The investigation concerned the rate of vaporization of salt water at a porous membrane surface, mass transfer of vapor through the pores of the membrane, condensation of vapor on the other surface of the membrane in contact with a coolant (fresh water), and the undesired heat transfer by conduction through the membrane. The water-repellent membrane separated the two liquid phases by surface tension forces and provided a vapor phase in its pores. Membranes made of fiberglass and Teflon had been found suitable …