Digital Commons Network^™

Development Of A Simple Vibration Model For Predicting The Structural Dynamics Of An Hcci Engine, Jeffery A. Massey

Doctoral Dissertations

"The hypothesis tested in this work is that the surface vibration and radiated sound of an engine operating under HCCI combustion is dominated by the free vibration response of the engine's structural components to an impulsive loading brought about by the rapid energy release of the HCCI combustion process. Recent work by the author has shown that classical vibration theory describing the dynamic response of a single-degree-of-freedom (SDOF) oscillator may capture the major characteristics of the engine surface vibrations. Through an experimental investigation of HCCI combustion engine dynamics this model has been developed further.

A band level analysis of measured …

Inherent And Model-Form Uncertainty Analysis For Cfd Simulation Of Synthetic Jet Actuators, Daoru Frank Han

Masters Theses

"A mixed aleatory (inherent) and epistemic (model-form) uncertainty quantification (UQ) analysis method was applied to a computational fluid dynamics (CFD) modeling problem of synthetic jet actuators. A test case, (Case 3, flow over a hump model with synthetic jet actuator control) from the CFDVAL2004 workshop was selected to apply the Second-Order Probability framework implemented with a stochastic response surface obtained from Quadrature-Based Non-Intrusive Polynomial Chaos (NIPC). Three uncertainty sources were considered: (1) epistemic uncertainty in turbulence model, (2) aleatory uncertainty in free stream velocity and (3) aleatory uncertainty in actuation frequency. Uncertainties in both long-time averaged and phase averaged quantities …

Spiking Neural Networks And Their Applications, Cameron Eric Johnson

Doctoral Dissertations

"Artificial neural networks (ANNs) have been developed as adaptable, robust function approximators for at least the last quarter-century. They have progressed through two generations, and the third is now under development. Spiking neural networks (SNNs) seek to improve on previous generations in two ways: by using a more biologically-inspired neuron, they are shown to be capable of more complex calculations; incorporating polychronous properties of highly-recurrent networks with delays of different lengths on each synapse to achieve large numbers of possible patterns with relatively few neurons and synapses.

Abstracted spiking neurons have been used as a third-generation activation function in a …

Calcium Wire Ladle Treatment To Improve Cleanliness Of Centrifugal Cast Steel, Edith Yolanda Martinez Silva

Masters Theses

"Centrifugal casting provides the opportunity of combining large centrifugal forces and directional solidification to reduce non-metallic inclusions in the cast steel product. Calcium treatment in the ladle has the potential of reducing and modifying non-metallic inclusions to achieve better machinability and mechanical properties. The objective of this research is to analyze the combined effects of calcium wire ladle treatment and centrifugal casting on the number, size, composition and morphology of non-metallic inclusions in centrifugally cast steel products.

All experiments were completed at an industrial foundry. The experiments involved feeding calcium wire into the ladle after argon oxygen decarburization (AOD) and …

Using Conditional Probability To Predict Solar-Powered Pump-And-Treat Performance, Erica RenéE Collins

Masters Theses

"Green and sustainable remediation can be further environmentally friendly by using renewable energy systems in place of utility-provided power. This project includes the installation of a single-axis tracking photovoltaic (PV) array at a former dry cleaning site that is undergoing remediation under the Missouri Department of Natural Resources (MODNR) Dry cleaning Environmental Response Trust (DERT) Fund program. The PV array provided power to a positive displacement piston pump that extracted ground water from a 15 m deep monitoring well. The tetrachloroethene (PCE)-contaminated ground water was treated using granular activated carbon (GAC) units prior to discharge to the local publicly owned …

Development And Testing Of Chemically-Based Self-Consolidating Concrete, Mark Daniel Ezzell

Masters Theses

"Self-consolidating concrete (SCC) possesses several characteristics that can benefit the concrete construction industry including accelerated construction, a reduction in labor and equipment, and a reduction in construction noise through eliminating or reducing the need to vibrate the concrete. However, SCC has some potential downsides. These problems can usually be attributed to higher paste content, higher fines content, rounder aggregate, and higher water to cement (w/c) ratios used to increase the flow of the concrete. The goal of this research project was to develop a SCC that had improved material properties through the use of chemical admixtures instead of modifications to …

Design Of A Conditioner For Smoothing Wind Turbine Output Power, Murali Bottu

Masters Theses

"As a result of wind speed intermittency, wind turbine output power can be highly variable. The large variability in output power can adversely impact local loads that are sensitive to pulsating power. To mitigate large swings in power, the wind turbine output power can be smoothed by using a small energy buffer. A power conditioner is proposed to smooth the wind power output by utilizing the energy of an ultracapacitor. The conditioner is based on a single phase voltage source inverter (VSI) connected between the grid interconnection point and the ultracapacitor. The shunt VSI injects or absorbs active power from …

Bond Strength Of High-Volume Fly Ash Concrete, Michael Hayse Wolfe

Masters Theses

"Concrete is the most consumed man-made material in the world. Unfortunately, due to the production of cement, concrete has a large carbon footprint. Replacement of cement with fly ash, an industrial waste product, offers a sustainable alternative. The goal of this research was to explore the feasibility of using high-volume fly ash (HVFA) concrete for structural applications by testing the material's reinforcement bond properties. A series of pull-out tests and beam splice tests were performed on specimens with a 70 percent fly ash replacement of cement and then compared to identical tests performed on control specimens cast from a 100 …

Towards On-Line Voltage Stability Assessment Using Synchrophasors, Himanshu Subandhu Hirlekar

Masters Theses

"Voltage instability has become a growing concern in the operation of power systems in recent years. The reason is that power systems all over are being operated with reduced margins because of increased demand exacerbated by a general reluctance to invest in improvement of the electric grid infrastructure. Until recently it was difficult to predict voltage instability in the on-line environment. However, advances in technology has made possible the on-line monitoring and assessment of voltage stability. Synchrophasors is a relatively new technology in the field of power systems which allows system operators to monitor the system conditions at specific measurement …

Field Programmable Gate Array Based Multiple Input Multiple Output Transmitter, Richa Shekhar

Masters Theses

"MIMO is an advanced antenna technology compared to Single Input Single output (SISO), Multiple Input Single Output (MISO), and Single Input Multiple Output (SIMO) and is used to obtain high data rate in the system. Multiple-Input Multiple-Output (MIMO) systems have at least two transmitting antennas, each generating unique signals. However some applications may require three, four, or more transmitting devices to achieve the desired system performance. This thesis describes a comparison between different approaches like the microcontroller, ASICs and the FPGA available in the market for baseband signal generation. It also describes the design of a scalable MIMO transmitter, based …

Ozone Uptake Rates And Secondary Product Emissions Of Green Building Materials, Seth Paul Lamble

Masters Theses

"Building materials considered "green" were tested for their ability to remove ozone and their potential to generate undesirable byproducts such as aldehydes. Three types of ceiling tile were tested, along with seven flooring materials and eight wall materials. These materials were selected based on "green" criteria. For several this means they were recycled or produced from renewable resources. Others were designed to be low emitting, or due to their composition were likely to be low emitting. Ozone deposition velocities ranged from 0.25 m h-1 for a type of resilient linoleum type flooring to 8.23 m h-1 for a clay based …

Longitudinal Evaluation Of A Learning System For Teaching Geographical Information System Within The Context Of A Geotechnical Problem, Aparna Sukhavasi

Masters Theses

"A learning system, to train civil engineering students to apply Geographical Information Systems (GIS) in geotechnical problems, was evaluated over a period of 5 years, hence longitudinal. The system was tested with a series of iterations consisting of usability tests and subsequent modification, which were followed by a series of applied evaluations within the context of class lab sessions. The principal goals of this evaluation were to determine the overall effectiveness of the system and the factors that affected student learning. The first evaluation was conducted in 2004; and included a control group that played a "game" related to the …

Installation And Performance Evaluation Of Coaxial Cable Sensors For Crack And Corrosion Detection, Iana Muchaidze

Masters Theses

"Even under service loads, reinforced concrete (RC) structures can develop cracks that result in excessive deflection of the structures and provide passages for moisture to corrode steel reinforcement. It is thus critical to develop a simple, cost-effective tool for real-time crack monitoring and associated corrosion detection that may affect the engineering maintenance of RC structures. The objectives of this study include: (1) to develop a die-cut manufacturing process of coaxial cables with spiral outer conductors, (2) to quantify the sensing properties of a miniaturized topology-based crack sensor, (3) to investigate the effectiveness of various sensor installation procedures in RC applications, …

Impact Of Combustion Phasing On Energy And Availability Distributions Of An Internal Combustion Engine, Shawn Nicholas Wildhaber

Masters Theses

"High fuel efficiency has become an extremely desirable trait for internal combustion engines. This motivation has driven extensive research on methods to improve fuel efficiency on engines of various sizes. Many of these methods involve changes to the properties of the combustion process. One way to induce these property changes is through varying the phasing of combustion. Combustion phasing can be defined as the time in the engine cycle, specifically the compression and expansion strokes, where combustion occurs. A change in combustion phasing causes a change in combustion duration. The duration of combustion impacts how the energy and work potential …

Uncertainty Quantification Integrated To Computational Fluid Dynamic Modeling Of Synthetic Jet Actuators, Srikanth Adya

Masters Theses

"The Point Collocation Non-Intrusive Polynomial Chaos (NIPC) method was applied to a stochastic synthetic jet actuator problem to demonstrate the integration of computationally efficient uncertainty quantification to the high-fidelity CFD modeling of Synthetic Jet Actuators. The uncertainty quantification approach was first implemented in two stochastic model problem cases for the prediction of peak exit plane velocity using a Fluid Dynamic Based analytical model of the Synthetic Jet Actuator, which is computationally less expensive than CFD simulations. The NIPC results were compared with direct Monte Carlo sampling results. To demonstrate the efficient uncertainty quantification in CFD modeling of synthetic jet actuators, …

A Numerical Study Of Novel Drag Reduction Techniques For Blunt Bodies In Hypersonic Flows, Christopher Marley

Masters Theses

"Numerical simulations of a full three-dimensional hemispherical body in hypersonic flow are conducted and innovative techniques involving forward injection of gas from the stagnation point of the sphere are investigated; techniques include annular (ring) and swirled injection both with and without upstream energy deposition. Objectives of the analysis are the assessment of 1) drag reductions achieved on the blunt body (including the detrimental drag effect caused by the forward-facing injection itself) and 2) stability characteristics of the jet. Studies are conducted at free-stream Mach numbers of 10 and 6.5 at standard atmospheric conditions corresponding to 30 km altitude. While centered …

Characterization Of Shielding Effectiveness For Metallic Enclosures, Nicholas Bennett Mentesana

Masters Theses

"This topic discusses and verifies an equation for estimating the shielding effectiveness of metallic enclosures through the use of numerical simulations. Using ideas from Bethe's "Theory of Diffraction by Small Holes", a previous student from the Missouri S&T Electromagnetic Compatibility Laboratory developed an equation that would yield an envelope prediction for the worst-case EMI from an aperture array backed by an over-moded cavity. Min Li (PhDEE '99) used results from measurements, simulations, and physics-based equations to formulate a simple equation that would predict these EMI levels. The main purpose of this thesis is to revisit this work and determine when …

Effects Of A Nickel Reactor Liner And Other Reaction Variables During Supercritical Water Reformation Of Glycerin, Michael S. Stever

Masters Theses

"The non-catalytic reformation of glycerin using supercritical water was conducted in a 400-mL tubular reactor constructed of Haynesʼ Alloy 230. The evaluated parameters for this thesis include water-to-glycerin molar ratios ranging from 3 to 24 and reactor temperatures ranging from 500⁰C to 700⁰C. In addition, experiments were performed using the Haynes' Alloy 230 reactor both without a liner and with a Nickel 201 liner. Space time was maintained at approximately 100 seconds and the reactor pressure was kept constant at 24.1 MPa. The resultant effect on product gas composition and carbon gasification was determined. The product gases consisted of a …

Morpho-Tectonic Analysis Of The Tekeze And The Blue Nile Drainage Systems Of Northwestern Ethiopian Plateau, Ethiopia, Elamin Hassan Dai Ismail

Masters Theses

"This study examines the morpho-tectonic evolution of the drainage system in the northwestern Ethiopian plateau by focusing on the Tekeze and the Blue Nile Rivers. The plateau is underlain by Precambrian crystalline rocks, overlain by Mesozoic sedimentary section that is topped with a 1-3 km thick pile of Oligocene-Quaternary volcanic rocks. It is bounded in the east and southeast by the Afar Depression (AD) and the Main Ethiopian Rift (MER). Satellite derived Digital Elevation Models are analyzed using ArcGIS and RiverTools to extract morpho-tectonic parameters of tributaries of the Tekeze and Blue Nile Rivers including Normalized Steepness Index (K_{sn …}

Computational Investigation Of Plasma Actuator As An Active Flow Control Strategy Of Laminar Separation Bubbles, Justin Roger Aholt

Masters Theses

"A parametric computational study designed to examine the plausibility of an external body force generated by active means, such as a plasma actuator, as a means of controlling a Laminar Separation Bubble (LSB) over an airfoil at low Reynolds numbers was conducted. Computational Fluid Dynamics (CFD) was employed to characterize the effect that a body force, localized to a small region tangent to the airfoil surface, might have on an LSB. In this study, the effects of altering the strength and location of the "actuator" on the size and location of the LSB and on the aerodynamic performance of the …

Managing A Solar Sensor Array Project: Analyzing Insolation & Motivation, Beth A. Yount

Masters Theses

"The renewable power industry is rapidly growing today and is in need of much data to augment the advancement of the field. Photovoltaic technology, while making substantial improvement over the last 60 years, still has some significant hurdles to overcome. When shading, dust, or damaged cells reduce the power output of one panel, the traditional series-parallel configurations make it so every panel in series with that lower current panel, will also have its current lowered; this lowers the overall power output of the array significantly. Advancements in configurations and converters could change this phenomenon and dramatically increase a solar array's …

Simultaneous Measurement Of Temperature And Strain By Three-Section Phase-Shift Long Period Fiber Grating, Hongbiao Duan

Masters Theses

"Long period fiber gratings (LPFGs) have found many applications as sensors to measure strain, temperature, refractive index and other physical parameters. In various sensing applications, the cross-sensitivity between two parameters, especially the temperature cross-sensitivity, has been a major difficulty to achieve high accuracy measurement. One of the solutions is to develop LPFG sensors for simultaneous, multi-parameter measurements.

In this thesis, three-section phase-shift (PS) LPFGs were fabricated and investigated for simultaneous measurement of temperature and strain. Compared with a two-section PS-LPFG, a three-section PS-LPFG has two deeper resonance sub bands and a larger separation between the two bands. The strain, temperature …

Mutation Of The Hof1 Pest Domain Affects Cytokinesis In Budding Yeast, Katherine E. Stockstill

Masters Theses

"Cytokinesis is the division of a cell into two daughter cells. Cytokinesis failure results in polyploidy, which may contribute to tumorigenesis or cause cell death. The Saccharomyces cerevisiae protein Hof1, which is required for efficient cytokinesis, is phosphorylated during mitosis. The hypothesis that MEN (mitotic exit network) dependent phosphorylation regulates Hof1 degradation, triggering completion of cytokinesis was tested. Hof1 contains a PEST sequence, which is rich in proline, glutamic acid, serine, and threonine, and is believed to be involved in protein degradation. To test the hypothesis, we created two non-phosphorylatable mutants of the Hof1 PEST domain tagged with GFP. The …

Solar Powered Residential Hydrogen Fueling Station, Aanchal Shah

Masters Theses

"Interest towards the hydrogen fuel technology is increasing but its potential benefits will not be felt until hydrogen vehicles and the fueling infrastructure captures a substantial market share. Though there has been a rapid progress in the hydrogen fuel cell technology, a major challenge to the commercialization of fuel cell vehicles is the lack of hydrogen fueling infrastructure. The development of a commercial hydrogen fueling station is a challenge due to its high initial cost and safety concerns. Residential fueling stations provide an innovative solution to this issue since they also produce electricity and heat for the residential buildings in …

Optimization Of Textual Affect Entity Relation Models, Ajith Cherukad Jose

Masters Theses

"Affective computing is a recent research area in computer science which deals with the design and development of systems that can recognize, interpret and process human affects/emotions. Various research projects in the past have focused on affect sensing and processing raw textual data. One such research effort conducted at the Oak Ridge National Laboratory (ORNL) has introduced an affect propagation algorithm which can generate affective relationships between entities contained in a given textual document. The algorithm depends upon a set of real-valued numeric parameters for which the best possible values are unknown. This thesis describes three different contributions to ORNL's …

Rapid Simulation Of The Statistical Variation Of Crosstalk In Cable Harness Bundles, Xiang Li

Masters Theses

"Accurate assessment of crosstalk problems in cable harnesses requires simulation methods that account for the statistical variation of harness parameters. Methods are proposed to determine the influence of the statistical variation in wire positions, the rate that wires change position (i.e. "twist"), harness height, harness density (i.e. how closely wires are packed) and circuit loads. Methods use a combination of simulation and probability theory. Simulations use the T-parameter method, a rapid simulation technique for harness bundles. Simulation time is further improved by using the mean and variance of crosstalk estimated for fixed harness parameter values to estimate the mean and …

Thermo-Physical Properties Measurement And Steel - Ceramic Shell Interactions In Investment Casting, Chirag Mahimkar

Masters Theses

"Investment casting is a process in which a ceramic shell is prepared on a wax or foam pattern. The wax is melted out or the foam is burnt out and the shell is sintered to have sufficient strength to withstand casting conditions. The investment casting process is very important as it produces near net shape castings which reduce the need for subsequent operations of castings like machining etc. Investment casting shells are subjected to a number of heating cycles during pattern removal, firing, preheating before pouring and finally during solidification. The thermo-physical properties of the shell play an important role …

Location Privacy Policy Management System, Arej Awodha Muhammed

Masters Theses

"The advance in wireless communication and positioning systems has permitted development of a large variety of location-based services that, for example, can help people easily locate family members or find nearest gas station or restaurant. As location-based services become more and more popular, concerns are growing about the misuse of location information by malicious parties. In order to preserve location privacy, many efforts have been devoted to preventing service providers from determining users' exact locations. Few works have sought to help users manage their privacy preferences; however management of privacy is an important issue in real applications. This work developed …

Heat Transfer Augmentation In Rectangular Ducts Due To Passive Flow Destabilization, James Jackson Tinsley

Masters Theses

"The following thesis documents the comparison of surface enhancements in rectangular ducts for heat transfer enhancement of the air-side of off-road heat exchangers. Two sets of experiments were completed, one utilizing air as the working fluid, and the other utilizing water. Five air geometries and four water geometries were studied, including those with crosswise bumps, longitudinal vortex generators, and a unique rifling geometry. A smooth test section was also tested in the water experiments to verify the experimental setup. Such verification had been performed previously for the air experiments by Rucker [2007]. The experiment involved an applied constant heat flux …

Scholarship In International Technical Communication, 1950-1989: A Historical Study, Xiaoyan Huang

Masters Theses

"This thesis is a study of the published scholarship in international technical communication from 1950 to 1989. It provides insight into the four decades' worth of scholarship as well as a resource for the development of present and future scholarship in international technical communication. It attempts to answer the following research questions: What did scholars of international technical communication study in each decade? What are the similarities and differences among the four decades in terms of scholarship in international technical communication? What are the strengths and weaknesses of the relevant scholarship in the four decades? What can we learn from …