Digital Commons Network^™

Test 1598: Kubota M8030dt And M8030 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1597: Kubota M7030dt And M7030 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Substructuring Analysis For Impact Dynamics Using Ansys Finite Element Package, Chang Ho Cho

Theses

This thesis is intended to serve as an introductory guide to ANSYS finite element package for the analysis of impact dynamics. Substructuring technique has been used to reduce the degrees of freedom.

Finite element method is essentially a numerical technique to calculate elastic deformations. However, by introducing some techniques like gap element, the technique can be easily extended to rigid body dynamic analysis. To solve the equation of motion both for rigid body and elastic deformations, direct integration technique is used in this thesis, i.e., Houbolt method.

ANSYS is a large scale general purpose computer program for finite element analysis. …

Modal Analysis Of A Cantilever Plate, Ohseop Song

Theses

This thesis discusses the vibration of a thin, flat cantilever aluminum plate. Results are based on both an analytical finite element method using the ANSYS program and an experimental analysis using a digital Fast Fourier Transform (FFT) analyzer. The FFT analyzer permits extraction of modal parameters (natural frequency, damping, mode shape) for the plate.

Isoparametric Finite Elements For Axisymmetric Solids, Ramanand R. Shetty

Theses

The finite element formulation of axisymmetric plane stress analysis is used to develop a computer program for numerical implementation. The basic relations used to derive the finite element equations for a solid continum are reviewed in the thesis. The programming organization is summarized and program list is given in Appendix.

The program portion for isoparametric elements are borrowed from Numerical Methods in Finite Element Analysis by K. J. Bathe and E. L. Wilson, and various other subroutines are used from Mr. Huang's thesis on Micropolar elasticity analysis. Mr. Huang's computer program is based on the work done by Dr. Nakamura …

Plate Stress Analysis By The Finite Element Method, Wen-Jung Chuang

Theses

The finite element formulation of plate elasticity is presented and is employed in the development of the formulation of element stiffness equations. The programming structures are also summarized.

The finite element program PLATE cited from Prof. J. N. Reddy's " An Introduction to the Finite Element Method " has been used to solve the plate bending problems with quadrilateral elements. The problems solved are:

(1) deflections and stresses in a circular plate with all edges simply supported under uniform load.

(2) deflections and stresses in a circular plate with all edges clamped under uniform load.

each case including four different …

Chebyshev Approximate Solution For Stiff Problems, Kwo-En Hoh

Theses

Chebyshev polynomial and collocation methods are adapted to solve general ordinary differential equations ( initial-value problems and boundary-value problems ). Approximate solutions of initial-value problems are obtained in step-by-step fasion. the solutions have minimax absolute error in the interval and correct values at the end points. The approximate solutions of boundary-value problem will be continuous on the whole domain and have piecewise Chebyshev approximation characteristics in each subinterval of the chosen partition.

Computational Method For Robot Manipulator Dynamics Based On The Gibbs-Appell Equations, Kwang Bok Kim

Theses

Industrial robots are open-loop multi-degree of freedom mechanisms whose dynamic characteristics are described by nonlinear differential equations. The computations of forces and torques required at each joint of robot manipulator are crucial step for real time control of robot manipulators.

Vukobratovic developed a new computational method for rigid body articulated open-loop mechanisms based on the Gibbs -Appell equations to generate differential equations of motion for spatial open - chain mechanisms. To solve these equations, he introduced the recursive kinematic transformation matrices that represent the motion of each linkage with respect to the base linkage.

Computer programs are developed in this …

Laminar Flow In A Porous Pipe With One Plugged End, Pyne-Hwa Ku

Theses

A steady laminar flow through a co-cylinder porous pipe with one plugged end was investigated theoretically to obtain velocity, pressure and shear stress distributions.

An integral momentum equation and the Darcy's law for flow through the porous wall were solved numerically by the Runge-kutta method.

As the fluid is injected from the outer wall into the porous tube, the fluid in the inner tube is accelerated from rest at the plugged end to a fully-developed velocity profile at the exit of the porous tube. It was found that the coefficient of the wall shear stress and the dimensionless pressure drop …

Stress Analysis Of A Pressure Vessel By The Finite Element Method, Hsin-Te Liao

Theses

The objective of this paper is to take a finite element program, called ANSYS, to analyze the surface stress distribution of a thin-wall pressure vessel with a spherical head.

The computer program ANSYS, which primarily applies the principle of virtual work in solid continuum, has been used to solve shell problems with quadrilateral element. Problems solved are: <1> hoop stress <2> meridional stress (<)3) maximum shear stress.

In this paper, the theoretical finite element formulation of axisymmetric elasticity of the ANSYS program is presented.

Finally, some numerical examples of shells with spherical heads of various radius are given. The solution obtained from ANSYS is very …

Discontinuity Stresses Analysis In Pressure Vessel, Jan-Joo Liu

Theses

In this paper, the ANSYS general purpose finite element computer aided design program was used to perform a series of stress analyses for shells with heads of various shapes.

The analysis included maximum discontinuity stresses, stress contours and displacements induced in axisymmetrical shells subjected to internal pressure loading; especially at the junction of the cylinder and heads of various shapes.

CONICAL SHELL finite elements and TWO-DIMENSIONAL ISOPARAMETRIC finite elements were used in the analysis. The results of the analyses compared very favorably with solutions derived from membrane and bending theory solutions for pressure vessels.

The effect of longitudinal and hoop …

The Stress Distribution Of The Frp Pressure Vessel By Using Ansys Program, Lung-John Tsai

Theses

The objective of this paper is to take advantage of a general purpose finite element computer program, called ANSYS, to analyze the surface stress distribution of a fiber reinforced plastic (FRP) laminated composite pressure vessel. The vessel is subjected to internal pressure, which is assumed to be constant over the interior surfaces.

In this paper, the material is assumed to be orthotropic, and the stress-strain relationship linear.

A FRP pressure vessel subjected to an Internal pressure, 6.895 MPa (1000 psi), is taken as an example. The results show that this approach compares well with a theoretical solution.

Pressure Drop In A Strainer Element By The Finite Element Method, Wei-Long Chen

Theses

The pressure drop in a strainer element which consists of a channel and a diffuser has been investigated by the finite element method and the semi-empirical analysis.

An existing finite element program, FEM2D using the penalty parameter model, was employed. It was found that the range of Reynolds numbers in the strainer element was 0.193 to 4.824. For the pressure drop in the channel, the finite element method is in agreement with the analytical solution. For flow in the diffuser, the finite element method failed to give satisfactory results due to flow separation.

A Closed Form Image Force Function For Deposition Of Particles In A Cylindrical Tube, Hsi-Chung Chiou

Theses

This study investigated the behavior of charged particles suspended in a laminar steady incompressible flow in a cylindrical tube under the influences of image , inertia , viscous and gravitational forces. A new expression for the image force was obtained by introducing an approximate potential energy function. The velocity profiles employed in the analysis were uniform and parabolic.

The governing equations derived were based on Newton's second law of motion and were solved by a Runge-Kutta numerical method. The results were obtained for different values of Q, a dimensionless inertia-charge parameter. For a value of Q equal to zero the …

Thermal Energy Storage Using Phase Change Material With Multi - Melting Temperatures, Christakis Christodoulou

Theses

Three different models are developed in this investigation, for the study of thermal energy storage, using a phase change material with multi-melting temperatures. Using Model B as the basis, the developed partial differential equations are numerically solved by a finite difference method. Two computer programs were written based on that solution, one for the charging mode and one for discharging. Finally, using the computer programs, a set of results was obtained for both charging and discharging, utilizing calcium chloride hexahydrate as the phase change material with constant and multi-melting temperatures.

Implementation Of Finite Element Method On A Microcomputer, Chi-Yuang Huang

Theses

A finite-element program FEM2D has been implemented on a PHILIPS microcomputer. The program has a generation preprocessor and thus makes finite-element analysis on a microcomputer considerably easier than before, since it allows models to be created and edited much faster than by manual method. The interactive program FEM2D prompts the user to input data directly from the screen. It is convenient for the user, both in teaching and learning.

The FEM2D is a two-dimensional finite-element program capable of solving two-dimensional problems, such as plane elasticity, heat transfer and imcompressible fluid flow problems. It is developed with a formulation of a …

Circular Plate Analysis Using Finite Element Method, Shyh-Rong Chiu

Theses

The ANSYS computer program is the application of finite element methods to large-scale engineering problems. In this work the ANSYS program has been employed to solve the circular plate under uniformly loaded with various boundary conditions as follows: (1) clamped along entire edge, (2) simply supported along entire edge, (3) clamped at several points along the boundary, (4) simply supported at several points along the boundary, and (5) simply supported 36 points with 4 points clamped..

The results obtained from the ANSYS program illustrated that the finite element method has no boundary conditions constraints and presents good approximations to the …

Test 1596: Kubota M6030dt And M6030 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1594: Kubota M4030dt And M4030 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1595: Kubota M5030dt And M5030 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1592: Steiger Bearcat 1000 12-Speed (Caterpiller Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1593: Steiger Couger 1000 12-Speed (Caterpiller Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Maine Yankee Shutdown Assessment: A Report To Governor Joseph E. Brennan, Maine State Planning Office

Maine Collection

Maine Yankee Shutdown Assessment: A Report to Governor Joseph E. Brennan

Maine State Planning Office, Maine Office of Energy Resources, Maine Public Advocate

Executive Department - May 1986

Contents: Legal Process / Decommissioning Constraints and Costs / Public and Economic Costs and Benefits / Apprendices

Test 1591: John Deere 4050 Powershift Diesel 15-Speed (Chassis S/N Rw4050p006510 And Higher), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1589: John Deere 3150 And 3155 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1590: John Deere 4050 Quadrange Diesel 16-Speed (Chassis S/N Rw4050h006510 And Higher), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Deposition Of Suspensions In Convergent Channels Due To Electrostatic Image Forces, Kwok Wah Hui

Dissertations

The deposition of suspensions for uniform flow in convergent channels under the combined influences of inertia, viscous and electrostatic image forces was studied theorectically. The fluid phase was assumed to be two-dimensional, steady, uniform, incompressible and laminar while the particle phase was assumed to be uniform, steady, dilute and with negligible gravity effects.

Since the image force equations for convergent channels have not been derived, it becomes one of the main purposes of this study to perform the derivation of the image force equations. The lengths of the channels were chosen in a way that the exit area is only …

Deposition Of Particles In Tubes Due To Gravity And Electrostatic Charges, Win-Chung Chen

Dissertations

The deposition of particles in a parallel-plate channel and a circular tube under the influence of inertia, fluid viscosity, gravity and electrostatic image forces was studied by analytical and numerical methods. A laminar flow with uniform and parabolic velocity profiles was investigated with a particle initial velocity of zero as well as that of the local fluid velocity.

The governing equations were solved by the Lagrangian approach to obtain the particle trajectories from which the fraction of deposition was calculated. Closed form solutions for particle trajectory and a complete deposition of particles in a finite length of the flow passage …

Computer Aided Stress Analysis Of Long Bones Utilizing Computed Tomography, Shlomo Asher Marom

Dissertations

A computer aided analysis method, utilizing computed tomography (CT) has been developed, which together with a finite element program determines the stress-displacement pattern in a long bone section. The CT data file provides the geometry, the density and the material properties for the generated finite element model.

A three-dimensional finite element model of a tibial shaft is automatically generated from the CT file by a pre-processing procedure for a finite element program. The developed pre-processor includes an edge detection algorithm which determines the boundaries of the reconstructed cross-sectional images of the scanned bone. A mesh generation procedure then automatically generates …

Two And Three-Dimensional Isoparametric Finite Elements For Axisymmetric Micropolar Elasticity, Fuang-Yuan Huang

Dissertations

Finite element analysis program for isotropic and orthotropic axisymmetric micropolar (Cosserat) elastic solids are developed in this thesis. Isoparametric elements of 8- and 20- node are used to solve general three-dimensional problems, arid both 4- and 8-node elements are used for two-dimensional cases. Three-dimensional finite element formulation for cylindrical coordinate system is derived. Corresponding Fortran programs are then developed. Patch tests are performed for two-dimensional cases to verify the applicability of the finite element method to non-rectangular geometries. Several two-dimensional and three- dimensional problems for micropolar elastic solids are solved to verify the formulations arid computer program.

Good agreements were …