Digital Commons Network^™

Sustainable Cow Dung Bricks: An Innovative Approach To Eco-Friendly Masonry With Enhanced Thermal And Mechanical Performance, Nagesh Sugandhi, Sachin Patil, Satish Reddy, Ashwini G, Santosh Kumar

Journal of Sustainable Construction Materials and Technologies

This study explores the development, characterization, and performance of sustainable cow dung bricks using locally sourced organic (cow dung) and mineral (clay, quartz sand, feldspar, lime) constituents for non-load-bearing masonry in India. Three blends with varying cow dung content (70%, 75%, 80%) were mixed, molded, air dried, and cured without kiln firing to reduce environmental impact. The bricks' mechanical properties—compressive strength, water absorption, bulk density, flexural strength, shore hardness, and modulus of elasticity—were systematically evaluated with complete statistical documentation (n = 6 replicates per formulation per test age). Microstructural features were investigated using Fourier Transform Infrared Spectroscopy (FTIR) and X-Ray …

Optimizing Warranty Policies For Remanufactured Products: When Should They Be Longer, Shorter, Or Identical To New Product Warranties?, Kunpeng Li, Jun-Yeon Lee

Faculty Publications

Manufacturers adopt different warranty strategies for remanufactured products, offering shorter, identical, or longer warranty periods compared to new products. However, prior research has only focused on manufacturers offering either shorter or identical warranties. In addition, the existing literature has not captured the diminishing returns of warranties, i.e., as the warranty coverage increases, its incremental benefits begin to decrease but the costs continue to increase. To address these gaps, we develop an optimization model that jointly considers pricing and warranty decisions while accounting for warranty’s diminishing effect on consumer’s willingness to pay for remanufactured products. We show that all three observed …

Sustainable Cement-Blast Furnace Slag Mortar, Richa Jain, Harshit Jain, Ashish Nim

Journal of Sustainable Construction Materials and Technologies

New building materials that required and produced less energy are need of today's infrastructure development. The ability of such building materials to promote sustainable development always puts its demand in active mode. With huge consumption of naturally occurring materials in building construction, the problem related to environment degradation is now common for world. Along with this, world is also facing the problem of reuse, recover and scientifically approved disposal of non-biodegradable wastes. Blast furnace slag (BFS) is one of those steel industry wastes that are abundantly available and their disposal arises as prime challenge for industries. This research work makes …

Identification Of Thruster Faults In Underwater Vehicles By Using Custom Encodings In Spiking Neural Networks, Donovan Gegg

LSU Master's Theses

Autonomous Underwater Vehicles (AUVs) are untethered robotic platforms used for tasks such as seafloor mapping, infrastructure inspection, and environmental monitoring. Recent technological advances have produced smaller, more affordable platforms, broadening access to research teams and small companies alike. This miniaturization comes at the cost of them handling drawbacks associated with a more compact machine such as reduced battery capacity as well as limited processing and sensing capabilities. These constraints make small-sized marine vehicle’s reliability critical as they can cause malfunctions, making the loss of a vehicle more likely. Actuator faults are particularly consequential as unintended and unstable control in an …

Experimental Study Of Dimpled Serpentine Reactors For Hydrogen Production Via Methanol Steam Reforming, Mohamed I. Zeid, Mahmoud A. Shouman, Osama Abdelrehim, Ahmed M. Hamed

Mansoura Engineering Journal

Hydrogen is widely regarded as a clean energy carrier, with methanol steam reforming (MSR) emerging as a promising route for portable and on-board applications due to its favorable operating conditions and high hydrogen yield. Reactor geometry plays a decisive role in hydrogen productivity, pressure drop, and energy efficiency, yet the balance among these factors remains insufficiently addressed. In this study, three serpentine aluminum microreactors: a plain serpentine reactor (PSR), a rhombusdimple reactor (RDR), and a hemispherical-dimple reactor (HDR) were fabricated and coated with a copper (II) oxide, zinc oxide, aluminum oxide (CuO/ZnO/Al₂O₃) catalyst to experimentally investigate the effect of dimple …

Task-Based Analysis Of Augmented Reality In Collaborative Robotic Programming For Manufacturing Assembly, Medhavi Kamran, Snehesh Shrestha, Vinh Nguyen

Michigan Tech Publications

Augmented Reality (AR) is often promoted as a solution to the cognitive and physical demands of traditional Teach Pendant (TP) programming for collaborative robots. Although prior work has suggested advantages of the AR interface, many evaluations have been limited in scope and may not fully represent the complexities of real-world manufacturing tasks. This study compares the performance of an AR interface to that of a standard TP interface for manufacturing assembly tasks of varying difficulty. In a between-groups study, one group of operators completed standardized assembly tasks using the TP interface, while a separate group used the AR interface instead. …

Layer-Wise Printing Parameter Optimization For Laser Powder Bed Fusion, Chaoran Dou, Rongxuan Wang, Raghav Gnanasambandam, Jianzhi Li, Zhenyu James Kong

Manufacturing & Industrial Engineering Faculty Publications

Additive manufacturing (AM) is a transformative technology that enables the fabrication of complex geometries layer by layer. However, metal parts produced via AM processes such as laser powder bed fusion (LPBF) are prone to various defects, including porosity and deformation. These defects often result from suboptimal printing parameter settings. Traditional approaches typically aim to reduce defects by optimizing a fixed set of parameters for the entire part. However, such methods do not account for layer-wise variations in printing conditions caused by changes in geometry, heat transfer, and re-heating effects. While optimizing parameters for each layer could improve part quality, it …

Impact Of Glass Powder As A Sustainable Material On The Workability, Strength, And Durability Properties In High-Performance Basalt Fiber Reinforced Concrete: A Statistical Analysis, Ahmed Fathi Mohamed Salih

Journal of Sustainable Construction Materials and Technologies

The global construction sector is increasingly challenged to balance environmental sustainability with the growing demand for durable, high-performance materials. As cement production continues to be a major source of anthropogenic CO2 emissions, the incorporation of alternative, low-impact binders has become a key strategy for reducing the environmental footprint of concrete. In this context, glass powder (GP)—a finely ground industrial by-product rich in amorphous silica—has emerged as a promising partial replacement for Portland cement. Its pozzolanic reactivity contributes to improved hydration and matrix densification, while its use also supports circular economy principles by diverting waste glass from landfills. At the same …

Roadmap: Integrating Artificial Intelligence In Structural Health Monitoring Systems, Simon Laflamme, Erik Blasch, Flippo Ubertini, Zheng Liu, John Wertz, Christine Knott, Matthew Cherry, Eric Lindgren, Fu-Kuo Chang, Amrita Kumar, Jack Poole, Keith Worden, Austin Downey, Jie Wei, Patrick F. Musgrave, Adrian S. Wong, Guiseppe Quaranta, Marco Martino Rosso, Giuseppe Carlo Marano, Yu Chen, Et. Al.

Faculty Publications

Advances in computing and machine learning (ML) methods have led to a rapid rise in artificial intelligence (AI) research and applications in many fields. AI research benefitted from advances in computation hardware, collection and distribution of large data sets, and proliferation of software techniques. AI techniques include ML for provable results, deep learning for data exploration, reinforcement learning for control, and active learning for adaptive systems. Likewise, AI algorithms can handle large amounts of data, construct unknown representations, and provide a direct link between data and classification for decision making. These unmatched capabilities have been seen as a path to …

An Ambient Acoustic Ice-Fracturing Dataset Taken In Shallow Freshwater, John Case, Andrew Barnard, Daniel Brown

Michigan Tech Publications

This paper describes an acoustic dataset collected on a frozen shallow freshwater lake between February and March of 2024. This collection took place over one full week on Portage Lake in the Upper Peninsula of Michigan, USA. The first sub-dataset consists of ambient ice and environmental noises collected by an array of hydrophones, microphones and geophones placed below, above and on the ice respectively. The second sub-dataset consists of instrumented force hammer impacts at a series of locations on the the ice with the corresponding response at each acoustic sensor. All acoustic data were recorded at a sample rate f …

Lightweight And Resilient Cryptographic Protocols For Next-Generation Networking Systems, Saif Eddine Nouma

USF Tampa Graduate Theses and Dissertations

The security of our increasingly interconnected world is strongly dependent on the strength and practicality of the cryptographic tools we deploy. As billions of embedded devices join the Internet of Things (IoT) and interact with remote cloud infrastructures for data processing, analysis, and actuation, they evolve into so-called digital twins. This rapid expansion introduces numerous attack vectors, particularly targeting constrained IoT devices, which greatly increase the attack surface and often become the root cause of large-scale infrastructure compromises. At the same time, the rise of quantum computing threatens the hardness of today’s intractability assumptions that underpin cryptographic primitives currently deployed. …

Towards Sustainable Energy Storage: Evaluating The Performance Of Three Polymer Electrolytes For Zinc-Ion Batteries, Roya Rajabi, Shichen Sun, Buke Wu, Jamil A. Khan, Kevin Huang

Faculty Publications

Polymer electrolytes have been explored as an alternative to conventional aqueous electrolytes in zinc-ion batteries, particularly for flexible and wearable applications. Despite the increasing interest in polymer electrolyte-based zinc-ion batteries (ZIBs), their development is still in its early stages due to various challenges. In this study, we investigated three promising polymer electrolytes: CSAM (carboxyl methyl chitosan with acrylamide monomer), PAM (polyacrylamide monomer hydrogel electrolyte), and p-PBI (phosphate-doped polybenzimidazole solid electrolyte) with Zn(ClO4)2 and Zn(OTf)2, as electrolytes for zinc-ion batteries. The p-PBI solid electrolyte showed high mechanical stability and improved resistance to short-circuiting during cycling. The presence of carboxyl groups in …

Towards Sustainable Energy Storage: Evaluating The Performance Of Three Polymer Electrolytes For Zinc-Ion Batteries, Roya Rajabi, Shichen Sun, Buke Sun, Jamil A. Khan, Kevin Huang

Faculty Publications

Polymer electrolytes have been explored as an alternative to conventional aqueous electrolytes in zinc-ion batteries, particularly for flexible and wearable applications. Despite the increasing interest in polymer electrolyte-based zinc-ion batteries (ZIBs), their development is still in its early stages due to various challenges. In this study, we investigated three promising polymer electrolytes: CSAM (carboxyl methyl chitosan with acrylamide monomer), PAM (polyacrylamide monomer hydrogel electrolyte), and p-PBI (phosphate-doped polybenzimidazole solid electrolyte) with Zn(ClO₄)₂ and Zn(OTf)₂, as electrolytes for zinc-ion batteries. The p-PBI solid electrolyte showed high mechanical stability and improved resistance to short-circuiting during cycling. The …

Reinforcement Learning For Imbalanced Data In Robotic Anomaly Detection Within Autonomous Manufacturing, Salma Messaoudi, Ahmed Bendaouia, El Hassan Abdelwahed, Mohammed Ameksa, Hajar Mousannif, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

Ensuring reliable anomaly detection in industrial robots is critical for safe and autonomous manufacturing operations. However, it remains challenging due to temporal dependencies and class imbalance in sensor data. This study presents a reinforcement learning approach using Deep Q-Network (DQN) enhanced with Long Short-Term Memory (LSTM) and Gradient Boosting Machine (GBM) for robust anomaly detection in robotic systems. The proposed framework integrates an LSTM into the DQN policy to capture temporal patterns. It also introduces a novel GBM-based reward mechanism that mitigates class imbalance by applying SMOTE (Synthetic Minority Over-sampling Technique) after removing temporal dependencies. Experimental results demonstrate that this …

Decentralized Q-Learning Supervisory Control For Coordinated Multi-Loop Tuning In Pump Stations, David Brattley, Wayne Weaver

Michigan Tech Publications

This paper introduces a reinforced learning-based supervisory control architecture that oversees multiple Recursive Least Squares (RLS) based self-tuning pump controllers and determines when each loop is permitted to adapt its gains. The supervisor learns adaptation policies that minimize interaction between loops while preserving responsiveness to changing hydraulic conditions. A two-loop pump station simulation is used to evaluate performance under product changes and transient flow disturbances. The results show that the supervisory layer reduces the number of simultaneous adaptation events by over 70%, leading to a 32% lower pressure-tracking error and 45% fewer gain-induced oscillations compared to conventional independent adaptive control. …

Supporting Data For Novel Approach For Quantifying The Impact Of Coherent Structures On The Turbulent Kinetic Energy Decay Rate, Tim Berk, Ankit Gautam

Browse all Datasets

This project investigates the influence of coherent structures on the decay of turbulent kinetic energy (TKE). The work was conducted as part of the PhD research in Mechanical Engineering by Ankit Gautam at Utah State University.

Multimodal Thermal And Mechanical Characterization Of Cryopreservation Effects In Biological Cells, Subhrajyoti Sourav Kumar Kundu

LSU Master's Theses

Cryopreservation is critical for long-term storage of cells, tissues, organs, and reproductive cells in medicine, biotechnology, and conservation. However, its success is limited by ice formation and cryoinjury, prompting extensive research into analytical tools for understanding and improving cryopreservation outcomes. We outline the principles of each technique and how they are used to detect key thermal and physical events such as ice nucleation, vitrification, devitrification, and cryoinjury. DSC enables quantitative thermal characterization including critical cooling/warming rates (ranging from 1-200°C/min for various systems) and glass transition temperatures. Cryomicroscopy provides direct real time visualization of ice crystal dynamics, distinguishing intracellular versus extracellular …

Thermal Management And Lubrication Characteristics Of Tungsten Disulfide (Ws2) Vegetable-Based Nanolubricants, Jaime Taha-Tijerina, Dyana De Leon-Elizondo, Jade Mendieta, Leonardo Taha-Soto

Informatics and Engineering Systems Faculty Publications

Recent innovations with the aid of nanotechnology are more frequently seen in the industrial sectors. Lubricants are a high-end commodity resource used in many manufacturing processes; unfortunately, most of these lubricants are petroleum-based, which come with certain drawbacks, such as environmental aspects, handling issues and high costs. With the incorporation of nanostructures within fluids and lubricants, novel material alternatives are replacing conventional lubrication systems, maintaining the required thermophysical and tribological characteristics. This research provides an analysis of vegetable lubricant, castor oil (CO), and the effects of the incorporation of WS2 nanofiller at diverse filler fractions. A TEMPOS thermal analyzer device …

Acoustic Levitation At Sub-Atmospheric Pressures And Reduced Temperatures: An Approach To Study Ice Crystal And Hypersonic Shockwave Interaction, Imteaz Osmani, David J. Delene, Hallie Boyer Chelmo

Graduate Research Achievement Day Posters

Micrometer-sized atmospheric ice crystals are commonly observed in high-altitude clouds. Inside clouds, they attach in different orientations, producing varied geometries, yet their formation mechanisms remain poorly understood. Their behavior under shock wave conditions remains underexplored due to lack of laboratory techniques capable of producing atmospherically realistic ice in controlled conditions. No experimental data and laboratory techniques exist to date on the interaction between atmospheric ice crystal aggregates and hypersonic shockwaves. To explore realistic atmospheric ice crystals’ thermodynamic and mechanical changes in hypersonic environments, we investigate the formation and behavior of ice crystal aggregates using acoustic levitation that avoids physical contact …

Influence Of Pulse Width On Energy Deposition And Temperature In Nanosecond-Pulsed Discharges, Christopher B. Reuter, Joshua B. Sinrud, Tanvir I. Farouk, Nicholas S. Dewey, Dmitri Kaganovich

Faculty Publications

Nanosecond-pulsed discharges are a promising method to enhance combustion but can generate significant levels of electromagnetic interference (EMI). Modifying the discharge pulse width is an unexplored option to reduce EMI, but few studies have examined how changing the pulse width affects discharge parameters such as energy and temperature. This study addresses this issue by systematically investigating how the pulse width affects the energy per pulse, breakdown time, rotational temperature, and vibrational temperature in air across different frequencies, flow velocities, and gap distances in a plasma-assisted flow tube. It is observed that the pulse width has a substantial impact on the …

Investigation Of Material Properties Of Thermoplastic And Thermoset Polymer Materials At Cryogenic Temperatures Using Molecular Dynamics, Swapnil S. Bamane, Sagar Patil, Khatereh Kashmari, Benjamin D. Jensen, Brett A. Bednarcyk, Evan J. Pineda, Jeffery Hinkley, Ozgur Keles, Jin Ho Kang, Gregory Odegard

Michigan Tech Publications

Cryogenic fluids, such as liquid hydrogen and liquid oxygen, are critical for space operations as rocket fuel and life support. The fluids need to be contained in tanks that can withstand the effects of cyclic thermal and pressure loading throughout their lifecycle. Polymer matrix composites (PMCs) are prime candidates for these tanks because of their low mass, which is important for fuel savings. Although advanced PMC systems have been developed for a wide range of engineering applications, insight is still needed to identify optimal polymer matrix materials for cryogenic structural applications. The objective of this study is to use molecular …

Portable Ice Cube Maker, Ayden Ziegler, Emiliano Hansen, Wyatt Engdahl, Dane Hansen

Mechanical Engineering

This Final Design Report outlines the senior design project undertaken by a team of mechanical engineering students at California Polytechnic State University, San Luis Obispo, for the development of a portable backpacking ice cube maker. The project aims to design, build, and test a lightweight, compact device that produces ice cubes for backpackers in remote outdoor environments. The goal is to create a functional prototype that is durable, user-friendly, and suitable for backcountry use. This document details background research, project objectives, and project plan, and current design status.

Pollinators Exhibit For Paso Robles Children’S Museum, Isabelle Moll, Matthew Moore, Joseph Hovanesian, Evan Stock, Matthew Wiecking

Mechanical Engineering

This report documents the design and development of an interactive pollination exhibit created for the Paso Robles Children’s Museum as part of the Mechanical Engineering Senior Project program. The goal of the project was to design a durable, safe, and engaging educational exhibit that introduces children to the role of pollinators in local ecosystems and agriculture through hands-on play. The final design features a triple-track system with rolling bee elements and a central pollen ball pathway that demonstrates how pollinators move between flowers and return resources to the hive. The exhibit incorporates visual feedback and locally inspired design elements to …

Baja Sae Gear Testing, Selina Bayles, Lucia Giacalone, Claire Cornelsen, Sarah Talbert

Mechanical Engineering

The Baja SAE Gear Testing project outlined a test stand and procedure to update the S-N curve currently used by the Baja SAE team. Currently the Cal Poly Baja SAE geartrain team uses a S-N curve to design custom gears, but this S-N curve does not accurately reflect the gears uses and their fatigue life. This project outlines the exploration of a dyno set up to allow for future testing of different categories of short life cycle gears to collect data and generate a new S-N curve and, ultimately, update the design of the gears. This team created a dyno …

Cathy's Trike, Jameson Stengel, Victor Robles, Asher Becker

Mechanical Engineering

Cathy Hoenig needs a better way to safely steer her trike since she recently had her arm amputated at the elbow. Right now, the standard steering setup doesn’t work for her because it’s designed for someone with two arms. The main issue is that because she can't hold the steering bar with both hands, she loses control and stability while riding, which takes away from her freedom and independence. We’re looking to design some kind of support or adaptive steering system that’ll let her feel safe and confident on her trike again. Our goal is to create a solution that …

Bonderson Workbench, Han Xu, Aidan Robleto, Sean Murphy, Victor Duran

Mechanical Engineering

This project redesigns the existing creative workbenches in Cal Poly's Bonderson High Bay to improve mobility and functionality for students and staff in the Mechanical Engineering Department.

Fsae Bespoke Brake Calipers For Hub Motor Architecture, Connor William Vaughan, Liam Upton Walsh, Bradley Brian Kern

Mechanical Engineering

Brakes are the most critical safety system on any performance vehicle, and as Cal Poly Racing transitions their Formula SAE car from a single rear motor to a four-in-wheel motor setup with regenerative braking, the team identified an opportunity to develop a bespoke brake caliper tailored to their specific needs. This document outlines the research, design, manufacturing, and validation of custom front brake calipers designed to improve upon commercial motorcycle calipers in key areas such as serviceability, mounting rigidity, thermal behavior, mass, and hub motor integration. The resulting design is a two-piece, four-piston, radially-mounted aluminum caliper featuring titanium pistons, toolless …

Cvj Torque Loss Dynamometer, Malaika Sriram, Coleman Brown, Zachary Norris, Logan Mast, Chris Mattis

Mechanical Engineering

This report details the design and results of a dynamometer testing rig built to measure torque losses in constant velocity joints (CVJs) for Cal Poly Racing's Baja SAE team. The rig spins a flywheel connected to articulable CVJs up to 800 RPM using a motor, then decouples it and measures the spin-down rate from 800 to 100 RPM to calculate angular acceleration and torque loss. The data collected from this dyno will be used to inform freewheel packaging for future Baja car development.

Design And Development Of A 12-Degree-Of-Freedom Quadruped Robot, Kai De La Cruz

Master's Theses

This thesis presents the design, analysis, and experimental validation of a 12-degree-of-freedom (DOF) quadruped robot developed as a research platform for legged locomotion and control. The system builds upon the Cal Poly Legged Robotics Group’s prior 8-DOF quadruped, addressing key limitations in manipulability, load distribution, and mechanical robustness by introducing a 3-DOF leg architecture.

The mechanical design emphasizes lightweight construction, structural integrity, and modularity to support future research extensions. Static and dynamic loading models were developed to inform component sizing and material selection. A carbon-fiber chassis and redesigned leg assemblies were fabricated and validated through finite element analysis and physical …

Development Of An Automated Platform For Cell Biology Experiments, Dipendra Nepal

Shelby Hall Graduate Research Forum Posters

Cell biology experiments involve repetitive tasks such as pipetting, sample preparation, and imaging, which are typically performed manually. These manual processes can introduce variability, reduce efficiency, and increase the cost of biomedical research. To address these challenges, our lab is developing a modular robotic platform, iEye™, to automate key steps in cell biology workflows [1]. The system is designed as self-contained modules, allowing flexible development and integration of different functionalities. In this work, we focus on a sample preparation module that integrates a 6-degree-of-freedom robotic arm, a motorized stage, and a pneumatic pipetter. This module is being developed to automate …