Digital Commons Network^™

An Investigation Of Optimum Journal Bearings., Kulin Purshotam Maskai

Masters Theses

"Not much has been done towards calculating the "Optimum Bearing" from the point of view of maximum load capacity or minimum friction. It has been found that there 1 is not much difference in the "Optimum Bearing" proportions, as calculated, considering either minimum friction or maximum load capacity

Journal bearings are commonly used and they play a very important role in reducing friction and wear. Engineers use past experience in choosing a bearing for the given conditions. A bearing design can be obtained if 'Optium Bearing' proportions are calculated as suggested by Kingsbury (1) in his article on 'Optium Conditions …

Zinc Sulfide-Sulfate Reaction Pressures, William L. Hallerberg

Masters Theses

"A static manometric method was used to find the equilibrium reaction pressure as a function of temperature for the reaction:

11 ZnSO₄ + ZnS → 4 (ZnO·2ZnSO₄) + 4 SO₂

From the reaction pressures, the standard free energy of the reaction was found to be:

ΔF⁰ = + 51,320 - 36.68 T

Using thermodynamic data for ZnSO₄, ZnS and SO₂ the standard free energy of formation of the basic salt ZnO·2ZnSO₄ was found to be:

ΔF⁰ = - 377,000 - 65.9 T cal/mole

in the temperature range 350 to 420⁰ C.

Above …

A Study Of Rotational Critical Speeds For A Multi-Mass, Multi-Span System, Pravinchandra M. Upadhyay

Masters Theses

"It is well known that the unbalanced inertia forces present in rotating shafts set up violent vibrations in a transverse direction at certain speeds known as critical speeds, whirling speeds or whipping speeds. Therefore one who deals with the design of rotating machine parts, such as turbine rotors, multi-cylinder engine crankshafts etc., must consider transverse vibrations of rotating parts.

Practical solutions for finding the critical speeds of simple rotating systems, such as a single disk on a shaft with a single span, were derived by many authors. But as the number of loads and spans increases the problem becomes complex …

Composite Beams In Building Constructions., Mahendrasinhji M. Jhala

Masters Theses

"The use of composite beams is very common in bridge and. in building construction due to the fact that a savings in material is effected.

The study herein shows a simplified procedure for design of composite beams. A number of design charts for rapid selection of a wide-flange section and the necessary cover plates are presented herein. These charts are based on economic sections of steel beams when used in a simple span, if one knows the approximate depth of the beam, slab thickness, allowable stresses in the steel and concrete and live load moment, it is very easy to …

A Study Of The Relative Electric Resistance Of Commercial Steels And Pure Iron, William Eugene Wistehuff

Masters Theses

"The change in relative electric resistance of five commercial steels, Armco Ingot Iron and Pure Iron were studied over the temperature range of 800°C to 1100°C in an attempt to correlate the phenomena of hot or red shortness with a change in the Electric resistance .

The results from the above resistance measurements were compared with mechanical tests of the same steels to show that at the point at which the iron sulfide liquid forms there is a definite change in the slope of the electric resistance vs temperature curve.

Also studied was a discontinuity in the electric resistance vs …

The Missouri Miner, November 09, 1962

The Missouri Miner Newspaper

No abstract provided.

Missouri S&T Magazine, October 1962, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

Missouri S&T Magazine, August 1962, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

The Missouri Miner, May 11, 1962

The Missouri Miner Newspaper

No abstract provided.

The Missouri Miner, April 13, 1962

The Missouri Miner Newspaper

No abstract provided.

Missouri S&T Magazine, April 1962, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

Development Of A Simple Bar Method Thermal Conductivity Test, V. J. Flanigan

Masters Theses

"A linear flow bar method type apparatus was set up for finding thermal conductivities by comparison techniques. Comparison technique consist of using a standard specimen where the thermal conductivity is known and comparing it to the unknown specimens to find their conductivity. Apparatus of this type usually uses thermocouples for the required temperature measurements, but thermistors were used in this experiment. The thermistors used required calibration to measure accurate temperatures and this was accomplished by using the known temperatures of the changes of state of some common materials. Five alloys were used to evaluate the method: SAE 1020 steel, gray …

A Study Of The Stress Distribution Around Circular Openings Using Multilayered Photoelastic Material, Donald Frank Haber

Masters Theses

"Stress analysis as applied to mine openings ranges from the completely empirical to the completely theoretical. However, it is only through the ultimate utilization of the two methods that a guide to the Interpretation of mine stress phenomenon may be obtained. The bridge between the two approaches lies in the field of model study. Specifically, this is an Investigation into determining the feasibility of using multilayered photoelastic materials in models such that a more exact approximation of the underground stress distribution around mine openings can be made.

The two major objectives in this study for determining the feasibility of using …

Porous Cooling Of A Pile, Tarsem Singh Purewal

Masters Theses

"In this investigation the problem of a limiting case of steady state one dimensional solid-fluid Newtonian heat transfer is examined in which an incompressible non-heat generating coolant fluid is flowing through a heat generating porous plate.

The effect of grain size on the Newtonian heat transfer in the porous plate with various kinds of internal heat generations is determined analytically. The temperature difference between the solid and the coolant fluid through the porous plate is determined. All the previous studies assume that in the porous plate, coolant fluid temperature and solid temperatures are approximately equal. This analysis eliminates this simplifying …

Permeability Of Poly (Ethylene Terephthalate), James G. Harvey

Masters Theses

"Corrosion is a phenomenon which has been the subject of extensive research, in order to find a way to control or completely stop it. Two general methods, either placing the material which corrodes in an anti-corrosive atmosphere or protecting the material which corrodes from the corrosive atmosphere, are the chief means of preventing corrosion today.

The second method is probably most widely used presently. One of the most important methods of protection is by means of organic protective coatings, or paints, but at best these only retard corrosion, due to the fact that corrosive media e.g. water vapor, ions etc. …

Transpiration Cooling Of A Heat Generating Porous Plate, M. K. A. Hameed

Masters Theses

"This investigation is a continuation of a thesis by T. S. Purewal. Several of the simplifying assumptions made by the above author are either ignored or the justifiability of such assumptions is probed into in order to obtain a more rigorous solution. Effects of the assorted grain size, non-Newtonian cooling, direction of coolant flow, thickness of the porous heat generating plate, specific heat of the coolant, and compressibility of the coolant are investigated in this thesis. Variation of maximum temperature of both coolant and the solid material for different types of heat source distribution are also studied.

As the grain …

Thermal Conductometer For Liquids, Yuan-Kai Chang

Masters Theses

"The published data pertaining to the thermal conductivity of liquids are of such a character that it is very difficult to determine from them the correct value, or the temperature coefficient for any liquid.

Most of the published values of thermal conductivity for liquids are evaluated at one particular temperature. It is the purpose of this investigation to design, construct and calibrate a thermal conductometer for liquids over a temperature range of 30°F to 200°F.

Since water and glycerol were the only liquids found by this investigator with published data on their conductivities as a function of temperature, they were …

A Study Of The Electro-Chemical Injection Of Ca(Oh)₂ Into Pure Kaolin Clay, Sam Michael Savas Jr.

Masters Theses

"The work presented in this thesis is the investigation and study of a possible and successful means of injecting an electrolyte solution into a fine grain soil mass with the use of electric current and to measure some of the changes of its physical properties. A NoKarb Georgia Kaolin Clay was treated by passing a preferential electrolyte solution of Ca(OH)₂ using direct current for a period of one and six days. The tests performed during this investigation included the following: (a) tri-axial tests, (b) atterberg limits, (c) pH determination, (d) moisture content change (from treatment), (e) visual settling of treated …

A Study Of The Problems Of Design Of Optimum Vibration Absorbers For Multi-Mass Systems, James C. Villegas

Masters Theses

"The purpose of this investigation was to continue the preliminary work of Burrows on the application of tuned and damped vibration absorbers to the reduction of vibratory stresses in a multi-mass torsional vibration system. A hypothetical engine system was chosen for both investigations because it had many complicating factors and gave an eminently practical subject for study.

Attention was centered on the reduction of stresses resulting at higher speeds of the machine system and on developing methods and criteria for the designing of effective absorbers where several modes of vibration exist in the operating speed range of the machine"--Abstract, page …

A Comparison Of A-C And D-C Lead Compensation From D-C Prototype Networks, Piyush Parikh

Masters Theses

"The object of this thesis is to study the difference in transient and frequency response characteristics between a prototype d-c phase lead compensating network and an equivalent a-c phase lead compensating network.

A second order servo is selected to be compensated and five d-c prototype and equivalent a-c phase lead compensating networks are designed. The frequency characteristics of the a-c networks are obtained experimentally and these of the d-c networks are obtained analytically. The characteristics of both networks are compared and their differences are studied. The transient characteristics of the d-c and a-c compensated closed-loop systems to a step input …

A Model Study Of The Behavior Of Elastic Liners In Shallow Underground Openings, Martin Samuel Oudenhoven

Masters Theses

"Models of epoxy resin were used in a stress freezing technique to determine areas of possible failure in lined circular openings. These models were loaded in a centrifuge for a fixed period of time, after which they were analyzed photoelastically. The material characteristic changes, with time, were recorded on graphs and used in the analysis.

Two types of tests were conducted; one, where the lining thickness was changed and, the other, where materials of the liner and plate material were changed.

The resulting analyses furnished proof that the greater the rigidity of the lining, the higher the stress developed in …

A Comparison Of The Load Carrying Characteristics Of Hydrostatic Thrust Bearing Using Monatomic, Diatomic, And Triatomic Gases, Joseph C. Pigott

Masters Theses

"The purpose of this investigation is to compare the load carrying characteristics of gases with different ratios of specific heat. The design, construction, and operation of an apparatus for testing and comparing the load carrying characteristics of gases are described. Several monatomic, diatomic, and triatomic gases were tested and the results evaluated and compared. The data are tabulated and displayed in a series of curves.

It was found that the monatomic gases exhibit a greater clearance for a given load and a greater total load carrying capacity than the diatomic gases which in turn have a greater clearance and total …

An Investigation Of The Deformation Textures Of Cobalt, Roy Carl Wilcox

Doctoral Dissertations

"Deformation textures of various cobalt structures as a result of cold rolling together with some annealing textures were studied. The textures of cobalt were determined using a modification of the Schulz-Decker Geiger counter technique. Pole figures of the (1011), (0001) and (1010) planes were constructed. Also, a study of the microhardness of cobalt was made.

Microhardness tests were performed on various cobalt structures, in both the cold rolled and unworked conditions. The microhardness was found to vary with the source of the cobalt, the crystal orientation, and the amount of deformation and twinning. Deformation lines about the hardness impressions diffused …

Glass-To-Sapphire End Window Seals, Edward E. Stepp, Richard A. Anderson

Physics Faculty Research & Creative Works

SAPPHIRE windows have been used in laboratory devices where radiation from the ultraviolet through the infrared must be transmitted. Sapphire windows have been valuable in chambers which contain the alkali metals, for the alkali metals are known to react with Pyrex 7740 glass and quartz leaving them pitted and darkened. This paper is a report on an improved glass-to-sapphire end window seal.

Model Analysis By The Moiré Method, David D. Kick

Masters Theses

"This study presents the use of Moiré fringes for model analysis of deflections and strains. Deflection of a beam, strain in a disk, and an Influence diagram for a frame are presented as examples of uses of the Moiré method. The necessary equations for the determination of strain using the Moiré method are also derived and presented in this work"--Abstract, page v.

A Study Of Several Commercial Steels In The Red Short Range, Jorge Alberto Espana

Masters Theses

"The red short phenomenon present in steel, was studied by means of torsion tests at temperatures between 800 and 1200⁰C. Cold drawn bars of different compositions of steels were tested, and the number of turns to failure and maximum twisting torque were plotted versus temperature.

All the steels tested, exhibited to have a certain degree of red shortness. By comparing the curves and the respective chemical analyses, the detrimental effect of sulphur and lead and the beneficial effect of manganese, was established.

Microscopic examinations revealed the intergranular nature of the cracks in the red short range. Sulphur and oxide distribution …

The Effect Of The Rolling Load On The Micro-Structure Of Low Carbon Sheet Steel, Jerry Lee Cadden

Masters Theses

"A Stanat 315, two high-four high, combination rolling mill is used to cold roll annealed, low carbon steel strips. A method of measuring the rolling load was presented. The method consisted of constructing a load cell using SR-4 strain gages attached to a steel column. The load cell was placed under the hold down screw of the rolling mill and a known load was applied. The stresses from this load were transferred to the mill housing where another SR-4 strain gage was located. The strain in the mill housing was recorded at the corresponding applied load. During rolling, the strain …

Transpiration Cooling Of A Porous Plate, Stephan A. Sayegh

Masters Theses

"Transpiration cooling has long been known as an effective way of removing heat from porous materials. This thesis is a new approach to one of the problems of transpiration cooling in the steady state.

The specific problem considered here is that of a uniform porous plate through which a liquid is forced. This liquid vaporizes at a short distance from the surface through which it is forced and leaves the porous plate at the other surface which is exposed to hot gases. It also protects the hot surface by forming an insulating layer between that surface and the hot gases. …

Mechanics Of The Voussoir Arch As Applied To Block Caving, Christopher Haycocks

Masters Theses

"The theories of ground failure in massive rock with special reference to the problem of the mechanics of block caving were studied and evaluated.

The mechanics of arch or dome formation underground were studied quantitatively using the Voussoir arch theory. The effect of shear stress on the arch stability was considered and found to affect the system only when the arch height increased beyond certain limits.

A theory of the mechanism of ground failure in an undercut block using the dome theory was advanced. Photo- elastic model studies were used to support the conclusions reached"--Abstract, page i.

An Investigation Of Lehmer's Method For Finding The Roots Of Polynomial Equations Using The Royal-Mcbee Lgp-30, James W. Joiner

Masters Theses

“The solution of the general polynomial equation f (x) = O, where f(x) = a_nxⁿ + a_n-1x^n-1 + … + a₁x = a_o, has received the attention of many mathematicians for hundreds of years and is at present in a very highly developed state. Even a cursory examination of the literature will reveal many volumes on this subject. However, this study is concerned primarily with the numerical methods for solving polynomial equations, hence the classical methods will be treated here only as they contribute to this field.

Virtually all of …