Digital Commons Network^™

Development, Application And Operating Results Of The Center Peripheral Discharge Rod Mill, David Porter Hale

Professional Degree Theses

"The use of a rod mill for producing manufactured sand is not a recent application. A Marcy Open End Rod Mill has been operating at the plant of the Sun Sand Company, Thayer, West Virginia, since 1925. In early 1940 an 8' x 12' rod mill of the open end type was installed at Shasta. Dam, near Redding, California for sand production. In 1942 work began on Fontana Dam, a Tennessee Valley Authority Project on the Little Tennessee River. The flow sheet included two 9' x 12' high discharge rod mills driven by a single 800 H.P. motor. All of …

An Application Of Skew Frequency Curves To River Stages, Vernon A. C. Gevecker

Professional Degree Theses

"Floods have occurred in the past and will occur again in the future. References to floods are incorporated in some of the early writings of man. Unfortunately though man has recorded the event, he has seldom recorded facts whereby it is possible to determine the volume of flow or the height to which the water rose. Where man has recorded the height to which water rose, much data such as channel conditions, vegetation coverage on the flood plain, etc., remains vague or unknown.

It has been only in comparatively recent times with the advent of the steamboat that man has …

Geology Of The Crystal Mine, Hardin County, Illinois, John Amsden Emery

Masters Theses

"The study of the geology and mineralization of the Crystal Mine was undertaken at the suggestion of Mr. Dodson G. Gibson of the Crystal Fluorspar Company, who allowed access to the mine and its records for this purpose. The problem was to develop a system of prospecting the so-called bedded-replacement fluorspar deposits of Hardin County, Illinois. It is believed that an economically feasible method has been developed. This method involves not only the actual finding of fluorspar, but also serves as a guide in revealing structural trends suggestive of mineralization.

The fluorspar deposits of the Crystal Mine are representative of …

Effects Of Sand Admixtures On The Physical Properties Of Soils, Necati Kanatsiz

Masters Theses

"The purpose of this study is to determine the effects of sand admixtures on the physical properties of soils. Soil may be defined as a heterogenous [sic] collection of rock and mineral fragments whose decomposition and disintegration have been brought about by the action of physical, chemical, and biological forces, working singly or in combination...In the conviction that the study of soils, with respect to highway engineering, is becoming more and more important this study was undertaken in order to learn whether the addition of sand would lead to desirable results, and if not, at least secure some further addition …

Flood Control With Retarding Basin Type Reservoirs In Meramec Basin, Missouri, Ilhan Kaya Ozbilen

Masters Theses

"When rainfall occurs that provides more runoff than can be carried within the normal channels of existing streams a flood results. The excess water overflows the valley lands, invades developed areas, and causes destruction of property or, in extreme cases, loss of human life...Many structures are built to control water: Waterways of proper depth and width provide arteries of transportation; water controlled and discharged through water-wheels provides power; water may be caught in storage basins and distributed for irrigation or water supply; and water that is an actual or potential source of damage or danger to property or to human …

A Comprehensive Traffic Survey Of Phelps County, Missouri, Clifford D. Muir

Masters Theses

"The purpose of this study is two fold. The first of these purposes is to serve as a pattern or guide for any county or township wishing to conduct a comprehensive traffic survey. The second purpose of this study is to provide traffic classification and other data on a typical county system of rural roads. Today, many counties in the United States are faced with the problem of inadequate roads, due to the modernization of the American farm. While they realize this problem exists, may county governments have developed no organized method of studying and determining their needs...When the author …

Temperature Fluctuations Within A Solid Of Finite Thickness, William Sanford Hogan

Masters Theses

"The object of this thesis is to determine by analytical methods the temperatures within a homogeneous plate of finite thickness subjected to a constant temperature on one side and a periodically fluctuating temperature on the opposite side. The heat flow in the other two directions is considered negligible in this problem. Periodic changes of temperature are frequent in nature and in engineering. The surface of the earth is heated periodically by the sun in its daily and annual cycle and the periodic temperature changes below the surface and the question to which depth these changes are appreciable were dealt with …

A Grazing Incidence Vacuum Grating Spectrograph For Far Ultra Violet Spectroscopy, Lawrey Huber Chapin

Masters Theses

"Spectroscopy, in the region of the far ultraviolet from 100 Angstroms to 1000 Angstroms, requires special equipment and techniques, inasmuch as these wavelengths are highly absorbed by air. Many gases have resonant frequencies corresponding to the wavelengths mentioned and hence absorption bands appear in the spectrograms obtained by using spectrographs for the visible region. One solution of the problem of obtaining data in this region is to construct a spectrograph from which all intervening gas molecules have been removed, thus eliminating the absorbing material. A vacuum of 10⁻⁴ mm. of mercury is necessary to reduce the absorption to a value …

A Study Of Mine Scraper Efficiency On Materials Of Different Specific Gravities, Kermit Guy Rowley

Masters Theses

"The purpose of this study is to determine the effect that the specific gravity of the material scraped has on the power consumption and the efficiency of the common types of mine scrapers. As scraper weight, rope speed, and moisture content of the muck are important factors affecting the power consumption and efficiency, these variables are the ones considered for each type scraper. Two materials of different specific gravities are used in the study with an equal number of tests run on each material"--Introduction, Purpose of Problem, page 2.

Design And Test Of An Apparatus For Rate Measurements Of Rapid Gas Reactions, Erich Rolaff

Masters Theses

"The present study on rapid gas reactions was initiated with two main goals in view. The first objective was the development of equipment and methods for the treatment of problems arising in extremely rapid gas phase reactions. In recent years, with the advent of large scale applications of gas turbines and rocket motors, the process of high speed gas reactions, especially those of combustion and oxidation have become of increasing importance...The second main goal of the work was to apply the methods and equipment developed to the investigation of chemical systems of interest"--Introduction, page 1-2.

The Temperature Within A Homogeneous Plate Of Finite Thickness, Charles R. Remington

Masters Theses

"The object of this thesis is to determine by an analytical method the temperature within a homogeneous plate of finite thickness subjected to a constant temperature on one side and a periodic fluctuating temperature, expressible in a Fourier series, on the opposite side. This problem in periodic temperature changes has not, to the author's knowledge, been solved previously. The flow of heat in the problem is considered in only one direction, the x-direction. Flow in the other two directions is considered negligible, or zero. Periodic temperature changes in the earth are of importance. The temperature changes have been used by …

The Application Of The Relaxation Method To The Solution Of Steady-State Heat Transfer Through A Concentric Square Insulator, William Edward Simpkin

Masters Theses

"It is the object of this thesis to express the relationship between the heat transfer through a square insulator of variable inside-outside dimension ratios, in terms of a concentric round insulator of the same inside-outside diameter ration, by means of a continuous curve. Mathematically speaking, this thesis will have a plot of a variable coefficient, c_s, to be used...in terms of the ratio of the width of the outside square to the width of the inside square"--Statement of Problem, page 8.

Rockbursts, Christian Maurice Colson

Masters Theses

"This paper does not pretend to originality; it is an attempt to bring to light the causes and the mechanism of rockbursts, as exposed in the literature. Furthermore, an endeavor has been made to give a comprehensive picture of the prediction, prevention, and control methods of rockbursts. Briefly, what has been done in the field of rockbursts, and what remains open to investigation is submitted to the reader. The choice of rockbursts as a thesis subject appears to be justified by the geologic interest of the question. Detailed geologic observations, and particularly the recording of all the structural features which …

A High-Temperature X-Ray Diffraction Camera And Its Application To Copper And Titanium, Robert R. Penman

Masters Theses

"The purpose of this research was threefold, and consists of the following sections: 1. Effective use of a high temperature x-ray camera, capable of reaching temperatures of 1000 ºC. 2. Investigation of the thermal dilation of certain cubic metals. 3. Accurate determination of the lattice constant (aₒ) of Beta Titanium at 900 ºC "--Introduction, page 1.

The Potassium Tungsten Bronzes, Ching Hou Ma

Masters Theses

"The tungsten bronzes are a series of substitutional solid solutions of alkali or alkaline earth metatungstates and tungstic oxides. They are not really metallic alloys or intermetallic compounds but they possess some marked metallic properties such as metallic luster, good electric conductivity, high specific gravity, etc. For this reason the name of "bronzes" is applied to them"--Introduction, page 1.

Investigation Of The Effect Of Absorption Tower Size Upon Overall Mass Transfer Coefficients, James Robert Murrell

Masters Theses

"The purpose of this research project was to obtain data and determine whether or not a correlation exists between tower size and the overall mass transfer coefficient for a packed tower. A constant ratio of tower diameter to packing diameter of twelve to one was maintained. Three absorption towers were used; a twelve inch diameter iron tower, a six inch diameter iron tower, and a three inch diameter glass tower. One inch, one-half inch, and one-fourth inch Raschig rings were used in the corresponding towers as packing. The system used was the absorption of acetone by water from an acetone-air …

The Development Of Plans For A National Airport For Ankara, Turkey, Mehmet Ragip Samli

Masters Theses

"'The present rapid development of general interest in aviation has brought to the front a new field of engineering. Development of the airplane has already reached a stage where the limit of its usefulness seems fixed only by the places which may be provided for taking off and landing. Due to the newness of the problem, not every one on whom responsibility rests recognizes the fact that the selection of the proper site and location for an airport is just as much an engineering problem as are its design and construction.'

The Turkish government began construction or the Ankara-Esenboga airport …

Calibration Of Weirs By Means Of Critical Flow And Specific Energy, Robert A. Rapp

Masters Theses

"For many years man has been relying more each day upon metering devices to measure the flow of fluids in industry. The orifice, orifice meter, venturi meter, pitot tube, nozzle, flume and the weir have been employed, each having its own particular advantage.

In this parade of metering progress, the contracted weir has long been the forgotten brother of the suppressed weir. In almost every textbook on hydraulics or fluid mechanics, the following words appear, "end contractions are to be avoided where the weir cannot be calibrated". This skepticism and the length or absurdity of some contracted weir formulas led …

Safety And Health In Mining, John Philip Lacke

Masters Theses

"The mining industry has long been criticised severely because of its high rate of accident occurrence. Statistics, which, however, are not strictly comparable show that the accident-frequency rate in all mining is currently about three times and the accident severity rate is about seven times as great as the average for general industrial work in the United States. Figures such as these are by no means comforting to mining men. They constitute a challenge to the industry that cannot be ignored.

It must be remembered that any type of mining is more hazardous than most or the other major occupations. …

Construction And Operation Of A Vacuum Retort Pilot-Plant For Distillation Of Alloys, Robert Frederick Doelling

Masters Theses

"The widespread appearance of large scale vacuum systems operating commercially in the micron range of pressures has initiated a new field of industrial endeavor, vacuum engineering. The ever increasing number of applications of vacuo in commercial processes and laboratory research has stimulated the design and improvement of vacuum equipment, and at the present time equipment may be obtained to meet practically any need. In turn, the variety of available tools has directed the engineers attention to improving old processes and developing new ones through the utilization of vacuum techniques ... The possibility of producing a relatively high purity silver in …

The Freezing Temperatures Of The System Aniline-Ortho Toluidine, Ray W. Fahien

Masters Theses

"The purpose of this investigation was to determine the freezing temperatures of the system aniline-ortho toluidine and to speculate on the theoretical significance of these results. The properties of this system are of considerable practical engineering interest since the system falls in a class of low-freezing organic mixtures which may have value as fuels for jet propulsion devices required to operate at extreme altitudes or in Arctic regions. Since nitric acid has been found to be a very effective and convenient oxidizer, the search for a suitable fuel to be used in combination led to aniline as having the most …

Effects Of A Reverse Order Of Firing Using Millisecond Delay Electric Blasting Caps In A Quarry Operation, Reginald John Jones

Masters Theses

"Evidence of the steady increase in the production of quarries is a reflection of the improved blasting practices that are being used. New explosives, the new millisecond electrical blasting caps and the endless experimentation carried on by both manufacturer and operator continue to aid or better the old methods of quarry blasting. In many instances the better results were obtained from practices hitherto unknown or at least unused. This report describes the results obtained from comparing quarry rounds shot in the accepted firing order and those shot in the reverse order of firing. The purpose of the report is to …

Hydraulic Scale For Measurement Of Dynamometer And Other Forces, John Richard Barton

Masters Theses

"The object of this investigation is to design, build, test, and develop, a hydraulic type scale primarily to be used for measuring dynamometer forces. The scale however is not limited to use on dynamometers, but may be used for other types of force measurements such as the continuous weighing of material on a conveyor belt in conjunction with a recording pressure gage. The scale has numerous applications in determining forces where conventional scales are now used. This particular subject was chosen because of the need for a convenient, inexpensive, and accurate scale for use in measuring the force exerted by …

The Determination Of The Solubility Of Hafnium Oxide In Aqueous Solution By The Radioactive Tracer Technique, Hampden O. Banks

Masters Theses

"To date, there is no information in the open literature concerning the solubility of hafnium oxide in water other than the fact that it is very insoluble. This lack of experimental information is due, partly, to the fact that hafnium is a relatively new addition to the list of known elements"--Introduction, page 1.

A Study Of Cast Eutectic Structures By Means Of Optical And X-Ray Microscopy, John Stanton Winston

Masters Theses

"The present research is the result of interest in two rather broad, and at first thought, seemingly entirely separate topics: the structure of eutectics and x-ray microscopy. D. Hanson in 1923 in his correspondence with Albert M. Portevin in regard to his article on the structure of eutectics states, "A point that always stuck him (D. Hanson) in examining eutectics was that one of the constituents always formed a continuous phase round the other one. The orientation of one constituent was either constant or varied in a uniform manner. What, however, was the condition of the 'enveloped' constituent, which formed …

A Study Of Missouri Flint Clay, Edmond Preston Hyatt

Masters Theses

"The problem is one of attempting to explain the peculiar nature of Missouri Flint Clay and to expand the knowledge concerning it. Among the questions for which answers are sought are: What makes Missouri Flint Clay so hard? What happens to Missouri Flint Clay when it is ground? What is the mineralogical constitution of Missouri Flint clay?"--Introduction, The Problem, page 1.

A Determination Of The Economic Feasibility Of Producing Marginal Gas Wells, Horace Tharp Mann

Masters Theses

"The purpose of this investigation is to show that it is economically feasible to produce marginal gas wells in such a manner that all the gas from the edge of the field will be captured by the first row of wells. In this problem the permeability of the sand is to be variable but known, and the effects of this variable permeability on the pressure distribution, and resulting gas production, will be discussed.

In many gas fields the point at which it is generally considered unprofitable to drill new wells is well inside the boundary of the reservoir. This is …

Calculations Of Maximum Sag Of A Transmission Line With An Ice Load On One Span, Rodney A. Schaefer

Masters Theses

"An important problem concerning electric power lines is the calculation of the maximum sag occurring when there is an ice load on only one span. The object of this thesis is to determine a practical method for calculating the maximum sag of a transmission line, suspended on suspension insulators, with the aforementioned loading conditions. This paper is limited to the case where the supports of the transmission line are at equal elevations and all span lengths are equal"--Introduction, page 1.

The Economic Spacing Of Contraction Joints In Reinforced Concrete Pavements, Wilbert Frederick Wegener

Masters Theses

"Structurally, there are two types of joints used in concrete pavements: (a) the tied, or permanently-closed joint; and (b) the open or free type of joint. The permanently closed joint utilized tie-steel of some form to keep the joint from opening. Usually, this steel is in the form of short individual bars extending across the joint and bonded to both slabs (designated as "tie-bars") or in the form of distributed reinforcement. The remaining method of classification, that of refering [sic] to the joint purpose, gives the expansion joint, contraction joint, and warping joint. An expansion joint is, as the name …

The Theory Of The Specific Heat Of A Body Centered Cubic Lattice, Curtis Cleveland Webster

Masters Theses

"In normal crystalline solids the atoms are at rest in their lattice points at absolute zero of temperature. Increasing the temperature of the crystal increases the motion of the atoms about their lattice points. Approximately, each atom or ion may be treated as a harmonic oscillator. then from the equations of motion of the atoms, by the Born-von Karman theory of specific heats, the normal modes of vibration of the lattice can be expressed as the roots of a secular determinant. Application of this theory to determine the thermodynamic properties of crystals has resulted either in solutions that are inaccurate …