Digital Commons Network^™

Loss And Dispersion Analysis Of Microstructured Fibers By Finite-Difference Method, Shangping Guo, Feng Wu, Sacharia Albin, Hsiang Tai, Robert S. Rogowski

Electrical & Computer Engineering Faculty Publications

The dispersion and loss in microstructured fibers are studied using a full-vectorial compact-2D finite-difference method in frequency-domain. This method solves a standard eigen-value problem from the Maxwell’s equations directly and obtains complex propagation constants of the modes using anisotropic perfectly matched layers. A dielectric constant averaging technique using Ampere’s law across the curved media interface is presented. Both the real and the imaginary parts of the complex propagation constant can be obtained with a high accuracy and fast convergence. Material loss, dispersion and spurious modes are also discussed.

Modeling The Hydrologic And Particulate Loadings From Paved Urban Surfaces, Chad Michael Cristina

LSU Doctoral Dissertations

This dissertation details the results of recent investigations concerning non-colloidal particulate matter found in urban rainfall-runoff and urban snowmelt. Three forms of the power law model (PLM) were used to model particle number density. It was found that significant model error could be introduced into PLMs when the median diameter particle was used to estimate the number of particles per interval, but the SSE of continuous PLMs could be significantly reduced through the use of correction factors when the sieve interval was large (P<0.05). Additionally, a multiple PLM analysis may be more appropriate than a single PLM analysis when changes in particle population occur within a single gradation. PLMs were also used to model the relationship between cumulative granulometric mass and cumulative particulate-bound metal mass. The use of such calibrated PLMs provided considerable cost reduction when compared to conventional direct measurements of particulate-bound metal mass. A first flush analysis indicated that only events with average volumetric flow rates approaching 1 L/min/m of drainage width exhibit a rapid depletion of particulate matter consistent with the concentration-based definition of the first flush. An analysis of particle separation mechanisms indicated that 90% of these particles, by mass, could be removed from the discharge with detention times of 30 min and 120 min for snowmelt and rainfall-runoff, respectively, in a typical roadside drainage system. It was also found that the kinematic wave model could accurately model significant aspects of rainfall-runoff events in traffic-impacted watersheds provided that abstractions were incorporated into the modeling process. For this watershed the source of abstraction was attributable to vehicular traffic. For high-intensity events with more than 10 vehicles per runoff volume (VPV) the runoff coefficient varied between 0.6 and 0.9 while for low-intensity events with fewer than 10 VPV the coefficient ranged between 0.2 and 0.4.

Primitives And Design Of The Intelligent Pixel Multimedia Communicator, David K. Lucas

Theses: Doctorates and Masters

Communication systems arc an ever more essential component of our modern global society. Mobile communications systems are still in a state of rapid advancement and growth. Technology is constantly evolving at a rapid pace in ever more diverse areas and the emerging mobile multimedia based communication systems offer new challenges for both current and future technologies. To realise the full potential of mobile multimedia communication systems there is a need to explore new options to solve some of the fundamental problems facing the technology. In particular, the complexity of such a system within an infrastructure framework that is inherently limited …

Hdl Implementation Of A Controller Area Network Node, Anthony Richard Marino

Theses and Dissertations

With increasing technology inside automobiles, especially law enforcement vehicles, there is a growing need for centralized wiring and device interconnection methods. Each new technology, such as GPS navigation units and in-vehicle video systems, includes a corresponding wiring harness that needs installation. The summation of all these hardwired technologies leads to large volumes of wire that negatively affect safety, power demands, and future design opportunities. A new trend among automotive manufacturers is to design and implement innovative networks that allow for shared communications between technologies.

This thesis presents the design, development, and implementation of an in-vehicle network that will centralize connections …

Wind Scatterometry With Improved Ambiguity Selection And Rain Modeling, David W. Draper

Theses and Dissertations

Although generally accurate, the quality of SeaWinds on QuikSCAT scatterometer ocean vector winds is compromised by certain natural phenomena and retrieval algorithm limitations. This dissertation addresses three main contributers to scatterometer estimate error: poor ambiguity selection, estimate uncertainty at low wind speeds, and rain corruption. A quality assurance (QA) analysis performed on SeaWinds data suggests that about 5% of SeaWinds data contain ambiguity selection errors and that scatterometer estimation error is correlated with low wind speeds and rain events.

Ambiguity selection errors are partly due to the "nudging" step (initialization from outside data). A sophisticated new non-nudging ambiguity selection approach …

Establishing A Quantitative Foundation For Exactly Constrained Design, Alisha M. Hammond

Theses and Dissertations

Exactly constrained (EC) design is a robust design method which can be used for mechanical assemblies. It entails using the minimum number of constraints to eliminate all desired motion.

While found by some engineers in industry to have many benefits (including robust assembly, no binding or play, ease of assembly, and the ability to tolerate the wear of parts), EC designs remain somewhat unrecognized by academia. One reason for this minimal exposure may be the lack of a quantitative foundation for such designs. This thesis describes the history and current background for EC designs, and it also begins to develop …

Selecting Appropriate Product Concepts For Manufacture In Developing Countries, Danielle Johnson

Theses and Dissertations

There is a noticeable lack of production of indigenously engineered and manufactured products in Less Developed Countries (LDC's). Few products developed in these LDC's could be viable in competitive markets or even sold as components and supplies to other manufacturers of competitive goods. Assumintg that these less developed countries do not innovate and manufacture because they cannot, the next logical question to ask is why can they not?

This thesis looks at the problems of manufacture and design in LDC's from the standpoint of Product Development. It begins by looking at development theories, namely top down and bottom up and …

A Novel Earplug System For Filtering Out Dental Noise, Jiang-Ren Chang, Huan-Kun Cheng, Sheng-Yang Lee, Mingsian R. Bai, Rong-I Lean

Journal of Marine Science and Technology–Taiwan

Undergoing dental treatment is usually a very unpleasant experience for people who have toothaches, especially when they are hurting and there exists some intolerable mechanical noise. To reduce the noise and promote the work efficiency of dentists, a new noisefiltering earplug system with optional music was developed to filter out dental machine noise; if necessary, it can also be adopted as a solution to reduce pain and anxiety of patients during treatments. Furthermore, it can also simultaneously serve as a communication tool between the patient and dentist. In this study, various kinds of noises were initially collected through an off-line …

Alternative Post-Treatment Processes In The Nasa Lunar-Mars Habitat, Sarah Yeldell

Honors Capstone Projects and Theses

No abstract provided.

Rotational Molding Of Acrylonitrile-Butadiene-Styrene Polymers And Blends, Mark Grant Spencer

Theses and Dissertations

The development of acrylonitrile-butadiene-styrene (ABS) resins for use in rotational molding would provide a medium performance material, thus opening doors to new markets for the rotational molding industry. Unfortunately, ABS resins have shown serious problems during the rotational molding process, namely discoloration, bridging, and poor impact strength. It is believed that these effects are due to degradation of the carbon-carbon double bond in the butadiene, through attack by either oxygen or heat. Previous efforts have shown some success in addressing these issues. However, additional improvements are necessary to make ABS resins commercially viable to rotational molders. This study, fourth in …

Satellite Scatterometers: Calibration Using A Ground Station And Statistical Measurement Theory, Peter Kenneth Yoho

Theses and Dissertations

Satellite scatterometers have recently gained popularity due to their unique ability to measure global geophysical data on a daily basis. Increased interest in scatterometry mandates improved design and calibration of these instruments. This dissertation presents new techniques for scatterometer calibration and addresses issues related to the design of future instruments and applications. First, the use of a calibration ground station is considered. A new methodology is established for calibration of SeaWinds, NASA's current scatterometer, using a receive-only ground station. Principles of the methodology are implemented, new analysis techniques developed, and important results obtained for instrument timing, frequency, power, position, and …

Adapting An Effective Interface For A Passive Solar System With A Truncated Pyramid Concentrator, Shirley M. Flinders

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science and Technology at Morehead State University in partial fulfillment of the requirements for the Degree of Masters of Science by Shirley M. Flinders on December 3, 2003.

Hot Melt Inks For Rotogravure-Formulation, Printability And Rheology, Hrishikesh Shreeram Bhide

Masters Theses

A new generation of "Hot melt inks for Rotogravure" was formulated. They melt during heating and reach printable viscosity between 75° C and 130° C, depending on formulation. After printing onto substrate, they solidify. Selections of the best formulations were done based on ink rheology, and print analysis. The formulated inks were also printed on the Moser sheet-fed proofing press .. The rheological data indicated that hot melt inks (without viscosity modifier) have viscosity in the range of 10°-10¹ Poise at 95°C. After printed on a laboratory gravure K-Proofer, the inks showed good reflective density (0.90 - Yellow, 1.30 …

Inside Unlv, Gian Galassi, Katrina Hudak, Carol C. Harter, Eric Sandgren, Tom Hagge

Inside UNLV

No abstract provided.

Water Level Sensor Testing, Stuart Styles, Sarah Herman, Marcus Yasutake, Chuck Keezer

BioResource and Agricultural Engineering

The findings presented here are the continuation of a series of studies begun in 1998 by the Irrigation Training and Research Center (ITRC) at California Polytechnic State University (Cal Poly), San Luis Obispo, California, on behalf of the Mid-Pacific Region of the United States Bureau of Reclamation (USBR) to test water level sensors under a variety of hydraulic conditions. This report is intended as a supplement to the original 1999 report, entitled “Water Level Sensor and Datalogger Testing and Demonstration” (ITRC Report No. R-01010), which describes the testing processes in detail and presents detailed results for the first 17 sensors …

Viewing The Learning Process: Assessment Via Usability Testing, Vicki M. Eller, Steve Eugene Watkins, Richard H. Hall

Business and Information Technology Faculty Research & Creative Works

Learning through Computer-Based Activities Provides a Multi-Modal Approach in Which the User Can Select the Educational Media and Process. Effective Development of These Activities Requires an Understanding of User Interactivity. Traditional Assessment, Such as Test Scores and Subjective Surveys, Looks at End Results and Attitudes. This Method Does Not Monitor the Learning Process. in Particular Developer Needs to Accommodate Diverse Usage Preferences and Choices. Hence, Assessment Should Involve Usability Measures that Are Quantitative and Qualitative. Usability Testing Records Usage Patterns and User Reactions. a Usability Laboratory Was Created at the University of Missouri-Rolla. It is Supplements the Traditional Assessment for …

Color Management Of Desktop Input Devices: Quantitative Analysis Of Profile Quality, Xiaoying Rong

Masters Theses

This thesis investigates the color management principle and input device profiling. The input devices discussed in this thesis are flatbed scanners.

In this thesis, the human visual system, CIE L*a*b* color space, ICC profiles are reviewed, and the evaluation of profile quality is discussed. Grayscale and standard color targets of three primary suppliers are used to create profiles for a scanner. The quantitative analyses of the quality of different profiles, created by two primary commercial profiling software, are conducted according to the Delta-E of the CIE L*a*b* color space. Finally, the relationship of different color targets and profiles for desktop …

Mechanical Properties And Corrosion Resistance Of Ni-Sic Nano Composite Coatings On 2024-T3 Aluminum, Amit Jain

Masters Theses

Coatings of nickel with and without silicon carbide nano-particles were carried out on 2024-T3 aluminum alloy by the electrochemical process. The size of the silicon carbide particles was less than 50nm. Nickel coatings were done using a nickel sulfamate bath maintained at a constant temperature of 50° ± 5° C. Tensile specimens were prepared and studied to determine the Young's modulus of bare aluminum, with nickel coatings and with composite nickel and silicon carbide coatings. Wear samples of 1 inch² (6.45cm²) were prepared and studied for wear resistance. The residual stress measurements were done by the hole …

Modeling The Transient Response Of A Thermosyphon, James Kirk Storey

Theses and Dissertations

Thermosyphon transient operation was numerically modeled. The numerical model presented in this work overcame the limitations of previous studies by including transient conduction in the vessel wall, shear stress between the rising vapor and the falling film in the thermosyphon, the influence of the mass in the liquid pool in the evaporator, and by using a more refined and accurate numerical grid. Unique to this model was the accounting for temporal changes in the effective length of the vapor space due to the expanding and contracting of non-condensable gases in the vapor space. The model assumed quasi-steady one-dimensional vapor flow, …

Bomb-Pulse Chlorine-36 At The Proposed Yucca Mountain Repository Horizon: An Investigation Of Previous Conflicting Results And Collection Of New Data, Klaus J. Stetzenbach, Fred Phillips, Drew Coleman, Don Baepler, Amy J. Smiecinski

Publications (YM)

Previous studies by scientists at Los Alamos National Laboratory (LANL) and the United States Geological Survey (USGS) quantified ³⁶Cl/Cl to test for the presence of fast pathways at the proposed Yucca Mountain high-level nuclear waste repository. The goal of these studies was to determine whether or not fluids containing bomb-pulse ³⁶Cl/Cl traveled along fast travel pathways and reached the repository horizon, however, the two groups followed somewhat different procedures and produced conflicting results. The objective of this study is to attempt to determine the cause of the conflicting results and to obtain additional data to determine whether or …

Thermodynamic Property Prediction For Solid Organic Compounds Based On Molecular Structure, Benjamin T. Goodman

Theses and Dissertations

A knowledge of thermophysical properties is necessary for the design of all process units. Reliable property prediction methods are essential because reliable experimental data are often not available due to concerns about measurement difficulty, cost, scarcity, safety, or environment. In particular, there is a lack of prediction methods for solid properties. Predicted property values can also be used to fill holes in property databases to understand more fully compound characteristics. This work is a comprehensive analysis of the prediction methods available for five commonly needed solid properties. Where satisfactory methods are available, recommendations are made; where methods are unsatisfactory in …

Preliminary Assessment Of Experimental Sophomore Ee Courses, James G. Harris, Kena Burke

Electrical Engineering

In academic year 2001-2002, an experimental yearlong sequence of courses was taught to EE and CPE majors that replaced the traditional circuits and electronics sequence of required courses. The experimental sequence consisted of three quarters, with the first quarter devoted to digital signal processing, and the next two quarters formed from an integrated approach to circuits and electronics. The two sections of students who took the experimental course now are taking the junior year required courses in their major. An assessment is being made to compare the experimental students with a cohort of traditional students. Preliminary results are given for …

A Closed-Form Dynamic Model Of The Compliant Constant-Force Mechanism Using The Pseudo-Rigid-Body Model, Cameron Boyle

Theses and Dissertations

A mathematical dynamic model is derived for the compliant constant-force mechanism, based on the pseudo-rigid-body model simplification of the device. The compliant constant-force mechanism is a slider mechanism incorporating large-deflection beams, which outputs near-constant-force across the range of its designed deflection. The equation of motion is successfully validated with empirical data from five separate mechanisms, comprising two configurations of compliant constant-force mechanism. The dynamic model is cast in generalized form to represent all possible configurations of compliant constant-force mechanism. Deriving the dynamic equation from the pseudo-rigid-body model is useful because every configuration is represented by the same model, so a …

Predicting Drag Polars For Micro Air Vehicles, Mark Elden Luke

Theses and Dissertations

Drag polars for three Micro Air Vehicles (MAVs) were measured at Reynolds numbers of 70,000, 50,000, 30,000, and 10,000 and compared to predictions generated using the classical approach. The MAVs tested had different configurations and aspect ratios varying from 1.2 to 1.6 and ratios of wetted surface area to planform area from 2.6 to 3.9.

A force balance was used to measure the lift and drag on the MAVs at angles of attack ranging from -5 degrees (or -10 degrees) to 10 degrees. The force balance allowed the MAVs to rotate in the pitching axis. The MAV angle of attack …

Reclamation Leaching For Salinity Buildup Under Drip/Micro Irrigation Of Trees, Charles M. Burt, Brett Isbell

BioResource and Agricultural Engineering

ITRC conducted a reclamation leaching experiment in a pistachio orchard in order to quantify the leaching water required to remove salts from the effective root zone of trees. This experiment tested a new reclamation leaching technique - multiple lines of low-flow drip tape were used to apply water to the area of salinity accumulation along a tree row.

Flight Physician - November, 2003, Civil Aviation Medical Association

Browse all Civil Aviation Medical Association Newsletters

A twenty-four page newsletter of the Civil Aviation Medical Association. The newsletter provided news about civil aviation medicine and information related to the organization.

Screw Dislocation Interacting With Twin Interfacial Edge Cracks Between Two Bonded Dissimilar Piezoelectric Strips, Xiangfa Wu, Yuris A. Dzenis, Tian-You Fan

Department of Engineering Mechanics: Faculty Publications

This paper is concerned with the electroelastic potentials and the fracture parameters of a twin-edge-cracked piezoelectric bimaterial strip with a screw dislocation. By means of conformal mapping technique and the known dislocation solution, the antiplane displacement and inplane electric potentials are obtained in closed-form. The intensity factors and the energy release rate are extracted explicitly. In some limiting cases, the present solutions cover those in the literature.

Inside Unlv, Gian Galassi, Cayrn Key, Carol C. Harter, Patrick Ferrillo

Inside UNLV

No abstract provided.

Complying With Florida's Green Land Development Standard: Case Studies And Lessons Learned, Florida Solar Energy Center, Robin Vieira

FSEC Energy Research Center®

The Florida Green Building Coalition, Inc. (FGBC), developed a standard for green land development. It is the first voluntary, non-government standard of its kind to target an entire state. Other groups have created development standards that apply to just a local Home Building Associations (HBA) or a local jurisdiction. The U.S. Green Building Council (USGBC) is beginning a Leadership in Energy & Environmental Design (LEEDTM) for neighborhoods. To comply with Florida's standard, a developer has to earn sufficient points among six categories:

1. Protect Ecosystems and Conserve Natural Resources: for example, surveys, conservation areas, wildlife corridors, wetland preservation and management
2. Circulation: …

Oci-Based Group Communication Support In Corba, Dongman Lee, Dukyun Nam, Hee Yong Youn, Chansu Yu

Electrical and Computer Engineering Faculty Publications

Group communication is a useful mechanism guaranteeing consistency among replicated objects. The existing approaches do not allow transparent plug-in of group communication protocols into CORBA. They either require modification of CORBA or OS, or provide no room for incorporating group communication transport protocols into CORBA. We thus propose a generic group communication framework that allows transparent plug-in of various group communication protocols with no modification of existing CORBA. We extend the open communications interface (OCI) to support interoperability, reusability of existing group communication, and independency on ORB and OS. We also define the group communication inter-ORB protocol (GCIOP) as a …