Digital Commons Network^™

The Missouri Miner, September 30, 1966

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, September 23, 1966

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, April 22, 1966

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, February 11, 1966

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, January 07, 1966

The Missouri Miner Newspaper

No abstract provided.

Effect Of Artificial Roughness On Convection, Lee W. Burford

Masters Theses

"Considerable work has been done in recent years, and is still being done, to find ways of increasing the heat transfer rate in fluid heat exchangers. One particular type of potential heat exchanger that has been studied analytically, as well as experimentally, is the use of artificially roughened tubing.

The test sections used in this experiment consisted of four aluminum pipes, three of which have been artificially roughened internally by machining ninety- degree V-shape grooves along the axis of the pipes. The grooves were 30/1000, 60/1000, and 90/1000 inches in depth. The remaining pipe was a smooth test section with …

A Study Of Sedimentation In A Well Regulated Major Drainage Basin - The Monongehala, Allegheny And Upper Ohio Rivers, William S. Wood

Masters Theses

"This investigation is concerned with the study of various programs employed in reducing and controlling sediment. The measures employed by the U.S. Soil Conservation and Forestry Services to control and reduce erosion, the primary source of sediment, was studied. The flood control and river navigation structures constructed and operated by the U.S. Army Corps of Engineers and the effect of these structures on sedimentation was also evaluated. State and local community regulation and control of exploited natural resources was studied to determine their influence on the generation and control of sediment.
The Allegheny, Monongehala and upper Ohio River Drainage Basin …

Dynamics Of Disordered Harmonic Lattices, Daniel N. Payton Iii

Doctoral Dissertations

"Extensive numerical and analytic studies of vibrational spectra, normal modes, thermodynamic properties, and dynamical properties of harmonic systems with varying degrees of substitutional disorder have been made. The effects on observable properties of random mixtures of two or more species of atoms with differing masses and differing couplings to nearest-and next-nearest-neighbors have been investigated. Using the IBM-7030 digital computer, spectra for linear chains of 100,000 atoms have been obtained. Calculations in two and three dimensions have been limited to arrays of approximately 1000 atoms. Varying composition, mass ratio, and order affect the spectra in two and three dimensions in ways …

Checking Rigid-Framed Structures By Extended Moment-Area Equations, Lucky Li-Chi Chow

Masters Theses

"Using the known moments obtained from the moment distribution solution, the extended moment-area equations are used to check whether or not delta x, delta y, delta theta are truly zero, or are any other quantity they are supposed to be. In order to get a reasonably correct answer, a solution must meet both the elastic checks and the static checks for their equilibrium and compatibility functions. Using the extended moment-area equations, the magnitudes of the slopes and deflections at all of the joints in framed structures can be found easily"--Abstract, page ii.

Bending Of Isosceles Right Triangular Plates, Ping-Tung Huang

Masters Theses

"In this thesis the series expansion method is used to obtain the moments and deflections of an isosceles right triangular plate bent by arbitrary transverse loads. The method is based on using an antisymmetric load on a square plate. Two boundary conditions are solved and the numerical results obtained for these cases are tabulated"--Abstract, page ii.

A Study Of Stress Distribution And Measurement Of Axial Strain Around A Pilot Hole During Overboring, Varakantham Sreedhar Reddy

Masters Theses

"Stress distribution around a pilot hole during overcoring was investigated. A study of axial strain on the borehole surface was undertaken. Two-dimensional epoxy resin models were prepared and stress frozen in a centrifuge. The stress-frozen models were examined under a direct-viewing polariscope. The magnitude of axial strain and the effect of strain relaxation on the pilot hole were measured on blocks of brittle materials. Factors contributing to discing of core during the overcoring operation were investigated and a mechanism of failure postulated. The loading conditions simulating in situ, core and bit pressures were applied individually to the brittle models and …

Modal Characteristics Of A Vibrating Truss, Edd Leighman Ghent Jr.

Masters Theses

"In this thesis, a complete technique is presented for the vibration analysis of any planar structure which can be classified in the broad category of trusses or frames. Although a theoretical backdrop is included for the' sake of completeness, the intent is to provide a technique that is readily adapted to computer usage and can be handled with a minimum of confusion or misunderstanding.

The problem is solved by the use of a displacement technique wherein the inertia and stiffness properties of a structure are calculated by superimposing the contributions of each component of the structure. The calculation of these …

Phase And Amplitude Distributions Of An Unsymmetrically Fed Ground Plane Aperture, Leslie Blumberg

Masters Theses

"An anechoic chamber for use in the B-12 KHz range was designed and built for the purpose of obtaining the far field patterns of antennas and radiation systems. This chamber was evaluated and compared with various types of anechoic chambers from the standpoint of their "room performance."

The anechoic chamber is essentially a room lined with absorbing material, effective at microwave frequencies. The purpose of the absorbing material within the room is to present the reflection of the energy incident upon the walls of the room.

Measurements of the far field radiation pattern of an aperture in a ground plane, …

The Anodic Oxidation Of Maleic Acid, Larry D. Gilmartin

Masters Theses

"The purpose of this investigation was to determine the mechanism of the anodic oxidation of maleic acid on platinized-platinum electrodes at 80⁰C. Current density-potential studies were conducted varying the parameters of maleic acid concentration and pH. The faradaic efficiency of the oxidation of maleic acid to yield CO₂ was determined. The effect of temperature on current density was also studied to determine the activation energy for the reaction. The oxidation of maleic acid occurred only in acidic solutions. The faradaic efficiency was found to be approximately 97 ± 5 per cent. A linear Tafel region was found which had a …

A Crystallographic Study Of The Pbzro₃-Pbtio₃-Bifeo₃ Ternary System., Dannie R. Clarida

Masters Theses

"The purpose of this investigation was to conduct a crystallographic study of the PbZrO₃-PbTiO₃-BiFeO₃ ternary system, where all three components are perovskites. Lead zirconate is antiferroelectric, lead titanate is ferroelectric, and bismuth ferrate is thought to be ferroelectric. X-ray diffraction analysis was employed to determine the crystallographic structure and lattice parameters.

A tetragonal region was found to exist in the area of high PbTiO₃ content. A rhombohedral region occurred in the remainder of the system with high BiFeO₃ and PbZrO₃ content, except for an orthorhombic envelope along the PbZrO₃-BiFeO₃ side of the diagram up to approximately 70 per cent BiFeO₃.The …

A Numerical Solution For Beam-Columns On Non-Linear Foundations, Wendelin H. Mueller Iii

Masters Theses

"A program for Matlock's recursive method, a numerical method which will analyze beams and columns with linearly varying spring supports, was modified to enable the solution of such members supported by non-linear springs. This modification was accomplished by an iterative technique. The final result of this paper is a computer program which can be used to solve beams or columns with non-linear spring supports, giving as output the deflection, slope, moment, shear, net load and curvature of the structure at uniformly spaced locations"--Abstract, page ii.

A Photoelastic Study Of The Stresses In A Deep Beam Using Partial Mirrors For Isochromatic Fringe Sharpening And Fringe Multiplication, Edward M. Raney

Masters Theses

"This paper is a photoelastic investigation of the stresses in a deep beam using partial mirrors to obtain isocromatic fringe sharpening and fringe multiplication. This method may be of particular value in photoelastic work for obtaining full field fringe multiplication and fringe sharpening for models which exhibit low fringe orders.

The photoelastic model used in this investigation is a deep beam with a length to depth ratio of one. A uniform load is applied over the center one-half of the beam. The beam is supported by two uniform loads distributed over a length of one-quarter the span.

A first approximation …

The Effect Of Structure On The Consolidation Characteristics Of A Clay Soil, Dale E. Sukow

Masters Theses

"This paper reports the results of an investigation conducted to establish the effect of structure on the consolidation characteristics of a clay soil. Soil structure was caused to form in the soil by the addition of electrolytes to flocculate and disperse the clay fraction of the soil.

Consolidation tests were performed on specimens of the treated soil prepared at moisture contents well above the liquid limit of the soil. The consolidation data from these tests are evaluated and comparisons are made to relate the influence of structure to the consolidation characteristics of the treated soil.

The influence of structure on …

Plastic Design Of Steel Frames For Minimum Weight, I-Chen Hung

Masters Theses

"The purpose of this study was to develop a method for weight minimization of the plastically designed frame, braced normal to its plane of action, and composed of prismatic steel members. The method accounts for the non-linear relationship between weight and moment capacity for both beams and columns. Reduction in the pure-bending fully-plastic moment in the presence of axial loading and both beam-column instability and overall frame instability due to sidesway are taken into account. Provision is made for minimization of frames employing standard sections as well as for frames whose built-up members may be chosen from a continuous spectrum. …

An Investigation Of Failure Patterns Of Layered Specimens Loaded In Uniaxial Compression, Narendra Y. B. Choudary

Masters Theses

"Uniaxial compressive strength for two and three-layered specimens was obtained with different thicknesses of layers and also for different length to diameter ratios. The fracture and failure pattern was studied. Shear and extension fractures were observed in the layers. Geometry and end conditions of the specimen had a great influence in the failure and fracture pattern.

The uniaxial compressive strength of a layered specimen was found to be lower than the weighted average strength and either low or high when compared to the arithmetic average strength, depending on the ratio of the heights of the layers. The compressive strength of …

Measurement Of The Velocity And Temperature Profiles Of Air Swirling Through A Conical Shaped Nozzle, Stephen Abner Thompson

Masters Theses

"A study was conducted to determine the velocity and temperature distributions in swirling flow of air through a converging nozzle. Radial traverses were taken at three axial positions with a specially designed pitot tube constructed of hypodermic needles. The most significant finding was the large magnitude of the radial velocity component. A combination of reversed axial flow along the nozzle axis, and an outward flow near the nozzle surface was also experienced. An increase of temperature with increasing radial position may be attributed to the Ranque-Hilsch effect"--Abstract, page ii.

Empirical Evaluation Of The Eccentric Orifice In Small Diameter Pipes, Gary A. Hinz

Masters Theses

"This investigation has taken different orifice sizes (0.3005", 0.4000", 0.5045", 0.6015") and tested their flow characteristics when used in a 1" diameter pipe. Each orifice was initially placed in a fully eccentric position, that is the circumference of the orifice was placed tangent to the inside circumference of the pipe. Data was taken with the orifice eccentric to concentric in increments of 0.050".

Plots of flow coefficient versus Reynold's number were made for each position of the four orifices tested.

Empirical equations were developed for determining the flow coefficient of the various orifice sizes placed in any eccentric position.

It …

Calibration Of An Instrument To Calibrate Accelerometers, Nader Khorzad

Masters Theses

"The purpose of this research was to calibrate an instrument with which an accelerometer could be calibrated accurately. The instruments used were a piezoelectric shaker and a modified Michelson interferometer together with necessary electronic equipment. This equipment was used to calibrate a Kistler Model 808A accelerometer.

Weight was added to the shaker in the second part of this experiment in order to determine its effect on the amplitude and frequency of oscillation of the shaker.

Results show that this instrument may be used to calibrate an accelerometer quite accurately. The weight added to the shaker will effect only the amplitude …

Fluid Flow In Pipes Of Rectangular Cross Sections, Bruce Harold Bradford

Masters Theses

"Head loss due to fluid friction was measured in smooth conduits of rectangular cross section. The data covers the laminar and turbulent range. Results were compared with previous theoretical and empirical data.

The customary practice of calculating head loss in non-circular conduits by use of the friction factor obtained on an “equivalent” circular pipe was discussed. It was found that this practice is successful in square cross sections undergoing turbulent flow. In laminar flow, however, this method is not accurate"--Abstract, page ii.

An Ac Method Of Measuring The Conductivity Of Dielectric Liquids., Henry E. Fischer

Masters Theses

"The problem undertaken in this thesis is the presentation of a method of measuring the conductivity of dielectric liquids in which the liquid is used as the parallel tank circuit of a modified Wien-bridge oscillator. The main advantage of this method is that the frequency of the voltage applied to the liquid can be varied by simply varying the oscillator frequency. This allows the selection of a frequency which is best suited to the liquid in regard to polarization and relaxation time.

An oscillator was designed, built and used in the laboratory to measure the conductivity of the dielectric liquids …

Missouri S&T Magazine, December 1965, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

Torsional-Flexural Buckling Of Thin-Walled Open Sections, Pen J. Fang, George Winter

CCFSS Library (1939 - present)

INTRODUCTION Compression members with thin-walled open sections, because of their low torsional rigidities and because their cross-sectional configuration is such that the centroid and the shear center often do not coincide, can buckle at loads well below the Euler load by interaction of torsion and bending. Fast expanding applications of such sections in civil and architectural engineering call for an extensive investigation of torsional-flexural buckling. Basic theory of torsional-flexural buckling is treated by a number of authors, I,2 and simplifications of the basic theory in the elastic range for the design purposes together with some test results were reported previously. …

The Missouri Miner, October 29, 1965

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, October 22, 1965

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, October 15, 1965

The Missouri Miner Newspaper

No abstract provided.