Digital Commons Network^™

Atmospheric Measurements Of Ccn In The Supersaturation Range 0.013-0.681%., Darryl J. Alofs, T. H. Liu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Concentrations of Cloud Condensation Nuclei in the Atmosphere Were Measured at Rolla, Missouri, Near Ground Level. a Total of 432 Spectra Were Measured over a 10-Month Period. No Consistent Seasonal or Diurnal Pattern Was Observed. Possible Implications for Fogs and Stratus Clouds and for Nuclei Chemical Composition Are Discussed.-From Authorscloud Condensation Nuclei Rolla Missouri Fogs

Novel Demonstration Of Total Internal Reflection, Dwight C. Look

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Modern Spectroscopy With A Spectrometer By The Optogalvanic Effect, Kenneth Arnett, Richard A. Anderson, Ralph William Alexander

Physics Faculty Research & Creative Works

An Experiment Involving the Optogalvanic Effect Suitable for the Advanced Physics Laboratory is Described. This Experiment Complements the Usual Basic Experiment in Atomic Spectroscopy Where Spectra Are Recorded on Photographic Film with a Spectrograph or with a Monochromator and Photomultiplier. the Optogalvanic Effect Used the Atoms Being Studied as the Detector and a Tunable Dye Laser as the Source. Linewidths Observed Are Those of the Dye Laser that Are Considerably Smaller Than Those Obtained with the Usual Laboratory Monochromator. the student is Introduced to the Techniques of Spectroscopy with Pulsed Dye Lasers and to a Spectrum for Which LS Coupling …

The Effect Of Plasma-Deposited Polymers On The Nucleate Boiling Behavior Of Copper Heat Transfer Surfaces, T. Hinrichs, E. Hennecke, H. Yasuda

Chemistry Faculty Research & Creative Works

The effect of plasma deposited polymers on the nucleate boiling behavior of copper heat transfer surfaces, using water as the boiling liquid, was determined. The monomers used were tetrafluoroethylene (TFE) and methane. It was found that an 18 nm thick coating of TFE enhanced the nucleate boiling, while a 150 nm thick coating reduced the nucleate boiling. Both 15 nm and 150 nm thick coatings of methane reduced the nucleate boiling, with the effect being more pronounced with the thicker coating. A surface energy effect is postulated to explain the enhanced boiling observed. © 1981.

Transverse Thermal Response Of A Composite Bridge, Michael J. Filla

Masters Theses

"A two-span, composite-design, test structure was subjected to thermal loading. The resultant longitudinal and transverse response was correlated with that calculated by a prior theoretical procedure. The theoretical procedure was reconfirmed for longitudinal stress, and indicated within reasonable probability for transverse stress. No measurable diaphragm influence was observed"--Abstract, page iii.

Structure And Properties Of Neodymium Chromite, David Charles Hitchcock

Masters Theses

"Pure, accepton and Al doped NdCrO₃ were prepared by an organo-metallic process.

The crystal structure and lattice parameters were determined by x-ray diffraction. All compositions were orthorhombic Pbnm.

Pellets were pressed from powders of each composition and sintered to high density in a reducing atmosphere. When a small amount of Fe was substituted for Cr, the powder could be sintered in air.

Electrical conductivity for acceptor doped NdCrO₃ varied from about 1 (ohm cm)^-1 at room temperature to about 10 (ohm cm)^-1 at 900°C, about two orders of magnitude higher than the electrical conductivity of the …

The Design And Development Of A Human Interface For An Intelligent Terminal For A Process Control Industry, V. Rangarajan

Masters Theses

"A complete description of an intelligent Terminal to be used in a Process Control Industry is presented. The system software is discussed. An account of the hardware and software interfaces for the input devices, along with the description of the input devices, is included. The data base used in the system is described with an example. Future enhancements have been proposed."--Abstract, page iii.

Glow Discharge Polymerization., H. Yasuda

Chemistry Faculty Research & Creative Works

In this review-paper the author summarizes some important aspects of ″polymer formation″ in the glow discharge polymerization or plasma polymerization, rather than presenting a bibliographical review of work. It is shown that glow discharge polymerization can be visualized as a process consisting of three discharge processes. These are (1) controlled discharge of monomer, (2) electric discharge (glow discharge), and (3) glow discharge polymerization of the monomer. Before the electric discharge is initiated, a steady-state flow of the monomer is generally established. During this controlled discharge of the monomer (without electric discharge), adsorption of the monomer onto the solid surfaces in …

The Initial And Terminating Stage Of Glow Discharge Polymerization Investigated By Thickness Monitor, N. Inagaki, H. Yasuda

Chemistry Faculty Research & Creative Works

An attempt to discuss the initial stage and terminating stage of glow discharge polymerization was made by selecting the monomer system of styrene and acetylene, which differ in their condensability, and a certain polymerization procedure. Results indicate the important aspects of the initial and terminating stages of glow discharge polymerization. These aspects may not play a significant role in the study of bulk properties of plasma‐polymerized polymers or in the study of polymer deposition rate. However, the initial stage effect might influence the adhesion of the polymer. The terminating stage effect might influence the surface characteristics of glow discharge‐polymerized polymers. …

Neutron Activation Analysis Of Nuclides From Stellar And Man-Induced Nuclear Reactions, Lawrence Lee Oliver

Doctoral Dissertations

"Neutron activation and γ-counting were used to determine the relative abundances of six stable tellurium isotopes in the acid-etched residues of the Allende meteorite. The results were correlated with the isotopic compositions of xenon and the elemental abundances of helium and neon in similarly prepared residues. Nucleosynthesis appears to be the only viable explanation for the anomalous isotopic and elemental compositions observed in these residues. Our results suggest that the solar system condensed from an isotopically and chemically zoned nebula that was produced by the explosion of a supernova, concentric with the present sun.

A combination of neutron activation and …

A Thermochemical Study Of The Ore Deposits Of The Milliken Mine, New Lead Belt, Missouri, Douglas L. Rickman

Doctoral Dissertations

"The ore body at the Milliken mine is a typical Mississippi Valleytype ore deposit. Mineralization is in a dolostone and structures are subtle, but very important ore controls. The major mineralogy is simple, predominately galena, luminescent hydrothermal dolomite, sphalerite and chalcopyrite. Twenty-three additional minerals have been identified in the ores, including barite and Pb-aragonite, bot h of which have not previously been recognized in the district.

Paragenetically, the ores are very complex, with four major, distinct periods of mineralization plus numerous periods of dissolution. The paragenesis provides evidence for the dynamic, evolving nature of the ore system. Galena textures, euhedral …

Load And Resistance Factor Design Of Cold-Formed Steel Structural Members, Boonsong Supornsilaphachai

Doctoral Dissertations

"In a traditional design, the Allowable Stress method has long been used for the design of cold-formed steel structures. In this design approach, the allowable stress is always used to prevent the possible structural failure by using an appropriate factor of safety selected primarily on the basis of engineering judgment and long-time experience.

Recently, the concepts of risk and reliability analysis have been successfully applied to many fields of engineering. By applying the theories of probability and statistics, the load and resistance design criteria for steel structures have been developed for the design of hot-rolled steel shapes and built-up members. …

Electron Transport Coefficients And Excitation Processes In Gaseous Mixtures Containing Mercuric Bromide, Howard Lundgren Brooks

Doctoral Dissertations

"A comprehensive set of measurements of the electron drift velocities and apparent ion formation cross sections has been completed for gaseous mixtures containing mercuric bromide using electron swarm techniques. Results are presented for binary mixtures of HgBr₂ and the rare gases neon, argon and xenon, with the concentration of HgBr₂ varied from 0.01% to 0.2% of the total. None of the measured quantities show a temperature dependence from 100 ° C to 150 ° Cover the range studied from 1 to 100 Townsend (1 Townsend = 1 Td = 10^-17 volt•cm²) in all of the …

Kinetic Processes In A High Pressure Laser Generated Plasma, Danny Joe Krebs

Doctoral Dissertations

"A dense sodium vapor in a high-pressure noble buffer has been simultaneously excited by short (4 ns) laser pulses from two lasers: ii the first tuned to one of the 'D' line transitions and the second tuned to either the photoionization threshold of the 3p states near 406 nm or to a higher level 3p-nd resonance. The population densities of the excited levels of atomic sodium were measured with temporal resolution by absolute intensity measurements of excited state fluorescence. At early times (~100 ns), excited state populations are determined by energy transfer collisions between two laser-excited 3p atoms while the …

Boron Implanted Strontium Titanate, Connie Macdonald Cooper

Doctoral Dissertations

"Single crystals of strontium titanate implanted with boron were found to have highly conductive surface layers. The effects of varying dose from 10¹⁶ to 10¹⁷ ions/cm², implantation voltage from 50 to 75 keV, and annealing conditions on the room temperature surface resistance and Hall mobility are presented in this study. A major result is that, for the most part, variation of the implantation voltage did not have a major effect on the sheet resistances obtained by boron implantation of strontium titanate, while dose and annealing conditions have major effects.

Doses of 5 X 10¹⁶ ions/cm …

An Investigation Of The Nickel-Cobalt Occurrence In The Southeast Missouri Mining District, David Ray Jessey

Doctoral Dissertations

"A study of the occurrence of nickel and cobalt in the Southeast Missouri Mining District has revealed several significant geochemical trends and mineralogical relationships. Regional geochemical studies indicate that the greatest concentration of nickel and cobalt occurs in the Fredericktown area. Mines in the Viburnum Trend also have significant concentrations of these metals. Studies of the Viburnum Trend have established that both nickel and cobalt decrease in concentration southward from the Magmont mine to the Brushy Creek mine, increase at the Fletcher mine, and decrease again at the Sweetwater mine.

A detailed geochemical study of the Buick mine has shown …

Excitation Transfer In Ion Rydberg-Atom Collisions, R. (Ronald) E. Olson

Physics Faculty Research & Creative Works

Recently, electron-loss cross sections were presented by Kim and Meyer [Phys. Rev. Lett. 44, 1047 (1980)] for 40 keV/amu N3+ + H**(n) collisions which scaled as n3.12, where n is the principal quantum number of the excited H0. Such results are in contrast to an n2 scaling predicted by classical and first-Born theoretical methods. Our calculations indicate that a major component of the experimentally observed ion signal was due to Stark ionization by deflector grids of highly excited H0 produced in excitation-transfer collisions. Inclusion of the excitation process in a theoretical interpretation reveals qualitative agreement between theory and experiment and …

N,L Distributions In Aq++H Electron-Capture Collisions, R. (Ronald) E. Olson

Physics Faculty Research & Creative Works

The classical-trajectory Monte Carlo method has been used to determine product-state distributions in Aq++HA(q-1)+(nl)+H+ electron-capture collisions at energies 50 and 100 keV/amu for fully stripped ions in charge states q=1to 20. In the energy region studied, the electron-capture products are found to populate predominately principal quantum numbers around nmq34. Such behavior implies the captured electron tries to preserve both its original orbital energy and dimensions after the electron-capture collision. The orbital-angular-momentum quantum numbers l are more highly peaked than statistical to large l values for nnm. © 1981 The American Physical Society.

A Performance Study Of A Microcomputer-Iimplemented Microcomputer-Implemented Fsk Receiver, Paul D. Stigall, Rodger E. Ziemer, Van T. Pham

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

Verification Of The Kalman Conjecture For Systems Containing Numerator Dynamics, Abdelhamid Djebrane, D. Ronald Fannin

Electrical and Computer Engineering Faculty Research & Creative Works

The Kalman conjecture is shown to be true for certain systems of arbitrary order containing numerator dynamics. Simple restrictions on the system parameters are obtained such that the validity of the Kalman conjecture can be easily tested. Copyright © 1981 by The Institute of Electrical and Electronics Engineers. Inc.

Similarity In Phase Diagrams Between Ionic And Nonionic Surfactant Solutions At Constant Temperature, K. Shinoda, H. Kunieda, N. Obi, Stig Friberg

Chemistry Faculty Research & Creative Works

No abstract provided.

Distribution Of Polymer Deposition In Glow Discharge Polymerization In A Capacitively Coupled System, N. Inagaki, H. Yasuda

Chemistry Faculty Research & Creative Works

The manner by which polymers created by plasma uniformly deposit onto substrates was sought. By rotating the substrate placed midway between electrodes, completely uniform distribution of polymer deposition was accomplished, and the deviation of the polymer deposition in a radius direction of the rotating substrate was within experimental errors. Materials of the substrate on which the polymer deposited had no influence on uniformity of polymer deposition, but the electrical circuit of power source, i.e., grounding an electrode, markedly disturbed the uniformity. Thickness of polymers deposited on the substrate was linearly proportional to reaction time. Surface energies of deposited polymers prepared …

The Structure Of Lamellar Lyotropic Liquid Crystals From Lecithin And Alkanediols, Magda A. El-Nokaly, Larry D. Ford, Stig Friberg, David W. Larsen

Chemistry Faculty Research & Creative Works

Lamellar liquid crystals from lecithin and alkane diols were studied to determine the composition range of stability and geometrical dimensions using low-angle X-ray scattering. An estimation of the dislocation pattern was made from the optical pattern in polarized light. The ethylene glycol gave the widest range of stability for the lamellar structure, the range being reduced toward heptane diol, the longest member to give liquid crystals. The interlayer spacing was reduced with increasing chain length of the diol and the dislocation pattern remained identical. © 1981.

Thermodynamic Properties From A Cubic Equation Of State: Avoiding Trivial Roots And Spurious Derivatives, Bruce E. Poling, Edward A. Grens, John M. Prausnltz

Chemical and Biochemical Engineering Faculty Research & Creative Works

A simple method is presented to find and avoid trivial roots and spurious derivatives for a cubic equation of state. The method's utility is demonstrated with some illustrative distillation calculations. © 1981, American Chemical Society. All rights reserved.

The Missouri Miner, December 11, 1980

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, December 04, 1980

The Missouri Miner Newspaper

No abstract provided.

Missouri S&T Magazine, December 1980, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

Thermal Decomposition Kinetics Of Asf5-Doped Polyacetylene In Vacuum, T. Inoue, J. E. Osterholm, H. Yasuda, L. L. Levenson

Physics Faculty Research & Creative Works

Electrical conductivity measurements, mass spectra of desorbing species, and ESCA surface analysis are reported for AsF5-doped polyacetylene heated between 50 and 130°C in vacuum. All measurements indicate first-order decomposition kinetics with activation energies between 13 and 20 kcal mole-1. Decomposition leads to the desorption of AsF3 and F2. Metallic arsenic remains in the polyacetylene as a decomposition by-product.

High Flux Beam Source Of Thermal Rare-Gas Metastable Atoms, D. W. Fahey, William F. Parks, Laird D. Schearer

Physics Faculty Research & Creative Works

A high-flux beam source has been constructed for the production of helium, neon and argon metastable atoms. The source is a DC electric discharge maintained in an expanding gas. A metastable flux of 3.5*1014, and 7.2*1013 atoms s-1 sr-1 has been achieved with most probable energies of 66, 72 and 74 meV for the helium, neon and argon sources, respectively. Time-of-flight measurements showed the widths of the respective velocity distributions to be 45%, 27% and 27%.

The Inert Gas Effect On The Rate Of Evaporation Of Zinc And Cadmium, P. C.S. Wu, Thomas J. O'Keefe, Fred Kisslinger

Materials Science and Engineering Faculty Research & Creative Works

An experimental study has been made to investigate the effect of argon and helium on the rate of evaporation of zinc and cadmium under one atmosphere pressure at temperatures ranging from 500 to 850°C. The experimental results were compared with the maximum rates calculated using the effusion formula as well as with values obtained using two different types of equations based on kinetic theory, diffusion theory, and empirical data. Equations have been derived for expressing the rate of evaporation of zinc and cadmium in both argon and helium as functions of temperature of the liquid zinc and cadmium. It was …