Digital Commons Network^™

Selective Depolymerization Of Industrial Hemp And Its Effects On Thermal Resistivity, Tanner J. Jolly

Materials Engineering

There is a growing shift within the construction materials industry towards green and sustainable building products. Spending in this area has increased 5 fold since 2011 to a total revenue of $70 billion. An area of particular interest has been aimed at replacing fiberglass batt insulation with cellulose. Cellulose is the most abundant polymer on earth, and has potential to replace petroleum derived insulations. This project explores the potential of selectively isolating cellulose by depolymerizing the support structures found in lignocellulosic materials – specifically lignin and hemicellulose. The current focus is on isolating cellulose from Cannibas sativa, but more …

Warren J. Baker Center For Science Building Review, John Pagliero

Fire Protection Engineering: Culminating Experience Project Reports

This report is a focused review and discussion of the life safety and fire protection design of Cal Poly Building 180: The Warren J. Baker Center for Science in partial fulfillment for the requirements of a Master’s of Science degree in Fire Protection Engineering at Cal Poly, San Luis Obispo. The report focuses on discussion areas specific to the curriculum of the Cal Poly Fire Protection Master’s program, including analysis of egress, structural fire protection, detection, alarm and automatic protection designs in comparison to current and effective codes and standards. This report also includes a, performance based, tenability analysis for …

Predicting Service Life Of 347 Stainless Steel Pipes By Carburization Rate Measurement, Tyler L. Sura

Materials Engineering

Chevron Corporation and other refiners face challenges predicting the service life of piping in coker furnaces. This is largely due to a build up coke on a single surface of the piping. This coke build up results in carbon penetration into the surface of the 347 stainless steel used for the pipes. Carbon penetration can lead to degradation of the surface and ultimately, the failure of the pipe. Current modeling software has difficulty predicting the influence of sulfur on the carbon penetration rate. This study aims to provide a baseline for further study into the subject. The carbon penetration rate …

Performing A Practical Paging Attack On The Lte Network, Nathan H. Yee

Computer Science and Software Engineering

No abstract provided.

Senior Project: Calendar, Jason L. Chin

Computer Science and Software Engineering

This calendar application is meant to help individuals with busy schedules. Those who must balance their time between working on multiple simultaneous projects would categorize key users. In the application, users will be able to participate in multiple projects at any one time. When a user is in a project, they will be able to create tasks, add tasks, be assigned to tasks, and add other users to the project. A key feature in this application is that each user is provided a personal project. In their personal project, any task assigned to the user from any project, will be …

Improvements For The T0c+ Geometry Of The Fast Interaction Trigger (Fit) Upgrade To Alice At The Cern Lhc, Noah Miller

Physics

The purpose of the ALICE experiment at CERN is to investigate the properties of the strongly interacting quark-gluon plasma formed in the high-energy collisions of lead nuclei in the CERN Large Hadron Collider. ALICE has been collecting data since 2009. The upcoming upgrade of the CERN LHC injectors during 2019-20 will boost the luminosity and the collision rate beyond the design parameters for several of the key ALICE detectors including the forward trigger detectors. The new Fast Interaction Trigger (FIT) will enable ALICE to discriminate beam-beam interactions with a 99% efficiency for the collisions generated by the LHC at a …

On-Sight Shifting At The Cryogenic Underground Observatory For Rare Events, Aaron C. Wong

Physics

During the summer of 2016, four Cal Poly students traveled to Assergi, Italy to contribute to the CUORE collaboration which is in search of a rare process called neutrinoless double beta decay. If detected, neutrinoless double beta decay will make break throughs in particle and nuclear physics, and will be the first observation of lepton number violation. The Cal Poly students provided on-sight shifting support during the installation phase of the project. This is a breakdown of the physics behind CUORE and Cal Poly's contribution.

Danalog: Digital Music Synthesizer, Evan R. Lew

Electrical Engineering

The Danalog is a 25 key portable digital music synthesizer that uses multiple synthesis methods and effects to generate sounds. Sound varieties included three synthesis methods including FM, subtractive, and sample-based, with up to eight adjustable parameters, at least four effects, including reverb, chorus, and flange, with five adjustable parameters, and at least two note polyphony, and a five band equalizer. The user would be able to adjust these effects using digital encoders and potentiometers and view the settings on two LCD screens.

The finals project was unable to meet the original design requirements. The FM synthesis method was primarily …

Data Fusion With 9 Degrees Of Freedom Inertial Measurement Unit To Determine Object’S Orientation, Long Dinh Tran

Electrical Engineering

Data fusion is a technique to integrate different types of data to a single unit to provide a more reliable representation of tracking measurement. Today, data fusion can be found in many applications such as tracking and surveillance system as well as on mobile applications. In this project, 9 Degrees of Freedom (DOF) Inertial Measurement Unit (IMU) composed of 3-axis Magnetometer, 3-axis Accelerometer, and 3-axis Gyroscope are processed to yield the object’s rotations in 3 dimensions. While the magnetometer (compass) is used to determine the heading angle, accelerometer is used to determine tilt axis, gyroscope can be process to calculate …

Roborodentia Robot (Duct Tape Craze), Tarrant J. Starck

Computer Science and Software Engineering

Roborodentia is an annual autonomous robotics competition held at Cal Poly in April. In 2017, Roborodentia was a head-to-head double elimination tournament with the winner being the robot that moves more rings onto the scoring pegs. For this year’s competition, I designed, built, programmed, and tested a robot.

Gridiron-Gurus Final Report: Fantasy Football Performance Prediction, Kyle Tanemura, Michael Li, Erica Dorn, Ryan Mckinney

Computer Science and Software Engineering

Gridiron Gurus is a desktop application that allows for the creation of custom AI profiles to help advise and compete against in a Fantasy Football setting. Our AI are capable of performing statistical prediction of players on both a season long and week to week basis giving them the ability to both draft and manage a fantasy football team throughout a season.

Soft Target For Advanced Emergency Braking System Daimler Trucks, Kurt C. Ebert, Kolter Knapp, Esgar Pulido

Mechanical Engineering

This report provides an overview of the AEBS Soft Target project delivered to Daimler Trucks North Amer- ica as part of the 2016-2017 Mechanical Engineering Senior Design class at California Polytechnic State University, San Luis Obispo. The purpose was to build a soft target to test Advanced Emergency Braking Systems, or AEBS, on Daimler 0 s large trucks. Though this design is for Daimler specifically, there may be other interested parties such as highway safety groups and rival auto manufacturers. Currently, there are no suitable alternative products that satisfy every requirement for Daimler to validate their systems. They require a …

Underwater Computer Vision - Fish Recognition, Spencer Chang, Austin Otto

Computer Engineering

The Underwater Computer Vision – Fish Recognition project includes the design and implementation of a device that can withstand staying underwater for a duration of time, take pictures of underwater creatures, such as fish, and be able to identify certain fish. The system is meant to be cheap to create, yet still able to process the images it takes and identify the objects in the pictures with some accuracy. The device can output its results to another device or an end user.

Multispectral Identification Array, Zachary D. Eagan

Computer Engineering

The Multispectral Identification Array is a device for taking full image spectroscopy data via the illumination of a subject with sixty-four unique spectra. The array combines images under the illumination spectra to produce an approximate reflectance graph for every pixel in a scene. Acquisition of an entire spectrum allows the array to differentiate objects based on surface material. Spectral graphs produced are highly approximate and should not be used to determine material properties, however the output is sufficiently consistent to allow differentiation and identification of previously sampled subjects. While not sufficiently advanced for use as a replacement to spectroscopy the …

Procedurally Generating Genetic Keys, Adam A. Levasseur

Computer Engineering

This project presents a method for creating multi-part models based on input keys to generate new, variant models via genetic algorithms. By utilizing 3D models as modular parts, this method allows for the generation of a unique, compound model based on one or multiple input keys. This paper explains the process of creating and testing such generation styles using simple geometry to create more complex, compound models.

Design And Proof Of Concept Of Parking Garage Capacity Network Using Distributed Ultrasonic Devices Interfaced With Mqtt Protocol, Justin M. Distaso, Erik C. Olsen

Computer Engineering

This paper overviews the Smart Structure project. We found a desire from the City of San Luis Obispo for a way to tell the availability of parking spaces in local parking garages. In addition to meeting this need the project aims to provide functionality and adaptability based on future “smart” devices and making the device fit into an Internet of Things (IoT) system. Currently drivers must manually navigate the parking garage to determine which floor has a parking spot. With our proposed solution drivers would be able to tell at a glance which floors had the most spots, as well …

Neural Network Ai For Fightingice, Alan D. Robison

Computer Engineering

Game AI in the fighting game genre, along the lines of Street Fighter, Mortal Kombat and Tekken, is traditionally script-based, with hard-coded reactions to various situations. Though this approach is often easy to understand and tweak, it requires substantial time and understanding of the game to implement in a way that is challenging and satisfying for the player due to the very large possibility space. This paper explores the use of neural networks as an alternative approach by implementing and training a network to select an action to take each frame based on the game state.

The Following Robot, Juan D. Cerda, Matthew S. Kwan, Vi M. Le

Computer Engineering

The objective of this project is to design, build, and test an autonomous robot with an associated Android application. The robot uses on board inertial measurement sensors (magnetometer, accelerometer, gyroscope) and coordinates itself through Bluetooth communication with the similar built­in measurement sensors on the Android phone to mimic and follow movement. The Following Robot incorporates the same basic movement functionality as a typical RC car. The robot follows the user’s phone through an application on one’s phone. This application accesses the phone’s accelerometer and gyroscope data and translates into appropriate conversions. Methods of tracking and calculating distance or angular displacement …

A Data-Driven Approach To Cubesat Health Monitoring, Serbinder Singh

Master's Theses

Spacecraft health monitoring is essential to ensure that a spacecraft is operating properly and has no anomalies that could jeopardize its mission. Many of the current methods of monitoring system health are difficult to use as the complexity of spacecraft increase, and are in many cases impractical on CubeSat satellites which have strict size and resource limitations. To overcome these problems, new data-driven techniques such as Inductive Monitoring System (IMS), use data mining and machine learning on archived system telemetry to create models that characterize nominal system behavior. The models that IMS creates are in the form of clusters that …

Complex Filters As Cascade Of Buffered Gingell Structures: Design From Band-Pass Constraints, Nicole M. Hay

Master's Theses

Complex filters are multi-input, multi-output networks designed to discriminate based upon the relative phase difference between input signals. Complex filters find application in modern wireless systems for single sideband transmission and image-reject reception. This thesis presents one active complex filter implementation using two operational amplifiers per stage, termed “type-II” topology. The “type-II” originates from the passive RC-CR polyphase topology presented by Gingell in his 1973 paper, “Single sideband modulation using sequence asymmetric polyphase networks.” This new topology gains several advantages over existing complex filter implementations, namely “cascadability” (multiple sections placed in series to create a higher-order response) without altering the …

A Modified Boost Converter With Reduced Input Current Ripple, Nathan H. Lentz

Master's Theses

Battery-powered trends in consumer electronics, transportation, and renewable energy sectors increase demands on DC/DC converter technology. Higher switching frequency and efficiency reduces solution size and cost, while increasing power capabilities. Still, switching noise remains the primary drawback associated with any DC/DC converter. Reducing a converter’s input ripple helps prevent switching noise from spreading to other systems on a shared DC power bus. This thesis covers the analysis, simulation, and implementation of a recently-proposed boost converter topology, alongside an equivalent standard boost converter, operating in steady-state, continuous conduction mode. A Matlab-based simulation predicts each converter’s input ripple performance using a state-space …

Modeling And Charging Control Of A Lithium Ion Battery System For Solar Panels, Garrett David Heinen

Master's Theses

The advancement in solar panel and battery technology makes them useful for energy supply and storage. This thesis involves the modeling and charging control of a lithium ion battery system for solar panels. The proposed model is based on the parameters and characteristics of a realistic battery and solar panel system; and the hybrid control approach combines the advantages of the adaptive incremental conductance method and the perturb and observe method to track the maximum power point of the solar panel for charging the battery unit. Computer simulation results demonstrate that this proposed approach offers a faster convergence rate than …

Hand (Motor) Movement Imagery Classification Of Eeg Using Takagi-Sugeno-Kang Fuzzy-Inference Neural Network, Rory Larson Donovan

Master's Theses

Approximately 20 million people in the United States suffer from irreversible nerve damage and would benefit from a neuroprosthetic device modulated by a Brain-Computer Interface (BCI). These devices restore independence by replacing peripheral nervous system functions such as peripheral control. Although there are currently devices under investigation, contemporary methods fail to offer adaptability and proper signal recognition for output devices. Human anatomical differences prevent the use of a fixed model system from providing consistent classification performance among various subjects. Furthermore, notoriously noisy signals such as Electroencephalography (EEG) require complex measures for signal detection. Therefore, there remains a tremendous need to …

A Geospatial Assessment Of Social Vulnerability To Sea-Level Rise In Coastal San Luis Obispo, Jesse A. Carpentier

Master's Theses

This project is an assessment of social vulnerability to sea-level rise in the unincorporated coastal area of the County of San Luis Obispo (County) using geospatial and statistical analysis. The intention of this assessment is to inform local climate adaptation efforts now required by state legislation. A social vulnerability index was generated at the Census block group level using 32 variables positively correlated with social vulnerability. The social vulnerability score for each block group is the sum of scores generated for the following principle components: (1) race/ethnicity and disability status, (2) social isolation and age, (3) income, and (4) housing …

On The Impact Of Android Api Evolution On Education Materials, Kennedy Owen

Master's Theses

The recent growing popularity of mobile devices has led to the establishment of several popular mobile platforms such as the Android operating system. To foster growth in this evolving market, Application Programming Interfaces (APIs) were created to enable developers to create mobile device applications that utilize mobile device features and functionality for personal or widespread commercial use. However, as a result of excessive device and API evolution, mobile development faces increasingly complex issues, including an alarmingly rapid decay of development resources.

This thesis conducts a case study around one such resource: a series of Android app development lab …

Linewidth And Ranging Characterization Of A Vernier-Tuned Distributed Bragg Reflector (Vt-Dbr) All-Semiconductor Tunable Swept Laser System For Lidar In Autonomous Applications, Taewan Kim

Master's Theses

ABSTRACT

Linewidth and Ranging Characterization of a Vernier-Tuned Distributed Bragg Reflector (VT-DBR) All-Semiconductor Tunable Swept Laser System for Lidar in Autonomous Applications

Taewan Kim

Linewidth and ranging experiments of a Insight packaged Vernier-Tuned Distributed Bragg Reflector (VT-DBR) laser across its wavelength output range of 1522.13 to 1566.18 nm is done in this work to characterize it for lidar applications. The purpose of this paper is to investigate the laser’s potential to combine the advantages of lidar and FMCW radar for autonomous systems.

Linewidth measurements were done by using a Mach-Zehnder interferometer to set up a delayed self-homodyne measurement. The laser …

The Population Genetics Of Morro Bay Eelgrass (Zostera Marina), Julia Gardner Harencar

Master's Theses

Seagrass populations are in decline worldwide. Zostera marina (eelgrass), one of California’s native seagrasses, is no exception to this trend. In the last 8 years, Morro Bay, California has lost 95% of its eelgrass. Eelgrass is an ecosystem engineer, providing important ecosystem services such as sediment stabilization, nutrient cycling, and nursery habitats for fish. The failure of recent restoration efforts necessitates a better understanding of the causes of eelgrass decline in this estuary. Previous research on eelgrass in California has demonstrated a link between population genetic diversity and eelgrass bed health, ecosystem functioning, and resilience to disturbance and extreme climatic …

Eulerian On Lagrangian Cloth Simulation, Kyle C. Piddington

Master's Theses

This thesis introduces a novel Eulerian-on-Lagrangian (EoL) approach for simulating cloth. This approach allows for the simulation of traditionally difficult cloth scenarios, such as draping and sliding cloth over sharp features like the edge of a table. A traditional Lagrangian approach models a cloth as a series of connected nodes. These nodes are free to move in 3d space, but have difficulty with sliding over hard edges. The cloth cannot always bend smoothly around these edges, as motion can only occur at existing nodes. An EoL approach adds additional flexibility to a Lagrangian approach by constructing special Eulerian on Lagrangian …

Investigation Of Peltier Devices For Refrigeration, Evan C. Drake

Physics

The purpose of our project was to characterize Peltier devices and determine if they were good candidates toward inexpensive off-grid solar powered refrigeration in poor countries. We measured the rate of cooling with a constant temperature thermal sink for different current inputs. Through numerous experiments we calculated the coefficient of performance for two different thermoelectric coolers (TECs) through a range of temperature differentials. In addition, we found the lowest temperature these Peltier chips could reach so that we could test the accuracy of the information provided by the manufacturers spec sheets. Overall the data gathered through our research is compelling …

Characterization Of Aquarefined Micro/Nanoporous Lead Material, Liam S. Russell, June Y. Suh

Materials Engineering

The process of aquarefining is an environmentally-friendly method for producing pure lead products that exhibit particularly low density. To observe the microstructures of these low-density forms of lead, scanning electron microscopy (SEM) was employed to examine aquarefined lead samples produced under three batches of processing conditions. Due to aquarefined lead's tendency to collapse under its own weight, careful measures were taken during transport and handling to avoid damaging the samples. Three types of microstructures were observed and correlated to changes in processing conditions: octahedron crystallites, microscales, and dendrites. Energy-dispersive x-ray spectrometry (EDS) was used to quantify the amount of oxygen …