Digital Commons Network^™

Multi-Objective Border Patrolling Optimization Using Game Theory And Evolutionary Algorithms, Franciso Oswaldo Aguirre

Open Access Theses & Dissertations

Border security has evolved significantly since the days when no more than 75 Mounted Guards patrolled the U.S. border in the early 1900's. The border region includes thousands of miles of both land and maritime borders that must be controlled, as well as commercial transportation networks. One of the primary components of the Department of Homeland Security (DHS) is the U.S. Customs and Border Protection (CBP) agency. One of the most typical activities performed by CBP is patrolling the expansive open areas in between official points of entry (POEs) to prohibit illegal entry attempts. Roving patrols are routinely conducted by …

Cell Releasing System Using Light Responsive Photovoltaic Devices, Mohammod Khairul Kabir Bhuyan

Open Access Theses & Dissertations

Tissue and organ regeneration via transplantation of cell bodies in-situ has become an emerging strategy in regenerative medicine. Injected or implanted cells must be available in large enough numbers and suitable delivery methods must be found especially when implantation into the affected tissue is not possible. In addition, better understanding of how to mitigate the inflammatory reactions and how to degrade the cell carriers are needed. Current cell-based therapies are limited to injection or implantation of cell suspensions or implantation of cell sheets. Development of alternative systems to obtain cell sheets or other functional cellular structures are required. We are …

Utilization Of Carbon Nanofibers Grown On Glass Microballoons (Nmbs) In Point-Of-Care Diagnostic Devices, Emmanuel Gikunoo

LSU Doctoral Dissertations

The use of point-of-care (POC) diagnostic systems holds great promise for the early detection of various diseases. However, detection limits for commercially available POC systems have not been able to meet the lower cutoffs offered by the specialized laboratory testing methods. Research into the use of carbon nanofibers (CNFs) grown on glass microballoons in POC devices was studied. The growth of several millions of the CNFs on each microballoon (NMBs) presented a large surface area with high probability of capturing minute concentrations of biospecies. Functionalization of the NMBs with the carboxyl group needed for biospecies conjugation was achieved by air …

Evaluation Of Triploid Oysters As A Tool To Assess Short- And Long-Term Seafood Contamination Of Oil Spill-Impacted Areas, Martin Scott Miles

LSU Doctoral Dissertations

Many of the organic components of oil have the capacity to persist in the environment, bioaccumulate in tissues, and are toxic to surrounding organisms. Since the early 1970s, environmental assessment programs have utilized bivalves as monitoring tools of chemical contaminants in the marine environment. Because of their sedentary and filter-feeding habit (bioaccumulation), mussels and oysters been employed as sentinel organisms in environmental quality monitoring studies in coastal ecosystems. The use of indigenous (diploid) bivalves for biomonitoring water quality is limited during the summer months due to high stress and changes in biochemical composition induced by reproductive development. In this work …

Polycyclic Aromatic Hydrocarbon Degradation In Tidally Influenced Coastal Marsh Wetland Studied In Laboratory Mesocosm, Doorce S. Batubara

LSU Doctoral Dissertations

The compact mesocosm which was designed for a laboratory scale was used for the kinetic study of refractory organic compounds in a tidally influenced coastal marsh wetland soil. The tidal cycles were controlled pneumatically using an air chamber inside the mesocosm tank. Phenanthrene as the test compound showed that its degradation in the intertidal wetland soil was faster than that in the subtidal wetland soil. Oxygen resupply during the tidal cycles to the intertidal wetland soil would enhance the degradation. Comparison of degradation rates of phenanthrene (Phe), pyrene (Pyr), and benzo[e]pyrene (BeP) were also studied using the mesocosm. The degradation …

The Effects Of Concurrent Driving And In-Vehicle Tasks: A Multivariate Statistical Analysis Of Driver Distraction In A High-Fidelity Driving Simulator, Julius A. Codjoe

LSU Doctoral Dissertations

Distracted driving continues to remain a cause of concern for a number of bodies, including government agencies, traffic safety advocacy groups and law enforcement agencies, because of its traffic safety risks. The driving simulator continues to be popular with researchers in collecting data on performance variables that provide scientific knowledge of the effects of distracted driving. Several of these performance variables can be used to quantify a single distracting effect, resulting in a multivariate dataset. A literature review of related studies revealed that researchers overwhelmingly use univariate (single and multiple) tests to analyze the resulting dataset. Performing multiple univariate tests …

Synthesis And Characterization Of Novel Polyester Scaffolds From Sugarcane Industry By-Products For Use In Skin And Bone Tissue Engineering, Akanksha Kanitkar

LSU Doctoral Dissertations

The aim of this work was to synthesize non-toxic, biodegradable polyesters of aconitic acid, cinnamic acid and glycerol from by-products of the sugarcane industry as scaffolds for skin and bone tissue engineering. Utilizing the by-products, molasses and sugarcane bagasse, not only add value to the cane industry, but also paves path for synthesizing novel bio-based materials from the isolated specialty chemicals. Molasses contain an economically recoverable quantity of aconitic acid and its extraction was studied in detail as a part of this work. The yields of recovered aconitic acid varied from 25–69% depending on the extraction conditions. Under all the …

Image Enhancement Methods And Applications In Computational Photography, Qinchun Qian

LSU Doctoral Dissertations

Computational photography is currently a rapidly developing and cutting-edge topic in applied optics, image sensors and image processing fields to go beyond the limitations of traditional photography. The innovations of computational photography allow the photographer not only merely to take an image, but also, more importantly, to perform computations on the captured image data. Good examples of these innovations include high dynamic range imaging, focus stacking, super-resolution, motion deblurring and so on. Although extensive work has been done to explore image enhancement techniques in each subfield of computational photography, attention has seldom been given to study of the image enhancement …

Less Is More: Long-Term In Vitro Exposure To Low Levels Of Silver Nanoparticles Provides New Insights For Nanomaterial Evaluation, Kristen K. Comfort, Laura K. Braydich-Stolle, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

In view of the vast number of new nanomaterials (NMs) that require testing and the constraints associated with animal models, the majority of studies to elucidate nanotoxicological effects have occurred in vitro, with limited correlation and applicability to in vivo systems and realistic, occupational exposure scenarios.

In this study, we developed and implemented a chronic in vitromodel coupled with lower, regulatory dosages in order to provide a more realistic assessment of NM-dependent consequences and illuminate the implications of long-term NM exposure. When keratinocytes were exposed to 50 nm silver nanoparticles (Ag-NPs), we determined that chronically dosed cells operated …

Remote Beehive Monitoring Using Acoustic Signals, Amro Qandour, Iftekhar Ahmad, Daryoush Habibi, Mark Leppard

Research outputs 2014 to 2021

Recent developments in Wireless Sensor Networks (WSNs) have led to their use in remote data acquisition and automatic data analysis applications, which have proven to be an invaluable tool in a diverse range of fields including biosecurity. Further indications have been found that honeybee health can be monitored and determined through the use of acoustic analysis. In this paper, we present a system that has the ability to remotely detect the presence of pest infestation on a colony of honeybees by comparing the acoustic fingerprint of a hive to a fingerprint of known status. This will aid the goals of …

Novel Syntheses And Surface Modifications Of Electrode Materials For Superior Lithium-Ion Batteries, Jianqing Zhao

LSU Doctoral Dissertations

Rechargeable lithium-ion battery is one of the most promising energy conversion and storage systems that offers high energy and powder densities, long service life and assuring safety. Performance of lithium-ion batteries crucially relies on electrochemical characteristics of electrode materials, i.e., anode and cathode materials. This dissertation work aims at developing novel electrode materials with high capacity, excellent cycling stability and remarkable rate capability for next-generation lithium-ion batteries. The effects of surface modifications for LiMn2O4 cathode materials are studied by depositing ultrathin conformal amphoteric oxides via atomic layer deposition (ALD). In the case of ZnO coating, the thickness of ZnO ALD …

Image-Based Pore-Scale Modeling Of Inertial Flow In Porous Media And Propped Fractures, Yijie Shen

LSU Doctoral Dissertations

Non-Darcy flow is often observed near wellbores and in hydraulic fractures where relatively high velocities occur. Quantifying additional pressure drop caused by non-Darcy flow and fundamentally understanding the pore-scale inertial flow is important to oil and gas production in hydraulic fractures. Image-based pore-scale modeling is a powerful approach to obtain macroscopic transport properties of porous media, which are traditionally obtained from experiments and understand the relationship between fluid dynamics with complex pore geometries. In image-based modeling, flow simulations are conducted based on pore structures of real porous media from X-ray computed tomographic images. Rigorous pore-scale finite element modeling using unstructured …

Biogeochemical Controls On Biodegradation Of Mc252 Crude Oil In Coastal Wetland Systems, Matthew Paul Rodrigue

LSU Master's Theses

Weathering of MC252 oil from the Deepwater Horizon oil spill is taking place in coastal Louisiana marsh and mangrove wetland systems. Alkylated phenanthrenes and dibenzothiophenes, which are the most prominent PAHs found at MC252 contaminated sites, are weathering at rates up to 5% per year relative to alkylated chrysenes 3 years after initial oiling. Flux chambers at marsh locations trapped CO2 that exhibited δ13C signatures lower than indigenous organic matter signifying hydrocarbon mineralization to CO2. Weathering rates at each of these locations are heavily influenced by the biogeochemistry of the surrounding environment. High-resolution nutrient profiles were obtained at different locations …

A Sustainable Remediation Approach For Complete Destruction Of Chloroethanes In Groundwater, Michael Joseph Cheatham

LSU Master's Theses

An up-flow column study was operated in a greenhouse composed of a sand/peat mixed media to investigate the effectiveness of an aerobic zone on the disappearances of chloroethane. The oxygen was supplied by mean of porous Silastic tubing under pressure with a breathing air gas cylinder. Chloroethane was generated via reductive dechlorination of 1,1,1-trichloroethane (TCA) and 1,1-dichloroethane (DCA) in anaerobic bioreactors (ABRs). The columns study was conducted with two duplicate reactors (operated in parallel) that underwent separate perturbations of breathing air introduction. Aqueous samples were collected in 160 mL microcosm bottles and analyzed on a GC equipped with a Flame …

Assimilation, A Biological Nitrogen Removal Strategy For Freshwater Ornamental Fish Hatcheries, Fatemehsadat Fahandezhsadi

LSU Master's Theses

Freshwater ornamental fish production is a major component of aquaculture in the southeastern United States. Closed recirculating aquaculture systems (RASs) allow freshwater ornamental fish hatcheries to mimic native water quality conditions for sensitive species. Total ammonia-N (TAN) removal is the major concern for closed RASs. Biological nitrification is the common method to control TAN. However, the nitrification process might be impaired in acidic water condition with pH<7. Another issue of using the nitrification process for TAN removal is that the nitrification is not sufficient to compensate for the amount of ammonia released in larval production systems because of slow growth rate of nitrifying bacteria. To address these issues, this study suggests an aerobic assimilation strategy in which fast growing heterotrophic bacteria directly convert TAN into microbial biomass. The heterotrophic bacteria needs an external carbon source. This study employed polyhydroxybutyrate (PHB) that is a solid insoluble bioplastic, as a carbon source in the aerobic assimilation process to avoid releasing carbon into the system. In order to understand the applicability of an assimilation process instead of nitrification, this study compared the ammonia-N removal rate by aerobic assimilation biofilters operating @ pH 8 and 6.5 in a batch system. The study also quantified the performance of an aerobic assimilation strategy under different continuous nitrogen loading regimes. This investigation can be used to establish the biofilter air pulsing frequency, which is the optimized air pulsing frequency that avoids clogging in the system. The results showed that there was no apparent release of carbon in the water tank. Unlike nitrification, assimilation strategy for TAN removal was not significantly different in two pH of 8 and 6.5 @ 28 ° C. The average consumption rate of the PHB was found as 21.93± 0.43 grams of PHB consumed per gram of TAN. The results from the continuous system, at a continuous feeding rate of 350 mg-N/d, suggested that the optimum air pulsing frequency through the PHB bed for releasing the excess biosolids was about 6-hour. In general, the study found that the aerobic assimilation using polyhydroxybutyrate (PHB) as a carbon source is an applicable method for ammonia-N removal particularly for freshwater ornamental fish production systems. The drawback against this approach is that the PHB beads are expensive. However, our investigations show that the average cost of the PHB beads have been decreased dramatically during the last few years. This might indicate that the assimilation using PHB beads can be a reasonable choice for ammonia-N removal particularly for freshwater ornamental fish production systems.

Conducting Polymer Nanowires For Multi-Analyte Chemiresistive Sensing, Edward Song

LSU Doctoral Dissertations

A conducting polymer nanowire-based chemiresistive sensor array was developed for the liquid-phase multi-analyte detection. The ability to distinguish and quantify multiple chemical species with a single sensory device can be useful in many areas including food industry, pollution control, biosensors, and explosives detection. A polyaniline nanowire is a good candidate for use as a chemiresistive sensing material due to its large resistivity change and ease of synthesis. However the two most important issues in chemiresistive sensors are the reproducibility in sensing and the selectivity in chemical species. For improving the reproducibility in polyaniline-based chemiresistive sensing, a self-calibration mechanism was proposed. …

Applications Of Cfd Simulations On Studying The Multiphase Flow In Microfluidic Devices, Yuehao Li

LSU Doctoral Dissertations

Microfluidics has been extensively investigated as a unique platform to synthesize nanoparticles with desired properties, e.g., size and morphology. Compared to the conventional batch reactors, wet-chemical synthesis using continuous flow microfluidics provides better control over addition of reagents, heat and mass transfer, and reproducibility. Recently, millifluidics has emerged as an alternative since it offers similar control as microfluidics. With its dimensions scaled up to millimeter size, millifluidics saves fabrication efforts and potentially paves the way for industrial applications. Good designs and manipulations of microfluidic and millifluidic devices rely on solid understanding of fluid dynamics. Fluid flow plays an important role …

Chronic Toxicity Of Nano Metallics On Red Swamp Crayfish (Procambarus Clarkii) In Laboratory And Mesocosm Studies, Jake Andrew Farlow

LSU Master's Theses

Nanotechnology has become integrated in commercial, industrial and medical products, and its use has grown exponentially in the past several years. Although potential applications of nanoparticles (NPs) are numerous, concerns about their water quality, environmental, and human health impacts remain unclear. Crayfish are ubiquitous to streams and wetland habitats, are used as a food source, and inhabit areas that could be impacted by water quality issues. Numerous studies have been conducted on the toxicity of various classes of agricultural pesticides and oils to crayfish (Procambarus clarkii) as a non-target organism. However, there is little evidence published on chronic toxicity of …

Characterization Of Hybrid Electronic Materials Using Atomic Force Microscopy, Madhavi Divakar Rajathadripura

LSU Master's Theses

Miniaturization in the electronics industry has been driven by advancements in material science. Recently, Hybrid Electronic Materials (HEMs) have been postulated to have unique material properties that can be used within the semiconductor industry. As such, the main focus of this research is to characterize the relevant properties of HEMs using atomic force microscopy (AFM), conductive probe atomic force microscopy (CP-AFM), and Raman spectroscopy techniques. Emphasis is placed on characterizing [R6G][TPB] GUMBOS which are a Group of Uniform Materials Based on Organic Salts. GUMBOS exhibit properties such as fluorescence and magnetic susceptibility, both of which may be important with respect …

Method For Synchrotron X-Ray Computed Tomographic Imaging Of Biofilms In Porous Media, Corey Matthew Klibert

LSU Master's Theses

Modeling of biofilms in porous media at pore scale resolution has been hindered by the lack of available experimental techniques to non-destructively image biofilm structure at these resolutions. Researchers have relied upon simulation rather than experimentation to produce pore-scale biofilm models, using simplifying assumptions governing microbial growth such as Monod kinetics and random biofilm seeding locations to generate biofilms in simulated environments. This study investigated the use of absorption-edge synchrotron X-ray computed microtomography (SXCMT) in combination with a contrast agent, Lugol’s iodine solution (10% KI/5% I2), to nondestructively obtain three-dimensional images of biofilms at pore-scale resolution. The study examined and …

A Diagnosis Feature Space For Condition Monitoring And Fault Diagnosis Of Ball Bearings, Ali Kahirdeh

LSU Master's Theses

The problem of fault diagnosis and condition monitoring of ball bearings is a multidisciplinary subject. It involves research subjects from diverse disciplines of mechanical engineering, electrical engineering and in particular signal processing. In the first step, one should identify the correct method of investigation. The methods of investigation for condition monitoring of ball bearings include acoustic emission measurements, temperature monitoring, electrical current monitoring, debris analysis and vibration signal analysis. In this thesis the vibration signal analysis is employed. Once the method of analysis is selected, then features sensitive to faults should be calculated from the signal. While some of the …

Pah Degradation In Wetland Soils As Influenced By Redox Potential, Haoxuan Zhang

LSU Master's Theses

Polycyclic aromatic hydrocarbons (PAHs) are a common contaminant in wetland soils. They are a group of compounds widely distributed in the environment and tend to accumulate in soils. Major contribution to removal of PAHs is biological degradation. For investigating the biodegradation potential of PAHs influenced by tidal actions, equipment was built for simulating the tidal actions, and concentrations of phenanthrene, pyrene, and benzo[e]pyrene were added to the soils samples which were collected from wetland. Experiments were then conducted over 120 days. Redox potentials and PAHs concentrations were measured and analyzed. Results are concluded: 1) influenced by tidal action, phenanthrene, pyrene, …

Mechanical Behavior Of Frp-Confined Self-Healing Concrete, Yueqiang Sui

LSU Master's Theses

This research study is motivated by the need to reduce the costs of maintenance and repair of the aging transportation infrastructure in the US. The proposed approach is to use self-healing concrete. The objective of this study is to test the hypothesis that composite action due to fiber reinforced polymer (FRP) confinement of cylindrical concrete specimens may improve the self-repairing properties of self-healing concrete materials. Sodium silicate (Na2SiO3) is utilized as healing agent in this research. Concrete cylinders with 0.0%, 1.0%, 2.5%, and 5.0% of sodium silicate (SS) by weight of cement were cast and tested to evaluate the effectiveness …

A Study Of Induction Pyrolysis Of Lignicellulosic Biomass For The Production Of Bio-Oil, Charles Edward Henkel

LSU Master's Theses

The increasing demand for energy coupled with a growing concern that the combustion of fossil fuels has on the environment, through the production of greenhouse gases, has created a demand for renewable energy sources. The demand for renewable energy, particularly liquid transportation fuels, can be met in part by the use of biomass based liquid fuels. There are several methods that can be used to produce biomass based fuels, but only thermochemical conversion (pyrolysis) can readily convert lignocellulosic biomass into a fuel-like liquid, bio-oil. The pyrolytic conditions for obtaining maximum liquid yields vary, but many of the criteria can be …

Carbon Nanotube Inkjet Printing For Flexible Electronics And Chemical Sensor Applications, Ryan P. Tortorich

LSU Master's Theses

Carbon nanotubes (CNTs) are becoming a promising new material for use in many fields including the field of electronics. Their mechanical and electrical properties lend themselves to be used in a new generation of electronic devices, namely flexible electronics. Although many deposition methods for carbon nanotubes exist, inkjet printing offers many advantages including superior patterning ability and low-cost fabrication. Presented in this work is the use of inkjet printing in order to deposit carbon nanotubes onto a flexible transparency film. The methods for developing and printing an aqueous single-walled carbon nanotube (SWCNT) ink and an aqueous multi-walled carbon nanotube (MWCNT) …

Bioavailability Of Alpha-Tocopherol Entrapped In Poly (Lactide-Co-Glycolide) (Plga) And Plga-Chitosan Nanoparticles, Lacey Caroline Simon

LSU Master's Theses

Alpha-tocopherol (áT) is a hydrophobic, antioxidant molecule shown to prevent or retard the effects of free radicals associated with diseases. It is hypothesized that the bioavailability of áT can be improved when entrapped in PLGA (Poly lactide-co-glycolide) and PLGA-Chi (PLGA-Chitosan) nanoparticles and that the mucoadhesive properties of chitosan may enhance absorption more than PLGA alone. PLGA and PLGA-Chi NPs synthesized with PVA as surfactant were characterized by measuring entrapment efficiency, size, PDI, and zeta potential when suspended in DI water. Nanoparticle physical stability was evaluated via NP exposure to environmental pH ranging from 2.5-9. Chemical stability of entrapped áT was …

Comparison Of Land Building By Mississippi River Diversion Using One And Two Dimensional Numerical Models, Gyan Prasad Basyal

LSU Master's Theses

River sediment diversions have been identified as one strategy for creating new land and offsetting Mississippi River delta plain land loss. Numerical modeling is one tool for estimating the amount of land, geomorphic features and ecological benefits from diversions. There are a number of models proposed to estimate sediment diversion land building, ranging from simplistic approaches that provide bulk characteristics and use little computational resources to process-based models that require a large amount of input parameters and computing power. This thesis aims to compare and contrast two approaches to simulating the land building processes in a simplified receiving basin: a …

Graphical Models In Characterizing The Dependency Relationship In Wireless Networks And Social Networks, Phuoc Doan Huu Vu

LSU Master's Theses

Semi-Markov processes have become increasingly important in probability and statistical modeling, which have found applications in traffic analysis, reliability and maintenance, survival analysis, performance evaluation, biology, DNA analysis, risk processes, insurance and finance, earthquake modeling, etc. In the first part of this thesis, our focus is on applying semi-Markov processes to modeling the on-off duty cycles of different nodes in wireless networks. More specifically, we are interested in restoration of statistics of individual occupancy patterns of specific users based on wireless RF observation traces. In particular, we present a novel approach to finding the statistics of several operations, namely down-sampling, …

Ultrasonic Pretreatment Of Energy Cane Bagasse For Biofuel Production, Niyaz Ahamed Methrath Liyakathali

LSU Master's Theses

High demand for energy and increasingly expensive petroleum prices led to development of new alternative fuels for transportation, such as bio-ethanol and bio-diesel. Even though a cost reduction in the production of cellulolytic enzymes is occurring, the conversion of plant cellulose into sugars still remains an expensive and slow process. Pretreatment of lignocellulose materials to remove lignin and alter physical/chemical structures significantly improves hydrolysis of cellulose to give high yield of sugars. In this study, ultrasonic pretreatment of energy cane bagasse was used in the presence of ammonia (NH4OH) to enhance the saccharification process by separating lignin, cellulose and hemicellulose …

Empirical Models Of Scalp-Eeg Responses Using Non-Concurrent Intracranial Responses, Komalpreet Kaur, Jerry J. Shih, Dean J. Krusienski

Electrical & Computer Engineering Faculty Publications

Objective- This study presents inter-subject models of scalp-recorded electroencephalographic (sEEG) event-related potentials (ERPs) using intracranially recorded ERPs from electrocorticography and stereotactic depth electrodes in the hippocampus, generally termed as intracranial EEG (iEEG).

Approach- The participants were six patients with medically-intractable epilepsy that underwent temporary placement of intracranial electrode arrays to localize seizure foci. Participants performed one experimental session using a brain-computer interface matrix spelling paradigm controlled by sEEG prior to the iEEG electrode implantation, and one or more identical sessions controlled by iEEG after implantation. All participants were able to achieve excellent spelling accuracy using sEEG, four of the participants …