Digital Commons Network^™

A Model Study Of The Behavior Of Elastic Liners In Shallow Underground Openings, Martin Samuel Oudenhoven

Masters Theses

"Models of epoxy resin were used in a stress freezing technique to determine areas of possible failure in lined circular openings. These models were loaded in a centrifuge for a fixed period of time, after which they were analyzed photoelastically. The material characteristic changes, with time, were recorded on graphs and used in the analysis.

Two types of tests were conducted; one, where the lining thickness was changed and, the other, where materials of the liner and plate material were changed.

The resulting analyses furnished proof that the greater the rigidity of the lining, the higher the stress developed in …

A Comparison Of A-C And D-C Lead Compensation From D-C Prototype Networks, Piyush Parikh

Masters Theses

"The object of this thesis is to study the difference in transient and frequency response characteristics between a prototype d-c phase lead compensating network and an equivalent a-c phase lead compensating network.

A second order servo is selected to be compensated and five d-c prototype and equivalent a-c phase lead compensating networks are designed. The frequency characteristics of the a-c networks are obtained experimentally and these of the d-c networks are obtained analytically. The characteristics of both networks are compared and their differences are studied. The transient characteristics of the d-c and a-c compensated closed-loop systems to a step input …

A Model Study Of The Induction Log Applied To The Detection Of Asymmetrically Located Orebodies, Robert Walter Piekarz

Masters Theses

"This research project was undertaken to determine the possibility of using an induction log of the type applied in petroleum exploration, for the detection of conductive ore- bodies asymmetrically located with respect to a borehole. Since a mathematical analysis would be extremely complex, a model study was conducted, using graphite bodies of various shapes to simulate different modes of mineral occurence.

The investigation showed that these bodies were readily detectable, and were capable of yielding anomalous curves characteristic of their geometry. The values of apparent conductivity decreased rapidly with lateral displacement, from the logging tool, as expected, due to the …

A Correlation Of Heat Transfer Coefficients Using An Induction Heater, Charles Maurice Martin

Masters Theses

"This thesis represents a study of the following problems. (1) Determination of techniques and equipment which would give satisfactory correlation of experimental heat transfer coefficients with those obtained from acceptable heat transfer equations when using an induction heater as the heat source. (2) Determination of depth of energy deposition in a thick-walled tube due to induction heating.

Techniques were developed that gave a correlation between experimental and calculated coefficients that were within -5% for minimum flow and +8% for maximum flow.

Because of difficulties in positioning thermocouples, the depth of energy deposition could not be accurately determined. However, two surface …

A Comparison Of The Load Carrying Characteristics Of Hydrostatic Thrust Bearing Using Monatomic, Diatomic, And Triatomic Gases, Joseph C. Pigott

Masters Theses

"The purpose of this investigation is to compare the load carrying characteristics of gases with different ratios of specific heat. The design, construction, and operation of an apparatus for testing and comparing the load carrying characteristics of gases are described. Several monatomic, diatomic, and triatomic gases were tested and the results evaluated and compared. The data are tabulated and displayed in a series of curves.

It was found that the monatomic gases exhibit a greater clearance for a given load and a greater total load carrying capacity than the diatomic gases which in turn have a greater clearance and total …

A Comparison Of Backwater Profile Computation, Alwin Chang Hsin Young

Masters Theses

"Bakhmeteff's, Von Seggern's, and the Standard Step methods were chosen for a comparative study of backwater profile determinations made with the assistance of a digital computer. This study concentrated on the M-l type of curves for different kind of prismatic channels; i.e. rectangular, trapezoidal, and parabolic channels. From the results obtained by each method for different channels, the consistency between the several methods and their applicability to all shapes of channel had been studied. Also the effect of the number of reaches used in flow profile determinations, the effect of the use of an average value of (1-ß), hydraulic exponents …

An Investigation Of The Deformation Textures Of Cobalt, Roy Carl Wilcox

Doctoral Dissertations

"Deformation textures of various cobalt structures as a result of cold rolling together with some annealing textures were studied. The textures of cobalt were determined using a modification of the Schulz-Decker Geiger counter technique. Pole figures of the (1011), (0001) and (1010) planes were constructed. Also, a study of the microhardness of cobalt was made.

Microhardness tests were performed on various cobalt structures, in both the cold rolled and unworked conditions. The microhardness was found to vary with the source of the cobalt, the crystal orientation, and the amount of deformation and twinning. Deformation lines about the hardness impressions diffused …

A Study Of Duffing's Equation, Charles Kirby Murch

Masters Theses

"The unforced cases of Duffing's equation and the equation of the simple pendulum are considered by imposing certain conditions on a linear partial differential equation. Geometrical arguments are presented which lead to solutions of the special cases considered.

Undetermined functions of integration in the solutions limit their use to the approximation of systems with small non-linearity"--Abstract, page ii.

Detection Of Rust Formed Under Paint Films, James Larry Inglis

Masters Theses

"Corrosion is an evil that has plagued man since before the iron age. Three ways of controlling corrosion are: 1. alloy the metal to make it chemically inert to corrosion, .2. change the surroundings to a noncorrosive atmosphere, and 3. isolate the metal from the corrosive atmosphere, as for instance by the application of a number of coats of paint that has been found to be the most economical method.

At present, there is no reliable method of testing the effectiveness of a paint film that does not require the corrosion products to destroy the paint film and show themselves …

Development Of A Simple Bar Method Thermal Conductivity Test, V. J. Flanigan

Masters Theses

"A linear flow bar method type apparatus was set up for finding thermal conductivities by comparison techniques. Comparison technique consist of using a standard specimen where the thermal conductivity is known and comparing it to the unknown specimens to find their conductivity. Apparatus of this type usually uses thermocouples for the required temperature measurements, but thermistors were used in this experiment. The thermistors used required calibration to measure accurate temperatures and this was accomplished by using the known temperatures of the changes of state of some common materials. Five alloys were used to evaluate the method: SAE 1020 steel, gray …

The Effect Of The Rolling Load On The Micro-Structure Of Low Carbon Sheet Steel, Jerry Lee Cadden

Masters Theses

"A Stanat 315, two high-four high, combination rolling mill is used to cold roll annealed, low carbon steel strips. A method of measuring the rolling load was presented. The method consisted of constructing a load cell using SR-4 strain gages attached to a steel column. The load cell was placed under the hold down screw of the rolling mill and a known load was applied. The stresses from this load were transferred to the mill housing where another SR-4 strain gage was located. The strain in the mill housing was recorded at the corresponding applied load. During rolling, the strain …

A Weight Loss Technique For The Determination Of Phase Boundaries, Robert Lee Benner

Masters Theses

"An apparatus has been designed and constructed that would continuously record the weight loss of a sample in a flowing inert atmosphere, at a constant temperature.

A technique has been developed to determine the phase boundaries of a binary phase diagram.

Alloys of the magnesium-nickel, cadmium-antimony, copper-cadmium, copper-zinc, and magnesium-zirconium systems were subjected to investigation to verify the operation and resolve a number of limitations of the equipment.

These investigations disclosed that the apparatus gave the best results with alloys having vapor pressures in the range between 1 and 35 millimeters of mercury"--Abstract, page 2.

Transpiration Cooling Of A Porous Plate, Stephan A. Sayegh

Masters Theses

"Transpiration cooling has long been known as an effective way of removing heat from porous materials. This thesis is a new approach to one of the problems of transpiration cooling in the steady state.

The specific problem considered here is that of a uniform porous plate through which a liquid is forced. This liquid vaporizes at a short distance from the surface through which it is forced and leaves the porous plate at the other surface which is exposed to hot gases. It also protects the hot surface by forming an insulating layer between that surface and the hot gases. …

Analysis Of Flat Plates By Reaction Distribution Method, David D. W. Yang

Masters Theses

"This study was made to analyze rectangular flat plates by the method of Reaction Distribution and to compare results obtained by this method with that of other methods. The basic approach is to divide the plate into an equivalent grid system and introduce temporary supports at the intersecting joints. The results from this study shows that the Reaction Distribution method is useful in a qualitative analysis of the behavior in a plate but is less satisfactory in obtaining reliable quantitative results"--Abstract, page 2.

A Study Of The Permeability And Separation Of Carbon Dioxide And Hydrogen By Gaseous Diffusion Employing Barriers Of Polystyrene, Carl J. Wallace

Masters Theses

"The purpose of this investigation was to study the permeability and separation of carbon dioxide and hydrogen by gaseous diffusion employing barriers of polystyrene. The offset of temperature and barrier thickness on the permeability and separation of carbon dioxide and hydrogen wore Investigated for barriers of one, three, and five-mil thicknesses and for temperatures of 26, 35, 45, and 50 degrees centigrade.

With an increase in barrier thickness of one to five- mils, the permeability of carbon dioxide decreased to one-fourth of its value at the one-mil thickness. The hydrogen permeability decreased to approximately two- thirds of its value at …

A Study Of Composite Beams Made To Find An Approximate Relationship Between The Top And Bottom Flange Steel Ratio, Murli U. Hasrajani

Masters Theses

"At present in building construction the use of the composite beams is not very common. The use of the concrete beams is seen in almost all construction. By using composite beams in building construction more durability and savings in cost could be achieved. This paper shows an approximate design procedure which could be followed without running a number of trials with different sections to arrive at the required one. The ratio of top flange steel to the bottom flange steel can be determined if one knows the loads, span and the depth of the beam required"--Abstract, page i.

Neutron Flux Mapping Of The Msm Reactor, Cary Chow-Yuen Chen

Masters Theses

"This investigation presents a mean to determine thermal neutron flux of a reactor by irradiating copper wires inside the fuel elements. The activity recorded after decay correction, is the relative thermal neutron density. Thermal neutron flux is a measure of the neutron density at thermal energy, 0.025 ev.

Gold foils irradiated at National Bureau of Standards were used as the absolute neutron flux calibration standards. The average flux of the reactor with water as the reflector ranges from 7.24 x 10¹⁰ neutrons/cm² - sec. to 7.87 x 10¹⁰ neutrons/cm² - sec. as obtained from the calculations. …

Experimental Stress Analysis Of Bolts In A Flange Coupling, Vijay Rastogi

Masters Theses

"In this investigation an attempt has been made to determine simple formulae leading to a better, more useful and much safer design of flange coupling bolts. The bolts were tested under tensile loading and bending and hence the results obtained apply for bolts under these modes of loading only.

The behavior of flange bolts under different initial tightening torques was studied by measuring strains in a bolt on which strain gages had been attached* . From this, the load producing separation of flanges, under different tightening torques, was determined and used in deriving formulae for prediction of the load for …

A Study Of Placer Tin Materials From Southern Thailand, Somkiat Ganthavee

Masters Theses

"This thesis deals with a series of investigations of placer tin samples from a Chinteik's Tin-dredge, Gnaw District, Ranong Province, and the Tin-Pet mine, Phang-gna Province, in southern Thailand.

A brief summary of the geography and geology of Thailand as a whole has been given as a general introduction to the source of the materials studied in this thesis.

The results of sieve analyses have shown that the sluice boxes do not effectively concentrate the cassiterite grain below 0.147 mm. from the rough concentrate treated in the tin-dressing shed.

It has been found that roundness and shape determinations of quartz …

A Study Of The Dissolution Of Zr-O Alloys In Hydrofluoric Acid, Wayne Gilbert Custead

Doctoral Dissertations

"The purpose of this investigation was to ascertain and explain, if possible, the effect of oxygen in the metal on the kinetics and electrochemistry of the reaction of zirconium in hydrofluoric acid solutions. This entailed the determination of the effect of oxygen on the dissolution rates, activation energies, dissolution potentials, and difference effect for zirconium in hydrofluoric acid and hydrofluoric-hydrochloric acid mixtures.

The alpha-phase solid solutions of oxygen and zirconium were synthesized by the powder-metallurgy technique. Both the alloy analysis and dissolution rates were obtained by the gas evolution method according to the reaction:

ZrO_x + 4HF → ZrF …

Lattice Parameters, Densities And Imperfections In Indium And Indium-Cadmium Alloys Rich In Indium, Paluri Bhimeswara Rao

Doctoral Dissertations

"An investigation of perfection of the structure of the indium-cadmium system was suggested by the interesting properties of indium and its cadmium alloys. The lattice of indium, though tetragonal, may be considered as distorted cubic, its axial ratio being 1.0767 at 20°C. Furthermore earlier studies have revealed a transformation of the tetragonal structure to cubic in the presence of cadmium.

To determine the perfection or soundness of the indium and indium-cadmium alloys rich in indium, pure indium (99.999 per cent purity) and eight samples of the indium-cadmium alloys ranging in composition from 2.977 to 10.015 per cent by weight of …

Statistical Analysis Of Fracture Stresses Of Triaxial Porcelain Bodies, Robert E. Moore

Doctoral Dissertations

"Triaxial porcelain bodies containing various forms of silica, quartz, cristobalite and fused silica, were strength tested in bending. Significance tests were employed to discern real differences in the strength sample statistics caused by the various forms of silica. Firings were performed at three temperature levels. The differences in strength sample statistics were correlated to the microstructures of these silica porcelains.

A triaxial alumina porcelain body was employed as a model brittle solid for a study of the effect of flaw density on mean fracture stress. The flaws were introduced in the form of large diameter (d̄ = 115 microns) rounded …

The Geology Of The Eldorado Mining District, Clark County, Nevada, Spenst M. Hansen

Doctoral Dissertations

The rocks of the Eldorado mining district, Clark County, Nevada, are of Precambrian, Tertiary and Quaternary age. Precambrian rocks include a heterogeneous series of gneisses and schists, younger garnetiferous granite gneiss and a youngest group of pegmatites. Paleozoic and Mesozoic rocks present in surrounding areas are absent in the district and Tertiary volcanics lie directly on the Pre- cambrian basement. Tertiary rocks consist of middle to late Tertiary flows and pyroclastic beds of andesite, basalt and rhyolite. These are assigned to three volcanic formations: the Patsy Mine volcanics; the Golden Door volcanics; and the Mount Davis volcanics. The Patsy Mine …

The Missouri Miner, December 15, 1961

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, December 08, 1961

The Missouri Miner Newspaper

No abstract provided.

Missouri S&T Magazine, December 1961, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

The Missouri Miner, December 01, 1961

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, November 17, 1961

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, November 10, 1961

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, November 03, 1961

The Missouri Miner Newspaper

No abstract provided.