Digital Commons Network^™

Measurement Of Dust Resistivity And The Effect Of Filter Operating Parameters On Its Value, S Issangya

Tanzania Journal of Engineering and Technology (TJET)

Methods of measuring electrical sensitivity of a dust layer have been outlined and the porous electrodes cell was used to measure the electrical resistivity of a dust layer and to determine the influence of various parameters. Dust layer thickness and applied voltage had no influence. Resistivity depended on particle size, packing density, temperature, and air relative humidity. Glass beads and limestone powders of different mean particle sizes were used. Temperature was varied from 20–100 °C and air moisture ranged from dry to near saturation. The results may help in understanding the performance of electrically enhanced fabric filters, which are influenced …

Solar Heater For Curing Tobacco Part I: Overview And Theory, J John

Tanzania Journal of Engineering and Technology (TJET)

This is two parl paper. In part one of the papet; an overview on the use Of packed beds on heat collectors To be used in natural convection systems is presented. A brief theoretical background and literature review has also been presented. Theoretical analysis and performance equations are pre- sented in detail. Two zypes of absorbers are proposed for investigation. The firs,' one will be with flow below the absorber and the other with flow "'through " {he absorber. These shall be compared with the conventional flat plate collector. For comparing the performance, packings of different materials, shapes, and sizes …

Evaluation Of The Influence Of The Magnetic System In Relays, D Chambega

Tanzania Journal of Engineering and Technology (TJET)

The paper evaluates the influence of different cores on the performance of relays. In particular two types ofc-cores, all made from IOW quality mag- netic steel, are considered. The two cores, one butt-constructed and the other interleaved, are mathematically modelled and the tesults are analyzed and obtained experimentally. Then the two sets of results are compared with those ofa c-shaped core of excellent magnetic material with the aim of qualifying the influence of the core material. It is observed that the method of constructing the core also influences the performance.

Power Shedding Experiences And Lessons In A Township, Alexander Kyaruzi

Tanzania Journal of Engineering and Technology (TJET)

This paper presents how power shedding by taking out one of the trans- former high voltage fuses causes phase imbalance. And for the same elec- nicc,l energy output generator fuel consuntption with unbalanced phases is 12.5% of The fuel consunwtion with balanced phases. Furthermore it is shown thal energy efficient lighting by use of energy efficient bulbs can reduce load shedding.

Polymer Supported Z-N Catalysts For C2h4-Polymerization,I: Development Catalyst Preparation Method, S Mteza

Tanzania Journal of Engineering and Technology (TJET)

Substantial improvement of low sensitivity pressure transducers aiming at obtaining a more realistic output signal is discussed. The output signal direct from these transducers has deficiencies of amplitude attenuation and phase lag, thus the measured values are not necessarily the true in- stantaneous values. In order to correct for such shortcomings the unit step response of these transducers is also studied experimentally. A math- ematical model is established based on the experimental results to build up a compensation circuit which is then included in the instrumentation setup to eliminate these deficiencies. The effectiveness of the compensated transducer is demonstrated by …

Application Of Improved Pressure Transducers For Pressure Measurements, P Mtui

Tanzania Journal of Engineering and Technology (TJET)

Substantial improvement of low sensitivity pressure transducers aiming at obtaining a more realistic output signal is discussed. The output signal direct from these transducers has deficiencies of amplitude attenuation and phase lag, thus the measured values are not necessarily the true in- stantaneous values. In order to correct for such shortcomings the unit step response of these transducers is also studied experimentally. A math- ematical model is established based on the experimental results to build up a compensation circuit which is then included in the instrumentation setup to eliminate these deficiencies. The effectiveness of the compensated transducer is demonstrated by …

Influence Of Arc Discharge Duration On Turbulent Mass Burning Rate, E Mushi

Tanzania Journal of Engineering and Technology (TJET)

The influence of arc discharge duration on turbulent mass burning rate was investigated for turbulent r.m.s vglocities of u '=1.73 m/s and u'=4.5 nfs. Methane air mixtures were used at equivalence ratios ranging from 0.83 to / .25. Flame size was obtained through schiieren photography while the intensity Of CH chemiluminescence emissions was used to measure mass burning rate. A variable spark duration unit was used for ignition sparks and all the experiments were done in a fan stirred bomb. Discharge duration has no effect when the equivalence ratio is I. For higher values longer duration inoeases the burning rate …

Optimum Geometrical Parameters For Prismatic Folded Plate Roofs: System- Atic Search Approach, N Mwitta

Tanzania Journal of Engineering and Technology (TJET)

Folded plate structures have unique structural advantages over conven- nonal beam-and-slab structural forms. Selection of optimum geometrical parameters in design would make folded plate roofs more appealing to the national construction industry in terms ofcost. This paper presents a study on shape optimization of prismatic folded plate roofs for minimum weight of the structure per unit covered area. A computer based systematic search approach has been employed.for the optimization study, while the tranyeer matrix method has been used for analysis. Curves opriinum geometrical parameters versus span have been pre sented for three commonly used shapes of prismatic folded plate roofs. …

Pulping Of Sisal Fibres: Effects Of Chemical Concentration, Na-Zs03/Na2c03 Ratio And Fibre To Chemical Ratio, J Katima

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on pulping of hard fibres extracted from the leaves Of agave sisalana using sodium sulphite buffered with sodium carbonate as pulping chemical. The cooking was carried Out at 1680Cfor a cooking period of 6 hours, with varying chemical concentration, sodium sulphite to sodium carbonate ratio and fibre to chemical ratio. The results show thar boll! the pulp yield and pulp viscosity decæase with increasing chemi- cal concentration, whereas Kappa number of pulp decreases to a limit of about 16.45. Brightness increases significantly with an increase in the ra- rio of Na2S03/Na2C03. The pulp yield obtained indicated the …

Electricity Consumption Patterns In Domestic House Holds, H Kadete

Tanzania Journal of Engineering and Technology (TJET)

Electricity tariff increases from 1988 to 1992 are presented. They are Compared with salaries paid to parastatal workers over the same period. Monthly expenditures on electricity are also presented. Electricity con- sumption profiles have been recorded. The typical end use electrical ap- pliances for each household category have been identified. About 69% of electricity is used for cooking in high demand households. In medium demand households electricity used for lighting dominates ar about 49%. Measurements indicate a 3 peak power consumption profile for domestic dwellings. Voltages of 180V were recorded instead of the expected 230V nominal. Power factor is nor …

Hazards Inherent In The Use Of Electricity, Alexanda Kyaruzi

Tanzania Journal of Engineering and Technology (TJET)

This paper describes hazards associated with thc use of electricity, empha- sis is given to hazards due to electric shocks. A survey carried Out by the author indicated that 68.5 % of all reported accidents and 55.3 % of all fatal accidents are due to people Coming into contact with normally non current carrying metallic parts. The necessary conditions which need to bc present in an electric system for electric shock to occur are described. How the human body responds to Various severity of electric shock is dis- cussed. Possible solutions, and how to prevent or minimise the effect Of …

Regionalization Of Hydrologic Information In Tanzania (Low Flows), Onyekwuluje C

Tanzania Journal of Engineering and Technology (TJET)

Hydrologic infornjation is required for the planning and design Ofwater resource projects. However, Hydrologic infonnation is always lacking at points of interest. Regionalization is ained at estimating hydrologic infor- mation such as low flow statistics at ungauged sites. Hydrologic informa- tion from 63 catchments in Tanzania has been analysed. In this paper, pooled flow duration curves for 1, IO, 30, 60, and 90 days duration have been established. Regression equations between the low flow indices (i.e. 95 percentile and for a IO day duration, average annual yield (AAY), av- erage daily flow (ADE)) and catchment characteristics were developed. The pooled …

Influence Of Turbulence On Methane-Air Flame Speed, E Mushi

Tanzania Journal of Engineering and Technology (TJET)

Experimental study Of the influence qfturbulence on flame speed for meth- ane-air mixtures has been conducted in afan stirred bomb using schlieren photography. It has been observed that turbulence increases flame speed but above KLe=O. 18 (KLe is the product Of the dimensionless Karlovitz flame stretch factor and the Lewis number) turbulence quenches the flame. Inminarflame kernel is observed to prevail in the early stages of flame development in a turbulent mixture. Further, the laminar burning velocity plays a significant role in turbulent combustion. It is proposed that the increase in flame speed is a result of flame wrinkling.

An Alternative Method Of Interfacing A Dc Motor To A Microprocessor For Mo- Tion Control, M Selekwa

Tanzania Journal of Engineering and Technology (TJET)

A Simple and cheap alternative method Of interfacing a permanent mag- net dc motor to a motion control using switch- ing transistor motor drivers is presented. This method involves the use Of very few transistor-transistor logic (TTL) devices and a 555 timer to pro- duce a pulse width modulated (P WM) signal which is required by the mo- ror driver. The motor driver in this case should be of an H-bridge type. Like other methods currently in use, it relieves the MPU of all timing func- tions which are necessary in the generation of P WM signals. The present method, …

Quality Problems Facing Tanzanian Industrial Firms, M Msafiri

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on the results of a study of quality problems facing Tanzanian industrial firms. The results show that Tanzanian firms do not set goals with respect to quality and quality management, thus their qual- ity performance is generally poor. A Ithough there are a number of opera- tional problems constraining the companies, the main problems lie with the internal management of the quality function. Extensive ideas and sug- gestions for improving the performance of the quality function are given.

Measurement Of Dust Resistivity And The Effect Of Filter Operating Parameters On Its Value, Allan Issangya

Tanzania Journal of Engineering and Technology (TJET)

Methods sed to measure the electrical resistivity of a dust layer and to determine the influence of various parameters. Dust layer thickness and applied voltage were found to have no influence. Resistivity depends on particle size, packing density, temperature, and air relative humidity. Glass beads and limestone powders of different mean particle sizes were used. Temperature was varied from 20–100 °C and air moisture ranged from dry to near saturation. The findings may help in understanding electrically enhanced fabric filters, whose performance is influenced by the resistivity of the collected dust layer.

Optimal Capacity Allocation Truck Industry In Tanzania:A Case Of National Transport Corporations(Ntc), R Mgaya

Tanzania Journal of Engineering and Technology (TJET)

This paper tries to examine truck transportation service in Tanzania, particularly, in National Transport Corporation’s subsidiary companies - Regional Transport Companies. It provides an analysis based on operations research approach on resource allocation, specifically, truck allocation, with an aim of trying to minimize running costs and hence improve profits. It is established that there had been higher running costs and hence decline of profits in some Regional Transport Companies due to misallocation of capacity. However, this problem had been compounded by some other factors as discussed in the paper. It is recommended that these Regional Transport Companies and other transport …

Dual Versus Single Spark Plug: A Critique, I Mshoro

Tanzania Journal of Engineering and Technology (TJET)

Dual spark plugs are occasionally employed on certain modern Spark lg- nited (S') engines, viz lean burn engines. Their benefit has generally been noticed in the operating conditions whenfuel-air mixture is very lean, or when a larger proportion of EGR has been employed, or during the part load conditions and so on. An extensive literature survey has indi- cared an interesting spectrum of reasons for gains due to the dual spark plug. A consistent explanation is found to be missing which can describe the behaviour of the engines with single versus dual spark plugs There are quite "few researchers who …

Suitability Of The Present Strategic Information Technology Planning (Sitp) Methodologies To The Developing Countries, A Victor

Tanzania Journal of Engineering and Technology (TJET)

The needfor strategy formulation, or in general terms strategic planning, for IT is considered as one of the most important aspects of IT manage- ment. To this end, there are a number of IT strategy formulation method- ologies world-wide. These methodologies were developed over a span of time, starting from mid 1960's when IT use started to become a serious issue in the developed countries, and continued with the trends in IT de- velopment and use, as was applicable in those countries. Morc recent of the methodologies were developed through improvements on earlier ones, and based on the new challenges …

Improvement Of Solar Salt Works Performance, J Katima

Tanzania Journal of Engineering and Technology (TJET)

Coal, asphalt, black oil paint, naphthol green b and alkali blue 6b were testedfor improvement Of solar energy utilisation in solar salt manufacture. It was found that the use of alkali blue 6b dye dissolved in raw seawater improves efficiency by 3.6 percent. Both modifications could increase solar salt works with a coal coated surface than one employing raw seawater dyed with alkali blue 6b.

Thermodynamics And Transport Proper- Ties Analysis Of Natural Gas From Songosongo In Kilwa- Tanzania, G Mrema

Tanzania Journal of Engineering and Technology (TJET)

Analysis ofthermodynamics and transport properties was carried outfor six natu- ral gas samples from Songosongofield in Kilwa - Tanzania using PRO/II simula- for. Properties of most interest in gas processing (due to their influence on the sales value) such as density, specific gravity, critical parameters, bubble point and dew point, enthalpy, latent heat of vaporisation, molecular weight, boiling point and phase were investigated. In addition composition of the gas was com- pared with that from elsewhere. The gas was assumed to be at a temperature of 30C and a pressme of 150 bar before pressure let down station. Results indicated …

A Conceptual Approach To Water Resources Management For A Catchment In Tanzania, F Mwanuzi

Tanzania Journal of Engineering and Technology (TJET)

In hydrology/Water resources, normally rainfall data are available for longer periods than runoff data. Many attempts have been made to extend these runoff data by using system approach and conceptual models. The conceptual approach to simulate runoff at the outlet ofa catchment is based on the physical processes involved in the transformation of rainfall into runoff (river flow). In this paper a conceptual model, (SEAMOD) has been used. This model has a limited number of parameters to optimize when compared to other models like the sacramental model. Also it requires less input data. The model assumes that the storage is …

A Check Parameter Method For Use In Designing Relays, H Kadete

Tanzania Journal of Engineering and Technology (TJET)

Low quality magnetic steel available locally has been successfully used as core material for a relay. New design principles as well as construction procedure used in development of a prototype are presented. Then the new approach is assessed and found to deliver acceptable accuracy.

Critical Evaluation Of The Effects Of Changes Made To Roughing Filters Of Mpira-Balaka Plant On Its Treatment And Operational Performance, C Zulu

Tanzania Journal of Engineering and Technology (TJET)

Mpira Balaka, a full scale rural water supply project was constructed in Ntcheu, Malawi, in 1988 utilising Slow Sand Filtration (SSF) as the main treatment process and roughing filtration as the pretreatment method,following the promo- tion of this technology by various international institutions. During the rainy seasons, the treatment plant for Mpira Balaka failed to cope with the high raw water turbidity, resulting into very short filter run times and hence also to unavoidable distribution Of very turbid water to the rural communi- ties as a result Of by-passing the filters. Of the fifty or so existing rural projects in …

Practical Aspects In Sensing Vrm Magneti- Sation Characteristics For Rotor Position Detection, N Mvungi

Tanzania Journal of Engineering and Technology (TJET)

The detection of rotor position (stator/roror poles overlap) in a variable reluc- tance motor using the dependence of permeance on rotor position is the core of the effort to eliminate the need of a physical position sensor in the rotor shaft in the positional feedback operation of the motor. The reliability of the whole proc- ess Of eliminating the need of a physical sensor rests squarely On the ability to measure the instantaneous permeance ofa phase when the motor is in operation and at stand still. This paper presents an experimental investigation on the in- triguing problems of obtaining repeatable …

Effect Of Reduced Plate Width On The Structural Behaviour Of A Triangularly Folded Plate Barrel Vault, S Manyele

Tanzania Journal of Engineering and Technology (TJET)

Various methods of analysis have been employed to predict the  structural behaviour of the Triangularly Folded Plate Barrel  Vault, with conflicting results. A review of past analytical  and experimental investigations carried out on the structure  show that theoretical analysis based on a smaller effective  width rather than the overall plate width is capable of closely  predicting the deflection behaviour of the structure.  This paper presents an experimental study of the behaviour of  a triangularly folded plate barrel vault with physically reduced  plate width.  It is found that physical reduction of the plate width to  correspond to ‘theoretical’ effective width weakens …

Development Of A Knowledge Based System For Wastewater Pipeline Failure Risk Assessment, Adam Mayanzani Ngaliga

Engineering Management & Systems Engineering Theses & Dissertations

The purpose of this thesis was to study and analyze the wastewater pipeline failure risk assessment process, and then design and develop an effective and efficient wastewater pipeline risk assessment tool for the Hampton Roads Sanitation District, in Virginia, U.S.A. A knowledge based system was developed using an expert system building shell (Xi-Plus).

The system design is based on the knowledge elicited from the experts and literature in sanitary pipeline failure risk evaluation. The knowledge base contains both heuristics and procedural rules. The system interprets the information provided by the user and reasons from that information to reach conclusions on …

Optimum Design For Spring With Orthogonal Design Method, Han Fu - Jie

Tanzania Journal of Engineering and Technology (TJET)

Orthogonal design method is a sort of direct optimum method, by which the op- timal result may be obtained through simple computation and analysis. This method has gained increasingly extensive interest in scientific research, engineering design, end production management as well. The orthogonal table is the basic instrument for carrying out optimum design with orthogonal design method. It is a mathernatical table established On the basis Of the idea of isostatic distribution. As various levels may appear in any column, it makes a partial experiment contain levels of all factors furthermore. RII combina- tions of any two columns may appear …

Development And Testing Of Locally Produced Natural Rubber (Nr) And Pvc Blends, B Mutagahywa

Tanzania Journal of Engineering and Technology (TJET)

The mechanical properties of natural rubber - poly(vinyl chloride) blends have been studied. Tensile and tear strengths of the vulcanizates has been shown to increase with increasing proportions of PVC up to about 20 pphr. Abrasion loss and hardness decreases slightly with increasing concentration of PVC. Increased loading Of carbon black lowers the tensile and tear strength while increasing the abrasion loss and hardness values. This may be explained by the fact that PVC exists as a discontinuous rigid phase in the polymer compound. At normal loading of black (37 pphr) PVC improves processability and acts in the same way …

Antecedents, Moderators And Outcomes Of Organizational Commitment, Beatus Kundi

Tanzania Journal of Engineering and Technology (TJET)

This study examined: (I) the impact of the BtruCturaI of tenure, job integration and organizational support on organizational (2) the mediating roles of the cultural values for performance and collectivity, and the intra—individual factorg of organizational identification and the norm of reciprocity Ln the relationahip between the structural factore and organization coamitment; and, (3) the relationghip between organizational cormitment and the ouecome variablen Of abøeneeeigm, turnover and The Bhow that job and Of the for performance a gignificant facilitator of the effecte Of the etructuraL factors on commitment; and organization identification and the norm of rec are important linkø in …