Digital Commons Network^™

On The Interaction Of Aluminium And Iron Calcium Borate Glasses And Its Effect On The Properties Of Their Composites, Sherif K. Arif

Archived Theses and Dissertations

No abstract provided.

Comparative Study Of Lightweight And Normal Weight Concrete In Flexure, Mohammad Zareh

Dissertations and Theses

This investigation represents a comparative study of the flexural behavior of lightweight and normal weight concrete. Both theoretical and experimental moment-curvature characteristics of the tested specimens were used to study the flexural behavior.

A generalized computer program to determine the moment-curvature relationships of a singly reinforced rectangular concrete beam was developed.

For this limited study it was observed that lightweight concrete beams when compared to normal concrete beams achieve comparable moment capacity (about 92% of normal weight concrete) but exhibit higher deflections (about 40% more than normal weight concrete).

Sequences From Nonlinear Feedback Shift Registers., Richard H. Braasch

Electrical and Computer Engineering ETDs

1.1 General Aspects of Shift-Register Generated Sequences

An n-stage register is a device consisting of n consecutive two-state memory units controlled by a clock. At each clock pulse, the state ak (logical 1 or 0) of each memory stage, ak, is shifted to the adjacent stage of higher degree. A shift register may be converted into a code generator through introduction of feedback loops that compute a new shift register state based on the previous state of the register. This feedback shift register principle is illustrated in Figure 1-1.

Static And Dynamic Shear Behavior Of Uniformly Loaded Reinforced Concrete Deep Beams., Robert A. Crist Jr.

Civil Engineering ETDs

The objective of this research Kas to develop behavioral equations for reinforced concrete deep beams especially in the realm of shear capacity. A series of static and dynamic beam tests was performed to aid in the develop­ment of this objective.

Static testing was completed on nine uniformly loaded reinforced concrete deep beams. Span-to-depth ratios varied from 1.6 to 3.3. Intermediate-grade ASTM A 15 reinforcing steel was used. Nominal concrete strength was 3,750 psi. All beams contained longitudinal tensile reinforcing and no compressive reinforcing. Five beams contained an orthogonal array of web reinforcing coincident with the longitudinal axes of the beams …

The Use Of Graphical Techniques In Construction Management, Varne M. Kimmick

Civil Engineering ETDs

The relation and practical uses of graphics in construction management is a study area in which little work, with the exception of the critical path method, has been done. As the subject was begun, it was discovered there was little specific written material on the graphs themselves; therefore, a considerable portion of the thesis was devoted to basic graphics in order to make the discussion relative to construction more meaningful. Chapters I through VII cover the subject of basic graphics. The basic graphics portion was considered essential to the study in order to allow practical use of the work by …

Structural Stability In Earthquake Engineering., Aybars GüRpinar

Civil Engineering ETDs

To pate, only special cases of dynamic stability have been solved. In this dissertation, an attempt is made to obtain practical solutions to the stability problem in earthquake engineering.

A column supporting a concentrated mass at the top is treated as a single-degree-of-freedom system. The system is assumed to be linearly e·1astic with viscous damping. It is subjected to both horizontal and vertical random acceleration at the base, which are taken to be a band limited white noise simulating earthquake motions. The objective of this investigation is to find the probability of instability of the system.

Two methods of solution …

Fastener Strength In Diaphragm Braced Members, Amir Simaan, George Winter, Teoman Peköz

CCFSS Library (1939 - present)

SUMMARY In conjunction with research projects on diaphragm-braced members conducted at Cornell University, this investigation deals with the function of the fasteners in the braced system. In these systems, the diaphragm resists the lateral deflections of the braced members, in its plane, by virtue of its shear regidity (Qdr) and its shear strain capacity Yd (as a measure of strength). Considering the system in a slightly deformed shape, compatibility of displacements and forces between the diaphragm and the braced member at their connection locations, implies that the fasteners at these locations are subjected to the action of a system of …

Experimental Installations Of Impact Attenuation Devices, Bruce S. Siria, William M. Seymour, Don L. Cornette, James L. Miller

Kentucky Transportation Center Research Report

The expanding system of limited access, multilane highway facilities in the United States has enhanced traffic service between many varied origins and destinations. As a result, these facilities have not only reduced travel times and travel costs, but have generated additional travel by virtue of their technological splendor. The increasing dominance of multilane highways in terms of percentage of total vehicle miles travelled has produced a revolution in highway engineering philosophy. Higher design speeds, increased lane widths, lateral separation of opposing traffic streams, absence of passing restrictions, and increased traffic capacities were attributes intuitively sought. An ironic result is the …

Measurement Of Soil Moisture By Attenuation Of A Vertically Polarized Radio Wave, Arlo D. Mickelsen

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The purpose of this thesis is to determine feasibility and to investigate some of the problems encountered in making soil moisture measurements using radio wave propagation. The procedure consists of propagating a vertically polarized wave over the earth and measuring the field strength attenuation. A brief summary of present methods of measuring soil moisture is given.

Certain aspects of radio wave propagation theory are discussed, covering such topics as the surface wave, the space wave, the skin depth, and the effect of the dielectric constant on radio wave propagation. Based on this theory, measurement parameters such as frequency, antenna separation, …

Computer Simulation Of Urban Runoff Characteristics Within Salt Lake County, Robert Newman Parnell

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A hybrid computer program is developed to simulate the outflow hydrographs of two urban watersheds located within Salt Lake County, Utah. The gaged outflow of the watersheds provided a checkpoint for comparing the observed and the simulated final outflow hydrographs.

The outflow hydrographs for each subzone of the two watersheds were obtained by abstracting interception, infiltration and depression storage from each subzone hyetograph. The outflow of the subzones were routed to the Jordan River, the final outflow point of the two watersheds. The final hydrographs of the watersheds were combined and compared with the gaged flow.

The uniquenesses of this …

A Correlation Study Of The Washington Pre-College Test Scores To Determine Which Scores Are The Best Predictors Of Success In Flight Aviation At The Big Bend Community College, Richard H. Pearce

All Master's Theses

The purpose of this study is to determine how a student's Washington Pre-College test results and his high school grade point average can best be used in deciding which people have the greatest chance to succeed in the Big Bend Community College flight aviation program. For the past four years of the aviation program it has been necessary to choose approximately seventy students for the program from as many as two hundred applicants. The counseling staff of the college in cooperation with the flight aviation department has used the high school grade point average as a primary tool in order …

Strain Measurements At Extremely High Temperatures Using Moiré Fringe Techniques., Joseph W. Neudecker Jr.

Mechanical Engineering ETDs

A new procedure is described for using the moiré-fringe technique to measure strains in structural materials at temperatures exceeding 1300 °C. The principal factor found to be necessary for successful viewing of moiré patterns at extremely high temperatures is the use of reflected laser light for viewing the strained grid on the material. This factor is extensively discussed and experiments are described in which strain measurements were successfully made on graphite specimens at elevated temperatures. It is concluded that the techniques described constitute a more feasible method of measuring strains at higher temperatures than is possible by any other known …

A Study In The Design And Development Of A Baseball Pitching Machine, Neal M. Lundwall

Theses and Dissertations

Throughout history man has had the need of services which require great skill or tremendous strength or delicate consistency on the part of those who perform. Much of the time he has turned to the machine to accomplish these requirements.

Transition From Laminar To Turbulent Flow For A Two-Phase Mixture, Mohammed Sharief Qureshi

Theses and Dissertations

A phase is simply one of the states of matter. Multiphase flow is the simultaneous flow of several phases. Two-phase flow is the simplest case of multiphase flow.

A Computer Simulation Of A Partial Venous System Of A Human Lower Extremity, David C. Smith

Theses and Dissertations

The human body is truly a fascinating and complex creation of our Maker. Because of the complexity and variability, many of its workings were little known until recent years. Some of the more amazing facts of the circulatory system follow. If the individual blood vessels of a single adult, i.e., artery, arteriole capillary, venule and vein, were laid end to end, they would extend more than 60,000 miles. For the average adult, the heart beats 70 times per minute; for the well-conditioned athlete, 50-60 beats per minute; and for the extraordinary athlete, as few as 37 times per minute. The …

Transient Convective Heat Transfer Coefficient For Injection Into Rigid Vessel, James Edward Steiger

Theses and Dissertations

The purpose of this study was to develop and demonstrate a method for experimentally determining the convective heat transfer in a rigid vessel while air was being injected. The heat transfer took place between the air in the pressurized vessel and the surrounding walls which were maintained at a temperature of 32 F. with a circulating ice water bath. The study considers the effects of injection geometry and injection flow rate on the heat transfer process. The problem of heat transfer after injection has been considered by Means (1), and was responsible for establishing this study. The experimental technique used …

Conduction Error In Thermocouples Embedded In Low Conductivity Material, Tumkur G. Nagaraju

Theses and Dissertations

Thermocouples are generally used as devices to determine the internal temperature of any material. The purpose of the temperature measuring device is to measure the temperature which would exist at some known location if the device were not present. The thermocouples are embedded in the material in order to study the temperature-time history of the point of location. The presence of the thermocouple induces error in the temperature measured. This error becomes significant if heat is conducted into or away from the point of measurement by the sensor itself, or if the sensor insulates the point. This would result from …

Hydraulics Of Waste Stabilization Ponds And Its Influence On Treatment Efficiency, Kenneth A. Mangelson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The treatment efficiency of waste stabilization ponds depends on many factors, the most important of which are generally presumed to be the biological factors such as the type of waste and the organic loading. However, the biological activity in a pond is greatly influenced by the environmental conditions of temperature, wind, sunlight, and the hydraulic flow patterns. In the past little attention has been given to the hydraulic characteristics of waste stabilization ponds. Specifically, little consideration has been given to the gross flow patterns within stabilization ponds as affected by the shape of the pond or lagoon, the presence of …

A Comparison Of Technologist Needs And Training Requirements Of The Major Industries Within The State Of Utah, Gene E. Forsberg

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The technologist needs and training requirements were determined from a selected cross-section of Utah industrial firms.

The larger industries were significantly more aware of the training requirements and capabilities of four-year technologists than were the smaller firms.

A significant difference was found regarding general and specialized training required by each firm. Thirteen of the 16 responding firms indicated specialized training as being most important.

The 10 areas of technical training rated most critical in their order of importance were: electronics, technical writing, electricity, English, mathematics (calculus and above), machine shop, manufacturing processes, physics, and metallurgy and design.

There was no …

Hydrologic Inventory Of The Great Salt Lake Desert Area, Gary L. Foote

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Utah, located in the arid southwest, is a state that experience s chronic water shortages. The pattern of valleys and high mountain ranges that exists in the state produces sharply contrasting differences in climatic conditions . Desert valleys in the western portion may receive as few a s 4 inches of precipitation in a year while headwater areas in the Wasatch Mountains receive 60 inches or more. Wide cyclic as well a s geographical variations of precipitation added to uneven seasonal distribution makes development and efficient utilization of water resource s vital though difficult.

In order to make the most …

Phosphorus Distribution In The Bottom Sediments Of Hyrum Reservoir, Kirk L. Schmalz

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The distribution of phosphorus in the sediment of Hyrum Reservoir was studied by collecting and analyzing 84 sediment samples for total, inorganic, organic, and water-soluble phosphorus.

Sample locations were mapped by triangulation and sediment phosphorus distribution maps were made. Sediment analysis showed average total phosphorus content of 755 micrograms per gram, with organic phosphorus composing approximately 97 percent of total phosphorus.

Sediment samples showed variability in phosphorus content which precluded identification of point sources of phosphorus input to the reservoir. Several areas of comparatively higher phosphorus content in the sediments were shown with isopleth maps.

An estimate of the extent …

A Statistical Theory Of Avalanche Breakdown In Silicon, Terence Vincent Sewards

Electrical and Computer Engineering ETDs

A statistical theory of avalanche breakdown in silicon is presented, based on the conventional Boltzmann transport equation. The scattering mechanisms considered are impact ionization (electron-hole pair production), phonon emission and absorption, thermal generation and recombination. The resultant critical field is found to depend on the recombination statistics, which were ignored in previous theories of avalanche breakdown. The theoretical temperature dependence is compared with the temperature dependence of the breakdown voltages of three conunercial diodes.

Development Of An Electronic Means Of Weighing Vehicles In Motion, Ben W. Carr Jr., Rolands L. Rizenbergs

Kentucky Transportation Center Research Report

An in-stream weighing platform was designed and installed in the eastbound lane of I 64 and 75 near Lexington, Kentucky. The broken-bridge scale platform was designed with the outer edges of the two sections supported on hinges and contiguous edges supported by two 20,000-pound capacity load cells. The assembled scale measures 4'-6" x 10'-1/2" with a total weight of about 2,000 pounds.

The electronics developed for the system included digitizing circuitry which processed the load cell signals and recorded the data on digital magnetic tape. Computer processing of the field data produced tabular information on vehicle speed, axle spacing, number …

Experimental Concrete Pavement Containing Fly-Ash Admixtures [1971], James R. Philpot

Kentucky Transportation Center Research Report

The report enclosed is somewhat routine inasmuch as it documents a repeat of a portion of an earlier experimental project. The previous project was on Poplar Level Road; our final report was dated July 1966 (KYHPR-64-1). Special Provision No. 70 was used also on the Jefferson Freeway project. However, there was no "control section" involved in the current project. The Jefferson Freeway project was authorized by the BPR under P.P.M. 60-2 only (now PPM 20-6.3).

The most significant findings from both projects concern the water requirements the concrete containing the fly-ash admixture. Whereas laboratory tests indicated reasonable expectations of a …

An Experimental Investigation Of The Vortex Sink Rate Sensors, Nelson L. Lu

Mechanical & Aerospace Engineering Theses & Dissertations

The vortex sink rate sensor device consists basically of an ideal sink flow between two coaxial disks. A sink tube was located at the center of one disk. The vortex was created by the rotation of the unit about its axis of symmetry. Five inch and 10 inch diameter of porous couplers were used for the air chamber here in this investigation. Several slenderness parameters, i.e., the ratio of the sink tube diameter to the height of the air chamber ^ro/n were conducted. Two probes were used to measure the static pressure and stagnation pressure respectively at various positions …

A Theoretical And Experimental Study Of An Unsteady Pressure Measuring System, Ramesh R. Batki

Mechanical & Aerospace Engineering Theses & Dissertations

Experiments were performed to determine the frequency response of gas filled instrument tubes, and the results were correlated with a theoretical model. The theoretical model developed by Bergh and Tijdeman for a series connection of thin circular tubes and volumes was studied in full detail and employed. A measuring system was designed and built to measure pressure ratio and phase lag employing thin nylon or vinyl tubes and strain gage transducers. 1'leasurements were performed using cathode ray tube, strip chart, analog techniques and also a commercial electronic function analyzer and the various results were compared. The theoretical and experimental influence …

Transverse Vibration Of A Class Of Orthotropic Plates, Nicholas J. De Capua

Dissertations

This study determines the eigenvalues, eigenvectors, and nodal patterns of a class of orthotropic plates whose geometry is governed by the equation

(x/a)^α + (y/b)^β = 1,

where the parameters a, b, a, and a permit the plate geometry to vary over a range which includes the rhombus, circle, ellipse, square, and rectangle.

Variable thickness, inplane forces, and mixed or discontinuous boundary conditions are also considered. The following assumptions have been employed:

i). plate is thin with respect to other dimensions,

ii). deflections are small,

iii). rotary inertia and shear are neglected.

The method of analysis employed is …

A Theoretical And Experimental Study Of The Mechanism Of Axoplasmic Convection In Nerve Fibers Driven By Peristaltic Surface Waves, Robert John Biondi

Dissertations

In the study of cell biology, investigators have found that substances which are produced within the cell nucleus are sometimes found throughout the cell at points distant from the site of production. In the case of nerve cells (neurons), this is particularly dramatic because of the unusual elongated geometry of these cells.

A neuron possesses a cylindrical tubular extension called an "axon" or "axis cylinder" which is characterized by a large length-to-diameter ratio (10³-10⁶). The existence of a continuous proximo-distal flow of axoplasm within these cylindrical axons has now been demonstrated by numerous investigators. In …

The Development And Use Of Scattering Parameters For Semiconductor Junction Devices, Lee Dennis Philipp

Electrical and Computer Engineering ETDs

Scattering parameters are developed for diodes and tran­sistors. The parameters are developed through a modification of the wave equation from quantum mechanics. The effects of pulsed X-ray radiation on these devices is then calculated with the use of these parameters.

Various methods of analyzing semiconductor junction de­vices are discussed. These methods include diffusion theory, invariant imbedding and quantum mechanics. The background in these areas necessary for a discussion of semiconductor models is outlined.

Models resulting from the three basic approaches are presented. These include the Ebers-Moll Model, the Charge Control Model, the Linville Model, the Gore Model, the MLB (McKelvey, …

Ole Miss Engineer 1971

Ole Miss Engineer

No abstract provided.