Digital Commons Network^™

The Influence Of Silt On The Compressibility Of An Illitic Clay, James Inman Spencer

Masters Theses

"This study was undertaken to investigate the effect of varying amounts of clay (illite) on the compressibility of a silt as it may be found in nature in a normally consolidated deposition. Laboratory procedure was designed to minimize sample disturbance so as to obtain, as nearly as possible, a virgin consolidation curve. By varying the amounts of silt and clay in a given sample, and sedimenting the sample from a soil-water suspension, consolidation test analyses were used for a comparison of the various samples. Results revealed that between sample mixtures of 40 and 60 percent silt there was a relatively …

Geochemical Abundance Of Iodine, Jane Hanisch Bennett

Masters Theses

"The research reported herein includes unpublished iodine and uranium data on a group of United States Geological Survey standards and on a group of ultrabasic rocks. Data are also included for the major rock types, deep sea sediments, and for graphite and troilite inclusions in iron meteorites. Tellurium data for the troilite are also reported. Appendix I is a literature article (Bennett and Manuel, 1967a) on Canyon Diablo Graphite. Appendix II is a literature article (Bennett and Manuel, 1967b) on deep sea sediments. The results of this study show that most of the earlier estimates of the crustal abundance of …

A Simulation Of The Transistor By Computer Using The Linvill Diffusion Model, Clifford D. Skouby

Masters Theses

"This investigation involves the construction of an analog computer model of the transistor. The computer model is based upon the Linvill diffusion model. The equations for the Linvill diffusion model were programmed on the computer by making certain approximations. Different models, using different approximations, were used for the different regions of operation of the transistor. A composite analog model was constructed by combining the models for the restricted regions, giving a general model good for all regions of transistor operation. This analog diffusion model was modified to account for the effects of junction capacitance and base resistance. The modified analog …

Permeability And Additive Sorption And Extraction In Lubricating Greases, Chan-Shan Fan

Masters Theses

"The effect of the area and type of surface of ten silica thickeners and aluminum oxide on grease permeability, on the sorption of PAN [Phenyl-α-naphthylamine] by the grease, and on subsequent extraction were studied. For grease containing 6% per cent of thickener, permeability coefficients varied from 20.1 x 10⁻¹¹ cm² to 168 x 10⁻¹¹ cm². For each silica type they decreased with increase in surface area of the thickener. The level of the permeability coefficient is generally related to the worked penetration. In sorption measurements using permeating oils of varying PAN concentration, the amount of PAN associated with the thickener …

An Unsteady-State Method For Determining The Thermal Conductivity Of Materials, Richard H. Bulmer

Masters Theses

"Originally this work was initiated to develope [sic] a method for measuring the thermal diffusivity and thermal conductivity of metals. Due to the characteristics of the method and the equipment used, it was concluded that the technique is not suitable for materials of high conductivity. However, results show that the apparatus is valuable for the determination of the thermal diffusivity of relatively poor heat conductors. The favorable characteristics of the method are its rapidity and basic simplicity"--Abstract, page ii.

Electric Field Investigations And A Model Of Electrical Spraying Of Liquids, Wallace Deshon

Masters Theses

"The equation E = [2 V] [over] [N 1n(4d/N] has been used for determining the electric field at the liquid tip in electrical spraying of liquids. Data were taken at the instant of spraying in an attempt to experimentally verify this equation. The results indicate that the value given by the equation needs to be increased by about 20% in the normal range of operation. A model for the spraying mechanism of the liquid is also proposed"--Abstract, page ii.

A Formal Description Of The Scc 650 Digital Computer, Hardy J. Pottinger

Masters Theses

"The requirements of a descriptive language for automated digital computer design are presented. Y. Chu's Computer Design Language is then used to describe the logic of the SCC 650, a small general-purpose digital computer at UMR. Chu's language is found to be the best language available to the designer for both documentation and automatic translation into Boolean Equations"--Abstract, page ii.

An Ultrasonic Pulse Generator Using The Transducer As A Frequency Determining Element, Donald E. Watke

Masters Theses

"This paper describes the development of a method of ultrasonic pulse generation in which the transducer determines the frequency of oscillation. A definite advantage of this method is the ability of the frequency of oscillation to change with changes in the transducer mechanical resonant frequency. This maintains peak efficiency at all times. The method is demonstrated in a small sonar transmitter but could be applied to any area involving driven ultrasonic transducers"--Abstract, page ii.

Electronic Transitions In Diatomic Molecules, James O. Hornkohl

Masters Theses

"The electronic transition moments of many band systems have been found to be linear functions of the internuclear distance. However, some band systems exhibit a quadratic variation of the transition moment. In these quadratic cases, the plots from which the variation of the transition moment is determined are based upon the approximation of the second r-centroid by the square of the first r-centroid. The square of the first r-centroid does closely approximate the second r-centroid by a simple error analysis shows that the small difference between the two is not a quantitative measure of the error introduced into the transition …

Effects Of Pressure On The Mechanical Properties Of Magnesium, Joseph George Hoeg

Masters Theses

"The data collected in an attempt to evaluate the pressure dependency of the mechanical properties of extruded AZ31B-F magnesium alloy are presented herein. This information was compiled from the results of compression tests run in hydraulic fluid environments pressurized to 50,000 psi, and tension tests run in the atmosphere. Specimen axial load and longitudinal strain were recorded and converted to effective stress and effective strain parameters for presentation. The term pressure is defined, in this report, as the negative average of the principal stresses or, essentially, the negative of the hydrostatic component of stress. The effective stress and strain, at …

An Analysis Of Dirac Delta Generated Spherical Waves In An Infinite Maxwell Medium, William F. Breig

Masters Theses

"It is an accepted fact that the simple Maxwell and Voigt models do not usually represent the behavior of real materials. In order to make the results of a model more realistic, other combinations of springs and dashpots must be considered. To understand the more complicated models, it is desirable to have a knowledge of the Maxwell model since this element usually occurs either in series or in parallel in the advanced models. This investigation reports solutions of the spherical wave equation in both the elastic and viscoelastic media. Laplace transform techniques are used to obtain the parameters; stress, velocity, …

Sulfide Mineralogy And Fabrics Of The Iron Ores At Benson Mines, New York, Pedro Hugo TumialáN De La Cruz

Masters Theses

"The occurrence of sulfide minerals and their textural relationships to the silicate and oxide minerals in the Benson Mines, New York, iron deposit were investigated by ore microscopic and petrographic means. The Benson deposit is one in which the dominant iron oxides, magnetite and hematite, occur in a quartz-feldspar gneiss which was subjected to hornblende granulite subfacies metamorphism. Two hundred ore and country rock specimens were systematically collected from all parts of the open pit mine. Polished sections and thin sections were prepared from nearly all of the collected specimens. The oxide ore exhibits a granular texture in which isolated …

Design Of A Sequential Detector, Scott William Abel

Masters Theses

"The communication engineer has in the past treated the detection problem from a limited point of view. Detectors have been designed to reach a decision based on a specified number of samples. This approach has proved valuable, but it offers no provisions for an early decision if a conclusion becomes obvious early in the sampling. Neither is there an opportunity for additional sampling if necessary to reach a definite conclusion, because of these limitations it is desirable to find more general detectors. This study looks at a specific statistics (the sign test) and designs a sequential detector to utilize this …

Pressure Welding Of Continuously Cast Nodular Iron, Gerald W. Wille

Masters Theses

"The objective of this study was to determine the feasibility of using pressure welding as a joining technique for swaged nodular iron.

Test pressure welds were produced with swaged continuous cast nodular iron at temperatures between 1750⁰F and 2050⁰F with welding pressures between 15,900 psi and 51,400 psi using an induction coil to heat the weld zone.

Pressure welds of greater strength than the as-received nodular iron were produced by swaging the material before welding. The optimum welding parameters were a temperature of 2050⁰F with a welding pressure of 46,700 psi.

On the basis of these tests it is concluded …

Synchronization Of Pulse Code Modulation Telemetry, Lawrence J. Mueller

Masters Theses

"Pulse Code Modulation (PCM) is one of the most widely utilized radio telemetry techniques for the recovery of test data from aerospace vehicles. Synchronization of the receiver with the transmitted data is perhaps the prime requisite of a PCM telemetry system. In this paper the frame synchronization process is analyzed by developing equations which define the three modes of synchronizer operation (SEARCH, VERIFY, and LOCK) in terms of the relative probabilities of operation. The criteria employed to optimize the synchronization process are the mean time to acquire true synchronization, the probability of true synchronization after verification of the synchronization decision, …

A Computer Adaption Of Plastic Analysis For Rigid Frames, Gerald Duane Galloway

Masters Theses

"A computer program for the plastic analysis of rigid frames is presented. The program is based on the virtual work method of plastic analysis. The great number of failure mechanisms that must be considered in any virtual work analysis are given in Appendix C. The use of the program as a design aid is also discussed. A check for the virtual work program is also presented. The check is based on the method of inequalities as initially presented by Symonds and Neal"--Abstract, page ii.

A Study Of Bifeo₃ And The Hall Effect In Bifeo₃ And Cds, Fred Hoerger Taylor

Masters Theses

"Pure samples of BiFeO₃ were heat treated in oxygen and nitrogen atmospheres in an attempt to reduce the conductivity of the samples. Dielectric constant and dissipation factor measurements, as a function of frequency, were made to determine whether the samples had been altered. A special high temperature Hall effect apparatus was constructed. Using this apparatus an upper limit for the Hall mobility in BiFeO₃ was established. The apparatus was also used for room temperature measurements of Ga-doped CdS samples. Resistivity measurements to be used with the Hall effect results were made on both the BiFeO₃ and the CdS samples. Hot-Point …

Design And Testing Of A Downhole Continuous Wave Generator, Cole L. Smith

Masters Theses

"The continuous shear wave generator was designed to be the first instrument capable of producing a continuous high frequency signal below the weathered layer of the earth. This is to be accomplished by placing the instrument in a bore hole and lowering it below the weathered layer where the higher frequencies are severely attenuated. The generator produced a measurable signal output with the output force being approximately 11 pounds force. Testing of the generator showed the necessity of using a spring system with a low natural frequency. The testing also indicated several improvements which should be made in the generator …

Coupled Transport Of Heat And Mass In Laminar Tube Flow, Lung-Mau Huang

Masters Theses

"The object of this investigation is to study the mutual dependence of heat and mass transport in laminar and hydrodynamically developed tube flow. Consideration is given to gas flow through a tube whose wall is coated with a sublimable materials so that heat and mass transfers take place between the wall and the flowing gas stream. The tube wall is thermally insulated from the external environment, with the result that the latent heat required by the sublimation process at the wall is supplied solely by convective transfer from the gas. The analysis of the problem requires simultaneous solution of the …

Measurement Of Demagnetizing Factor Of Ring-Core, Subhashchandra Chimanlal Patel

Masters Theses

"A method has been presented to measure the demagnetizing factor of ring-cores. First the incremental apparent permeability and the incremental true permeability were measured at different degrees of saturation and then the demagnetizing factor was determined from those results. The cores used were tape would ring-cores of mean length of 8.0 cm. The method was found suitable for cores with 1/4 mil or thicker tape, but was in question for the 1/8 mil tape core tested"--Abstract, page ii.

Evaluation Of Methods For Analysis Of Multi-Degree-Of-Freedom Systems With Damping, Brijgopal R. Mohta

Masters Theses

"A general review of various methods for studying the behavior of linear lumped parameter systems with viscous damping is presented. Five methods are discussed. These are: (1) Normal Mode Technique (2) Ho's Method (3) Impedance Method (4) Graphical Technique (5) A Method for Reducing Degrees-of-freedom. For solution of vibration problems by the Normal Mode Technique, the systems are classified as (1) classically damped or (2) non-classically damped. It is shown that the classically damped systems are relatively easy to solve. For non-classically damped systems, the method proposed by K. A. Foss has been employed. This method is quite complex, but …

A Development Of Regression Models For Predicting Temperature, Salinity And Sound Velocity In Sea Water, Darwin Wayne Brown

Masters Theses

"There are in existence today some reasonably good numerical procedures for predicting sound velocity, but these procedures require that certain initial data such as temperature and salinity be given before a sound velocity may be computed. Eliminating the need for on-location observations of temperature and salinity, which are used in computing sound velocity, was the primary objective of this study. Stepwise multiple regression was applied in the search for suitable models to predict temperature and salinity, and ultimately sound entirely in terms of controllable variables, such as latitude, longitude, depth, and day-of-year"--Abstract, page ii.

A Comparison Of Three Numerical Techniques Used For The Solution Of The Two-Point Boundary Value Problem, William Richard Krall

Masters Theses

"Three numerical approximation techniques, called the Initial step, Shooting, and Direct Finite Difference Techniques, respectively, are compared and discussed as they apply to the solution of both linear and non-linear boundary-value problems of the form y"=f(x,y,y') with endpoint conditions y(x_o)=y_o and y(x_n)=y_n. The techniques are compared with respect to speed and accuracy by comparing the solution of each problem considered four times, each time for a different increment value, and comparing the errors at four pivotal points chosen at equally spaced distances over the domain of the function, to give an indication of …

Surface Interactions Between Nickel Ions And Sodium Dodecyl Sulfate, Ralph Edward Coleman

Masters Theses

"In this research the interaction of nickel ions with the surfactant sodium dodecyl sulfate at the liquid-air interface was studied. Surface tension measurements were performed on pure sodium dodecyl sulfate solutions, with and without the addition of nickel ions. Results of these measurements showed that the addition of nickel ions lowered the equilibrium surface tension values of pure sodium dodecyl sulfate solutions and shifted the critical micelle concentration to lower concentrations. The foam fractionation technique was used to determine if the nickel ions could be removed from surfactant solutions. It was found that the removal of nickel ions was influenced …

Analytical And Experimental Methods For Determining The Properties Of Materials At Very High Rates Of Loading, A. G. Behring

Masters Theses

"In the following report, some of the properties of ALCOA 7075 T651 aluminum, when subjected to high rates of loading, are experimentally investigated by impacting two rods of the material longitudinally. One rod is accelerated to a uniform velocity with an air gun launcher. The stationary second rod is instrumented with strain gages on its lateral surface in order to determine the strain-time history following impact. A detailed description of the experimental equipment is included. Simple, one-dimensional theory is used to determine the dynamic, elastic modulus of the test material under the impact condition. Several observations regarding the behavior of …

The Design Of A Hybrid Computer System, James Joseph Becker

Masters Theses

"Three typical hybrid computers in industry and educational institutions are presented. The hybrid computer designed and built at the University of Missouri at Rolla consists of an SCC-650 digital computer, a TR-48 analog computer, and a hybrid interface. The interface permits the digital computer to control the modes of operation on the analog computer. There are also 9 multiple-pole relays on the interface that can be controlled by the digital computer. A 320 hold removable patchboard is included in the interface. There are 40 trunks lines from the analog computer that are present on the patchboard. The 4 digital-to-analog channels …

Determination Of Molecular Diffusivities In Liquids, Pai-Chuan Wu

Masters Theses

"A porous plate, initially at a uniform solute concentration is immersed in a well-stirred pure solvent bath of known volume. It is desired to find the molecular diffusivity of the solute-solvent system by observing the change of the solute concentration in the solvent bath with time. In this study, concentration-time data were curve-fitted by non-linear, least squares techniques to the various mathematical solutions describing molecular diffusion in the porous frit. This technique is used to determine the diffusion coefficient and predict the value of other parameters existing in the different mathematical diffusion models. The results from the different models are …

Lattice Parameters, Coefficients Of Thermal Expansion, Densities, And Lattice Perfection Of The Copper-Indium Primary Solid Solutions, Lin Sheng Yu

Masters Theses

"Precise measurements of lattice parameters and densities of the alpha-phase Cu-In solid solutions were made at temperatures of 25°C. The thermal expansion coefficients between 15 and 65°C, the solid solubility of In in Cu at 650°C, and the soundness of crystal structure resulting from alloying were determined. The Cu-In alloys were prepared from high purity (99.999%) Cu and In by melting both metals inside evacuated quartz tubes. The solidified alloys were annealed and then examined by X-ray for homogeneity...The slowly solidified alpha-phase alloys gave densities lower than the theoretical (X-ray) values due to the presence of shrinkage microporosity. This density …

The Geology Of The Thayer Area Emphasizing The Stratigraphy Of The Cotter And The Jefferson City Formations, William Jesse Hedden

Masters Theses

"Detailed geologic mapping of the Cotter-Jefferson City formational contact in the Thayer, Missouri area demonstrates the feasibility of using this contact. This mapping also delineates significant faulting in the area.

The stratigraphy of the Cotter and Jefferson City formations in the Thayer area has been studied to find a mappable contact between the two formations. The contact was mapped in this area by using marker beds, the stratigraphic positions of which were determined by applying insoluble residue techniques to outcrop sections. Because the insoluble residue zones of the Cotter and Jefferson City formations are recognizable throughout the state of Missouri …

Drag Reduction In Hydrocarbon Soap Solutions, Ian Radin

Masters Theses

"Turbulent flow pressure drop measurements were made for solutions of aluminum dioleate (soap) in toluene at concentrations of 0.2, 0.5, 0.75 and 1.0 per cent. Tube diameters ranged in size from 0.01 to 2.0 inches. The results of these measurements differed from those observed in aqueous systems. Higher concentrations (at least 0.75 per cent) were required before drag reduction was observed. Although fresh solutions were somewhat sensitive to shearing, once a solution was over about two weeks old it showed little further mechanical degradation. Although in the toluene solutions, wall shear stresses were reached which were over an order of …