Open Access. Powered by Scholars. Published by Universities.®

Digital Commons Network™

Open Access. Powered by Scholars. Published by Universities.®

Engineering

Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 190711 - 190740 of 196857

Full-Text Articles in Entire DC Network

Effect Of Axial Mixing In Gas Absorption, Sundareswaran Parameswaran Iyer Jan 1969

Effect Of Axial Mixing In Gas Absorption, Sundareswaran Parameswaran Iyer

Masters Theses

"The effect of axial mixing in the liquid phase on the performance of a gas absorption column was studied using the experimental data of Michael Brittan for the carbon dioxide and water system. In this study, piston flow conditions were assumed for the gas phase. A one-parameter mathematical model, which characterized the flow regimes in both the gas and the liquid phases undergoing plug flow conditions, was first curve fitted for its unknown parameter (i.e. the Number of Transfer Units) by a non-linear regression analysis procedure. The "AAPD" (i.e. the Average Absolute Percentage Deviation between the predicted value of the …

Go to article

An Investigation Of Transient Negative Resistance In A Cadmium Sulfide Device, John Irvin Giem Jan 1969

An Investigation Of Transient Negative Resistance In A Cadmium Sulfide Device, John Irvin Giem

Masters Theses

"An analysis has been made of a CdS device which exhibits a transient negative resistance at room temperature and low field strengths whereas previously reported cases of negative resistance in CdS were observed at low temperatures and moderate to high electric fields. The CdS bar was illuminated on one end in the vicinity of an ohmic In contact. Contact was made to the other end of the device with a rectifying Ag contact and the device was reverse biased. Experimental evidence and the analytical results both indicated that it is necessary that the material used to make the negative resistance …

Go to article

Solution Of The Two-Dimensional Multigroup Neutron Diffusion Equation By A Synthesis Method, William Ray Heldenbrand Jan 1969

Solution Of The Two-Dimensional Multigroup Neutron Diffusion Equation By A Synthesis Method, William Ray Heldenbrand

Masters Theses

"A method, called the higher mode synthesis method, for the solution of the two-dimensional neutron diffusion equation is developed. In this method, the two-dimensional eigenfunction is expanded in terms of one-dimensional fundamental and higher eigenfunctions. A substitute, weight, and integration procedure is applied and the two-dimensional equation is reduced to a one-dimensional equation in terms of expansion coefficients. The expansion coefficients are combined with the trial functions in order to obtain the two-dimensional eigenfunction. This procedure results in a significant reduction of computation time as compared with standard iteration methods"--Abstract, page ii.

Go to article

Design Of R-C-C-R Spatial Mechanism, Kao-Chien Hsei Jan 1969

Design Of R-C-C-R Spatial Mechanism, Kao-Chien Hsei

Masters Theses

"An analysis to design a particular R-C-C-R spatial mechanism was developed using tensor notations and operations. This specific R-C-C-R spatial mechanism can be used to couple two shafts intersected at a skew angle with constant rotating speed ratio. This skew angle, or bending angle of the two shaft, may vary from 30 up to 180 degrees. The governing equations of relative positions of the mechanism were formulated as a function of two variables: the bending angle of the shafts and the rotating angle of the input link. To exemplify the various design conditions, the design parameter versus the bending angle …

Go to article

Establishment Of A Torsion Pendulum And Its Evaluation, Ashwin Kantilal Ghatalia Jan 1969

Establishment Of A Torsion Pendulum And Its Evaluation, Ashwin Kantilal Ghatalia

Masters Theses

"A torsion pendulum apparatus has been constructed. The pendulum has been evaluated by studying the Zener relaxation in α brass. Three wire specimens of commercial alloy of Cu-Zn were used and the value of log decrement has been obtained by the method of free decay of the oscillations. The known Zener peak was observed"--Abstract, page ii.

Go to article

An Analysis Of An Audio Amplifier Utilizing An Operational Amplifier And Negative Feedback, Anthony Francis Lexa Jan 1969

An Analysis Of An Audio Amplifier Utilizing An Operational Amplifier And Negative Feedback, Anthony Francis Lexa

Masters Theses

"An audio amplifier utilizing a monolithic operational amplifier is analyzed. The analysis is a block diagram approach where the amplifier is divided into three parts; operational amplifier, power amplifier, and feedback network. A Fourier series analysis is used to describe the distortion and signal components of the amplifier output. The results of this analysis demonstrate the advantage of large negative feedback on frequency response and harmonic distortion. Using relatively few passive components a high quality audio amplifier is constructed with an output power of 15 watts RMS power and negligible harmonic distortion"--Abstract, page ii.

Go to article

Film Boiling From Inclined Flat Surfaces, Charles Ernest Price Jan 1969

Film Boiling From Inclined Flat Surfaces, Charles Ernest Price

Masters Theses

"The object of this investigation was to determine the effect of inclination on the heat transfer for saturated film pool boiling from a flat plate heater. Nitrogen at atmospheric pressure was used as the test fluid. The test plate was oriented at various angles from the horizontal position and the convective film coefficient was determined for each angle. Tests were conducted for heater angles of 0°, 30°, 60°, and 90°. The heater strip was placed in a container of the liquid and was heated electrically. Heat transfer results were obtained for plate temperatures ranging from 100 to 800°F. As the …

Go to article

A Study Of Different Types Of Connections To Structural-Steel Square Tubings, Chao-Sheng Chen Jan 1969

A Study Of Different Types Of Connections To Structural-Steel Square Tubings, Chao-Sheng Chen

Masters Theses

"Although square tubular element has long been recognized as an ideal structural member, its acceptance was limited by the lack of detailed knowledge on suitable connections related to this geometric shape. It is structurally inefficient to use a strong column poorly connected to a strong beam. So it is necessary to understand, in advance of adoption, the effect and behavior of different types of connections and to develop an efficient structural system. In this study, the ordinary column-to-beam framing with different types of connections has been investigated. The three types of connections are single-plate connection, double-angle connection, and multi-angle connection. …

Go to article

Thermal Fatigue Testing Of Die Casting Die Steels, Kulwant Singh Sabharwal Jan 1969

Thermal Fatigue Testing Of Die Casting Die Steels, Kulwant Singh Sabharwal

Masters Theses

"Thermal fatigue is a form of surface failure produced by repeated thermal stresses and is the main cause of die retirement in the die casting industry. A general review of the fundamental and practical aspects of thermal fatigue as encountered in the dies, based on earlier published work, is given and preliminary experiments in an effort to set up a suitable method of testing to study this phenomenon are then described. In the present technique developed to create the thermal conditions experienced by a die steel in aluminum die casting, a small portion of one face of a cylindrical test-piece …

Go to article

Static And Dynamic Instability Analysis Of Rigid Frames With Timoshenko Members, Carlton Lee Smith Jan 1969

Static And Dynamic Instability Analysis Of Rigid Frames With Timoshenko Members, Carlton Lee Smith

Masters Theses

"In this thesis, a technique has been developed to determine the natural frequencies of plane rigid frames with the consideration bending, shear deformation, rotatory inertia, and internal axial forces. The internal forces are functions of the instability load of the vibrating system for which the effects of bending and shear deformation on the stability of this structure are considered. For the sake of completeness, the matrix formulations for the dynamic or stability analysis of a rigid frame are given. The stiffness matrices of these formulations are then derived. The influence of shear deformation, rotatory inertia, and internal axial force is …

Go to article

Further Investigation Of The Traveling-Wave Transistor, Robert J. Feugate Jan 1969

Further Investigation Of The Traveling-Wave Transistor, Robert J. Feugate

Masters Theses

"A brief introduction to the concept of a traveling-wave field-effect transistor is presented. Analytic solutions for certain lossless and lossy special cases are derived and a numerical method for solution of the general case developed. A possible computer program for implementing this numerically is given and utilized to compare the traveling-wave transistor to a conventional field-effect transistor amplifier"--Abstract, page ii.

Go to article

Numerical Simulation Of Pressures In A Radical System, Vijender Nath Gopal Jan 1969

Numerical Simulation Of Pressures In A Radical System, Vijender Nath Gopal

Masters Theses

"The time-space location of an advancing front has been described in such a manner as to permit the calculation of frontal pressures when a heterogeneous (in permeability) radial system is subjected to water encroachment. A finite difference application has been developed to calculate these pressures at specified radial distances from the injection or production wellbore. These pressure have been further utilized to predict the pressures at the advancing front for different time intervals"--Abstract, page iii.

Go to article

A Computerized Method For Finding The Dynamic Response Of Multi-Mass Systems With Damping To Arbitrary Inputs, Bakulesh Balbhadra Patel Jan 1969

A Computerized Method For Finding The Dynamic Response Of Multi-Mass Systems With Damping To Arbitrary Inputs, Bakulesh Balbhadra Patel

Masters Theses

"A practical procedure for the systematic application of Foss's method to the solution of multi-degree-of-freedom damped systems is presented. It is relatively easy to determine the response of classically damped systems to various inputs. For non-classically damped systems the method proposed by K. A. Foss has been employed. This method gives an exact and complete solution for the response of linear multi-mass damped systems subjected to arbitrary inputs. Since the method requires lengthy and complex computations, the use of a digital computer is essential. In order to obtain the complete response of a multi-mass damped system to both sinusoidal and …

Go to article

Neutron Induced Changes To The Modified Ebers-Moll Transistor Model Used In The Net-1 Program, Kenneth Robert Smith Jan 1969

Neutron Induced Changes To The Modified Ebers-Moll Transistor Model Used In The Net-1 Program, Kenneth Robert Smith

Masters Theses

"The development of theoretical and empirical relations which predict the permanent changes to the electrical characteristics of silicon transistors is described in this paper. Analytical techniques are also developed to obtain the parameters used in the Modified Ebers-Moll transistor model. The method employed is to determine the effects on externally measurable characteristics and to relate these changes to the parameters in the Modified Ebers-Moll transistor model. Further, all nonlinear characteristics are related to the independent variables with interpolating polynomials and degraded characteristics presented. then degraded characteristics are used to establish the parameters for and parameter changes to the transistor model …

Go to article

A Study Of The Effect Of Tube Bundle Geometry On The Nucleate Boiling Region Of A Series Of Hydrocarbon Liquids, Robert Terry Montgomery Jan 1969

A Study Of The Effect Of Tube Bundle Geometry On The Nucleate Boiling Region Of A Series Of Hydrocarbon Liquids, Robert Terry Montgomery

Masters Theses

"The primary purpose of this heat transfer investigation was to determine quantitatively in what manner tube bundle geometry affects the nucleate boiling region of a tube whose single tube boiling characteristics are known. A series of tests were conducted with horizontal tube bundles which produced boiling in a saturated pool of n-hexane, n-pentane, and seven carbon (C₇) hydrocarbon mixture at atmospheric pressure. Tube bundle size and pitch were the principle independent variables considered. The phenomena of heater hysteresis and aging were also studied. Data are presented which indicates that aging probably is not a direct consequence of gas adsorption on …

Go to article

A Synthesis Procedure Of Distributed Rc Parameter Networks, Chun-Ming Wen Jan 1969

A Synthesis Procedure Of Distributed Rc Parameter Networks, Chun-Ming Wen

Masters Theses

"Synthesis procedures for driving-point functions and transfer functions in the w plane are developed in this thesis. For driving-point functions and transfer functions which are single-valued in s, where s is the complex frequency variable, the synthesis procedures were derived from the extension of the O'Shea's trasformation [sic]. For the transfer functions which satisfy the stability theorem in the w plane, a synthesis procedure is developed by using a distributed-lag element (DL) or a uniform distributed RC (UDRC) network with matched terminations"--Abstract, page ii.

Go to article

A Photoelastic Study Of The Stresses Around An Underground Opening And Its Support System, Alphonse C. Van Besien Jan 1969

A Photoelastic Study Of The Stresses Around An Underground Opening And Its Support System, Alphonse C. Van Besien

Masters Theses

"The stress conditions around openings in rock have long been of interest to the field of rock mechanics. The purpose of this investigation was to determine the stress distribution around an opening with a rib and wall-plate support system. A photoelastic model of the opening (a modified horse-shoe section) was loaded in the centrifuge to determine the effect of body loading. Both the tangential stress and the stress within the rock bench, due to the opening, were determined. The stress conditions within the bench were examined using simulated ribs and a loading frame. Application of the data is discussed, as …

Go to article

A Study Of Low-Cost Heat Exchangers For Desalination, Chin-Tsai Lin Jan 1969

A Study Of Low-Cost Heat Exchangers For Desalination, Chin-Tsai Lin

Masters Theses

"This investigation was proposed to search for simple and inexpensive but effective heat exchangers for the recovery of heat in water desalination by evaporation through non-wettable porous membranes. Aluminum was chosen as the material for constructing the heat exchangers. Various fluted arrangements and one plate type arrangement were chosen to increase heat transfer coefficients and conserve material. Equations correlating the heat transfer coefficients to temperatures and flow rates have been suggested for estimating the overall heat transfer coefficient at different conditions. The results of economic calculations indicate that the cost per unit transfer area of the exchangers in this investigation …

Go to article

A Study On Load Transfer Of Model Friction Piles, Richard Milton Franke Jan 1969

A Study On Load Transfer Of Model Friction Piles, Richard Milton Franke

Masters Theses

"Previous investigations concerned with disturbance of soft clay by driving displacement piles are summarized. The initiation of excess pore water pressures due to pile driving, and mechanisms of load transfer are also described, along with the applicapability of model pile testing in analysis of the various phenomena. Load tests were conducted on assorted sizes of model friction piles embedded in sedimented soil samples with consisted of a silt and clay mixture. Pilot holes of various diameters were cut in the samples. A theoretical load distribution curve was used to calculate the load transferred to the soil as a function of …

Go to article

Design And Use Of A Universal Logic Circuit, Mahendrakumar Punjalal Shah Jan 1969

Design And Use Of A Universal Logic Circuit, Mahendrakumar Punjalal Shah

Masters Theses

"Yau and Tang have designed universal logic circuits (ULC's) of three variables with 8 I/O pins. They assumed that only one variable was available as a free input variable in its true and complementary form, the others were available as fixed input variables and the circuit generated true and complementary outputs. Their design required 22 I/O pins for a four-variable ULC, constructed from three variables ULCs. This paper decrived [sic] an algorithm for determining the input-pin connections, directly from the K-map of a given output function, for any n-variable ULC. Forslund and Waxman have designed a three-variable ULC using the …

Go to article

Internal Friction Of Phase Separated Glasses, Scot Walter Taylor Jan 1969

Internal Friction Of Phase Separated Glasses, Scot Walter Taylor

Masters Theses

"The large internal friction peak observed in a 10Li₂O·10Na₂O·80SiO₂ glass was studied as a function of the degree of phase separation. Transmission electron microscopy was used to evaluate the type and degree of phase separation. No observable changes in the temperature position or height of the internal friction peak were observed at successive stages of phase separation. Phase separation of a mixed alkali borosilicate glass also produced no changes in the internal friction peaks. Phase separation is not considered responsible for the large internal friction peak observed in mixed alkali glasses"--Abstract, page ii.

Go to article

Plastic Analysis Of Beam - Columns, Ning-Cheng Tsao Jan 1969

Plastic Analysis Of Beam - Columns, Ning-Cheng Tsao

Masters Theses

"The results of an analytical study of the inelastic deformation of a wide-flange steel beam-column are presented. Emphasis has been placed on the influence of axial thrust on the pinned-end beam-column subjected to equal end moments with opposite direction. For this type of beam-column behavior, the relationship between the applied moment, axial load, and resultant curvature for the region in the plastic range has been studied in this investigation"--Abstract, page ii.

Go to article

The Influence Of Organic Matter On Shear Strength Of A Cohesive Soil, Kamran Rezvan Jan 1969

The Influence Of Organic Matter On Shear Strength Of A Cohesive Soil, Kamran Rezvan

Masters Theses

"The shearing properties of an organic A̲ horizon of Bryce clay were studied and compared with the properties of the same soil treated with hydrogen peroxide. The treatment was to remove the organic matter and isolate it as a variable. Tests were performed on artificially sedimented samples of the untreated, 75 percent untreated, 50 percent untreated, 25 percent untreated, and the treated soil. The effective stress failure envelopes were found to be higher for the untreated soil than that of the treated. The elastic deformation, however, was larger for the untreated samples. The pore water pressure development due to shearing …

Go to article

Determination Of Distillation Efficiencies For The Water-Methanol-Acetone System, Chorng Shyong Wang Jan 1969

Determination Of Distillation Efficiencies For The Water-Methanol-Acetone System, Chorng Shyong Wang

Masters Theses

"A pilot-scale, eight-plate, bubble-cap distillation tower with a multi-point temperature recorder and automatic sampling device was used to obtain operating data on temperatures and liquid phase compositions for distillation efficiency studies. The tower was run with a single feed, a total condenser, and a partial reboiler. At steady state, as indicated by constant temperatures, samples were taken and later analyzed by gas chromatography. A digital program was developed to calculate component efficiencies on each plate according to Holland's modified Murphree plate efficiency, utilizing the operating data, and reflux rate, the input and output flows and compositions, and vapor-liquid equilibrium data. …

Go to article

Study Of Diagnosability Of Binary Address Decoders, Girishchandra Mahendrakumar Gandhi Jan 1969

Study Of Diagnosability Of Binary Address Decoders, Girishchandra Mahendrakumar Gandhi

Masters Theses

"This paper studies the diagnosability of various types of binary address decoders. An attempt is made to develop a theory of diagnosis for logical faults that might occur in these logic nets. The developed theory is used to analyze these logic nets for various input combinations. Finally, the derivation of optimum diagnostic test sequences is considered"--Abstract, Page i.

Go to article

Telecommunications System Design Considerations For Advanced Logistic Spacecraft, James Myron Romberg Jan 1969

Telecommunications System Design Considerations For Advanced Logistic Spacecraft, James Myron Romberg

Masters Theses

"The telecommunications system design goals and functional requirements for an advanced logistic spacecraft are presented qualitatively. Advanced equipment and techniques that meet these system requirements and goals, that are within the state-of-the-art and that are believed to be economically feasible, are enumerated and described. System emphasis is on unification to minimize RF links and antenna subsystems, and on use of functional redundancy to assure satisfactory performance of critical telecommunication functions. The interaction of the telecommunications system design and the spacecraft mechanical, environmental, electrical, and operational interfaces are described in qualitative and quantitative terms. A practical spectrum of system interface characteristics …

Go to article

A Five-Spot Waterflood Process As Applied To The Digital Computer Based On The Prats Technique, Leonard Koederitz Jan 1969

A Five-Spot Waterflood Process As Applied To The Digital Computer Based On The Prats Technique, Leonard Koederitz

Masters Theses

"The technique for the prediction of injection rates and production history of a five-spot secondary recovery field pattern as presented by Prats has been significantly modified to permit rapid and accurate digital applications eliminating the heretofore prohibitive reliance upon electrolytic model results for intermediate data values following water front breakthrough"--Abstract, page i.

Go to article

Anodic Behavior Of Semiconducting Insb Single Crystals In Acidic Solutions, Lih-Da Hu Jan 1969

Anodic Behavior Of Semiconducting Insb Single Crystals In Acidic Solutions, Lih-Da Hu

Masters Theses

"Undoped, semiconducting single, n-type, InSb crystals were used to study the different etching behavior of the inverse {111} planes, to determine the apparent electron number of InSb under anodic dissolution (which corresponds to the sum of the absolute values of the oxidation numbers) and to investigate whether or not the inverse {111} planes show potential differences. The In {111}, Sb {111[repeating]}, {110} and {100} faces were highly polished, etched and immersed in various acidic solutions. Several new etch patterns of the inverse {111} faces were observed in giving other possibilities to distinguish both of the planes. The significant differences in …

Go to article

Numerical Simulation Of One-Dimensional Three-Phase Fluid Flow In A Stratified Petroleum Reservoir With No Cross-Flow, Ali Mohammed Akbar Jan 1969

Numerical Simulation Of One-Dimensional Three-Phase Fluid Flow In A Stratified Petroleum Reservoir With No Cross-Flow, Ali Mohammed Akbar

Masters Theses

"A numerical model for linear, three-phase fluid flow in a stratified petroleum reservoir has been developed for the purpose of studying water-flooding performance characteristics. Gravity forces, capillary pressure and cross-flow were neglected, but the fluids were considered compressible and evaluations of dissolved gas concentrations have been accounted for. The model was used in evaluating the performance of a water flood project for a hypothetical reservoir which contained the three phases of oil, gas, and water. The results were then compared with those obtained using the Dykstra-Parsons technique. The model produces results which were found to be similar to those obtained …

Go to article

A Continuous Method For Determination Of The Evaporation Rate Of Zinc, Paul Alan O'Neill Jan 1969

A Continuous Method For Determination Of The Evaporation Rate Of Zinc, Paul Alan O'Neill

Masters Theses

"A method for determination of the evaporation rate of zinc using a continuous recording balance has been devised. Tests were carried out under an inert gas over the range 600°C to 750°C with a total pressure of 1 atmosphere. It was found that the rate of evaporation doubled with an increase of 50°C in this range. Scanning electron microscope photographs show the crystalline nature of the condensate and the presence of a thin oxide layer on some solidified test samples. This oxide layer reduced the rate of evaporation by retarding the zinc vapor escape from the evaporating surface"--Abstract, Page iii.

Go to article

First Prev Next Last