Digital Commons Network^™

An Evaluation Of The Feasibility Of Neutron Microradiography, Maynard L. Arment

Masters Theses

"The metal working industry has used metallography and microradiography extensively in the past decade. X-ray or gamma microradiography has several advantages as compared to metallography, but a disadvantage concerning alloys of adjacent elements; microradiography cannot distinguish between elements 2 or less atomic numbers apart. Attempts were made using neutron microradiography to distinguish between cadmium and tin rich grains. A maximum resolution of 0.017 inches was found with a calculated possibility of a resolution less than 0.002 inches"--Abstract, page ii.

Study Of Deformation Of Non-Oscillating Droplets In Liquid Media, Arun Kumar Agrawal

Masters Theses

"The object of this investigation was to find a method for predicting the deformation of non-oscillating liquid droplets which are moving in liquid media, from a knowledge of droplet size and the physical properties of the continuous and dispersed phase systems. The deformation of thirteen liquid-liquid systems was experimentally studied in this investigation"--Abstract, page i.

The Shear Graph And Cohesive Soil, Charles Rees Nickerson

Masters Theses

"Some existing test procedures for measuring shearing properties of soils are reviewed. the correlation between the shear strength of two fine-grained soils as indicated by the unconfined compression test and the shear graph test is investigated. This is accomplished by comparing the test results at varying moisture contents and dry densities. One of the soils used is a red plastic clay, the other a silty clay. The test results indicate that for soils wet of optimum the shear graph strength can be taken as being equal to the unconfined compressive strength. This will be conservative for soils that exhibit an …

A Study Of Degradation In The Pumping Of Dilute Polymer Solutions, I-Chung Chang

Masters Theses

"In the course of an investigation of the turbulent flow properties of dilute high polymer solutions in organic solvents, a number of supplementary investigations were required. These were: 1. Determination of the molecular weights of a number of polymers by intrinsic viscosity measurements. 2. Determination of the effect of pumping on the degradation of high polymers in dilute solutions. This included development of a method for estimating the concentration of dilute polymer solutions. 3. Determination of the effects of density, viscosity and non-Newtonian behavior on the calibration of turbine flow meters"--Introduction, page 1.

Temperature Distribution In Thermal Boundary Layers (In Free Convection) Using A Modified Schlieren Method, Philip Ling Chen

Masters Theses

"A simple optical apparatus, the Schlieren interferometer, was constructed for the quantitative investigation of free convection heat transfer from solid bodies. The photographic results, checked by using thermocouples, were used in evaluating the temperature distribution, the key to the solution of these problems. Interpretation of the photographic results was made using the simple calculation for the conventional interferogram and the Dale-Gladstone law. Although the experiments were limited to a heated flat plate and a heated wire, two dimensional test pieces of irregular configuration can be investigated by the same apparatus with simple modifications. The photographs of the conventional Schlieren, the …

An Experimental Analysis Of Transient Vehicle Loads And Response Of Flexible Pavements, John Leonard Sanborn

JTRP Technical Reports

No abstract provided.

The Irish Plumbing And Heating Engineer, January 1965 (Complete Issue)

Building Services Engineering

No abstract provided.

Thin Film Resistor Deposition, Rollie R. Herzog

Masters Theses

"Thin film techniques may be the key to future miniaturization of electrical equipment. The purpose of this thesis was to develop procedures for deposition of thin film resistors and to test these deposited resistors. Starting with a vacuum system, equipment was designed and built to hold and heat the substrate, monitor the substrate temperature and deposited resistance, and to evaporate the material to be deposited. Resistors were deposited and tested for resistance between resistors, capacitance between resistors, and resistance of resistors. A heat aging test was also used comparing resistors with and without a silicon monoxide coating"--Abstract, page ii.

The Cementing Of Hydraulically Placed Tailing Fill By The Oxidation Products Of Pyrrhotite, Stanley H. Alder

Masters Theses

"This thesis has been prepared to make available basic information on the use of the oxidation products of pyrrhotite to cement hydraulic tailing stope fill. As nothing has been published on this subject to date, a review has been made of pertinent information culled from accounts of work in related fields. From this study, a set of equations representing the most likely pyrrhotite oxidation reactions has been evolved and tests supporting these equations performed. Samples of fill, each containing from one to six percent of pyrrhotite, were cemented in the laboratory. They were then examined microscopically, subjected to unconfined compressive …

Matching Of A Horn Antenna To Its Dense Surrounding Media By The Use Of Artificial Dielectric Methods, Paul Arthur Ray

Masters Theses

"The purpose of this thesis is to design an artificial dielectric slug to match a horn in a media such as water and to discuss a method of determining experimentally its dielectric properties. The design is based on known artificial dielectric methods. The method of determining the dielectric properties is by microwave waveguide reflection techniques. This thesis deals with the theoretical aspects and suggests an experimental method of determining the practicability of such a matching method"--Abstract, page ii.

Effects Of Internal Pressure Upon The Buckling Of Thin Circular Cylindrical Shells Under Axial Compression, Leroy E. Thompson

Masters Theses

"An experimental investigation was made of the effects of internal pressure upon the buckling of thin circular cylindrical shells under axial compression. A comparison was made of the experimental and theoretical results; the latter were derived from the large-deflection theory. Results showed that the internal pressure had an appreciable strengthening effect upon the buckling of the cylindrical shell. The comparison showed that the experimental results were lower than the theoretical results for a given internal pressure. The discrepancy between the results can be expected since there were factors not included in the theory: imperfections, end conditions, lengths, and material irregularities"--Abstract, …

Equivalent Circuit Of Unsymmetrical Inductance Diode Using Linvill Lumped Model, Donald Lawrence Willyard

Masters Theses

"Integrated circuit techniques and applications are rapidly changing the electronics industry. A problem common to both state-of-the-art approaches to integrated circuit fabrication is that of miniaturizing and integrating inductors. It is found that, for a certain range of injection current levels, certain unsymmetrically doped junction diodes have an inductive small-signal impedance. This thesis discusses the theory of inductance diodes and applies finite difference equations and the Linvill lumped model to the differential equations that describe their carrier flow processes. The static I-V characteristic and the small-signal equivalent circuit at high injection densities are derived. The elements (R,L,C) of this equivalent …

A Study Of The Photomechanical Effect In Silicon, Ronald M. Oglesbee

Masters Theses

"This paper presents the results of an experimental investigation into the photomechanical effect in silicon. The effect was found to be very similar to the electromechanical effect. In both cases the phenomena observed is the softening of a thin surface layer of the material when it is either illuminated or when a current is flowing through the material. An anisotropy was observed in both the hardness and the photomechanical effect. Increasing temperatures tended to "washout" the photomechanical effect. The surface hardness and the photomechanical effect were found to depend heavily on proper surface preparation of the samples, however little dependence …

The Prediction Of Mix Design Properties For Dense Graded Bituminous Mixtures, Robert Ernest Weeks

Masters Theses

"The purpose of this investigation was to ascertain the feasibility of interpolating values of the physical properties of a dense graded bituminous mix between known values. Also the effects of limestone mineral filler on the properties of a dense graded mix are evaluated. The variables in this study were mineral filler and asphalt cement. Control mixes were established at 2, 6 and 10 percent mineral filler and experimental mixes were prepared at 4 and 8 percent filler. The aggregate consisted of limestone and was mixed with an asphalt cement of 85-100 grade penetration. Al mixes were tested by the Marshall …

Effect Of Single Stirrups On Reinforced Concrete Beams, Vinodbhai T. Patel

Masters Theses

"This study was made to determine the location of vertical stirrups and also to determine the amount of stirrup-steel required to prevent diagonal cracking. The study is limited to rectangular, simply supported, reinforced concrete beams subjected to a concentrated point load at the center of the span. Five sets, each containing three beams were tested. Two sets were cast without stirrups and the results were used to locate the stirrups for the remaining tests. The other three sets were cast with one stirrup on either side of the central load. Stirrups were of the "U" type and formed form No. …

The Design And Construction Of An Instrument For Calibrating Accelerometers, Richard Rabenau

Masters Theses

"The purpose of this work was to design and construct a facility to calibrate accelerometers. A ceramic piezoelectric shaker and modified Michelson interferometer together with necessary electronic equipment were used. The system produced accurate and stable acceleration at five discrete points from 1,000 to 5,000 cycles per second. the maximum calibration levels were approximately 50 g's"--Abstract, page ii.

Optimum Finite Memory Nonlinear Filter, Ching-Chyoun Yang

Masters Theses

"This thesis investigates the possibility of using the Zadah theory and a machine type computer to design an optimum finite memory nonlinear filter for extraction of Poisson distributed signal pulses from a background of Gaussian noise. Basically the procedure involves the technique of solving simultaneous equations by the computer. We demonstrate that it is possible to find the limitation of the filter of class N₁ in terms of an absolute minimum mean square error. However, due to the capacity of the computer we do not actually determine the absolute minimum. Nevertheless we do show that the mean square error decreases …

Stability Determination By Liapunov's Method In Nonlinear Control Systems, Neng-Chung Liao

Masters Theses

"An introduction to Liapunov's second method as it applies to control system stability is presented in this work. Main theorems and definitions of Liapunov's method are treated. In particular, Lur'e's method and Szego's method for testing the stability of a nonlinear system are presented, and several examples are used to illustrate these procedures"--Abstract, page ii.

Use Of Spent Sulphite Liquor For Stabilization Of Fractured Rock And Sealing Off Water Bearing Formations, Laxman Singh Sunda

Masters Theses

"The paper industry, in its process of manufacturing pulp from wood, produces large quantities of a substance called lignin, lignin sulphite, or lignosulphonate. This material has been disposed of as a waste product; however, it does have many potential uses. In this investigation, lignosulfonates were used as agents for bonding rock sections together and, as the chief component of gels, for filling the pores of artificial rock cores. The purposes of these tests were to find how this substance could be used in the mining industry, for stabilizing fractured ground around mine openings and for sealing off water influx into …

Detection Of Stress Corrosion Cracking In U-Bend Brass Specimens By An Electro-Mechanical Method, Floyd Elwin Loftin

Masters Theses

"An apparatus was designed and built which held two u-bend specimens. When the specimens were exposed to a corrodent, losses in strength were detected as a result of stress corrosion cracking. The apparatus was used to study time to failure of cartridge brass u-bend specimens exposed to ammoniacal copper sulfate solutions which varied in pH. A minimum time to failure, 1.06 hours, was detected at pH 7.2. The maximum time to failure, for the range studied, was 28.36 hours at pH 7.7.

No useful data were obtained in the range from pH 6.6 - 6.8. thick, black surface coatings were …

Use Of Kentucky Rock Asphalt For De-Slicking Purposes, James H. Havens

Kentucky Transportation Center Research Report

According to Joe Creason's report appearing in the Courier-Journal June 23, 1957 (copy attached), the Kentucky Rock Asphalt Company elected, June 14, 1957, to liquidate. Among the assets was a stockpile of material which was valued at $197,000 (I recall that the stated price, F.O.B. Sweden, in 1955 was $7.00 per ton); this calculates to be 28,140 tons-- which is a small quantity in comparison to the gross production (200,000 to 275,000 tons; $1.2 to $1.75 million) during some prior years. Apparently 1956 was the last year of sales, and I believe that Kentucky was the sole purchaser. Perhaps as …

The Irish Plumbing And Heating Engineer, October 1964 (Complete Issue)

Building Services Engineering

No abstract provided.

Design Of Regeneratively Cooled, High Temperature, Clean Gas Plasma, Roger Carver Bartlett

Theses and Dissertations

The objective of this thesis was the design of a regeneratively cooled, high temperature, clean gas plasma generator facility. This facility was desired to extend the high temperature research capabilities of the Department of Mechanical Engineering.

Worldwide Training In Air Pollution Control, Harold M. Cota

Civil and Environmental Engineering

A survey of academic training in air pollution control was recently conducted for the APCA Education Council. Questionnaires were sent to faculty at over 200 universities in the United States and 150 universities around the world. This paper lists the schools which completed the questionnaire and includes the number of both undergraduate and graduate courses available, the academic department, and the range of research projects presently underway. The findings indicate that air pollution is a subject being taught worldwide. Most schools predict that their current level of instruction will not change in the next five years. Additions and corrections are …

Thermodynamic Properties Of Perfluoropropane, Frank Fang

Theses

The thermodynamic properties of perfluoropropane (octafluoropropane) have been determined by the author for the saturated region from -100°C to the critical temperature, 71°C. Properties in the superheated region were likewise determined by the author for temperatures from -35°C to 300°C and over a pressure range from 1 atmosphere to 40 atmospheres. Enthalpies, entropies, densities, and specific volumes are reported for both vapor and liquid phases where applicable. The datum point used in these calculations is based on a zero value for vapor enthalpy and vapor entropy at -100°C and 0.0183 atmospheres.

Constants used in the Benedict-Webb-Rubin equation of state were …

Gas Phase Fugacity Coefficients, Harvey Joel Klee

Theses

A method is presented for calculation of fugacity coefficients in gas mixtures. This work is based on a recent paper by Leland, Gamson, and Chappelear, wherein they presented a new method for evaluation of ideal K values. The information required for the method presented here includes pure component physical properties, and generalized tables or equations for compressibility factors, fugacity coefficients, and real gas enthalpy departure terms. Pseudo-critical temperatures and pressures for the mixture are calculated using the expressions presented by Leland and Mueller.

Five different binary systems consisting of paraffin hydro-carbon and CO₂ mixtures containing 318 separate points were …

Interphase Gas-Liquid Mass Transfer Study In A Horizontal Channel, Bruce R. Marx

Theses

The rate of transfer of hydrogen sulfide and of carbon dioxide from an atmosphere of the gas saturated with water to a flowing stream of water in a horizontal channel was investigated over a range of water flow velocities and absolute pressures.

Mathematical models describing the system in terms of the penetration and boundary layer theories were inadequate when used to calculate the diffusivity of each gas in water at various conditions. The results of the hydrogen sulfide-water system study shows a relationship between the diffusivity, the interfacial concentration and the liquid flow rate. The calculated diffusivity of the carbon …

Polypropylene Fibers, Anthony Vincent Galanti

Theses

One of the latest members of the rapidly growing therrnoplastic polymer family which appears capable of successfully competing with the currently saturated textile and chemical markets is polypropylene fiber. The objectives of this Thesis were to: (1) examine the effects of polymer characteristics and fiber processing conditions on the properties of polypropylene fibers, and (2) correlate all existing information on the physical, chemical, and mechanical properties of polypropylene fibers and comparatively evaluate this material with other fibers, natural and synthetic.

Polypropylene is the first member of a new group of polymers prepared by a mechanism defined as "stereospecific" polymerization. From …

Thermal Conductivity Of Solid Materials, Irwin N. Huppert

Theses

A literature search on the methods of determining the thermal conductivity of solids has been made.

A compilation of the various methods of determining the thermal conductivity of solids presented in the literature is given in the report. In general, the literature is lacking in correlations of thermal conductivity with other properties of solid materials. A review of the correlations found is presented. A summary of data presented in the literature is presented in the text.

A method of determining the thermal conductivity of solid materials without measuring the heat flow through the test specimen is presented. The use of …

Esterification Of Oleic Acid With Oleyl Alcohol, Robert Persurance

Theses

The esterification of oleic acid with oleyl alcohol was studied. A literature search showed that the chemical kinetics for this reaction had not been studied previously.

In the temperature range of 150 to 200°C. and up to a conversion of about 85 per cent, the esterification was found to be a second order reaction when the water of reaction was removed from the system by simple distillation.

Para-toluenesulfonic acid is an effective catalyst for this system, and the observed specific rate constant is a linear function of the catalyst concentration.

The effect of temperature on the specific rate constant for …