Digital Commons Network^™

On The Entropy Of Kiswahili, Luhanga M.L, T.G.B. Nyambo

Tanzania Journal of Science

Cover and King’s gambling approach to the estimation of the entropy of English is used to estimate the entropy of Kiswahili. Experimental results obtained show that Kiswahili has average entropy of approximately 1.76.

Theoretical And Experimental Study Of Inlet Manifold Pressure Profiles Using Compensated Transducers, P Mtui

Tanzania Journal of Engineering and Technology (TJET)

Computer simulation and experimental findings on single cylinder four-stroke cycle engine were done with a view of getting more realistic inlet manifold pressures. Since there is a direct relationship between the inlet pressure profiles and the volumetric efficiency of the engine, then there is a possibility of utilizing the knowledge of these profiles to enhance better engine air flow characteristics and hence improvement of engine performance.

The simulation program is based on hometropic process with constant specific heats where the results were validated using experimental findings of the engine with varying engine speeds.

Experimental results are obtained by measuring manifold …

The Performance Of A Horizontal Flow Roughing Filter/Slow Sand Filter Water Treatment Plant In Tanzania, Mbwette T. A

Tanzania Journal of Engineering and Technology (TJET)

The performance of a water treatment plant comprising of the Horizontal f Iow Roughing F i Iter (HRF) / Slow Sand Filter (SSF) System was evaluated by monitoring the water quality of the inlet water and the plant filtrates for a Improper operational procedures and period of two months. the absence of adequate maintenance of the plant was found to have resulted to relatively Iow removal efficiency. This subsequently improved as a result of plant rehabilitation and introduction of new operational procedures and became comparable to the performance of HRE/SSF plants documented in literature. For example, as a result of …

Control System Design Program Based On Cascade Compensation, Fredrick Ishengoma

Tanzania Journal of Engineering and Technology (TJET)

CAD is becoming more widely accepted in the design and analysis of control systems. A program has been developed for analyzing single-input single-output linear time-invariant control system. The application of the progranl for frequency domain design of cascaded phase lead and phase lag coinpensators is briefly discussed. Two examples to illustrate the program are presented.

Optimization Of Dispersed Flor Pond For Bacterial Removal, Mayo A. W

Tanzania Journal of Engineering and Technology (TJET)

The design of waste stabilization ponds is seldom done with consideration of optimum pond dimensions. The analysis of pond dimensions within practical limits in dispersed flow ponds on the basis of minimum cost for the predetermined bacterial remova) ef ficiency, with the aid of computer is presented. The data collected in the pilot and full scale waste stabilization ponds at the University of Dar es Salaam Was used as input to the computer program. The results shows that pond configuration and climatic conditions which have influence on bacterial mortality rate have a re:narkable influence on pond cost

Hydrodynamic Stability Of The Breakwater Extension At Rrviksand, Norway, Alfonse Dubi

Tanzania Journal of Engineering and Technology (TJET)

The fishing port of Årviksand in Norway, which is situated on an open coast, is artificially harboured by breakwaters. The northern and southern breakwaters which were built in 1930—ies and 1950—ies respecti vely have been on several occasions damaged by heavy storms. This resul ted in the need for further protection by extending the northern breakwater. This paper describes one of the hydrodynamic tests on the breakwater extension. The breakwater, with a berm breakwater concept design, is subjected to the joint probability of sea level elevation and wave heights (in other 'fatigue" test). words , It is found that cover …

Evaluation Of Wind Data Records To Predict Extreme Extreme Wind Speeds In Tanzania, L Lwambuka

Tanzania Journal of Engineering and Technology (TJET)

The progress made towards evaluation of local wind data records to pred ict extreme values of wind speeds in Tanzania is being presented . Records of wind data, stored continuously since 18 years, have been compiled and statistically processed. Extreme value theory of Fisher —Tippet Type I has been fitted into the data to abstract extreme values of wind speeds for locations at which the wind data records were obtained. A reliable wind map of Tanzania containing basic wind speeds at 18 locations across the country has been produced. The basic wind speeds are being recommended for des ign against …

The Hydraulic Performance Of A Vortex Tube Foector, F Mtaro

Tanzania Journal of Engineering and Technology (TJET)

The vorle.r tube silt exrrac/or consists of a pipe, rhe crest of which has a slit and lies flush across lhe canal bed.With minimal warer loss, I.oe bedload is extracted through lhe slil settling canal back ro the river, thus reducing or eliminating the bedload transported in main canal. Ihe resulting swirling flow phenomena is of complex nature and depends on sc conirol paramerers, as a result of which previous empirical design approaches have yielded conflicting guidelines. By means Of a simplified hydraulic system, the flow mechanism and energy in rhe can be determined.

Absorption Of Nitrogen Oxides Into Sodium Hydroxide Solution In A Packed Column: Effect Of Gas Flowrate And Temperature, J Katima

Tanzania Journal of Engineering and Technology (TJET)

The effect of gas flow rate and temperature on the absorption rate of nitrogen oxides (NO ) and column absorption eff iciency has been studied using a 2M goåium hydroxide (NaOH) solution in a packed The absorpt ion process was carried out at atmospheric column. pressure, with NOV concentration ranging between 150 and 10000 pp:tt, NO/N02 ratio of O and 1 iquid flow rate of O .8 1/ min. The gas flow rate was varied from 20 to 60 1/17 in and the temperature from 25 to 45 c. It was found that Ehe column absorption efficiency increases with decreasing …

Parking Demand And Supply In The Central Business District Of Dar Es Salaam City, Theophil Rwebangira

Tanzania Journal of Engineering and Technology (TJET)

The Central Business District (CBD) Of Dar es Salaam city is currently experiencing severe congestion. Among the major causes of this condition is lack cf enough parking facilities. Obstructions due to vehicles parked on the roadway and increased vehicle circulation by drivers looking for a mace to park This paper reports on a recent study are major contributors to congestion. which evaluated the demand and supply as vell as usage of parking spaces in the CED. The f indings indicate that there is currently an acute shortage Of parking spaces, especially of off—street parking spaces. For the existing facilities, there …

Energy From Biomass: Combustion And Gasification, G John

Tanzania Journal of Engineering and Technology (TJET)

Some fundamental facts of the combustion Of BIOMAS are outlined and di scussed . It is suggested that these provide guidelines for rhe development Of successful practical combustors. Furthemore, a realisation Of energy conversion from the same in gasfier is presented.

Nn Investigation Of Nitrogen Oxide Abscwption In Packed Columns, J Katima

Tanzania Journal of Engineering and Technology (TJET)

An experimental study was carried out on the performance of a packed column to study the absorption mechanism of nitrogen oxides (NOx). Two packed columns were set up, one with wall wiper rings to reduce wall effects and one without. Both columns were packed with stainless steel lessing rings and operated at fixed gas and liquid flow rates (40 and 8 L/min, respectively), atmospheric pressure, temperature (25°C), and sodium hydroxide concentration (8% w/w). The NOx (NO₂ and N₂O₄) equilibrium concentration and feed concentrations of up to 7000 ppm were used. The results indicated improved performance in the column with wall …

Flood Forecasting In Tanzanian Catchments, Omari Rumambo

Tanzania Journal of Engineering and Technology (TJET)

Floods are still a problem to many countries in the world todate. Floods do cause damages to property and sometimes loss to human life. Flood control measures by structural and non—structural methods are avail able in the literature . However , structural flood control measures are financially infeasible in most developing countries today. Flood forecasting is a non—structural measure for reducing flood damages. It is a means of providing early The Li near f 1 ood warnings to flood prone areas . Perturbation Model has been appl ied for real time flood The Linear forecasting in Tan zanian catchments . …

Experimental Investigations On The Behaviour Of Wood In Transverse Compression, A Mrema

Tanzania Journal of Engineering and Technology (TJET)

Experimental investigations were done to study the behaviour of wood in transverse compress ion. Three key variables were incorporated in the experiments to study their influence on the •nriables were the orthotropic ratio of the behav iour. These material, the geometry of loading and that of the specimen . Deformation measurements were made at selected locations on test specimens by means of strain—gage based clip gages. Results from the experimental measurements were compared to previous deformation predictions made by a finite element analysis (9) . There is a very good agreement between measured values and those obtained trom the finite …

Density Measurement For Corrosive Solutions At Elevated Temperatures, Kimweri, H

Tanzania Journal of Engineering and Technology (TJET)

In this work, apparatus for measuring densities of corrosive solutions at high temperatures was developed and used. Densities of dilute aqueous sulphuric acid solutions, containing different amounts of zinc and iron salts were measured at temperatures up to 185°C. In view of the good agreement between consecutive measurements for each solution and the density of water obtained by using this apparatus with that given in literature, for all experiments, the apparatus is recommended to be used for measuring densities of corrosive solutions at high temperatures.

Electrical Equivalent Method For The Calculation Of Vibrations In Transformers, D Chambega

Tanzania Journal of Engineering and Technology (TJET)

Noiselevel calculations may be done using an electrical equivalent method. So far a single mass and a double mass vibrating system may easily be represented by equivalent electrical circuits which are in turn useful for analysis. Multimass vibrating systems like transformers do not have straightforward methods which can enable analysis of noiselevels. This paper attempts to develop such a method by extending the method applicable to a double mass vibrating system. Then the validity of the method is tested using a transforme

Factors Affecting Capacity Utilization In Industries: Hierarchical Analysis, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper provides a hierarchical analysis of the factors affecting capacity utilization in Tanzanian industries. Several factors were identified and sent to randomly selected industries in Tanzania for ranking. The collected data was summarized and analyzed. The analysis made use of a known procedure, the 'Analytical Hierarchy Process' (AHP). The final results shows a ranking of the factors, on various hierarchical levels as to their percentage contribution in lowering the capacity utilization.

Design, Operation And Maintenance Considerations Of Iiorizontal Flow Roughing Filters Preceding Slow Sand Filters, T Mbwette,

Tanzania Journal of Engineering and Technology (TJET)

The paper mentions some of the reported uses of Horizontal Flow Roughing Filters (IIRF) in drinking water treatment plants in Europe before briefly reviewing research activities carried out in the use of IIRF prior to Slow Sand Filters. Design, operation and maintenance aspects Of HRF are reviewed on the basis of the laboratory and field tests carried out in Tanzania and Switzerland, respectively in addition to experience gained in operation of a number of plants already built to date. Design aspects are introduced from the point of view Of its philosophy and optimization strategies before design guidelines are given. Important …

The Stability And Sate Dimensioning Of Circular Masonry Arches, A Mrema

Tanzania Journal of Engineering and Technology (TJET)

An analysis of masonry arches where collapse is assumed to occur by the hinging of voussoirs upon each other is made. The behaviour of the arch material is assumed to be such that the plastic theory is valid. Certain aspects related to the properties So far the approach by of the line of thrust are clarif led. writers has been based on the conventional view that the 1 ine of It is shown that pressure is tangential to the line of thrust. this is not the case in general. Definitions are given on what is meant by "line of thrust" …

Nitrogen Oxides Rbsorption Into Sodium Hydroxide Solution In A Packed Column Column: Effect Of Naoh Concentration, J Katima

Tanzania Journal of Engineering and Technology (TJET)

Experiments have been conducted to evaluate the ettect of sodium hydroxide (NaOH) concentration upon the absorption rate of nitrogen oxides (NO ) and packed column performance. The absorption process using was carried out at atmospheric pressure and 29B K, concentrations between zero and w/ w, NO/ NO ratio of 0.5 and NO concentrations between 150 and 10000 ppm in an air mixture. The performance of the calumn was enhanced by the presence of hydroxyl ions ( 0B - ) relative to the absorption into water, however, The absorption it was found to be independent of NaOH concentration. rate of NO …

Carrying Capacity And Cracking Resistance At The Of Halving Joints In Reinforced Concrete Beams, S Mpinzire;

Tanzania Journal of Engineering and Technology (TJET)

Results are presented from tests on 3 beams having discont inuous support zones. All Of them had web and diagonal shear reinforcement. TWO out Of the three represented beams, their test results have been analysed in a paper designated part I which appeared in the Uhandisi Journal , Vol. I December 1989. They have been presented in this paper for compar ison purposes. The third beam has been made to invest i gate the effect of anchoring diagonal shear reinforcement by spot Welding method. The third beam was tested With two concentrated loads in the span. In all beams several …

A Finite Element Analysis Of Wood In Transverse Compression, A Mrema

Tanzania Journal of Engineering and Technology (TJET)

A two dimensional finite element analysis is utilized to predict the stress and strain distributions for wood in transverse compression. Important key var iables are incorporated into the ana lysis to define their influence on the stress and strain distributions. These variables are geometry of loading, geometry of specimen and the orthotropic ratio of the material. Based on the finite element analysis results, relationships are arising stress from developed relat ing maximum stress concentrations to the above three variables. possible appl ications of the results from this study relate to the development of more efficient design of connections such as …

Comparative Study Of Inlet Manifold Tuning To Enhance Supercharge, Mtui L

Tanzania Journal of Engineering and Technology (TJET)

Computer model ing and experimental results on a single cylinder, four-stroke cycle engine for best air flow characteristic is The modeling analysis is based on hornet ropie fluid di scussed . The model n g resul s is flow w it. h constant: specific heats. included to val idat.e the s imulation program against experimental results with widely vary ing manifold lengths and engine speeds. ExperimenLal results are obtained by measuring air f low rates Lo the inlet valve during steady g Late speed Of Lhe engine. Manifold tuned lengths are Obtained for a range Of speeds by exper and …

Effects Of Feed Solids Concentration On Dual Functionality Of A Hydrocyclone., Zanzu M

Tanzania Journal of Engineering and Technology (TJET)

The dual functionality, i.e. thickening and classification of a 50.8mm diameter hydrocyclone has been investigated. A metallurgical slime consisting of a 50% mixture of quartz and petroleum coke was used in the tests. It was found that in order to achieve both thickening and classification at the same time, the pressure drop across the hydrocyclone, the underflow diameter and the feed solids content have to be subtly controlled.

Transport Matrices Of Finite Beams Resting On Elastic Foundations, M. W. Giger

Tanzania Journal of Engineering and Technology (TJET)

A method of derivation of the coefficients of the transport matrix for a finite element resting on one and two-parameter elastic foundation soils is outlined. The coefficients are summarized for both the Bernoulli–Euler and the Timoshenko beam model in tabular form, for general reference. In addition, bounds on the parameters describing beam/soil flexure, beam and soil shear, which govern the validity of the two-parameter elastic solutions are provided in graphical form.

Investigation On The Use Of Ethyl Acetate As Solvent For Seed Oil Extraction, E. L. Rivera Porras

Tanzania Journal of Engineering and Technology (TJET)

An investigation on the use of ethyl acetate as a solvent for the seedoil industry was carried out. As hexane is the most used solvent in extraction of oil from seeds, the study focuses on the comparison of the two solvents. The parameters studied were: contact time between solvent and seed cake, temperature of the solvent, quantity of solvent used for extraction and type of solvent. The results are presented on a relative basis where hexane is given a factor of 100. From the results obtained it can be seen that ethyl acetate is in general a better solvent than …

A Study Of Load Bearing Capacity Of Piles Driven In The Zanzibar Harbour Submarine Soils, A. M. Dubi

Tanzania Journal of Engineering and Technology (TJET)

The rehabilitation of the Zanzibar Port involved, among other things, driving piles into the submarine soils. Pile driving fractures the coral and as a result creates a gap filled with loose fractured coral between the unfractured coral and the pile. Grouting of the external surface of the pile is done to strengthen the fractured coral. In this paper, two grouted working piles (TP6 & TP61), randomly chosen from the pile group, were load tested to twice the design load. The test results indicate adequacy of the bearing capacity of the grouted piles.

Force Displacement Relationship For The Prediction Of Structural Fluttering, Ladislaus Lwambuka

Tanzania Journal of Engineering and Technology (TJET)

A new presentation of force displacement relationship for the prediction of structural fluttering is discussed in this paper. This topic is limited to a detailed discussion of the derivation of the equations of motion for the rigid streamlined airfoil/flat plate system of three degrees of freedom, which yields expressions for aerodynamic resultant forces due to a steady air flow. The equations of motion presented herein are derived from the conventional classical complex presentation transformed into real matrix equations. This new presentation of the equations of motion constitutes the foundation for the latest state-of-the-art of predicting critical wind loads on the …

Numerical Investigation Of A Non-Newtonian Material Through A Sudden Pipe Expansion, V. G. Masanja

Tanzania Journal of Engineering and Technology (TJET)

A numerical method for solving two dimensional elliptic boundary-value problems of fourth order is used for finding stationary solutions of the equations of motion for a laminar flow through a sudden pipe expansion of an incompressible non-Newtonian fluid with a constitutive equation of the Reiner-Rivlin (R-R) type. Results for the Newtonian fluid, which is a special case, are in excellent agreement with those by previous investigators and they demonstrate the reliability, superiority and accuracy of the method. Results for the non-Newtonian cases could be of value for fixing ideas about visco-elastic behaviour although the R-R fluid allows only inelasticity: this …

Agitation Requirements For Complete Drawdown Of Floating Solids In Stirred Tanks, Joseph Philemon Mmbaga

Theses

The agitation requirements for complete drawdown of floating solids in mechanically agitated tank vessels has been studied both theoretically and experimentally.

A semi-theoretical equation has been derived on the basis of Kolmogoroff's theory of isotropic turbulence to determine the minimum impeller speed required for drawdown. The equation contains one adjustable parameter which has been found to be a function of the impeller type and position in the tank vessel.

The equation was tested using various vessels and impeller configurations. The solid phase consisted of high density polyethylene (density = 897kg/m³), low density polyethylene (density = 840kg/m³) …