Digital Commons Network^™

Biofuel Gasification For Residential Heating, Bryan Duke, Courtney Mcintosh, Jeron Hogan

Mechanical Engineering

No abstract provided.

Autonomous Golf Cart Firmware, Gerik Kubiak

Computer Engineering

The Autonomous Golf Cart Project is a project sponsored by the Cal Poly Robotics Club. The multidisciplinary team is adding sensors and electronics to a regular golf cart with the goal to drive the golf cart around campus without and human input. This task requires a plethora of hardware and firmware to control that hardware. The firmware provides an interface for higher level software to then control the hardware and therefore drive the golf cart. This report is focused on the hardware modifications and the firmware used in order to drive the golf cart from a computer.

Electronic Deer Warning System, David Zhuo, Anlang Lu

Computer Engineering

Deer-vehicle collisions (DVCs) are extremely dangerous, often injuring or even killing drivers. Unfortunately, this form of automotive accident is commonplace in the United States. According to the NHTSA, DVCs result in 200 human deaths a year.2

Despite these deadly incidents, there currently are no deployed federal or state systems for preventing DVCs. There are many consumer electronic deer deterrent products, but their long-term effectiveness is questionable.3 In fact, there does not appear to be much research into electronic deer deterrent systems. Aside from constant audio output and electric shock, no other means of electronic deterrent exist. Even if fixed deterrents …

Power Distribution:Protection Analysis, Avneet S. Samra

Electrical Engineering

The objective of this project is to build a radial distribution system that operates on a lower voltage. The system consists of a transmission line protected by a SEL-351 Relay, a three- phase transformer protected by a SEL-587 Relay, and a three-phase induction motor protected by a Cooper Form 6 Controller. The SEL-351, SEL-587, and the Cooper Form 6 Controller are microprocessor-based relays that are used to provide protection under faulted conditions. When a fault is detected in the system, the closest upstream relay sends a trip signal to its assigned local breaker. The SEL-351 provides overcurrent protection for the …

Active Contact Lens - Low Power Backscattering Sensor-To-Antenna Integration Circuitry, Caleb B. Porter

Electrical Engineering

The Active Contact Lens measures the cornea-scleral radius of the wearer’s eye, which correlates to intraocular pressure (IOP), Glaucoma’s primary indicator. IOP varies throughout the day, and is drastically different from person to person, so constantly measuring it over a period of a few days can provide individualized tracking of the disease’s development and will help doctors develop personalized treatment schedules to treat the disease more precisely.

The Active Contact Lens sensor measures strain, based on the cornea-scleral radius, and reports the results wirelessly, to allow monitoring of an individual’s IOP over time. The lens is powered similarly to a …

Designing A Power Distribution System For The Arce 257 Revit Structural Model, Reid Wilhelm

Electrical Engineering

The construction industry needs engineers. Mechanical, electrical, and plumbing engineers, better known as MEPs, comprise a large number of employees who design and assist in the building of commercial structures. In particular, electrical engineers design power distribution systems for these buildings, including the power, lighting, low voltage, and fire protection subsystems.

Here at Cal Poly, architectural engineers enrolled in ARCE 257 create authentic structural plans for a fictitious two-story structure. This senior project transforms these structural plans into an architectural model and creates a power distribution system for the entire building. This is done through a building information modeling (BIM) …

3-Axis Automated Probe Traverse For Aerodynamic Testing, Tananant Boonya-Ananta, Ricky Wai, Zander Oostman, Teyvon Brooks

Mechanical Engineering

Our primary objective is to design, build, and test an automated traverse to hold measurement probes in Cal Poly’s low speed wind tunnel. The device should cause minimal flow disturbance. It’s movements must be able to cover eighty percent of the three-dimensional test section. The device should have a mounting point for interchangeable probes. The assembly is to be integrated with the current frame structure on the wind tunnel test section, and should allow very minimal deflection of the measurement probe. The user should be able to control the motion of the traverse via a computer interface which supports automatic …

Revolutionized Additive Manufacturing, Matthew Walker, Winthrop Townsend, Luca Fuller

Mechanical Engineering

No abstract provided.

Functional 3-D Cellulose And Nitrocellulose Paper-Based, Microfluidic Device Utilizing Elisa Technology For The Detection/Distinction Between Hemorrhagic And Ischemic Strokes, Alicia Leanne Holler

Master's Theses

The purpose of this thesis project is to demonstrate and evaluate an enzyme-linked immunosorbent assay (ELISA) on a paper microfluidic device platform. The integration of ELISA technology onto paper microfluidic chips allows for a quantitative detection of stroke biomarkers, such as glial fibrillary acidic protein (GFAP). Dye experiments were performed to confirm fluid connectivity throughout the 3D chips. Several chip and housing designs were fabricated to determine an optimal design for the microfluidic device. Once this design was finalized, development time testing was performed. The results confirmed that the paper microfluidic device could successfully route fluid throughout its channels at …

Compounding Fire Disturbance History Encourages Coast Redwood (Sequoia Sempervirens) Regeneration And Community Dominance, Matthew R. Brousil

Master's Theses

Disturbance is fundamental to forest ecosystem function and overall health, but climate change is likely to increase both disturbance frequency and intensity in the future. Forests subject to increasingly frequent and intense disturbances are more likely to experience compounding disturbance effects. Compounding disturbances may exert unpredicted, non-additive stresses on ecosystems, leading to novel conditions that may exceed the capacity for local species to survive and regenerate. I further hypothesize that compounding disturbances could create conditions misaligned with species’ adaptations by altering physical and chemical growing conditions in forest soils, affecting forest composition, structure, and, subsequently, function for many years following …

Fiber Glass Mat Splice Automation, Max Weinstein, Charles Scott Forbes, Max Kilpatrick

Mechanical Engineering

Currently, GAF has two operators manually splice together each roll of fiberglass mat. To save money and resources, GAF wants to automate this splicing process. Our team is responsible for stage 3 of 5 in this automation process. We are responsible for ensuring that the system is able to move autonomously to the necessary positions required for splicing together the rolls of fiberglass mat. We have determined the best solution for accomplishing this movement is to use linear slide actuators. This document will describe the process by which we arrived at our solution, the details of our solution, and a …

Compression Molded Composite Component, Greg Hermansen, Larsson Johnson, Joanne Medrano, Kyle Hammell

Mechanical Engineering

The following final design report outlines the design and fabrication of a carbon fiber compression molded sunglasses case. It intends to guide the development of a future lab activity for a composites undergraduate course at Cal Poly – San Luis Obispo. The activity aims to support an educational investigation in "out-of-autoclave" composites manufacturing methods, such as compression molding, which offer some key benefits over autoclave molding. The methodology behind the creation of a conceptual design, an initial prototype, and a final product is laid out in detail below.

Cal Poly Microgrid - Solar Panel Mounts, Dylan Mayer, Christian Odegard, Gregory Pellegrino, Connor Mckay

Mechanical Engineering

No abstract provided.

Chumash Heritage National Marine Sanctuary Sacred Waters Film, Cory B. Jones

Communication Studies

The debate to designate a National Marine Sanctuary off the Central Coast of California has been alive for nearly 30 years.

With a recent move by the National Oceanic and Atmospheric Administration (NOAA) to nominate the stretch of water as a sanctuary the issue has become one of great concern to local stakeholders.

With concern for additional bureaucracy and regulation that could negatively impact the local economy people choose to stand in opposition. Yet many that are concerned for the future of the region's waters want the protections from offshore oil drilling and other harmful practices that a Sanctuary would …

The Mustang Sculpture, Natalie Gibbons, Jordan Gates

Architectural Engineering

No abstract provided.

Long Beach Remodel, John Hinrichs

Architectural Engineering

No abstract provided.

Carpenters Apprenticeship Internship: Student And Industry Perspectives, Chris Falco

Construction Management

The Carpenters Apprenticeship Internship program is designed to provide students the opportunity to work as a construction laborer and get hands-on work experience. The goal of this study is to address the perceived benefits of the Carpenters Apprenticeship Internship with respect to the students, the industry members, and the union. In looking at the benefits this opportunity presents, any value that is aligned among the parties involved will be highlighted to convey the mutual advantages. Lastly, the demand among students for experience such as this will be assessed to see what the perceived value of labor experience is among students …

Feasibility Study Of Using Recyclable Polyethylene (Pet) Materials As Coarse Aggregate For Concrete Mixtures, Philip M. Angelo

Construction Management

The feasibility of using recyclable household plastics, specifically those made of polyethylene, commonly used in water and soda bottles, as a replacement for concrete coarse aggregate, was assessed. A method was developed for cutting polyethylene materials into fibrous strips. These strips were then used as a replacement for the rock coarse aggregate in batches of concrete. Standard 6” x 12” test cylinders were made using the concrete mixture and subject to destructive compressive testing in order to yield the compressive strength of the concrete mix 7, 14, 21, and 28 days after pouring. Three mixtures were tested, one control with …

A Case Study On Achieving 100% Customer Satisfactory Homes In Production Home Building, Garrett Whitlock

Construction Management

No abstract provided.

Using Video To Increase Awareness Of Inclusivity For Lgbtq+ Students On University Campuses: A Single-Site Case Study On Cal Poly, Mallory St. George

Journalism

This project is focused on the use of online video in creating awareness for LGBTQ+ inclusivity. In particular, it focuses on California Polytechnic State University San Luis Obispo, hereafter referred to simply as "Cal Poly," and the campus climate's effect on the LGBTQ+ student community. It aims to give a brief recap of Cal Poly's history in relation to its queer population, highlight the experiences of present-day students, assess what progress has been made, and provide a snapshot of the campus climate in 2016 to be used as a drawing point for future senior projects and evaluation of inclusivity progress. …

Social Media Marketing In The Film Industry: Using Social Media To Create A Successful Marketing Campaign For The Theatrical Release Of A Film, Katherine Baker

Journalism

This study analyzes the use of social media as a marketing tool within the film industry including its successes in regards to popular social tactics and campaigns as well as where it may fall short within the realm of marketing as a whole. As the world is racing to be the first to implement the “next biggest thing” and beginning to drift away from traditional marketing practices, social media is potentially the next step to ensuring a successful marketing campaign for any product or service. This study takes a look into how social media can best be used and implemented …

Using Relationship Theory To Improve Stem Outreach To Corporations: A Case Study For Starbase Los Alamitos, Mark Gibson

Journalism

The goal of this study was to improve corporate outreach efforts for an educational program called Starbase Los Alamitos. This Starbase program is part of a larger effort by the Department of Defense to improve STEM (science, technology, engineering, and mathematics) education in the United States.

This study was guided by the following research question: How can STEM programs use relationship management theory to improve corporate outreach? A review of the literature was performed and this study used relationship theory to design eight questions for a four person focus group. Control and treatment websites were identified. Participants were shown the …

Ios Application For Inventory In Small Retail Stores, Andrea Savage

Computer Science and Software Engineering

Currently, small retail stores with low technology budgets such as those right here in San Luis Obispo are struggling to integrate new technologies into their companies. This mobile application built for iOS with a Firebase backend is seeking to remove their barriers to entry. I built this application to give small retail stores a customizable application that allows them to display products electronically to customers and maintain accurate inventory both in one place. The construction of this application hinged around three major design decisions: UI design of the color management views, organization of the database, and accessing the database with …

Kihefo Vocational Center: Kabale, Uganda, Jason Matthew Angerer

Construction Management

Journeyman International (JI) is a non-profit organization which acts as a platform for bringing together volunteer Architects, Designers, Engineers, and Construction Managers with humanitarian projects around the world. Kigezi Healthcare Foundation (KIHEFO) a non-profit NGO located in Kabale, Uganda is a client seeking to build a vocational center to educate the workforce of Uganda. The center will include multi-purpose class rooms, a dining hall, rabbit farm, carpentry shop, and living complex. The Architect on the project was Courtney Wedel from Cal Poly. As the Construction Manager on the project my responsibilities include; Design Assist, Feasibility Analysis, Scheduling, Estimating, and Managing …

Photovoltaic Installation In Ecuador And The Amazon, David Mulder

Construction Management

The Photovoltaic Installation in Ecuador and The Amazon is part of a collaborative effort between two major construction clubs at Cal Poly: NECA and MCAA. Four students, two from each club, traveled with two faculty to install photovoltaics for two different communities. The first project was a solar installation to provide fresh water for the community of Santa Rosa. Project number two, was a sixteen-panel installation in Shell, Ecuador for the non-profit Reach Beyond. The main goals of each project were to provide fresh water, and achieve net zero electrical consumption.

Technology Adoption By California Central Coast Contractors, Nicholas A. English

Construction Management

Technology is trending in Construction, but it is unclear if smaller contractors have kept up with these trends like larger national companies have. This survey of San Luis Obispo County specialty and general contractors queried technology adoption, specific software use, estimator age, and opinions of various estimating attributes. It found that the majority of contractors use traditional estimating and quantity takeoff methods, the majority of contractors are 31 years old or older, and that local estimators value experience and knowledge as opposed to computer expertise. Local contractors recognize the value technology can provide, but have not adopted it in a …

Construction Of A Chicken Coop For Use By An Early Education Facility, Luke Cypress

Construction Management

There is a demand in the early education field for methods of exposing early learners to where our food comes from and how it’s produced. An excellent source of this exposure is commonly utilized in an onsite chicken-coop. These coops are in essence working farms, producing eggs and in some cases meat. While coops are not prohibitively expensive they often fall outside the scope of normal operating or educational budgets and can be difficult to fund. The purpose of this project was to identify a school that could use and benefit from a coop at no cost to the school. …

Managing Drip Filter Backflush Water, Charles M. Burt

BioResource and Agricultural Engineering

The paper discusses the principles of backflushing different types of filters, as well as pressure and flow requirements for proper backflushing of various filters. Additionally, it discusses options for what to do with the backflush water. A prototype ITRC design for cleaning and recycling backflush water is presented.

Impact Of Cross Section, Web Reinforcement And Load History On The Seismic Performance Of Slender Concrete Walls, Anahid A. Behrouzi

Architectural Engineering

Many reinforced concrete buildings in seismic regions employ reinforced concrete shear walls as part of the lateral force resisting system and these walls often have non-planar cross-sectional geometries. To date, the majority of experimental tests on slender concrete walls have been conducted on planar walls which have been subject to low shear stress demands. An experimental program was developed to examine the response of flanged C-shaped walls with respect of load history and a computational parametric study was conducted to focus more specifically on the impact of web reinforcement for walls subject to a range of shear stress demands.

The …

Academic Senate - Agenda, 11/29/2016, Academic Senate

Academic Senate Agendas

No abstract provided.