Digital Commons Network^™

Comparison Of Experimental And Numerical Results For Flexural Capacity Of Light-Gage Steel Roof Deck, Christopher H. Raebel, Dawid Gwodzdz

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The objective of this paper is to present a comparison between experimental results to each of two numerical analyses of cold formed steel roof deck in flexure. Prior numerical studies using the Direct Strength Method (DSM) and the Equivalent Width Method (EWM) have shown discrepancies between results obtained by the two methods. The goal of this research initiative was to compare results from each of the two numerical analysis methods to experimental results in an effort to determine which numerical method is most appropriate for analyzing steel deck in flexure.

Twenty-four physical tests were conducted using four different deck gages …

The Design And Development Of Lightweight Composite Panels For Rigid Wall Structures, Jeremy J. Artman, Cheng Yu

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The paper presents a research effort aimed at developing a stronger, lighter, and more economic shelter for both military and civilian use. Reported herein are the research results on developing solid wall panels using cold-formed steel corrugated sheathing and members, as well as polyurethane spray foam for insulation. This research includes calculating uniform load density, determining the overall strength of the panel, and investigating the flexural strength of the roof panels. Research incorporated different connection methods, with varied stud spacing, to determine the safest design for the new mobile facilities. Previous research has shown that cold-formed steel corrugated sheathing performs …

Experimental Study On Uplift Capacity Of Purlins Considering Restraints From Standing Seam Roof Systems, Wei Luan, Yuanqi Li

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A total of 32 specimens of single-span purlin roof assemblies considering uplift wind load were tested to investigate the structural behavior of cold-formed steel purlins with one flange fastened to standing seam roofs. Failure modes and failure loads of purlins with different parameters were obtained. Full finite element models, incorporate purlins, clips and standing seam roof panels, were developed, and the analysis results were consistent to a high degree with the test results. Using the same element type and material model, the rotational restraint of test roof systems and corresponding influence factors were investigated by finite element models. Finally, using …

A Finite Element Study Of Corrugated Steel Deck Subjected To Concentrated Loads, Vitaliy V. Degtyarev

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

An extensive parametric study was initiated to get a better understanding of steel deck behavior under concentrated loads and to develop design recommendations for a wide range of deck profiles. This paper presents first results from the study related to 1.5-in. deep roof decks of types B and F. The study was performed on non-linear finite element models of deck validated against available test data. Deck gage, span length, span condition, concentrated load locations along and across the deck span were varied in the study. The observed deck behavior under concentrated loads, as well as the effects of the studied …

Web Bearing Capacity Of Cold-Formed Ferritic Stainless Steel Unlipped Channels With Web Perforations Under The End-Two-Flange (Etf) Loading, Amir M. Yousefi, James B. P. Lim, G. Charles Clifton

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Laboratory and numerical evaluations on the web bearing capacity of unlipped cold-formed ferritic stainless steel channels are described in this paper. The channels considered have circular perforations in the web and are loaded under the end-two-flange (ETF) load case. A total of 387 results comprising 27 laboratory and 360 numerical results are presented. A nonlinear quasi-static finite element (FE) model was developed for the numerical investigation. An extensive parametric study is described to determine web bearing capacity reduction factors for different sizes of circular web perforations and cross-section dimensions; the circular web perforations are either centred or offset to the …

Web Crippling Behavior Of Cold-Formed Ferritic Stainless Steel Unlipped Channels Under Interior-One-Flange And End-One-Flange Loadings, Amir M. Yousefi, James B. P. Lim, G. Charles Clifton

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The web crippling strength of cold-formed ferritic stainless steel unlipped channels subject to interior-one-flange and end-one-flange loading is considered in this paper. A total of 144 results are presented, comprising 36 laboratory and 108 numerical results. These results cover the cases of both flanges restrained and unrestrained to the load and reaction plates. Unlike other work in the literature, the numerical analysis in this paper uses nonlinear quasi-static finite element analysis with an implicit integration scheme, which has advantages over static and quasi-static with an explicit integration scheme analyses, particularly for post buckling predictions of unlipped channels subject to web …

Experimental And Analytical Studies Of Cold-Formed Steel Sections With Edge-Stiffened Circular Holes Subjected To Web Crippling, Asraf Uzzaman, James B. P. Lim, David Nash, Amir M. Yousefi, Benjamin Young

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel sections are often used as wall studs or floor joists and such sections often include web holes for ease of installation of services. The holes are normally punched or bored and are unstiffened; when the holes are near to points of concentrated load, web crippling can be the critical design consideration. Recently, a new generation of cold-formed steel channel sections with edge-stiffened circular holes has been developed. The web holes are stiffened through a continuous edge stiffener/lip around the perimeter of the hole. In this paper, a combination of experimental investigations and non-linear finite element analyses are used …

Parametric Studies And Design Recommendations Of Cold-Formed Steel Sections With Edge-Stiffened Circular Holes Subjected To Web Crippling, Asraf Uzzaman, James B. P. Lim, David Nash, Amir M. Yousefi, Benjamin Young

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A parametric study of cold-formed steel sections with edge-stiffened circular holes subjected to web crippling under one-flange loading condition was undertaken using finite element analysis. The effect of different hole sizes, edge-stiffener length and distances of the web holes to the near edge of the bearing plate on the web crippling strengths of channel sections were investigated. The web crippling strengths are influenced by various geometry parameters: the ratio of the hole depth to the flat portion of the web, a/h, the location of the hole as defined by the distance of the hole from the edge of the …

A Preliminary Study On Stainless Steel Hollow Flange Beams Featuring Lateral-Distortional Buckling, Shuang Niu, Zhidong Zhang, Feng Fan

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

To explore the potential of using stainless steel structurally, extensive research has been carried out to study the structural behavior of stainless steel member as associated with the nonlinear stress-strain relationship. Hollow flange sections feature improved structural efficiency and a unique issue of web distortion. Steel hollow flange sections have been studied and commercially distributed (e.g. the very first HFB section and lately LSB section). As a proactive study, this paper investigates stainless steel hollow flange beams of double-symmetric section with numerical modeling and parametric analysis. The validity of the idealized FE model was verified with existing study on steel …

On The Effect Of Web Stiffening Of Cold-Formed Steel Thin-Walled Lipped Sigma Sections In Compression Members, Rashideddin Cheraghi, Hamidreza Mohammadzadeh

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel cross sections are high strength thin-walled profiles which are highly prone to local and distortional instabilities. Stiffening techniques are utilized in the industry as a solution to enhance local and distortional buckling strengths. The sigma section is that channel section which its web pushed inward for the stiffening reason. In this research, the effect of side sway of the web (dx) on the buckling behavior of lipped sigma sections is investigated. The results demonstrate that stiffening inclined components of the web in lipped sigma sections for dx up to 0.5512”(14 mm) act as a stiffener and change the …

Bracing Design For Torsional Bucking Of Cold-Formed Steel Wall Stud Columns, C. D. Moen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A method is presented for calculating the required brace stiffness and strength to limit torsional buckling deformation in cold-formed steel wall stud columns. The bracing (bridging) design method utilizes recent insight from classical stability solutions that define twist of singly and doubly-symmetric columns with an initial twist imperfection as a function of column compressive load. A wall stud design example is provided.

Behavior Of Beam To Column Cold-Formed Section Connections Subjected To Bending Moments, Maged T. Hanna, Mohamed M. El-Saadawy, Ghada M. El-Mahdy, Ehab H. A. H. Aly

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold formed sections are often used in the construction of mid-rise buildings due to their high strength weight ratios, and fast erection. In these buildings, the connections between joists and studs are mainly simple connections. However, application of these sections can be extended to moderate span frames where connections between members are subjected to bending moments. Strength and stability of such frames depends to large extent on the behaviour of the connections between their members. Over the last twenty years, several researchers undertake tests on cold formed section connections subjected to bending moments. Major of them classify the connections as …

Investigation On Shear Capacity For Screw Connections Of Cold-Formed Steel Framed Shear Walls With Steel Sheathing, Ruoqiang Feng, Ying Ma

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Experimental and numerical investigations were carried out to learn the shear capacities for screw connections of cold-formed steel framed shear walls with steel sheets for the base layer combined with gypsum wallboards for the face layer. The design methods of test specimens, the loading equipment and the data processing method were introduced. According the phenomenon of tests for multiple self-drilled screw connections, the loading-deformation curves, shear capacity and failure modes were testified. The influence of end distance of screw, edge distance of screw, diameter of screw, spacing of screw, thickness of steel sheets, thickness of gypsum wallboards, thickness of studs …

Cold-Formed Steel Bolted Moment-Resisting Connections With Friction-Slip Mechanism For Seismic Areas, Marzie Shahini, Alireza Bagheri Sabbagh

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper presents investigation on cold-formed steel (CFS) beam-to-column moment-resisting (MR) bolted connections with high energy dissipation capacity suitable for seismic areas. Bolting friction-slip mechanism of the introduced CFS MR connection is developed as its main seismic energy dissipation fuse aiming to postpone or eliminate local buckling and yielding in the CFS MR connections. Finite Element (FE) modelling techniques are employed to effectively simulate the connections with an activated friction-slip mechanism. Hysteretic energy dissipation response of the connections with circular bolting (CB) arrangement designed to slip at 0.5Mp are presented. Based on the obtained FE results, full-scale physical tests on …

Planning The Future Of North American Cold-Formed Steel Design Standards, Benjamin W. Schafer, Jay Larson, Helen Chen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Growth in cold-formed steel structures has long been tied to developing and advancing the engineering standards that govern their use in construction. The American Iron and Steel Institute (AISI) has taken a leadership role in this activity in North America since 1946. Conventional standards providing closed-formed solutions to member capacity, such as the recently completed suite of AISI Standards in 2015 and 2016. These standards have reached an impressive level of maturity given the complexity of designing entire (building) structural systems out of steel that is rarely greater than 2mm thick. However, the demands on the structural engineer designing cold-formed …

The Impact Of Bearing Conditions On The Behavior Of Cold-Formed Steel Stud Assemblies, Abbas Joorabchian, Zhanjie Li, Kara D. Peterman

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The objective of this study is to explore the structural response of cold-formed steel stud assemblies (i.e., stud and track) with partial bearing conditions. It is hypothesized that studs bearing under partial bearing conditions (i.e., not fully bearing on a concrete slab) may result in reduced axial capacities. Currently, the behavior of these systems on concrete slabs due to member instabilities is not well-understood, and cold-formed steel design specifications provide no guidance. This study provides an integral experimental and numerical investigation of the stability response of the studs under partial bearing conditions in order to quantify the reduction of their …

Behavior Of Cold-Formed Steel Metal Industrial Buildings, Adrianna M. Early, M. Ebrahim Mohammadi, Richard L. Wood, Kara D. Peterman

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper presents research focused on understanding the observed behavior of cold-formed steel (CFS) metal buildings during Hurricane Harvey, which made landfall Friday, August 25, 2017 between Port Aransas and Port O’Connor, Texas. Through the Geotechnical Extreme Event Reconnaissance (GEER) association (funded by the National Science Foundation) a team of structural engineers and researchers performed rapid and detailed assessments of structural damage caused by the hurricane. The National Science Foundation gathered photographs, damage assessments sheets, and three-dimensional laser point cloud data of severely damaged cold-formed steel industrial buildings. The Port Aransas County Airport experienced severe damage to several cold-formed steel …

Sustainability Of Modular Lightweight Steel Building From Design To Construction, Ornella Iuorio, Loredana Napolano, Luigi Fiorino, Raffaele Landolfo

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The increasing concerns over population growth, depletion of natural resources and global warming as well as catastrophic natural events is leading the international scientific community to envisage sustainability as a crucial goal. The built environment plays a key role on the triple bottom line of the sustainable development -- Planet, People, Profit -- because of several environmental, social and economic impacts produced by the construction sector. The acknowledged need to promote a sustainable building market is an international high-priority issue as underlined by the 2030 Agenda for Sustainable Development. Indeed one of its strategic objectives highlights to make cities and …

Experimental Study Of Apex Connection Stiffness And Strength Of Cold-Formed Steel Double Channel Portal Frames, J. Peng, J. Bendit, H. B. Blum

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel portal frames are an increasingly popular structure in the housing and industrial sectors, and are commonly used for garages, sheds, and shelters. Longer span cold-formed steel portal frames are relatively new to the market, and as a result limited design guidance and recommendations exist, including the strength and stiffness of the connections. The apex connection stiffness affects the distribution of internal actions and deflections of a portal frame, and therefore, it is necessary to quantify the apex stiffness for use in design models to accurately determine the frame behavior. An experimental program was carried out on a series …

Shear Resistance Mechanisms On Steel Sheet Shear Walls With Burring Holes And Cross-Rails, Yoshimichi Kawai, Kazunori Fujihashi, Shigeaki Tohnai, Atsushi Sato, Tetsuro Ono

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Steel sheet shear walls with burring holes are employed in low and mid-rise buildings in seismically active regions. A configuration with burrs on the inside enables the thinner wall and omitting the machining of equipment holes. The effects of cross-rails which are generally designed to strengthen the bearing capacities of the studs, on 2.73~4.53m height shear walls were clarified by finite element analysis and experiments. Post-buckling behavior depends on tension fields restrained by the cross-rails. The formulas of the allowable strengths and the indexes of ultimate strengths were developed using the mechanisms.

Cold-Formed Steel Framed Shear Wall Database, Deniz Ayhan, Samuel Baer, Zhidong Zhang, Colin A. Rogers, Benjamin W. Schafer

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The objective of this paper is to provide an introduction to a recently compiled database of cold-formed steel framed shear wall tests and demonstrate the application of this database for improving the understanding and modeling of cold-formed steel framed shear walls. Over the last 20 years a substantial number of cold-formed steel framed shear walls have been tested under monotonic and cyclic conditions. These tests provide the support for the cold-formed steel framed shear wall provisions provided in the North American Standard for Cold-Formed Steel Structural Framing (AISI S240-15), the North American Standard for Seismic Design of Cold-Formed Steel Structural …

Seismic Behavior Of Cold-Formed Steel Shear Walls During Full-Scale Building Shake Table Tests, X. Wang, Tara C. Hutchinson, G. Hegemier, Colin A. Rogers

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel sheathed shear walls are now emerging as a strategic vertical lateral load resisting component in seismic design. However, although a number of component cyclic test programs have been conducted in recent years to characterize their hysteretic behavior and guide design, system-level test programs to investigate their performance are so far lacking in the literature. To this end, a unique full-scale CFS-framed mid-rise building shake table test program was conducted to contribute to understanding the behavior of mid-rise cold-formed steel (CFS) wall-braced buildings under a multi-hazard scenario. The centerpiece of this project involved earthquake and live fire testing of …

Wei-Wen Yu International Specialty Conference On Cold-Formed Steel Structures 2018: Recent Research And Developments In Cold-Formed Steel Design And Construction, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

No abstract provided.

Localised Screw Connection Failures In Cold-Formed Steel Roofing Systems, Mayooran Sivapathasundaram, Mahen Mahendran

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Lightweight roofing systems made of thin and high strength steel roof sheeting and battens are commonly used in low-rise buildings. However, they often fail frequently at their screw fastener connections during wind storms due to inadequate connection capacities. Two localised failures, known as pull-through and pull-out failures at the screw fastener connections, have been the root cause for extensive loss of roofing systems under high wind uplift loads. Such premature connection failures often cause partial or even complete loss of steel roofing systems and severe damage to building contents. Therefore many experimental studies have been conducted to investigate the pull-through …

Low Fatigue Response Of Crest-Fixed Cold-Formed Steel Drape Curved Roof Claddings, Krishanu Roy, James B. P. Lim, Amir Mohammad Yousefi, G. Charles Clifton, Mahen Mahendran

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel roof claddings are subjected to significant suction/uplift pressures during high wind events. In New Zealand, the strong prevailing winds makes this a common occurrence. Suction pressures are generated by the turbulence of the wind flow around the building which can vary both spatially and temporally. The weakest link in the roofing system is the connection between roof sheeting and screw fasteners, which if fails, can lead to progressive collapse of the whole roofing assembly. Fluctuating high wind suction pressures can result in either static or fatigue pull-through failure of the roof sheeting at its screw fastener connections. Current …

Stressed Skin Design Of Steel Sheeting Panels – Part 1: Shear Resistance And Flexibility Of Screw Lapped Joists, A. M. Wrzesien, James B. P. Lim, I. A. Macleod, R. M. Lawson

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The shear resistance and flexibility of a steel roof diaphragm depend largely on shear resistance and slip flexibility of the single screw lap joint. In this paper, screw connections relevant to modern roof construction are investigated. The tests provided experimental values of shear/tearing resistance and joint flexibility of seam connections, cladding/purlin connections and purlin/rafter connections. The novel aspects of the experimental research include investigation of the behaviour of shear connections in 0.5mm thick sheeting and thick-to-thin connections in S550 high tensile steel. Overall, six series of tests were conducted and each test was repeated five times in order to demonstrate …

Stressed Skin Design Of Steel Sheeting Panels – Part 2: Shear Panels With Sheeting Fixed On All 4 Sides, A. M. Wrzesien, James B. P. Lim, I. A. Macleod, R. M. Lawson

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

In this paper, the strength and stiffness of different roof panels were investigated, in order to establish their ability to act as in-plane diaphragms for stressed skin design of cold-formed steel portal frames. A total of 6 roof panels, approximately 3 x 3m, were examined by testing with sheeting profiles fixed on 4 sides. A variety of sheeting profiles in two industry standard thicknesses of 0.5 and 0.7mm were tested, all using top-hat shaped purlins fixed with self-drilling, self-tapping screws. The experimental strength and stiffness of each panel were then compared against existing design methods. The Finite Element Analysis (FEA) …

Computational Modeling Of Joist-To-Ledger Connections In Cold-Formed Steel Diaphragms, Hernan Castaneda, M. Eng, Kara D. Peterson

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel framed buildings can involve a range of options for framing systems, including balloon framing, platform framing, and ledger framing. Transfer of lateral forces from the diaphragms to the wall system (and ultimately to the ground) depends on the interactions within the wall-diaphragm connection, which is dependent on choice of framing system. In ledger framing, floor joists are hung from top of wall studs via a rim track (ledger) and clip angle connection. Recent experimental efforts at Johns Hopkins University studied the wall-diaphragm connection with the goal of quantifying its contribution to overall diaphragm response. Results from these experiments …

Effect Of Connection Details On The Cyclic Behavior Of Nestable Screw Sidelaps, S. Torabian, H. Folk, Benjamin W. Schafer

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The connection strength and stiffness sensitivity of screwed sidelaps in nestable steel decks to screw installation details has been experimentally explored via cyclic testing. The cyclic behavior of sidelaps has been recently incorporated in the high fidelity modeling and seismic evaluation of the steel deck diaphragm in rigid wall - flexible diaphragm buildings, where “unzipping” a sidelap (loss of a significant number of sidelap connections along a deck edge) could significantly reduce the seismic performance of the whole diaphragm. A total of 24 monotonic and cyclic sidelap tests have been performed in the Thin-Walled Structures Laboratory at Johns Hopkins University. …

Fire Resistance Of Cavity Insulated Light Gauge Steel Framed Walls, Anthony Deloge Ariyanayagam, Mahen Mahendran

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Light-gauge steel framed (LSF) wall systems are made of cold-formed steel studs and tracks and lined with gypsum plasterboards. They are mostly cavity insulated to provide acoustic and thermal performance. Cavity insulation delays the temperature rise across the wall as it restrains the heat transfer. This delays the ambient plasterboard surface temperature rise and thus improves the insulation failure time of LSF walls. However, LSF walls are also used as load bearing walls. Having cavity insulation causes the fire side temperatures to increase rapidly, resulting in a higher temperature gradient across the stud depth. This leads to higher thermal bowing …