Digital Commons Network^™

An Investigation Of High Strength To Weight Corrugated Compression Panels With Non-Load Carrying Webs, Charles Thomas Lee Mills

Mechanical & Aerospace Engineering Theses & Dissertations

An investigation of the weight saving potential of corrugated compression panel concepts using curved elements and non-load carrying webs was performed. The concepts investigated were corrugated panels with flat and curved caps with beaded webs. These concepts utilize a beaded web that carries negligible axial load but is very stiff in the transverse direction. Therefore the web substantially stabilizes the load carrying caps to produce a high weight-strength efficient structure.

The optimum geometry parameters were determined using an iterative solution method employing simplified buckling assumptions. The results were checked with a non-linear optimization program coupled to a rigorous buckling analysis. …

A Non-Linear Vortex Panel Method For Wings With Edge Separation, Vijay Kalburgi

Mechanical & Aerospace Engineering Theses & Dissertations

A global nodal vortex panel method is developed to predict steady aerodynamic loads on rectangular lifting surfaces with side edge separation. The lifting surface and free shear layers are modeled by bound and free vortex sheets respectively, which are then discretized into triangular bound and free vortex panels respectively. On each triangular panel, a linear distribution of vorticity is defined in terms of the global components of vorticity at its nodes. The velocity field induced by any triangular vortex panel is obtained in closed form. The vortex core of the side edge vortex is modeled by a concentrated core of …

Computational Method For Solving The Kinematics Of Mechanisms Using Matrix Methods, Rajat Pardal

Theses

This thesis deals with the computational methods for kinematics of mechanisms using matrix methods. The method is particularly suited to the complex mechanism problems for which hand calculations are difficult. The thesis first reviews the matrix methods on which the program IMP is based. A computer program developed by Ve Tung using the same theory is enhanced in this thesis. By using this revised program, comparison between the non-linear algebraic approach and the matrix methods developed in this thesis has been made by the help of suitable examples. Further, it has been proved that the Integrated Mechanisms Program does not …

Optimum Design Of Structures Subject To Buckling Constraints, Thomas G. Looby

Theses

This thesis describes the optimal design of bar type planar truss structures subject to stress and buckling constraints. All of the structures considered are modeled using the direct stiffness finite element approach. A mathematical programming method incorporating a feasible directions routine is utilized to develop least weight designs for these conditions. The existing structural optimization programme CADOS which has successfully solved stress and deflection problems for this class of structures is adapted herein to treat local stability constraints based on Euler bucking criteria.In addition the optimization routine is modified to more effectively treat, infeasible starting designs. These modifications were tested …

Finite Element Analysis Of The Prosthetic Acetabular Region, Katkuri Venkat Rammanohar Reddy

Theses

Femoral component loosening and prosthetic stem fractures have renewed interest in conservative alternatives to conventional total hip replacements. The objective in this study is to get interfacial stresses of a acetabular surface replacement cup. This is done by performing finite element analysis of the model. A solid three - dimensional model with a grid of 3D isoparametric solid elements is generated using ANSYS, a powerful finite element analysis package. The stiffness is considered to be linearly proportional to the stress in the acetabular region. The stresses are determined by performing iterative finite element analysis. Stresses arp computed using two different …

Simulation Of A Microprocessor Controlled Drill Press, Arun J. Ayyagari

Theses

The concept of flexible manufacturing systems has ushered new dimensions into machine tool design. The power of this new technique is that a high degree of flexibility in a machine tool can be easily achieved by developing a software based control system as against conventional hard wired systems in existence.

To demonstrate this point, a microprocessor based control system is developed, in this thesis, to control the automated drill press. The Motorola MC6808 8-bit microprocessor is chosen as an example.

The microprocessor first evaluates the optimum cutting parameters for the given cutter size, work material and operation. It then uses …

Development Of Dynamic Analysis Program Mini-Dymac, Shang-Rou Shien

Theses

The computer program DYMAC developed by B. Paul automatically generates and numerically integrates the equations of motion of closed loop multi-body mechanical systems. The theory behind this program is Larange's form of d'Alembert's principle. However, it is not an easy task for the beginners to understand this program completely. If there is a simplified version of the program, it will be of great help for those people to understand the essential organization of the program.

Using the same theory of DYMAC, computer program MINI-DYMAC is developed in this thesis and hoped to serve as an educational version of DYMAC. For …

Graphic Display Of Robot Kinematics, Ramamurthy Vishwanathan

Theses

This thesis uses the HOUIE.BYLI graphics software package to simulate the kinematics of a six degree of freedom, MAKER I robot. The coordinate frames for the various links of the robot were established. The kinematic equations for the manipulator were developed snd solved using the techniques of inverse geometric transformations and transformations of objects in 3D space. A program was also developed to calculate the joint variables of the manipulator given any point on, and the orientation of, an object. These variable values are used to direct the robot end effector to the given point. This can be seen in …

Finite Element Analysis Of Multipass Effects Of Vehicles On Soil Compaction, David Pollock, J V. Perumpral, T Kuppusamy

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Finite element procedure was used to simulate multiple wheel loading and to predict its effect on soil compaction. Results of nonlinear analysis, conducted using an incremental loading procedure, show effects of tire size, soil type, and number of passes on soil compaction. The results of the study also demonstrate the potential use of the procedure in compaction related studies. However, experimental verification of the model is necessary before the procedure can be recommended for wider use.

Nebraska Summary: S022 Case-Ih 485, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S004 Deutz-Allis 6250, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S003 Deutz-Allis 6240, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

A Performance Comparison Of Solar Radiation Predictive Models For Both Fixed And Tracking Surfaces, William F. Marion

Retrospective Theses and Dissertations

Accurate performance prediction for a system utilizing solar energy requires accurate estimates of the solar radiation received by the collector surface. This thesis compares the performance of five different diffuse solar radiation models in estimating the diffuse radiation received by a tilted surface in the warm, humid climate of Central Florida.

The following models were studied: Isotropic Model, Temps and Coulson Model, Klucher Model, Hay Model, and Perez Model. The models were evaluated for both a fixed south facing surface and for three different tracking schemes suitable for photovoltaic applications. Model estimates were then compared to the solar radiation data …

Nebraska Summary: S023 Case-Ih 885, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S091 S.A.M.E Explorer 70dt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1586: Kubota L2550 2wd And 4wd Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1588: Kubota L3350 2wd And 4wd Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1587: Kubota L2850 2wd And 4wd 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1585: Kubota L2250 2wd And 4wd Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1584: Case International 3594 Powershift Diesel 12 And 24-Speeds, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1582: Case International 2394 Powershift Diesel 12 And 24-Speeds, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1583: Case International 3394 Powershift Diesel 12 And 24-Speeds, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1581: Hesston 180-90 Turbo Powershift Fiat Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1580: Hesston 100-90 Fiat Diesel 15-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1579: Hesston 45-66dt And 45-66 Fiat Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1578: Steiger Couger Cr 1280 Diesel 20-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Eigenvalue And Eigenvector Design Sensitivity Analysis For Nonlinear Beam Vibrations, Jian-Zhong Yuan

Mechanical & Aerospace Engineering Theses & Dissertations

A beam with immovable ends under large amplitude oscillations is axially subjected to an amplitude-dependent stretching force which is induced by the geometrical nonlinearity. The design sensitivity analysis for such a beam is investigated in this study.

Two variational formulations based on different approximations of nonlinear stretching force are studied firstly. The analytical equations of design sensitivity analysis for these nonlinear eigenproblems are then derived. Finally, a computational scheme using finite element method is developed to calculate the design sensitivity derivatives of the eigenvalue and eigenvector numerically. Numerical examples associated with the nonlinear eigenvalue and eigenvector analysis, as well as …

Design Of Multivariable Feedback Control Systems Via Spectral Assignment, Mohsen Marefat

Electrical & Computer Engineering Theses & Dissertations

During the past 15 year s significant advances have been made towards developing viable synthesis- techniques for multivariable feedback control systems. The entire aggregate of this theoretical work has been reviewed and consolidated. Diverse notations have been standardized into a single system. A two-step design philosophy for spectral assignment has been developed which first meets stability and time response requirements by assigning eigenvalues and eigenvector s and then provides for attainment of secondary objectives without significant deviation from the initial assignment. Finally, a computer-aided design package has been created to streamline the process of mathematical calculation and to allow users …

Test 1577: Steiger Couger Cr 1225 Diesel 20-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

A Survey Of The Literature On Moisture In Building Construction, Lawrence Charles Tiboldo

Theses

The aim of this thesis was to evaluate the literature on moisture in buildings for its usefulness in the understanding of the theory involved in moisture transfer in buildings. Because analysis of the effects of moisture migration and development of condensation control strategies in structures depends on the knowledge of heat and moisture transfer theory as well as on the documented data on building material properties, evaluation of the usefulness of the reference material will serve as an indication of the availability of pertinent information.

To fulfill this objective, the literature listed as references to Chapter 21 of the 1985 …