Digital Commons Network^™

A Study Of The Non-Newtonian Turbulent Fluid Flow Through An Annulus, Yogesh R. Parikh

Masters Theses

"This investigation is concerned with the study of non-Newtonian flow through an annulus. The experimental analysis of incompressible non-Newtonian fluids in a long cylindrical annulus of radius ratio 0.375 was studied in the turbulent region. Different types of non-Newtonian fluids were used to procure flow behaviour for the annulus.
The effect of increasing flow rate of the non-Newtonian fluids was evaluated by gathering pressure drop data across the annulus using a differential manometer. The power-law model is used in this study to characterize the non-Newtonian flow. The parameters of the power-law model were evaluated by gathering viscometric data on a …

Optimization Of Flywheel Design For Internal Combustion Engines, Dady Jal Patel

Masters Theses

"A new approach to the problem of flywheel design has been developed, thus eliminating some of the problems of conventional design. The term flywheel design, in this thesis, refers to the determination of the flywheel inertia (mass moment of inertia) only. Two versatile computer programs were set up to obtain the flywheel inertia and the turning moment diagram for a large variety of internal combustion engines, and use was made of these programs to optimize the inertia of the flywheel with respect to speed. As an illustration the data of a 1960 Corvair engine were selected, and the results obtained …

Analysis And Discussion Of The Effect Of Heat Loss From The "Insulated" Face Of Thin Foil Heat Flux Meters, Mont Johnson Stevens

Theses and Dissertations

The object of this work was to investigate the effect that heat losses from the "insulated" face of thin foil heat flux meters has upon the sensitivity of heat flux meters. In the past it has been characteristic of any analysis done on heat flux meters to assume that the insulation on the back face of the foil was a perfect insulator and thereby neglect the effects of heat losses from this "insulated" face. It is hoped that the information given in this thesis will be of value in determining how the geometric and heat transfer parameters affect the operation …

Design Of Regeneratively Cooled, High Temperature, Clean Gas Plasma, Roger Carver Bartlett

Theses and Dissertations

The objective of this thesis was the design of a regeneratively cooled, high temperature, clean gas plasma generator facility. This facility was desired to extend the high temperature research capabilities of the Department of Mechanical Engineering.

An Experimental Investigation Of The Effect Of A Constant Body Force Field Upon The Drag Coefficient Of A Sphere, Brent Evans Boyack

Theses and Dissertations

The object of this thesis was to present the method and results of an experimental determination and correlation of the drag coefficients of accelerating spheres.

Opposed Disc Plough Furrows Hard Kimberley Soils, Department Of Agriculture, Western Australia

Journal of the Department of Agriculture, Western Australia, Series 4

THE work of reclaiming the eroded areas of the Ord River catchment has posed special problems for field staff of the Department of Agriculture engaged on this large scale project.

Thousands of miles of furrows must be contour-ploughed and seeded in extremely hard ground over big areas of eroded country.

A Rubber Membrane Analogy For The Study Of Shafts In Torsion., Myron D. Bruns

Masters Theses

"The thesis presents a review of literature giving reference to several books which present the many and varied methods of determining the shearing stresses in shafts. However, no reference was found that used a rubber membrane analogy similar to that used in th is thesis. The theory of torsion, the membrane theory, and its analogy have been presented for a better understanding of the subject. Illustrations are used freely for clarity.

Analytical methods and solutions are given for two problems. The first method is that of writing a Saint-Venant stress function and satisfying the necessary conditions for it to be …

Test 871: Oliver 1950 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 869: Oliver 1850 Diesel 4wd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 874: Oliver 1650, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 873: Oliver 1650 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 862: Minneapolis-Moline U302 (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 864: Wagner Fwd Wa4 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 868: Case 1200 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Forced Convection Heat Transfer Coefficients And Induction Heating, Max Edwin Light

Masters Theses

“The purpose of this study was to design and build an apparatus to experimentally determine the convective heat transfer coefficients for water flowing in a horizontal tube at turbulent flow. Also it was planned to use the apparatus to investigate the spatial dependence of energy deposition by induction heating.

An instrument and measuring techniques were developed that gave reasonable correlations between experimentally determined heat transfer coefficients and values calculated from generally accepted heat transfer relationships developed by other experimenters. Most of the calculated values were within ± 10% of the experimental values for a wide range of flow rates.

It …

The Effects Of Granular Size On The Thermal Conductivity Of Sand, Kanubhai M. Patel

Masters Theses

"The thermal conductivity of granular materials can be determined by the Thomas method. This method was used here to determine the effects of granular size on the thermal conductivity of sand. A river sand was secured and screened. The sand retained between the Tyler Standard Screen Scale, mesh 10 and 14, 14 and 28, 28 and 40, 40 and 48, 48 and 60, and below mesh 60, was used for tests.

The thermal conductivity for the above six samples obtained by the author coincide fairly well with published data.

It is reported in the International Critical Tables that the thermal …

The Design, Construction, And Evaluation Of A Vortex Stabilized Plasma Generator, Ronald Ray Williams

Masters Theses

“This report presents the design, construction, and evaluation of a vortex stabilized arc plasma generation facility operating on argon.

The facility consisted of five basic systems; the plasma genera- tor, the electrical power system, the argon flow system, the cooling system, and instrumentation.

The facility was designed to meet four general requirements; stable arc operation, low electrode deterioration, low cost of construction, and provisions for determination of the operating characteristics and thermal properties of the plasma.

Experimental results obtained in the laboratory agreed well with the design conditions. The rate of energy dissipated in the electric arc varied from 7. …

The Effect Of An Induction Field On Transducers., Ratilal S. Patel

Masters Theses

"This report presents the results of an experimental investigation on the effect of an induction field on transducer output. Various types of transducers; strain gages, thermocouples, and thermistors, were used. The changes in the output of these transducers were measured for various induction field conditions.

Measurements must often be made where strong electrical fields are present. Strain gages are used to measure the stresses in electrical machinery. Thermocouples and thermistors used for measuring the temperature of materials undergoing heat treatment with an induction heater are also subjected to an induction field.

The general experimental procedure was the same throughout the …

Investigation Of The Effect Of The Wall Thickness On The Residual Stresses Developed In Thick Wall Cylinders Due To Water Quenching From The Outside Surface., Ghanshyam Chandubhai Patel

Masters Theses

"This investigation has been made to determine the residual stresses in thick wall cylinders by the use of strain gages.

The cylinders were quenched from their outer surface i n water from a temperature of 1000°F, and the resulting residual stresses were determined by Sachs boring-out method. The effect of the wall thickness of the cylinders on the residual stresses and the error developed due to the boring operation were discussed"--Abstract, p. ii

The Effect Of Surface Roughness, Cure Pressure, And Temperature Level On The Thermal Resistance Of Bonds And Contacts, David Leo Schwaller

Masters Theses

"This investigation was conducted to determine the thermal effect of temperature level, surface roughness, and curing pressure on bars and bonded interfaces.

The equipment used in this investigation is shown in Fig. 1 and Fig. 2. The four specimens used, cylindrical aluminum alloy bars, were cut radially at their midpoints and faced on a lathe. Heat was supplied by an electrical resistance heating element and an ice bath was used to conduct heat from the alloy specimen. A heat shield was used to insure one dimensional heat flow. Spacers were placed in the insulation at the top, the interface, and …

The Effects Of Granular Size On The Thermal Conductivity Of Fine Sand, Fikri Yalvac

Masters Theses

"The Thomas method (1) for determining the thermal conductivity of solid materials can be used for the determination of the thermal conductivity of granular materials. In this thesis this method has been used to determine the effect of the granular size of sand cn its thermal conductivity.

River sand was classified according to size by the Tyler Standard Screen Scale into 50-60, 50-80, 80-100, 100-200, and below 200 mesh size. These sands were used for the experiments. The clay was separated from these samples to obtain pure river sand for the experiments.

According to the International Critical Tables, the thermal …

Test 870: Oliver 1850 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 872: Oliver 1950 Diesel 4wd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 875: Oliver 1850, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 876: Oliver 1850 4wd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 863: Minneapolis-Moline U302 (Lpg), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 865: Case 750 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 866: Zetor 2011 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 867: Zetor 4011 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Generalized Programs For Heat Transfer Analysis., Ceylung Chu

Masters Theses

"This report presents numerical methods for calculating temperature distributions in any physical system in which heat transfer is taking place. The syste.11 may be at either a steadystate condition or a transient condition. The temperature distribution may itself be or primary interest, or it may be used further to calculate the flow or heat or thermal stress.

The system under investigation is divided into a certain number of subdivisions, or so-called "regions". A reference point (node point) will be taken as representative for the region which includes that point. The temperature at the "node point11 is taken to be the …