Digital Commons Network^™

An Evaluation Of The Placement Service At Eastern Illinois University, Charleston, Ill., Gary E. Price

Masters Theses

No abstract provided.

A Study Of Hot Shortness In Steels, Koang-Hwa Kung

Masters Theses

"In this investigation an attempt was made to study the deformation of a number of laboratory-melted and commercial steels. A compressive load was applied to the steels at constant temperature and also during heating. The amounts and rates of deformation in these two types of tests was not consistent: in the constant temperature tests the hot short steels deformed more than the others while they appeared to deform less during heating. Metallographic examination of the sulfides indicated that the sulfides in cast steel are not stable and that they change during heating and hot working"--Introduction, page 2.

The Effect Of Copper Upon The Eutectoid Reaction In The Zinc-Aluminum System, Paul Theodore Corcoran

Masters Theses

"A Leitz dilatometer was used to study the kinetics of the eutectoid reaction in the zinc-aluminum system and the effect of small additions of copper upon this reaction. Three alloys were investigated: a pure 78% zinc - 22% aluminum alloy; a 78% zinc - 21.9% aluminum - 0.1% copper alloy; a 78% zinc - 21% aluminum -1.0% copper alloy. It was found that this reaction was similar to the pearlite reaction in the iron-carbon system. The reaction occurred by diffusion processes and the products of the reaction looked similar to pearlite when examined under the microscope. Copper was found to …

The Kinetics And Mechanisms Of The Reaction Of Benzyl Chloride With Potassium T̲-Butoxide In T̲-Butyl Alcohol, Der-Rong Chen

Masters Theses

"Benzyl chloride is a moderately reactive halide. Substitution of the Cl⁻ by other nucleophiles, e.g., HO⁻, AcO⁻, S₂O₃⁻, Br⁻ etc. proceeds almost quantitatively in solutions at convenient temperatures ... The object of this study was to investigate if the less basic t̲-butoxide in t̲-butyl alcohol would afford the same product, viz., stilbene; and, if so, by what mechanism. A study of the products and kinetics of the interaction between benzyl chloride and potassium t̲-butoxide in t̲-butyl alcohol therefore has been initiated"--Introduction, page 1.

A Measurement Of Dead Space And Its Effect On The Homogeneous Nucleation Rate Of Water Vapor In Helium, Michael A. Grayson

Masters Theses

"The existence of a "dead space" surrounding each nucleated water droplet is demonstrated and measurements of its rate of development are made. The effects of this "dead space" are considered to be due to both the removal of vapor from the helium-water vapor mixture and the evolution of heat about the drop due to its growth. The results confirm the usefulness of the concept of a "dead space" and provide a means for its measurement with respect to time. Recommendations for further study and a method of correcting for dead space effects is given"--page [i].

Thermal Degradation Of Poly (Methyl Methacrylate) In Solution In Various Solvents, Ya-Chih Chen

Masters Theses

"A study has been made of the thermal degradation of poly (methyl methacrylate) of different molecular weights in toluene, ethyl acetate and chloroform. Four poly (methyl methacrylate) samples having molecular weights of 2,210,000, 733,000, 320,000, and 43,00, respectively were studied in this investigation. The results indicated that the polymer having a molecular weight of 2,210,000 undergoes degradation while the low molecular weight polymers having molecular weights of 733,000, 320,000, 43,000 undergo reverse polymerization"--Abstract, page [ii].

The Effect Of Small Alloy Additions On The Quench Induced Texture Of Alpha Uranium, Kenneth Ray Riggs

Masters Theses

"The preferential orientations produced in binary alloys of U-Si and U-Cr on plane sections perpendicular to the direction of heat flow by cooling from beta-phase temperatures were determined. The experimentally determined textures were presented using inverse pole figures. A definite and reproducible relationship was found to exist between the preferred orientation present at any position and the cooling rate which material at the position had experienced. It was found that the concentration of the alloying elements within the ranges studied had little detectable effect upon the observed relationship between the cooling rate and the resulting preferential orientation. It was postulated …

Effects Of Internal Pressure Upon The Buckling Of Thin Circular Cylindrical Shells Under Axial Compression, Leroy E. Thompson

Masters Theses

"An experimental investigation was made of the effects of internal pressure upon the buckling of thin circular cylindrical shells under axial compression. A comparison was made of the experimental and theoretical results; the latter were derived from the large-deflection theory. Results showed that the internal pressure had an appreciable strengthening effect upon the buckling of the cylindrical shell. The comparison showed that the experimental results were lower than the theoretical results for a given internal pressure. The discrepancy between the results can be expected since there were factors not included in the theory: imperfections, end conditions, lengths, and material irregularities"--Abstract, …

The Separation Of Radioactive Technetium And Zirconium By Electrodialysis And A Study Of The Behavior Of Technetium In Aqueous Solutions, William Victor Andoe

Masters Theses

"The rapid increase in radioisotope applications necessitates improved technology for separation and purification of the fission product elements. Electrodialysis techniques employing Permutit anion exchange membrane(3148) were used to separate technetium from zirconium. The method was based upon the stability of the pertechnetate ion in alkaline solutions and the precipitation of zirconium from alkaline solutions. The separation of radiotechnetium and radiozirconium was effected with a two cell electrodialysis unit employing an anion exchange membrane. The solution medium consisted of fluoride and nitrate ions which were made basic with sodium hydroxide. The minimum basicity for a good separation was 0.1N NaOH"--Abstract, page …

Field Permeability Determination Of Partially Saturated Fine Grained Soil, Edward G. Rapp

Masters Theses

"The determination of water permeability through a soil is necessary to estimate seepage losses from small reservoirs. At the present time, the methods available to conduct this determination in partially saturated fine grained soils are expensive and in most cases not commensurate with the cost or importance of the individual structure. This investigation was conducted to evaluate the use of a proposed, potentially inexpensive field procedure in this situation. A modified borehole apparatus was utilized in field tests to determine the permeability of a partially saturated soil deposit in place. Undisturbed samples from the same location were tested in the …

Equivalent Circuit Of Unsymmetrical Inductance Diode Using Linvill Lumped Model, Donald Lawrence Willyard

Masters Theses

"Integrated circuit techniques and applications are rapidly changing the electronics industry. A problem common to both state-of-the-art approaches to integrated circuit fabrication is that of miniaturizing and integrating inductors. It is found that, for a certain range of injection current levels, certain unsymmetrically doped junction diodes have an inductive small-signal impedance. This thesis discusses the theory of inductance diodes and applies finite difference equations and the Linvill lumped model to the differential equations that describe their carrier flow processes. The static I-V characteristic and the small-signal equivalent circuit at high injection densities are derived. The elements (R,L,C) of this equivalent …

Permeability And Additive Absorption And Extraction In Lubricating Greases, Eugene Hsiung-Jen Tu

Masters Theses

"A permeability apparatus was used to measure the permeability coefficients of eight Lithium-Calcium greases and ten Baragel greases in which the viscosity and type of the oil component were varied. The oil present in each grease was used for its permeability measurement.

An improved sample packing technique was developed to improve the repeatability of permeability measurements. Repeatability of ± 3% was achieved. In general the permeability coefficients of the non-soap Baragel greases were higher than those of the lithium-calcium greases with comparable oil components, and those of greases containing paraffinic oils were higher than these containing naphthenic oils. The effect …

A Study Of The Photomechanical Effect In Silicon, Ronald M. Oglesbee

Masters Theses

"This paper presents the results of an experimental investigation into the photomechanical effect in silicon. The effect was found to be very similar to the electromechanical effect. In both cases the phenomena observed is the softening of a thin surface layer of the material when it is either illuminated or when a current is flowing through the material. An anisotropy was observed in both the hardness and the photomechanical effect. Increasing temperatures tended to "washout" the photomechanical effect. The surface hardness and the photomechanical effect were found to depend heavily on proper surface preparation of the samples, however little dependence …

Stability Determination By Liapunov's Method In Nonlinear Control Systems, Neng-Chung Liao

Masters Theses

"An introduction to Liapunov's second method as it applies to control system stability is presented in this work. Main theorems and definitions of Liapunov's method are treated. In particular, Lur'e's method and Szego's method for testing the stability of a nonlinear system are presented, and several examples are used to illustrate these procedures"--Abstract, page ii.

Use Of Spent Sulphite Liquor For Stabilization Of Fractured Rock And Sealing Off Water Bearing Formations, Laxman Singh Sunda

Masters Theses

"The paper industry, in its process of manufacturing pulp from wood, produces large quantities of a substance called lignin, lignin sulphite, or lignosulphonate. This material has been disposed of as a waste product; however, it does have many potential uses. In this investigation, lignosulfonates were used as agents for bonding rock sections together and, as the chief component of gels, for filling the pores of artificial rock cores. The purposes of these tests were to find how this substance could be used in the mining industry, for stabilizing fractured ground around mine openings and for sealing off water influx into …

Effect Of Calcium Lignosulfonate On Properties Of Concrete At Early Ages, Lawrence Kong-Pu Wang

Masters Theses

"The objective of this investigation was to determine the effects of calcium lignosulfonate on the physical properties of concrete. Calcium lignosulfonate used as an admixture was tested for its effect on the tensile and compressive strength of plain concrete cylinders, and for its effect on the flexural strength of plain concrete beams. The effect of the admixture on shrinkage, slump, air content and unit weight was also studied. the test results showed that calcium lignosulfonate reduces the amount of water required to make a workable concrete mix; a more workable mix saves money because it is easier to place, thus …

Solid Solubility Of Sulfur, Selenium, And Tellurium In Molybdenum At 1100°C, Lattice Constants Thermal Expansion Coefficients, And Densities Of Molybdenum And The Molybdenum-Base Alloys, Ramesh Purushottamdas Shodhan

Masters Theses

"With the ever increasing requirement for engineering materials having adequate mechanical properties at ever higher temperatures there has been, in quite recent years, a considerable increase in the study of molybdenum and molybdenum-rich alloys. Since 1945 extensive information on the engineering properties of molybdenum and molybdenum-base alloys has gradually become more available ... The present work involves the determination of solid solubility of elements with large atoms such as sulfur, selenium, and tellurium in molybdenum at 1100°C using the parametric method. Furthermore, the thermal expansion coefficients of pure molybdenum and of molybdenum-base solid solutions containing the elements just mentioned were …

The Effect Of Nickel On Activated Sludge, James Robert Matthews

Masters Theses

"The primary objective of this investigation was to determine the effect of nickel on activated sludge over a comprehensive range of concentrations and to evaluate the ability of the sludge to acclimate and become more tolerant to the metal. Six one-liter fill and draw activated sludge units were fed domestic sewage; five of these units also received constant, increasing, and shock doses of nickel while the sixth was maintained as a control. Treatment efficiency was evaluated in terms of the chemical oxygen demand, suspended solids, and nickel content of the effluent. A Warburg respirometer was also employed and was operated …

Detection Of Stress Corrosion Cracking In U-Bend Brass Specimens By An Electro-Mechanical Method, Floyd Elwin Loftin

Masters Theses

"An apparatus was designed and built which held two u-bend specimens. When the specimens were exposed to a corrodent, losses in strength were detected as a result of stress corrosion cracking. The apparatus was used to study time to failure of cartridge brass u-bend specimens exposed to ammoniacal copper sulfate solutions which varied in pH. A minimum time to failure, 1.06 hours, was detected at pH 7.2. The maximum time to failure, for the range studied, was 28.36 hours at pH 7.7.

No useful data were obtained in the range from pH 6.6 - 6.8. thick, black surface coatings were …

The Effect Of Cadmium On Anaerobic Digestion, Lyle Lynn Pruitt

Masters Theses

"The main purpose of this study was to determine the effect of cadmium on anaerobic digestion. Metal concentrations in the form of regular and slug doses were considered. The possibility of acclimating anaerobic bacteria to higher cadmium levels was studied, and attempts were made to reestablish digestive action through re-seeding in digesters overcome by high cadmium concentrations"--Abstract, page [ii].

Thin Film Resistor Deposition, Rollie R. Herzog

Masters Theses

"Thin film techniques may be the key to future miniaturization of electrical equipment. The purpose of this thesis was to develop procedures for deposition of thin film resistors and to test these deposited resistors. Starting with a vacuum system, equipment was designed and built to hold and heat the substrate, monitor the substrate temperature and deposited resistance, and to evaporate the material to be deposited. Resistors were deposited and tested for resistance between resistors, capacitance between resistors, and resistance of resistors. A heat aging test was also used comparing resistors with and without a silicon monoxide coating"--Abstract, page ii.

The Design Of A Sensitive Probe For Mass Flux Measurements Of Water Vapor In Air, Devendra Vaikunthlal Mehta

Masters Theses

"This investigation pertains to the construction and investigation of a sensitive probe to determine the possibility of measuring the mass flux of water vapor in air under non-flow steady state conditions. The probe was a small electrolysis cell is which the electrolyte (partially hydrated phosphorus pentoxide) was used as the sensing element. The rate of mass transfer was determined by measuring the amount of direct current flowing through the acid film"--Abstract, page i.

A Second Study Of Homogeneous Nucleation Of Water Vapor In Helium, Raymond J. Schmitt

Masters Theses

"Absolute homogeneous nucleation rates in a supersaturated mixture of water vapor and helium are measured using a long sensitive time expansion chamber and a method devised by Kassner and Allard. A pulse technique is employed to produce the nucleation in an effort to suppress disturbing influences of vapor depletion and droplet growth. The time-varying nature of the supersaturation during the nucleation pulse is taken into account by an Integration over the pulse. Observed and theoretically predicted droplet concentrations are related by an assumed nucleation rate law which is adjusted until the total droplet populations predicted by integration of the assumed …

The Effect Of Varying Sea Coal Fineness On Sea Coal Activity In Molding Sands, Laurence A. Cooley

Masters Theses

"An experiment was conducted in an attempt to establish a relation between sea coal activity in a facing sand and the particle size of the sea coal added to the sand. It was felt that if a sufficient difference in distribution of volatiles was detected, a correlation between particle size and activity of the sea coal within the test specimens might be established. The lack of positive evidence to support such a relationship is indicative that a variation in particle size does not promote volatile re-deposition within the range of particle sizes investigated for the particular weight per cent of …

The Eccentric Orifice As A Flow Measuring Device In Small Diameter Pipes, James E. Casale

Masters Theses

"This thesis reports and evaluates the use of an eccentrically placed orifice as a flow measuring device in small pipe sizes. The orifice is placed in a concentric location and moved to increasingly eccentric locations until full eccentricity is reached. At full eccentricity the circumference of the orifice is tangent to the circumference of the pipe. The effects of increasing eccentricity are evaluated for four orifices...Flow coefficients for the orifices in different locations are plotted against Reynolds numbers. The eccentric orifice is a reliable, accurate flow measuring device for metering or controlling the flow of fluids. Design criteria can be …

Maximum Present Value Calculations With Digital Computers, James Boyd Robison

Masters Theses

"This paper discusses maximum present value calculations for a mineral property using digital computers. A semi-quantitative mathematical model to optimize operating conditions is considered. The model is based on a modified cash flow analysis. Many variables affect the solution, and their effect upon present value is described. Selected data (mining rate, costs, reserves, metal sales price, and others) for a hypothetical open pit copper mine are used in a set of solutions for present value. The results are discussed in detail. It is concluded that: (1) Digital computer methods are rapid and useful, (2) Changes in the mining rate, average …

A Graphical Method Of Estimating Heat Capacities Of Hydrocarbons, Pu-Ying Liu

Masters Theses

"Heat capacity arises because the individual particles comprising a substance are able to move and thus take up kinetic energy and usually also potential energy as the temperature rises. In many substances electrons do not absorb energy until very high temperatures are reached. Thus most heat capacity effects are interpreted in terms of the motion of the atoms neglecting electronic transitions. The total internal energy of a material is, therefore, equal to the sum of the energies due to translational and rotational motion of the molecules and to the vibrational motion of the atoms making up the molecules...The objective of …

Finite Difference Solution For Triangular Plates, Hao-Yang Huang

Masters Theses

"In this thesis the finite difference method is used to solve triangular plates with uniformly distributed transverse load. As a matter of convenience triangular coordinates are used. The supporting conditions as well as the shape of plate are varied. All calculations are performed by digital computer. The patterns of differential operators in triangular coordinates, the deflections of plates, and the moment distributions are shown and discussed. The results obtained for some special cases are compared with published solutions"--Abstract, page i.

Measurement Of Stray Load Loss Of D.C. Machines, Kanaiyalal Ramanlal Shah

Masters Theses

"For many years the standard practice, in calculation of conventional efficiency of d.c. machines, has been to include stray load losses as equal to 1% of the output. This assumption may be true for large, compensated d.c. machines but it is known to be small for smaller, uncompensated, general-purpose, industrial-type machines of open design. An A.I.E.E. Committee on Rotating Machines was formed to investigate whether the present practice of assigning 1% for the stray load loss is justified or not. They reached a conclusion, reported in 1949, after investigating 243 stray loss tests on different motors ranging from 1/2 hp …

Drop Growth In A Supersaturated Vapor, Roger Buecher

Masters Theses

"Using kinetic theory and the thermodynamics of phase transitions, a method is derived for finding the growth rate and temperature increase of a droplet in water vapor which has been supersaturated by the expansion of a cloud chamber. Calculations are performed for a specific numerical example and compared to other work in this field"--Abstract, page [2].