Digital Commons Network^™

Minimizing The Negative Effect Of Pumping On Scc Freeze-Thaw Durability, Daniel Galvez-Moreno

Doctoral Dissertations

“The durability of concrete must be ensured to reduce the carbon footprint of the production of portland cement. If concrete is properly designed to preserve its integrity under adverse exposure conditions, the service life of the material can be extended with minimum maintenance. Nevertheless, bad handling, placing, finishing or curing practices can abate the durability potential and service life of even the best mix design. Pumping concrete is a very efficient placing technique that offers significant cost reduction and versatility at the jobsite, but it also has the potential of altering the air void system parameters, which are key to …

Complexities Observed During The Development Of A Rheological Testing Procedure For Small Cement Paste Samples, Aida Margarita Ley-Hernandez

Doctoral Dissertations

“Rheology has been widely used to describe the flow properties of fresh cement-based suspensions. The use of a rheometer to characterize these properties is not a straightforward task due to the dependency to different preparation conditions, mixing processes, testing procedures and measuring instruments employed. In addition, shear and time dependency of the material which undergoes chemical and physical particle bonding, caused by hydration of cement and flocculation. Nevertheless, the characterization and understanding of the rheological behavior of cement-based materials have become essential with the recent introduction of novel applications like digital construction in the field of civil engineering, among others. …

Structured Catalysts Designed And Manufactured By 3d-Printing Technique For Functional Integration Of Catalytic Systems, Fatima Magzoub

Doctoral Dissertations

"Microporous zeolites are widely used as heterogeneous catalysts in a wide variety of chemical and petrochemical industries to produce value-added chemicals and fuels, owing to their large surface area, acid-base properties, high thermal stability, and excellent shape-selectivity.

The overall goal of this research was to shape engineer composite zeolites and fine-tune their physiochemical properties to improve the catalytic production of dimethyl ether (DME) and light olefins that are typically used as substitution to diesel fuel and polymer precursors, respectively. Specifically, HZSM-5 and silicalite-1 zeolites were formulated into monolithic contactors using 3D printing technique, followed by subsequent SAPO-34 crystals growth through …

Enhanced Electrochemical Performance Of Li-Ion Battery Cathodes By Atomic Layer Deposition, Yan Gao

Doctoral Dissertations

”Li-ion battery now plays an irreplaceable role in supplying green and convenient energy. In this work, atomic layer deposition (ALD) was used to modify Li-ion battery cathode particles for performance enhancement.

An ultrathin and conductive CeO₂ ALD film was deposited on Li-rich layered cathode particles, of which the specific capacity and cyclic stability were significantly improved. On the same cathode particles, FeO_x ALD and post-annealing resulted in a stable and conductive surface spinel phase to improve the performance.

Synergetic TiN coating and Ti doping were performed on a LiFePO₄ (LFP) cathode and extended its cycle life. The …

Additive Manufacturing Of Customized Lithium-Ion Batteries: Process Fundamentals And Applications, Xiaowei Yu

Doctoral Dissertations

“In the pasting decades, considerable efforts have been spent in developing the next-generation lithium-ion batteries (LIBs), from advanced active materials to new manufacturing methods. The development of additive manufacturing (AM) has brought new opportunities to LIBs. In this work, two AM methods are introduced for fabricating electrodes of LIBs. The first method is aerosol printing, which is a solvent-based wet additive method. Whereas the second method is a solvent-free, dry printing method. The commonly used materials for current collectors and active materials (including cathodes and anodes) of LIBs are aerosol printed and the electrochemical functionalities of the printed materials are …

Investigation Of Urea Decomposition And Deposit Formation In Diesel Exhaust After-Treatment System, Anand Alembath

Doctoral Dissertations

“Urea-selective catalytic reduction (SCR) system has proved to be an effective solution to reduce NO_x emissions in commercial vehicle (CV) diesel engines. A significant challenge in urea injection is to comprehend its decomposition chemistry that leads to formation of undesired deposits in the exhaust system unit. Due to complex interaction of multi-phase fluid flow and transport processes, significant uncertainty is associated with the identification of interacting factors that control the deposit initiation and its growth. To meet the future ultra-low NO_x emissions and to deliver ammonia without deposit formation, there is an imminent need to develop the urea-SCR …

Fabrication And Characterization Of Multifunctional Composites, Aditya R. Thakur

Doctoral Dissertations

“This study details the research to facilitate fabrication and characterization of novel structural composites reinforced with carbon fibers. Across industries, materials with high performance-to-weight ratio are sought after. Using carbon fibers as secondary phases in these proposed composites, specific characteristics can be tailored in these materials to manufacture strong, lightweight, high performance structures. The first part of the research focused on the improvement in the mechanical properties of the composites using carbon fiber reinforcement. As a part of this study, toughened ceramic composites with predictable failure patterns were produced using carbon fiber inclusions. A closed-form analytical model was developed to …

Design And Fabrication Of Field-Effect Iii-V Schottky Junction Solar Cells, Amirhossein Ghods

Doctoral Dissertations

“A new concept of field-effect photovoltaic devices with a focus on design and fabrication of single and multi-junction solar cells using III-V materials has been shown and proved. Schottky solar cells based on metal-(insulator)-semiconductor (M-I-S) structure have been designed and fabricated using various wide bandgap semiconductors, such as GaAs and Al_0.3Ga_0.7As. A secondary bias layer has been introduced to the device structure, in which it creates additional band bending and subsequently depletion region at the flat band regions on the top surface of the device. It should be mentioned that the bias layer is designed to …

Attention Mechanism In Deep Neural Networks For Computer Vision Tasks, Haohan Li

Doctoral Dissertations

“Attention mechanism, which is one of the most important algorithms in the deep Learning community, was initially designed in the natural language processing for enhancing the feature representation of key sentence fragments over the context. In recent years, the attention mechanism has been widely adopted in solving computer vision tasks by guiding deep neural networks (DNNs) to focus on specific image features for better understanding the semantic information of the image. However, the attention mechanism is not only capable of helping DNNs understand semantics, but also useful for the feature fusion, visual cue discovering, and temporal information selection, which are …

Investigation Of Wide Bandgap Semiconductors For Room Temperature Spintronic, And Photovoltaic Applications, Vishal Saravade

Doctoral Dissertations

"Suitability of wide bandgap semiconductors for room temperature (RT) spintronic, and photovoltaic applications is investigated.

Spin properties of metal-organic chemical vapor deposition (MOCVD) – grown gadolinium-doped gallium nitride (GaGdN) are studied and underlying mechanism is identified. GaGdN exhibits Anomalous Hall Effect at room temperature if it contains oxygen or carbon atoms but shows Ordinary Hall Effect in their absence. The mechanism for spin and ferromagnetism in GaGdN is a combination of intrinsic, metallic conduction, and carrier-hopping mechanisms, and is activated by oxygen or carbon centers at interstitial or similar sites. A carrier-related mechanism in MOCVD-grown GaGdN at room temperature makes …

Geophysical Assessment Of The Lake Chesterfield Site, Missouri, Diya Ali Ahmad Alfuqara

Doctoral Dissertations

"Since construction of the Lake Chesterfield, Missouri in 1986, significant leaks have occurred causing the lake to lose substantive volumes of water. Mitigation efforts, have not solved the problem. Indeed, in June of 2017, the water level in Lake Chesterfield dropped at an alarmingly rapid rate. Prior to authorizing additional mitigation work, the Lake Chesterfield. Home Owners Association (LCHOA) decided to acquire geophysical data across the drained and dry lake bed. These information would help a geotechnical engineering firm determine the most appropriate mitigation plan.

In the summer of 2018, electrical resistivity tomography, multichannel analysis of surface wave, and spontaneous-potential …

Imaging In Karst Terrain Using The Electrical Resistivity Tomography (Ert) And Multi-Channel Analysis Of Surface Waves (Masw) Methods, Hassan Abdullah Alzahrani

Doctoral Dissertations

"Electrical Resistivity Tomography (ERT) and Multi-channel Analysis of Surface Waves (MASW) methods were used to image the subsurface in karst terrain in the southeast of Missouri. A SuperSting R8 system was used to acquire the ERT profiles; a multi-channel engineering seismograph was used to acquire the MASW data. The latter data were used to constrain and verify the ERT interpreted depth to top-of-rock and soil thickness. The ERT data were used to delineate the soil/rock interface and to identify zones of anomalously high moisture content within the bedrock.

The primary objective of the research was to determine the cause of …

Physical And Biological Factors Affecting Oxygen Transfer In The Activated Sludge Wastewater Treatment Process, Kenneth A. Campbell

Doctoral Dissertations

“The activated sludge (AS) process is widely utilized for wastewater treatment due to its versatility and general resiliency, but is energy intensive, requiring aeration and mixing energy inputs to maintain the biochemical reaction and optimize treatment performance. This study is focused on determining different factors that influence oxygen transfer and consequently its energy demand.

AS morphology, as described by the d₁₀, d₂₀, d₃₂, specific filament length (SFL), 30 min settleability (SV₃₀), etc., does influence the OTE. Filamentous organisms increase the hydrodynamic radius of suspended particles, which dilates mixed liquor apparent viscosity (µ …

Observer-Based Event-Triggered And Set-Theoretic Neuro-Adaptive Controls For Constrained Uncertain Systems, Abdul Ghafoor

Doctoral Dissertations

"In this study, several new observer-based event-triggered and set-theoretic control schemes are presented to advance the state of the art in neuro-adaptive controls. In the first part, six new event-triggered neuro-adaptive control (ETNAC) schemes are presented for uncertain linear systems. These comprehensive designs offer flexibility to choose a design depending upon system performance requirements. Stability proofs for each scheme are presented and their performance is analyzed using benchmark examples. In the second part, the scope of the ETNAC is extended to uncertain nonlinear systems. It is applied to a case of precision formation flight of the microsatellites at the Sun-Earth/Moon …

Evaluation Of The Performance Of Different Polymer Gel Systems As An In-Depth Gel Treatment Using Numerical Simulation, Tariq K. Khamees

Doctoral Dissertations

"Oil production from heterogeneous and naturally fractured reservoirs are usually hindered due to the presence of high-permeability streaks and natural fractures networks. Oil production could be more lowered if there is a crossflow from the high- to the low-permeability layers and high mobility ratio. These problems are called conformance problems and the treatment is called conformance improvement technologies (CITs). The aims of CIT is to correct the heterogeneity of the reservoir and to lower the unfavorable mobility ratio. These technologies are leading to the diversion of post-treatment water into the low-permeability layers and to increase the viscosity of the displacing …

Novel Approaches For Reliable And Efficient Circuit Design, Prashanthi Metku

Doctoral Dissertations

"In this research work, a suite of approaches are presented to improve reliability of 3D heterogeneous processors (3DHP) and to reduce the area overhead of asynchronous designs. This work is primarily divided into two parts. In the first part, we present an approach for improving reliability in 3DHP. Typically, in 3DHP, thermal hotspots introduce spatial and temporal variability that results in wide bit error variation in DRAM dies. To address this issue multi- path BCH decoder is introduced. Based on the thermal gradient data generated by on-chip temperature sensors, the proposed methodology specializes in adaptively estimating the number of errors …

Strengthening Qc Relaxations Of Optimal Power Flow Problems By Exploiting Various Coordinate Changes, Mohammad Rasoul Narimani

Doctoral Dissertations

"Motivated by the potential for improvements in electric power system economics, this dissertation studies the AC optimal power flow (AC OPF) problem. An AC OPF problem optimizes a specified objective function subject to constraints imposed by both the non-linear power flow equations and engineering limits. The difficulty of an AC OPF problem is strongly connected to its feasible space's characteristics. This dissertation first investigates causes of nonconvexities in AC OPF problems. Understanding typical causes of nonconvexities is helpful for improving AC OPF solution methodologies.

This dissertation next focuses on solution methods for AC OPF problems that are based on convex …

Experimental And Modeling Studies Using Packed Bed Reactors: Liquid Phase Ethylene Production By Hydrogenation Of Acetylene, Humayun Shariff

Doctoral Dissertations

"Gas-phase catalytic hydrogenation of acetylene to produce ethylene, commonly practiced in industries, has green oil formation, which leads to catalyst deactivation and sometimes reactor runaway risks due to high exothermicity. To overcome these issues as well as to increase the selectivity and conversion, liquid-phase hydrogenation of acetylene was investigated in packed bed reactors (PBR) using a commercial catalyst. The reactor performance of two-phase flow PBRs was assessed experimentally complemented by a validated mathematical model at different scales.

The selective hydrogenation of acetylene in the liquid phase over a commercial 0.5 wt% Pd/Al₂O₃ catalyst was investigated in a …

Minimizing The Detrimental Effects Of Hydro-Peaking On Riverbank Instability: The Lower Osage River Case, Wesam Sameer Mohammed-Ali

Doctoral Dissertations

"The fluctuation of water level downstream from dams due to hydropower flow releases negatively affects the riverbank stability. Therefore, this research aims to examine the feasibility of using an optimization technique to mitigate the riverbank instability resulting from the outflow variation of hydropower plants. The effects of the water releases from the Bagnell Dam were investigated by computing a series of safety factors for 78 cross sections along the 81-mile stretch of the lower Osage River in relation to outflow events by using the integrated BSTEM model incorporated into the HEC-RAS model. The 1-D sediment transport and unsteady flow in …

Stabilization Dynamics Of The Ozone Molecular System, Sangeeta Sur

Doctoral Dissertations

"The observation of larger-than-expected concentrations of heavier isotopologues of ozone known as 'ozone isotopic anomaly' in the stratosphere is a mass-independent effect (in contrast to most kinetic isotope effects familiar to chemists) that is traced back to the recombination process in the formation of ozone in the Chapman cycle. Understanding the relative efficiencies (often approximated as equal for different isotopologues) of the stabilization step (some of the details of which are still a mystery) which involves energy transfer from a highly excited ozone molecule to a third body, M (argon atom in this case) to form stable ozone is a …

Design Of X-Ray Source For Real-Time Computed Tomography, Wesley William Tucker

Doctoral Dissertations

"The reduction of motion blur in computed tomography (CT) drives the current research for multisource CT. Due to their compact nature, the current multisource systems utilize stationary angled anodes. Unfortunately, these configurations neither simplify the imaging geometry, nor satisfy the need for managing the high thermal loads demanded by real-time CT (30 acquisition frames per second). To add to the current field of knowledge, two x-ray tube concepts are presented in this dissertation. First, a simulation of transient thermal analysis was performed on a compact transmission-type x-ray tube anode operating in pulse-mode. A correlation was found between deposited beam power …

Characterization And Recyclability Of 304l Stainless Steel Powder For Use In The Selective Laser Melting Process, Austin Taylor Sutton

Doctoral Dissertations

"Powder-bed fusion refers to a subset of additive manufacturing (AM) methods which successively melts and solidifies selected regions within a powder bed on a layer-by-layer basis to construct components directly from computer-aided design files. Laser Powder-Bed Fusion (L-PBF) is a process among the powder-bed fusion techniques that utilizes a laser to consolidate particles into a material with little porosity. During the L-PBF process, the large energy input from the laser causes the production of ejecta in the form of laser spatter and condensate, both of which have the potential to settle in the surrounding powder bed compromising its reusability. In …

A Broad Iceland Plume Associated With Two Phase Transitions At The 660 Km Discontinuity: Constraints From Receiver Functions, Dan Wang

Doctoral Dissertations

"In spite of the fact that Iceland is frequently regarded as the archetypal example of mantle plumes, the existence, depth extent, origin, dimension and excess temperature of the hypothesized plume remain enigmatic and hotly debated. The controversy mostly originates from the limited vertical resolution of seismic tomography techniques and the associated uncertainty in the depth and lateral extents of the lower wavespeed anomaly. Here we utilize a robust receiver-function-based technique to image the topography of the 410 and 660 km discontinuities bordering the mantle transition zone beneath Iceland and surrounding oceanic regions, and construct thermal and seismic wavespeed models of …

Seismological Investigations Of Lithospheric Structure Beneath The East African Rift System And The Kalahari Craton, Tuo Wang

Doctoral Dissertations

"In spite of numerous geophysical studies have been conducted in East African Rift System and Southern Africa, the structure and evolution of the crust and upper mantle are still controversial. In this study, we applied multiple seismological techniques to investigate the structure in the crust and uppermost mantle beneath the East African Rift System and Kalahari Craton in southern Africa. First, the technique of ambient noise tomography was applied to image shear wave velocity model from surface to the depth of 40 km beneath the Malawi and Luangwa rift zones. For the first time, a high-resolution 3-D shear wave velocity …

System Si/Pi Modeling And Analysis, Biyao Zhao

Doctoral Dissertations

"A physics-based circuit modeling methodology for 3D IC/packages is proposed here. The method is based on partial element equivalent circuit (PEEC) and layered Green's function (LGF). The LGFs are calculated from discrete complex image method (DCIM) with three terms, direct coupling, complex images, and surface wave, extracted to analyze the wave behavior. The dominate terms for LGFs are analyzed for four stack-ups in 3D IC/packages. Analytical formulas that include the contribution of complex images are proposed for partial capacitance calculation, with the complex image extracted from LGFs. A chip PDN geometry is used to illustrate the use of LGF in …

Trajectory Control Of A Wheeled Robot Using Interaction Forces For Intuitive Overground Human-Robot Interaction, George Leno Holmes Jr.

Doctoral Dissertations

"Effective and intuitive physical human robot interaction (pHRI) requires an understanding of how humans communicate movement intentions with one another. It has been suggested that humans can guide another human by hand through complex tasks using force information only. However, no clear and applicable paradigm has been set forth to understand these relationships. While the human partner can readily understand and adhere to this expectation, it would be difficult for anyone to explain their intuitive motions with strict rules, algorithms, or steps. Uncovering such a procedural framework for the control of robotic systems to execute expected performance simply from force …

Modeling A Nuclear Research Reactor And Radiation Dose Estimation In An Accident Scenario, Abdulaleem Abdulmajeed Bugis

Doctoral Dissertations

“A detailed, flexible three-dimensional (3D) model of the Missouri S&T Reactor (MSTR) with a heterogeneous core geometry was developed using the Standardized Computer Analyses for Licensing Evaluation (SCALE). A Graphical User Interface (GUI) was developed for SCALE, which allows the user to generate an input file automatically. The SCALE model was validated with a Monte Carlo N-Particle Transport (MCNP) model of the MSTR. The validation process was based on the criticality calculations using the Criticality Safety Analysis Sequence (CSAS6). Three geometrical models were examined. The SCALE model that has the full detailed geometry showed a good agreement with the MCNP …

Development Of Radiation Transport Techniques For Modelling A High-Resolution Multi-Energy Photon Emission Tomography System, Seth Kilby

Doctoral Dissertations

”Nondestructive characterization techniques such as gamma tomography represent powerful tools for the analysis and quantification of physical defects and radionuclide concentrations within nuclear fuel forms. Gamma emission tomography, in particular, has the ability to utilize the inherent radiation within spent nuclear fuel to provide users with information about the migration and concentration of fission and activation products within the fuel form. Idaho National Laboratory is interested in using this technology to analyze new nuclear fuel forms for potential use in next generation nuclear reactors. In this work, two aspect of the system are analyzed. The first is a semi-analytic radiation …

Development Of Tools For Water Management In The Hatra Watershed (Northwestern Iraq) Using Satellite Technologies, Majid S. Mohamod

Doctoral Dissertations

“All around the world the demand for water is increasing, especially in arid and semi-arid regions, including Iraq which subject to continuous desertification that is worsening, more importantly the Jezira region in northwestern Iraq. Thus, it’s crucial to have a better strategy for water management. One of these strategies is to promote groundwater recharge for restoring the aquifer depletion. The successful groundwater recharge is limited by some potential data such as the annual water budge and precipitation measurements. The atomospheric and hydrological observations are limited by sparse population which tends to be less in arid and semi-arid regions. Therefore, an …

Integrating Resilience Into Military Infrastructure Mission Assurance Assessments And Decision Making, John Richards

Doctoral Dissertations

“This research created the Mission Assurance Resilience Matrix, a decision framework that integrates existing infrastructure assessment methods with emerging resilience research to model resilience under uncertainty as part of a detailed infrastructure management system. This framework enables military decision makers to easily visualize deficiencies in infrastructure resilience and assess where to most efficiently allocate resources. This research further extends results by including modules on training and education as a component of the scope of work.

There are three significant contributions of this research. The first identifies the gaps of how and where modeling under uncertainty, infrastructure systems management, and resilient …