Digital Commons Network^™

An Evaluation Of Potomac Community Consolidated School, Dean L. Myers

Masters Theses

No abstract provided.

Anodic Dissolution Of Lead In Aqueous Solutions, Christopher Kuo-Chieh Wu

Masters Theses

"The apparent valence of lead was determined in one normal solutions of potassium nitrate, ammonium acetate, lead nitrate, and lead acetate at temperatures of 25 and 50°C. The current density was varied from 0.001 to 1.00 amp•cm ^-2. The apparent valence of lead ranged between 1.90 and 2.00 in all solutions. The lower valences were reached at higher current densities. The amount of disintegration was very small, and was dependent upon film formation on the surface of the anode.

Potential-current density relationships for the anodic dissolution of lead were obtained in the electrolytes mentioned above. In potassium nitrate and …

The Kinetics Of The Reaction Of M-Nitrobenzyl Bromide With Hydroxide Ion In Aqueous-Aprotic Solvent Mixtures, Ramesh Nagindas Sheth

Masters Theses

"The reaction between m-nitrobenzyl bromide and sodium hydroxide in homogeneous aqueous dioxane and aqueous tetrahydrofuran media was studied.

The product of the reaction was identified by infrared, gas chromatography and chemical tests as m-nitrobenzyl alcohol.
The kinetics of the reaction are second order with practically no variation in the rate constants as the % of the organic solvent was changed in the medium. This seems to imply hydrolysis of the organic halide by a process involving both bond-breaking and bond-formation in the transition state.
The activation energy, measured in 50% aqueous dioxane, between 20⁰ and 69.5⁰C at 5 different temperatures, …

Checking Rigid-Framed Structures By Extended Moment-Area Equations, Lucky Li-Chi Chow

Masters Theses

"Using the known moments obtained from the moment distribution solution, the extended moment-area equations are used to check whether or not delta x, delta y, delta theta are truly zero, or are any other quantity they are supposed to be. In order to get a reasonably correct answer, a solution must meet both the elastic checks and the static checks for their equilibrium and compatibility functions. Using the extended moment-area equations, the magnitudes of the slopes and deflections at all of the joints in framed structures can be found easily"--Abstract, page ii.

A Photoelastic Study Of The Stresses In A Deep Beam Using Partial Mirrors For Isochromatic Fringe Sharpening And Fringe Multiplication, Edward M. Raney

Masters Theses

"This paper is a photoelastic investigation of the stresses in a deep beam using partial mirrors to obtain isocromatic fringe sharpening and fringe multiplication. This method may be of particular value in photoelastic work for obtaining full field fringe multiplication and fringe sharpening for models which exhibit low fringe orders.

The photoelastic model used in this investigation is a deep beam with a length to depth ratio of one. A uniform load is applied over the center one-half of the beam. The beam is supported by two uniform loads distributed over a length of one-quarter the span.

A first approximation …

Modal Characteristics Of A Vibrating Truss, Edd Leighman Ghent Jr.

Masters Theses

"In this thesis, a complete technique is presented for the vibration analysis of any planar structure which can be classified in the broad category of trusses or frames. Although a theoretical backdrop is included for the' sake of completeness, the intent is to provide a technique that is readily adapted to computer usage and can be handled with a minimum of confusion or misunderstanding.

The problem is solved by the use of a displacement technique wherein the inertia and stiffness properties of a structure are calculated by superimposing the contributions of each component of the structure. The calculation of these …

Slope Stability Analysis Of A Fissured Glacial Clay, Byron G. Walker

Masters Theses

"A slope in an over-consolidated, fissured clay was analyzed by the Swedish Method of Slices.

Values of cohesion (c) and angles of friction (Ø) were determined by three different types of direct shear tests (undrained, drained and residual).

Factors of safety (functions of c and Ø) indicated that the direct shear test parameter gave a factor of safety approximately four times that represented by failure conditions in the field. Drained tests gave a factor of safety nearly 2.3 times the value represented by field conditions. The conclusion is made that these two tests are of limited value for slope stability …

Absolute Soft X-Ray Dosimetry For Radiation Chemistry Studies, Howard Sajon Joyner

Masters Theses

"A homogeneous, variable plate separation ion chamber consisting of a polyethylene body and employing flowing ethylene as the cavity gas has been designed and tested for the specification soft x-ray (<75kV) energy deposition in typical hydrocarbons. The variable plate separation feature provided primary data on the differential specific ionization originating within the cavity gas occupying the effective collector volume which is independent of inherent chamber inhomogeneities associated with the electrically conducting films comprizing the chamber electrodes. These data demonstrated that charged particle equilibrium is established within the first few ten thousandths of an inch in typical solid hydrocarbons irradiated with this class of sources. Comparison of this type of chamber with a fixed plate separation, static cavity gas mode of operation showed that the latter may predict dose rates with inherent errors exceeding 100%. With the quality of electronic readout accessories presently available, the variable plate separation chamber yielded dose rate data exhibiting a probable error of 3.8 percent (plus the unknown uncertainty in the literature data on the energy required to form an ion pair), and an ultimate limiting error of less than 2 percent appears feasible"--Abstract, page ii.

An Investigation Of Failure Patterns Of Layered Specimens Loaded In Uniaxial Compression, Narendra Y. B. Choudary

Masters Theses

"Uniaxial compressive strength for two and three-layered specimens was obtained with different thicknesses of layers and also for different length to diameter ratios. The fracture and failure pattern was studied. Shear and extension fractures were observed in the layers. Geometry and end conditions of the specimen had a great influence in the failure and fracture pattern.

The uniaxial compressive strength of a layered specimen was found to be lower than the weighted average strength and either low or high when compared to the arithmetic average strength, depending on the ratio of the heights of the layers. The compressive strength of …

Study Of Mass Transfer Through Porous, Water-Repellent Membranes, Virendra V. Tanna

Masters Theses

"A new method of desalination using a porous, water-repellent membrane was studied. The membrane utilized surface forces to support a vapor phase in its pores which separated the salt water from fresh water. The method used a vapor pressure difference across the membrane as the driving force for mass transfer of water from the salt water phase to the fresh water. This vapor pressure difference was obtained by maintaining a temperature difference between the two liquid phases.

The experimental data and results indicated the feasibility of vaporization through porous, water-repellent membranes. The flux of water through a membrane made of …

A Study Of The Development Of A Heuristic Program That Solves Symbolic Laplace Transformation Problems, Arthur E. Zackrison

Masters Theses

"A medium-speed general purpose digital computer (IBM 1620 Model II) was programmed to solve symbolic Laplace transformation problems. Although the applied mathematician and modern engineer has many uses for the symbolic solution of a problem, the potential of symbolic manipulation by a computer has not yet been sufficiently developed to help them because of many problems. This paper discusses the program and based on the author’s experience with it’s [sic] performance, clarifies the position of several of these difficulties and reaches some conclusions concerning computer solution of such problems"--Abstract, page ii.

Empirical Evaluation Of The Eccentric Orifice In Small Diameter Pipes, Gary A. Hinz

Masters Theses

"This investigation has taken different orifice sizes (0.3005", 0.4000", 0.5045", 0.6015") and tested their flow characteristics when used in a 1" diameter pipe. Each orifice was initially placed in a fully eccentric position, that is the circumference of the orifice was placed tangent to the inside circumference of the pipe. Data was taken with the orifice eccentric to concentric in increments of 0.050".

Plots of flow coefficient versus Reynold's number were made for each position of the four orifices tested.

Empirical equations were developed for determining the flow coefficient of the various orifice sizes placed in any eccentric position.

It …

Catalytic Effects On Radiation-Induced Polymerization Of Methyl Methacryalate, David E. Bartine

Masters Theses

"A study has been made of the effect of Kaolin clay particle size and acidity on the degree of radiation-induced polymerization of methyl methacrylate. The results indicate that the degree of polymerization varies with the clay particle size, and that the amount of polymer produced is influenced by the pH of the clay"--Abstract, page ii.

A Study Of The Effect Of Magnetite Additions To Shell Molds On The Surface Quality Of Low Carbon Steel Castings, Robert C. Tooke

Masters Theses

"Shell molds containing additions of ten to fifty percent magnetite, Fe₃O₄, of various particle sizes were cured by induction heating. For comparison, regular shell molds were made using silica and zircon sand. Low carbon steel was cast into all of the molds.

Castings produced from the regular shell molds exhibited poor surfaces due to mold expansion. Magnetite additions eliminated the expansion defects from the casting surfaces.

Excellent surfaces were obtained on the low carbon steel castings with proper selection of the magnetite particle size and the percent of magnetite added. Improper combinations of size and amount …

Nucleate-Boiling Heat Transfer To Water At Atmospheric Pressure, H. D. Chevali

Masters Theses

"The purpose of this investigation was to study the hysteresis effect, the effect of micro-roughness and orientation of the heat-transfer surface, and the effect of infra-red-radiation-treated heat-transfer surfaces on the nucleate-boiling curve.

It has been observed that there exists no hysteresis effect for water boiling from a cylindrical copper surface in the nucleate-boiling region over the range studied. The nucleate-boiling curve has been found to be independent of micro-roughness and orientation of the heat-transfer surface. There was no detectable change in the nucleate-boiling characteristics of the heat-transfer surface when the surface was treated with infra-red radiation"--Abstract, page ii.

Correlation Of Drag Reducing Data In Dilute Polymer Solutions, Jorge Mario Rodriguez

Masters Theses

"The purpose of this investigation was to obtain a correlation for drag reducing solutions in circular tubes under turbulent conditions. Data were taken for three polymer-solvent systems: polymethyl methacrylate V-100 (M_v ~ 110,000) in toluene, polyisobutylene L-200 (M_v ~ 4,700,000) in toluene, and polyisobutylene L-200 in cyclohexane. The data from the two polyisobutylene systems, together with other data on polymethyl methacrylate G (M_v ~ 1,500,000) in toluene and polyisobutylene L-80 (M_v ~ 860,000) in cyclohexane, were used to attempt to obtain the correlation. The V-100 solutions were not used because they were not drag reducing.

The …

The Anodic Oxidation Of Crotonic Acid In Basic Solutions, Richard C. Porter

Masters Theses

"The purpose of this study was to investigate the anodic oxidation of crotonic acid in basic solutions. Potassium hydroxide solutions of pH 12.3 and KOH-K₂CO₃ solutions of pH 11.5 and 10.5 were used. The investigation was carried out on platinized-platinum anodes at 80°C.

Experimental studies were conducted to determine the effects of crotonic acid concentration, pH, and temperature on the current. Faradaic efficiency was determined by analysis of CO₂ produced and was approximately 100 per cent.

The results were interpreted in terms of a mechanism having the following characteristics:

1. The first electron transfer is the rate …

The Effect Of Concentration On The Viscosity Of Polyisobutylene Solutions, Lung-Yu Chou

Masters Theses

"In the past twenty years the viscosity of dilute polymer solutions (i.e., where the solute molecules are far apart) has been investigated in great detail, both theoretically and experimentally. The viscosity characteristics of such systems are well-understood.

Only a few studies have been made of the effect of concentration on the viscosity of polymer solutions in the concentration range where the polymer molecules begin to overlap. This range of concentrations is important in practical applications such as dry spinning of fibers, cross-graded automotive motor oils and in many industrial formulations where polymers are used to thicken solvent vehicles. Development of …

An Investigation Of The Limitations Of The Antenna Range At The University Of Missouri At Rolla, Ronald Earl Nelson

Masters Theses

"The University of Missouri Antenna Range is described and criteria on range components for acceptable operation are discussed. Discussion of the results of an experimental investigation of component systems of the antenna range is presented. Experimental results are compared to criteria for acceptable operation and recommendations for the improvement of the facility is made. Suggestions are made as to its usage at higher frequencies"--Abstract, page ii.

A Study Of Sedimentation In A Well Regulated Major Drainage Basin - The Monongehala, Allegheny And Upper Ohio Rivers, William S. Wood

Masters Theses

"This investigation is concerned with the study of various programs employed in reducing and controlling sediment. The measures employed by the U.S. Soil Conservation and Forestry Services to control and reduce erosion, the primary source of sediment, was studied. The flood control and river navigation structures constructed and operated by the U.S. Army Corps of Engineers and the effect of these structures on sedimentation was also evaluated. State and local community regulation and control of exploited natural resources was studied to determine their influence on the generation and control of sediment.
The Allegheny, Monongehala and upper Ohio River Drainage Basin …

Location Of Maximum Moments In A Continuous Two Span Beam Due To Moving Loads, Thomas Houng-Yn Yang

Masters Theses

"The objective of this investigation is to determine the positioning of vehicle wheels so as to cause maximum positive and negative moments in a two span continuous girder. Several variables are considered, namely, the ratio of loads to each other, the distance between wheels, and ratio of one span length to the other. The necessary equations are derived and the results, after being programmed on a computer, are shown in a series of curves.

These curves serve as a tool for the designer, enabling him to arrive at design moments by simple substitution in the appropriate moment expression, within the …

A Nonlinear Sampled Data Feedback Control System Employing Pulsed Thrust Position Control, John D. Corrigan

Masters Theses

"This thesis shows that reaction jet thrust pulses, each of constant amplitude and time duration, in conjunction with sampled data error information can provide satisfactory position and/or attitude control for space vehicles.

Incremental phase-plane analysis of the system yields a technique for determining system response and suggests a means of compensation. Control system response for the vehicle under the influence of external forces is shown to be satisfactory by digital computer simulation"--Abstract, page ii.

The Effect Of Combined Torsional And Bending Loads On A Channel Beam With One End Restrained From Warping, David M. Schaeffer

Masters Theses

"Channel beams have been designed with the main purpose of giving large resistance to bending while the torsional strengths are known to be relatively small. In this experiment, a cantilevered channel beam was loaded with a concentrated load at the free end, first through the experimentally determined shear center and then through the centroid of the cross section. For each loading condition, the strains were measured with the aid of SR-4 strain gages placed at intervals along the length of the beam. With the aid of a computer, the strains were converted into longitudinal stresses and these stresses were compared …

Modification Of The Hydraulic Jump By Submerged Jets, Edward Leon Tharp

Masters Theses

"Tests were performed in order to determine the effect of submerged jets injecting water into the base of the hydraulic jump. The jump was studied in terms of the following properties: specific energy of the flow leaving the hydraulic jump, length of the hydraulic jump, tailwater depth, and wave formation properties. These properties for the hydraulic jump with submerged jets were compared to the natural hydraulic jump.

Results of the tests indicate that: submerged jets at any angle tested tend to decrease the specific energy of the water leaving the jump and are more effective than the impulse-momentum principle indicates, …

Minimum Cost Data Collection Techniques For Circulation Control At The University Of Missouri At Rolla Library, John Peter Shewchuk Sr.

Masters Theses

"Data collection is beginning to assume increased importance in the field of data processing. This thesis investigates a method for quantitatively selecting a portion of the library to place on an automated circulation control system that uses data collection as an entry into a data processing system.

The circulation function of the library was considered to be an inventory problem. Titles were considered as items of inventory and circulation of that title was considered to be a "sale" of that item. The IMPACT method was used to distribute items (titles) in a sample by age. Various ages were found to …

Analysis Of Sand Asphalt Mixtures, Maurice A. Sayegh

Masters Theses

"The objective or this investigation was to determine the optimum percent of asphalt which should be added to the sand asphalt mixture. Also the effects of filler on the properties or the sand-asphalt mixture were evaluated.

The variables in this study were mineral filler, asphalt cement, and asphalt content. The sand used in this study was sub-rounded, and uniformly graded. The asphalt was asphalt cement with two different penetrations, one of 85-100 penetration grade and the other of 120-150 penetration grade.

Three different groups of mixtures of sand-asphalt were prepared. The first group consisted of adding 85-100 penetration asphalt to …

A Crystallographic Study Of The Pbzro₃-Pbtio₃-Bifeo₃ Ternary System., Dannie R. Clarida

Masters Theses

"The purpose of this investigation was to conduct a crystallographic study of the PbZrO₃-PbTiO₃-BiFeO₃ ternary system, where all three components are perovskites. Lead zirconate is antiferroelectric, lead titanate is ferroelectric, and bismuth ferrate is thought to be ferroelectric. X-ray diffraction analysis was employed to determine the crystallographic structure and lattice parameters.

A tetragonal region was found to exist in the area of high PbTiO₃ content. A rhombohedral region occurred in the remainder of the system with high BiFeO₃ and PbZrO₃ content, except for an orthorhombic envelope along the PbZrO₃-BiFeO₃ side of the diagram up to approximately 70 per cent BiFeO₃.The …

A Study Of Modified Plug Designs For A Globe Valve, Robert W. Wagner

Masters Theses

"This thesis presents an empirical study of the characteristics of a cylindrical skirted disk valve used as a flow regulating device. Holes were drilled in two separate removable cylinders, which, when respectively attached to the valve plug adapter, provided control of the flow rate. These cylinders could be moved to permit exposure of more or less flow area by means of the valve stem and crank mechanism. At the closed position of the valve no holes were available for flow within the differential pressure zone of the valve, while at the full-open position all the drilled holes were within the …

Stable Predictor-Corrector Methods For First Order Ordinary Differential Equations, Terrell Lester Carlson

Masters Theses

"Because of the wide variety of differential equations, there seems to be no numerical method which will affect the solution best for all problems. Predictor-corrector methods have been developed which utilize more ordinates in the predictor and corrector equations in the search for a better method.

These methods are compared for stability and convergence with the well known methods of Milne, Adams, and Hamming"--Abstract, page ii.

The Development Of A Modified Soil Shear Vane, Vernelle Truman Smith

Masters Theses

"The purpose of this investigation was to determine how the soil shear graph could be modified to measure more accurately values of shear strength of fine-grained, cohesive soils. Several modifications were tried, however, the one that gave the most satisfactory results consisted of a vane and base plate mechanism.

A red clay of high plasticity obtained from a local cave was tested in both the natural or undisturbed state and in the remolded state. The only variable was the moisture content. Compaction effort was the same for all remolded specimens. Tests were conducted on undisturbed samples taken with thin walled …