Digital Commons Network^™

Heat And Mass Transfer Characteristics During Vacuum Drying Of Wood, Mohamed Salah Elmetwaly, Lotfy Hassan Rabie Saker, Mohamed Sameh Salem

Journal of Engineering Research

The properties affecting the characteristics of heat and mass transfer during vacuum drying of wood are studied in this paper. The experimental work is carried out in 0.0365 m³ test rig vacuum dryer. The drying chamber dimensions are 0.5 m long and 0.305 m diameter carbon steel cylinder. This drying chamber is internally coated with epoxy paint, also this chamber is detachable closing caps at both ends meaning welded at one end and bolted at the other end to facilitate loading and unloading of the specimen. Two stainless steel heat exchanger plates with dimensions 0.3 m length, 0.15 m …

Internal Structure Of Incipient Soot From Acetylene Pyrolysis Obtained Via Molecular Dynamics Simulations, Khaled Mosharraf Mukut, Anindya Ganguly, Eirini Goudeli, Georgios Kelesidis, Somesh P. Roy

Mechanical Engineering Faculty Research and Publications

A series of reactive molecular dynamics simulations is used to study the internal structure of incipient soot particles obtained from acetylene pyrolysis. The simulations were performed using the ReaxFF potential at four different temperatures. The resulting soot particles are cataloged and analyzed to obtain statistics of their mass, volume, density, C/H ratio, number of cyclic structures, and other features. A total of 3324 incipient soot particles were analyzed in this study. Based on their structural characteristics, the incipient soot particles are classified into two classes, termed type 1 and type 2 incipient soot particles in this work. The radial distribution …

Energy And Environmental Analyses Of A Solar–Gas Turbine Combined Cycle With Inlet Air Cooling, Ahmad M. Abubaker, Adnan Darwish Ahmad, Binit B. Singh, Yaman M. Manaserh, Loiy Al-Ghussain

Institute of Research for Technology Development Faculty Publications

Sensitivity to ambient air temperatures, consuming a large amount of fuel, and wasting a significant amount of heat dumped into the ambient atmosphere are three major challenges facing gas turbine power plants. This study was conducted to simultaneously solve all three aforementioned GT problems using solar energy and introducing a new configuration that consists of solar preheating and inlet-air-cooling systems. In this study, air was preheated at a combustion chamber inlet using parabolic trough collectors. Then, inlet air to the compressor was cooled by these collectors by operating an absorption cooling cycle. At the design point conditions, this novel proposed …

Examining The Progress In Additive Manufacturing In Supporting Lean, Green And Sustainable Manufacturing: A Systematic Review, Catherine Maware, Rumbidzai Muvunzi, Tinotenda Machingura, Ilesanmi Daniyan

Institute for Sustainable Manufacturing Faculty Publications

The quest for waste reduction and the development of manufacturing processes that meet the economic, social and environmental requirements necessitate this study. Additive manufacturing is an emerging digital technology that can be used to seamlessly develop a product through material deposition in layers. The study aims to investigate the progress made in the development of additive manufacturing to support lean, green and sustainable manufacturing. The study employs a systematic literature review approach, specifically the Preferred Reporting Items for Systematic Reviews and Meta-Analysis (PRISMA). A total of 158 articles identified from different academic databases that detailed empirical, conceptual and theoretical findings …

Development Of A Rule-Based Monitoring System For Autonomous Heavy Equipment Safety, Amirpooya Shirazi

Department of Construction Engineering and Management: Dissertations, Theses, and Student Research

Roadway construction work zones are constantly exposed to interactions among construction equipment, workers, and vehicles. Furthermore, ensuring safety in these areas is considered a challenging task due to the complexity of the environment. As shown in the rising trend of fatal accidents in roadway work zones, current OSHA regulations in construction safety are insufficient in effectively detecting unsafe situations and mitigating the risks. Furthermore, best practices, such as internal traffic control planning (ITCP), exhibit critical limitations requiring continuous monitoring of active work zones as well as adjustments to the site coordination plans due to the dynamic nature of work zone …

Development Of A Large Format Additive Manufacturing System Based On An Off-The-Self Pellet Extruder, Aywan Das

Theses and Dissertations

Large Format Additive Manufacturing (LFAM), or Big Area Additive Manufacturing (BAAM), was introduced to resolve the limitations of the low deposition rate, low scalability, and therefore long print times, of traditional 3D printing methods when applied to the manufacturing of large structures and tooling. LFAM can be used to overcome the high conventional tooling costs of large structures. However, even with robotic setups, LFAM still mainly relies on quasi-planar, 2.5D printing strategies. This fails to reap the advantages of multi-axis printing, such as improved adhesion, reduced support material use, and the ability to create complex curved surfaces. In this research, …

Multidimensional Simulation Of Cool Diffusion Flame, Ejaz Ahmed

Theses and Dissertations

Understanding the behavior of spherical cool diffusion flames in microgravity conditions is crucial for advancing combustion research. This knowledge has significant implications for both fundamental science and practical applications, such as spacecraft fire safety and the development of advanced, high-efficiency engines that benefit from low-temperature chemistry. Spherical cool diffusion flames are typically characterized by peak temperatures between 500 and 1000K and are often followed by the radiative extinction of a hot flame. Some low-temperature ignitions can sustain indefinitely at around 700K, leading to chain-branching pathways that produce intermediate species such as C2H4, H2O2, HO2, CH2O, CH3O, and HCO. In some …

Accelerating Numerical Modeling And Optimization Of Structural Mechanical Systems, Fatemeh Hashemian

Theses and Dissertations

This research proposal presents Bayesian optimization and reduced order modeling methods to accelerate numerical analysis and design of structure mechanical system. First, a holistic framework of Bayesian optimization (BO) based on parameterized numerical models and genetic algorithm-guided adaptive sampling is developed to automate and accelerate the design of a front-loading washing machine. The research aims to address challenges associated with the model parameterization and global optimization and design. A multibody dynamics model of the washing machine incorporating a set of 9 key design variables is developed. The design variables are implemented to enable automated modifications of the dynamics model for …

Derivative Propagation Through Vortex Particle Method Simulation, Eric Green, Andrew Ning

Faculty Publications

Automatic differentiation (AD) is a powerful tool for evaluating numerical derivatives. In particular, reverse-mode AD provides numerical gradients in a way that is insensitive to the number of input variables. This makes reverse-mode AD well-suited for solving large optimization problems. However, reverse-mode AD has a particularly large associated memory cost because most intermediate values in operations need to be cached. This is problematic for large problems such as aerodynamics simulations, though, since the memory requirements can quickly become impractical. The solution implemented in this work is to provide analytic pullback expressions for functions for which many of the intermediate values …

Trajectory Optimization Of Evtol And Conventional Aircraft: A Comparative Analysis Of Vortex Particle Method And Vortex Lattice + Blade Element Momentum Theory, Andrew Tagg, Ryan Anderson, Cibin Joseph, Andrew Ning

Faculty Publications

Trajectory optimization of aircraft transition maneuvers can significantly influence the design of these systems, particularly when making decisions about aircraft geometry, propulsion sizing, and control system design. This paper presents the trajectory optimization of air vehicles including electric vertical takeoff and landing (eVTOL) as well as conventional aircraft. The study evaluates the influence of fidelity in trajectory design by comparing the use of two aerodynamic methods in the context of trajectory optimization. The mid-fidelity method utilizes a vortex lattice method (VLM) to model lifting surfaces while employing blade element momentum theory (BEMT) to model rudimentary rotor-wing interactions. The high-fidelity approach …

Solving Unsteady Potential Flow Problems In O(N) Time, Ryan Anderson, Andrew Ning

Faculty Publications

Design of vertical takeoff and landing aircraft is challenging in part due to significant aerodynamic interactions between rotors and wings. Computational models can aid in their design, but are computationally expensive. 3-D panel methods coupled with vortex particle wakes offer an attractive solution, but solving for the panel strengths scales poorly for large problems. Multigrid methods, such as Krylov subspace methods in conjunction with the fast multipole method (FMM), have been demonstrated to reduce the scaling to O(𝑁). We explore the performance and limitations of the Krylov-FMM method, traditional matrix-powered GMRES, LU decomposition, and a novel O(𝑁) multigrid approach to …

On The Correlation Between Pre-Processing Workflow And Dimensional Accuracy Of 3d Printed Parts In High-Precision Material Jetting, Karin Chen, Ahmed Elkaseer, Steffen Scholz, Veit Hagenmeyer

Mechanical Engineering

Material Jetting (MJ) is distinguished in the additive manufacturing field for its ability to create accurate multi-material functional objects with features in the range of few micrometers. Analyzing the impact of each step in MJ from virtual design to 3D printed object on the process response is essential for optimizing the technology’s capabilities. The current state-of-the-art reveals a gap in MJ regarding the fundamental understanding of the correlation between the pre-processing workflow and the geometrical and dimensional accuracy. This study aims to bridge this gap by examining factors such as utilization of different CAD software with diverse working principles, part-based …

Battery Management System Development For Electric Vehicles And Fast Charging Infrastructure Improvement, Yu Yang, Hen-Geul Yeh, Cesar Ortiz

Mineta Transportation Institute

The electric vehicle (EV) has become increasingly popular due to its being zero-emission. However, a significant challenge faced by EV drivers is the range anxiety associated with battery usage. Addressing this concern, this project develops a more efficient battery management system (BMS) for electric vehicles based on a real-time, state-of-charge (SOC) estimation. The proposed study delivers three modules: (1) a new equivalent circuit model (ECM) for lithium-ion batteries, (2) a new SOC estimator based on the moving horizon method, and (3) an on-board FPGA implementation of the classical Coulomb counting method for SOC estimation. The research team extends the traditional …

A Kinematic Analysis Of The Shoulder During The Volleyball Attack Using Euler And Helical Axis Methods, Victoria Jolliff

Biomedical Engineering Theses & Dissertations

The shoulder is a complex joint with a wide range of motion, including flexion, extension, abduction, adduction, and internal and external rotation. In volleyball, repetitive overhand movements can cause shoulder overuse injuries. The primary offensive move, the attack, involves the approach, arm cocking, arm acceleration, and follow-through phases. Motion capture analysis and techniques like calculating Euler angles and rotation about a mean helical axis can evaluate shoulder movements. This study aimed to calculate shoulder movements during each phase of the volleyball attack using the Euler angle YXY sequence and the helical axis method. Different attack types, such as cross-court and …

Repair And Surface Functionalization Of Fiber Reinforced Polymer Composites By Cold Spray, Ibnaj Anamika Anni

Theses and Dissertations

Fiber-reinforced polymer composites are widely used in industries and applications such as energy, automotive, defense, and aerospace. This study investigates the application of polymer cold spray, an emerging additive manufacturing process, for coating and repair of fiber-reinforced polymer (FRP) composites. The research starts with feasibility studies focused on the cold spray deposition of thermoplastic nylon-6 particles on woven glass fiber-reinforced composites (GFRP). A parametric study determines critical process parameters window, ensuring successful deposition and bonding without compromising the macroscale mechanical behavior. These findings indicate that the cold spray process does not adversely affect the fiber integrity or surface quality of …

Design Of A Pick-And-Place Robot With Computer Vision And Optimized Sorting Algorithms, Dan Kilula

Student Theses and Dissertations

In computer science, the Multiple Travelling Salesman Problem (mTSP) is a special case of Travelling Salesmen where one salesman travels through a network of cities (end nodes) and goes back to the starting city (start node) rather than stopping at the targeted end node. Numerous search and optimization algorithms are used to find the most time-efficient path for the salesman to visit each node. In this work 3 optimization methods and algorithms such as linear programming and A* pathfinding are utilized and compared to solve the mTSP applied to a 3 degrees-of-freedom pick-and-place robot that uses computer vision to detect …

Lunar: Automated Input Generation And Analysis For Reactive Lammps Simulations, Josh Kemppainen, Jacob R. Gissinger, S. Gowtham, Gregory Odegard

Michigan Tech Publications

Generating simulation-ready molecular models for the LAMMPS molecular dynamics (MD) simulation software package is a difficult task and impedes the more widespread and efficient use of MD in materials design and development. Fixed-bond force fields generally require manual assignment of atom types, bonded interactions, charges, and simulation domain sizes. A new LAMMPS pre- and postprocessing toolkit (LUNAR) is presented that efficiently builds molecular systems for LAMMPS. LUNAR automatically assigns atom types, generates bonded interactions, assigns charges, and provides initial configuration methods to generate large molecular systems. LUNAR can also incorporate chemical reactivity into simulations by facilitating the use of the …

Design, Fabrication, And Characterization Of Multifunctional Cellular Structures For Enhanced Impact Energy Mitigation Performance, Kazi Zahir Uddin

Theses and Dissertations

This dissertation investigates the relationship between the structural design of cellular solids and their macroscopic behavior and focuses on the customization of properties through advanced fabrication techniques. The concepts of density gradation and their integration in both non-ordered and ordered cellular structures have been proposed. The investigation focuses on the development of functionally graded foam materials (FGFMs) and mechanical metamaterials to obtain tunable mechanical performance. One significant focus is the fabrication of density-graded foam stacks with various interface adhesives. From the insights gained from the study of interfaces in density-graded foams, certain design and fabrication principles are applied to enhance …

Board 125: Work In Progress: Faculty Experiences And Learning Through Oral-Assessment Implementation In Engineering Courses, Minju Kim, Carolyn L. Sandoval, Josephine Relaford-Doyle, Torus Washington Ii, Saharnaz Baghdadchi, Nathan Delson, Marko Lubarda, Alex M. Phan, Curt Schurgers, Huihui Qi

Psychology Faculty Articles and Research

This WIP qualitative research paper explores faculty experiences with implementing oral exams in high-enrollment undergraduate engineering courses at a research university. With a primary goal to improve conceptual mastery, as well as a desire to ensure academic integrity in the sudden move to remote instruction at the height of the pandemic, a group of faculty in Mechanical and Aerospace Engineering and Electrical and Computer Engineering departments implemented oral assessments in their own engineering courses across several quarters. They formed a research group with educational developers in a teaching and learning center on campus, and investigated the impact of oral assessments …

Automating An Industrial Dishwashing System Using Hardware-In-The-Loop Plc Simulation With Factory I/O, Paniz Khanmohammadi Hazaveh, Nathir Rawashdeh, Dunsten M. X. Dsouza, Joshua Olusola, Joshua Albrecht, Eric Houck

Michigan Tech Publications

While industrial automation is growing in many industries, the hospitality industry has not seen much technological innovation recently. This leaves a wealth of potential for the implementation of automated solutions, especially at large-scale operations, like university dining halls or cruise ship restaurants. This paper details a student project developed in the advanced programmable logic controllers class. It is part of the master program in mechatronics. Students work in groups in a creative setting, where they learn to integrate various automation technologies and learn to write scientific publications. The project implements the automation of a student dining hall dishwashing system using …

Plc Multi-Robot Integration Via Ethernet For Human Operated Quality Sampling, Jeevan S. Devagiri, Paniz Khanmohammadi Hazaveh, Nathir Rawashdeh, Sai Revanth Reddy Dudipala, Pratik Mohan Desmuhk, Aditya Prasad Karmarkar

Michigan Tech Publications

In automation, quality control inspection is a critical requirement to ensure product standards. The goal of this work is to insure product quality without interrupting the production line flow. The multi-robot system presented, connects a programmable logic controller (PLC), as the main controller, to a conveyor belt and two FANUC industrial robotic arms via EtherNet/IP. Human interaction is implemented to pick a work piece from the moving conveyor and return it with a quality label. This label is used by the PLC to execute the correct robot action; either to return the inspected part to the conveyor or discard it …

Estimation Of Vehicle Traffic Parameters Using An Optical Distance Sensor For Use In Smart City Road Infrastructure, Rafał Burdzik, Ireneusz Celiński, Minvydas Ragulskis, Vinayak Ranjan, Jonas Matijošius

Henry M. Rowan College of Engineering Departmental Research

In recent decades, the dynamics of road vehicle traffic have significantly evolved, compelling traffic engineers to develop innovative traffic monitoring solutions, especially for dense road networks. Traditional methods for measuring traffic volume along road sections may no longer suffice for modern traffic control systems. This is particularly true for induction loops, a widely used method since the last century. In contrast, measuring techniques using microwaves or visible light offer better accuracy but are often hindered by the high cost of sensors. This paper presents new techniques for measuring traffic flow and other parameters that adapt to changing traffic dynamics using …

Large-Scale Research Infrastructure Empowers High-Quality Development Of Private Enterprises: Current Situation, Challenges, And Policy Recommendations, Lingling Zhang, Fuqiang Wang, Mingze Zhang, Zexia Li

Bulletin of Chinese Academy of Sciences (Chinese Version)

Private enterprises have become an important source of innovation in China’s economic development. Large-scale research infrastructure, as a crucial strategic support and innovation element for breaking through key technologies, provides a platform for the innovative development of private enterprises. At present, some large-scale research infrastructures in China, such as the China Spallation Neutron Source and the Shanghai Synchrotron Radiation Facility, have begun actively exploring mechanisms to serve private enterprises. These efforts have helped a number of private companies overcome critical technological bottlenecks and achieve original innovations. Nevertheless, in the current process of opening up large-scale research infrastructures to private enterprises …

A Country-Level Primary-Final-Useful (Cl-Pfu) Energy And Exergy Database: Overview Of Its Construction And 1971–2020 World-Level Efficiency Results, Paul E. Brockway, Matthew Kuperus Heun, Zeke Marshall, Emmanuel Aramendia, Paul Steenwyk, Thomas Relph, Michelle Widjanarko, Jeonghoo (James) Kim, Anjana Sainju, Julian Irtube

University Faculty Publications and Creative Works

Societal exergy analysis examines the flows of energy and exergy through societies, from primary (e.g. oil) to final (e.g. gasoline) to useful (e.g. propulsion) energy stages. By extending the study of energy to the useful stage, new insights into the under-represented role of energy in economic growth have been made. However, currently (a) country coverage is patchy and incomplete, (b) available data are based on varying methods and assumptions including efficiencies based on economic rather than engineering data, and (c) datasets are constructed using piecemeal computational approaches. To address these gaps, we construct a country-level primary-final-useful (CL-PFU) energy and exergy …

Design And Characterization Of 3d-Printed Hydrogel Lattices With Consistent Structural And Mechanical Anisotropy, Daniel Yoon

McKelvey School of Engineering Graduate Student Theses & Dissertations

This thesis explores the use of 3D printing to fabricate soft hydrogel lattice structures with consistent properties, including varying levels of mechanical anisotropy. Magnetic resonance elastography (MRE) is a non-invasive imaging tool to estimate and characterize the mechanical properties of tissue. MRE “phantoms” (physical surrogate models) have been used to assess how well MRE can measure and estimate mechanical properties. While gel phantoms generally simulate brain tissue, almost all have been isotropic. Prior studies have shown that white matter brain tissue is structurally and mechanically anisotropic. To validate anisotropic MRE, phantoms with controllable, reproducible anisotropic material properties are needed. This …

Patient-Specific Musculoskeletal Modeling Of Total Shoulder Arthroplasty, Brendan M. Curran

Electronic Theses and Dissertations

Total shoulder arthroplasty (TSA) is often considered a surgery of last resort for patients with debilitating pathologies of the glenohumeral joint such as osteoarthritis, humeral head fracture, and advancing rotator cuff tears. TSA replaces the articulation between the humeral head and the glenoid fossa, with the goals of relieving pain and restoring function. Two types of total shoulder implants are available: Anatomic Total Shoulder Arthroplasty (aTSA) and Reverse Total Shoulder Arthroplasty (rTSA). TSA survivorship is lower than that of the survivorship seen in total knee and hip replacements [1]. Shoulder muscle moment arms and lines of action have been measured …

Statistical Modeling Of Knee Morphology And Material Properties Considering Diverse Populations, Gabrielle Jeannine Kindy

Electronic Theses and Dissertations

Total Knee Arthroplasty (TKA) is a widely performed surgical procedure aimed at alleviating pain and restoring function in patients with severe knee osteoarthritis. Despite its general success, disparities in postoperative outcomes have been observed across different racial and ethnic groups, with minority populations often experiencing less favorable results. One potential avenue for improving the generalizability of orthopaedic implants is using Statistical Shape and Intensity Models (SSIMs), which can be used to incorporate patient variability directly into the orthopaedic medical device development workflow through population-based finite element analysis.

This work aimed to construct an SSIM from a diverse subject set, incorporating …

Kernel Ridge Regression In Predicting Railway Crossing Accidents, Ethan Villalobos, Constantine Tarawneh, Jia Chen, Evangelos E. Papalexakis, Ping Xu

Mechanical Engineering Faculty Publications

Expanding on the insights from our initial investigation into railway accident patterns, this paper delves deeper into the predictive capabilities of machine learning to forecast potential accident trends in railway crossings. Focusing on critical factors such as “Highway User Position” and “Equipment Involved,” we integrate Kernel Ridge Regression (KRR) models tailored to distinct clusters, as well as a global model for the entire dataset. These models, trained on historical data, discern patterns and correlations that might elude traditional statistical methods. Our findings are compelling: certain clusters, despite limited data points, showcase remarkably Root Mean Squared Error (RMSE) values between predictions …

Spectral Clustering In Railway Crossing Accidents Analysis, Ethan Villalobos, Hector Lugo Iii, Biqian Cheng, Miguel Gutierrez, Constantine Tarawneh, Ping Xu, Jia Chen, Evangelos E. Papalexakis

Mechanical Engineering Faculty Publications

This study employs graph mining and spectral clustering to analyze patterns in railway crossing accidents, utilizing a comprehensive dataset from the US Department of Transportation. By constructing a graph of implicit relationships between railway companies based on shared accident localities, we apply spectral clustering to identify distinct clusters of companies with similar accident patterns. This offers nuanced insight into the underlying structure of these incidents. Our results indicate that “Highway User Position” and “Equipment Involved” play pivotal roles in accident clustering, while temporal elements like “Date” and “Time” exert a diminished impact. This research not only sheds light on potential …

How Ai And Digitalization Can Help To Improve Managing Projects In Lean Manufacturing & Supply Chain Environment, Abhijeet Hange

Harrisburg University Dissertations and Theses

This research examines how digitalization and machine learning (ML) revolutionize project management in supply chain and lean manufacturing settings. To improve the efficiency and caliber of their operational procedures, Acuity Brands, Amazon, Walmart, Apple, and other medium-sized businesses—which are at the center of today's competitive markets—are resorting to automation and digitalization. With an emphasis on the fusion of digital and artificial intelligence (AI), the paper explores how successful transformation initiatives are essential to the automation and digitization of manufacturing and distribution hubs. The study uses quantitative methods approach to evaluate the benefits and drawbacks of these technology integrations by integrating …