Digital Commons Network^™

Penetration In Granite By Shaped Charge Liners Of Various Metals, Hemendra Nath Kalia

Doctoral Dissertations

"The penetration in Missouri red granite by cylindrical charges with metal liners of aluminum 2011 (T-3), aluminum 7075 (T-6), yellow brass, monel, maraging steel (vascomax 250), and copper was measured. Metals having high ductility and moderate compressive strength penetrated deeper than high strength maraging steel. Aluminum required a greater standoff for optimum penetration than the other metal liners tested. Preliminary metallographic studies of the liner metals and slugs showed that the grains had elongated along the slug axis. The metals containing zinc formed very small or no slugs. The granite grains were highly fractured. The holes were discolored and coated …

Effect Of Axial Dispersion On Interphase Mass Transfer In Packed Absorption Columns, Virendra Kumar Mathur

Doctoral Dissertations

"A steady state approach was followed in this investigation to determine the effects of liquid and gas flow rates, packing size and packing height on the interphase mass transfer coefficient and gas phase axial mixing Peclet numbers. Experiments were performed on the absorption of carbon dioxide from a mixture of carbon dioxide and nitrogen in a packed column. Absorption was performed using 1/4, 3/8 and l/2 inch Raschig rings, with a packing height of 3 feet and also using 3/8 inch Raschig rings with a packing height of 5 feet. The liquid and gas flow ranges used were 2865 to …

Hydrograph Synthesis For Watershed Subzones From Measured Urban Parameters, Joseph B. Evelyn, V. V. Dhruva Narayana, J. Paul Riley, Eugene K. Israelsen

Reports

An analog computer program was developed to simulate the outflow hydrographs at four locations within the 38th Street Waller Creek urban watershed at Austin, Texas. Actual outflow was gaged at the final outlet of the watershed. This provided a checkpoint for comparing the simulated and observed final outflow hydrographs. The outflow hydrographs for each subzone were obtained by chronologically abstracting interception, infiltration, and depression storage from their precipitation hyetographs. These outflow hydrographs were then routed through Waller Creek channel to obtain the hydrographs at the four desired locations. The advantages of this model are the flexibility in varying the precipitation …

Test 1055: Oliver 1955 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1057: Oliver 1755 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1056: Oliver 1755, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1049: Massey-Ferguson Mf 1150 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1052: Ford 3000 Diesel 6-Speed (All Purpose), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1051: Ford 3000 Gasoline 6-Speed (All Purpose), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1053: Ford 2000 Diesel 6-Speed (All Purpose), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1059: Case 870 Power Shift Gasoline, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1060: Case 870 Manual Gasoline, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1062: Case 1170 And 1175 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Statistical Estimate Of Positional Error Inherent In Very Low Frequency Radio Navigation (Range-Range), Jimmie D. Mcginnis

Masters Theses

"To determine the effectiveness of Very Low Frequency (VLF) navigation in certain areas of the world, it is necessary that a method be developed to estimate the positional error associated with VLF relative positioning techniques. This paper presents a method which consists of a least-mean-squared procedure to sum up the errors contributed by each station being monitored. Since phase jitter (i.e., phase fluctuation) is a random variable, a statistical approach is employed to produce a one Σ ellipse centered about the true position. In short, this method defines the size and orientation of an area called an error ellipse which …

An Approximate Min-Max Solution To The Identification Problem, Richard Loyd Warren

Masters Theses

"A technique based on the min-max error criterion is proposed for identifying a dynamic system in terms of a discrete-time model from the system response to a deterministic input. A linear, single-input/single-output, lumped-parameter, time-invariant (at least during the measurement interval) system is assumed. Although the resulting problem is non-linear, it is shown that linear programming techniques are applicable if a realistic approximation is made. The technique is implemented on the digital computer and evaluated by considering a number of typical discrete-time systems. The effects of additive noise are also considered"--Abstract, page ii.

Light Scattering As A Means Of Probing Particulate Systems, Arwind Krishna Gore

Masters Theses

"The primary purpose of this investigation is to provide basic data needed in determining the size distribution of water-droplets in cloud chambers, sprays, dust clouds, etc. A critique of the classical Mie scattering theory is made to evaluate the influence of the properties such as size, shape and refractive index and of the particulate concentration on the scattering functions. Using He-Ne gas laser radiation of 6328 Å wavelength as the source, the angular intensity functions are tabulated for water-drops up to 20 microns in diameter, dispersed in air at 25ºC. A size interval of 0.2 microns and an angular interval …

Next-State Equation Generation For Asynchronous Sequential Circuits - Normal Mode, Gregory Martin Bednar

Masters Theses

"This paper describes the known methods of generating next-state equations for asynchronous sequential circuits operating in normal fundamental mode. First, the methods that have been previously developed by other authors are explained and correlated in a simple and uniform language in order that the subtle differences of these approaches can be seen. This review is then followed by a development of a new method for generating minimal next-state equations which has some advantages over the previous methods. From the comparison of the previous known methods, it is noted that any one of these methods may be desirable for certain designs …

The Design, Construction And Experimental Verification Of A Split Hopkinson Bar, Woosoon Bai

Masters Theses

"This thesis presents the design considerations for a dynamic loading device utilizing a projectile fired from a tube. Also included is a preliminary investigation of the stress-strain relation, under dynamic loading with the device, for a plaster known as Hydrostone. Design of the unit is based on the split Hopkinson pressure bar originally developed by Kolsky and on a similar unit in use at the Lawrence Radiation Laboratory, Livermore, California. The strain pulses along the pressure bars are sensed by resistance wire strain gages and displayed on an oscilloscope. The oscilloscope traces are photographed and manually digitized for insertion into …

The Dinary Numerical System And Its Applications To Modern Parallel Processing Computers, Hai Chi Koo

Masters Theses

"The Dinary Numerical System (DNS) is an extension of Binary Numerical System. By utilizing the newly developed Large-Scale-Integration technology, DNS can be implemented as a new concept of computer organization which has the merits of parallel processing. DNS consists of three field elements: they are -1, 0, and +1. Since DNS representation is not necessarily unique, new algorithms to generate the number of representations and all equivalent representations are presented in this paper. A Block-Oriented-Computer (BOC) is developed as an array of computing systems. For each of the systems, the arithmetic unit is essentially a modified Digital Differential Analyzer. The …

Numerical Solutions Of The Torsional Oscillations Of A Shaft-Flywheel System, Mahendrakumar Ramkrishna Patel

Masters Theses

"The application of the finite-difference technique, the Fourier transform, and the Laplace transform for the solution of a system governed by the one-dimensional wave equation is examined. A specific example consisting of a continuous shaft-flywheel system acted upon by an exciting torque applied at a specific section of the shaft is studied. The exact solution to this example is obtained using the classical method of superposition of modes, and is used as a reference to evaluate the accuracy (in terms of the rms error) and relative efficiency (based on computer time) of three approximate solution methods. A sinusoidal excitation was …

The Development And Analysis Of A System To Measure Transient Angular Velocity, David Lawrence Persson

Masters Theses

"A measuring system was built to provide a D. C. voltage which was proportional to the angular speed of a particular rotating shaft under question. The measuring system developed has a time constant of approximately .00365 seconds. The final measuring system was developed after trying various other means which proved unsatisfactory. The final device developed would be quite satisfactory in a wide variety of applications"--Abstract, page ii.

An Analysis Of A Synchronization Scheme For 180° Biphase Modulated Signals, James Joseph Spence

Masters Theses

"The problem of analyzing a synchronization system for demodulation of 180° biphase modulated signals is considered in this thesis. The system considered utilizes the so-called squaring loop technique. Techniques derived from the theory of Markov processes are utilized in the analysis of the system. In particular the "fluctuation equation" approach for non-Markovian processes is used. After the analysis of the system is performed, an expression fro the bit error probability is obtained from knowledge of the phase error density function"--Abstract, Page ii.

A Computer Simulation Of The Internal Ballistics Of Recoilless-Rifle Rocket Launchers, John Edd Mosier

Masters Theses

"A computer program has been developed to simulate the basic mechanics and gas dynamics associated with launching a solid propellant rocket from a recoilless rifle. This program, entitled "KICKIT," may be used to predict the performance and evaluate many of the pertinent design parameters of both conventional recoilless rifles and a recoilless rocket launcher system. This program is a valuable analytical tool which enables the designer either to optimize the system design or predict the behavior of the system under off-design conditions"--Abstract, Page ii.

Oxygen Uptake By The Benthal Sludge Of A Waste Stabilization Pond, Edward Landon Niedringhaus

Masters Theses

"This thesis describes the laboratory evaluation of the benthal sludge oxygen uptake of a 6.7 acre waste stabilization pond which has served a city of 2,400 population for a period of seven years. Special emphasis is directed toward the explanation of laboratory techniques developed for this study to measure the oxygen uptake rate. The effects on oxygen consumption of temperature, nature of sludge, initial oxygen tension, and sludge consolidation are discussed. Benthal sludge samples were taken from three locations in the pond. Oxygen consumption studies were conducted in a specially designed plastic cylinder which included a novel magnetic mixing system. …

Evaluation Of City And Region Planning Techniques, Charles Clay Miller

Masters Theses

"The transportation and community planning effort in the United States has resulted in the expenditure of a great deal of time and money. However, the result of this effort has largely been unusable because of a lack of an effective formalized planning method. this thesis presents summarizations of the planning methods employed in ten plans which are typical of the U.S. Planning Effort. Each of these methods are critiqued in the light of a proposed planning method. The Federal Government has recently required the adoption of a Planning, Programming and Budgeting System (PPBS) in an effort to formalize a scientific …

Computerized Methods For Estimating Heating-Cooling-Ventilating System Usage In All-Electric Buildings, Carl William Glaser

Masters Theses

"This thesis develops a method and a resulting computer program for estimating the energy input required by the heating-cooling-ventilating system of a building. The computer program has the ability to model the ventilating system and all the inefficiencies introduced when the heating system is allowed to fight the cooling system to provide temperature control within the conditioned space. The program also can consider mechanical heat reclaim accurately, making the consideration on a time of need versus a time of occurrence basis. The program is written to utilize input data in rather simplified form. This allows the program to be used …

A Study Of Microstrip Transmission Line Parameters Utilizing Image Theory, Joseph Louis Van Meter

Masters Theses

"This paper is a theoretical investigation of the potential, electric field, capacitance, and characteristic impedance of the open strip transmission line or microstrip configuration based upon the classical Thomson Image Technique. It provides the basis for determination of the charge distribution on the strip and reports impedance values which compare favorably both with experimental values and theoretical work in the current literature"--Abstract, page ii.

An Investigation Of The Adjustable Element Concept For Design Of Automotive Exhaust Mufflers, Phillip Scott Gegesky

Masters Theses

"The concept of the adjustable muffler is felt to be a step in the direction of easing the present tedium of constructing and testing prototype mufflers. The evaluation of such a muffler also furthers the knowledge of the interaction of acoustic elements. A review of past and present efforts in the design and evaluation of acoustic filters and filter elements is herein presented. Some consideration is given to phenomena, such as tube attenuation and transverse modes of vibration, which are encountered in muffler evaluation techniques. The characteristics of wave guides are discussed at length. The solution of the plane wave …

Magnetohydrodynamic Channel Flow With Non-Uniform Inlet Velocity Profiles, Gwok-Liang Chen

Masters Theses

"An analysis is made of laminar magnetohydrodynamic (MHD) flow development in the entrance region of a parallel-plate channel. The problem is formulated in general for any velocity distribution at the channel inlet by extending the linearization method of Sparrow, Lin, and Lundgren for non-MHD duct flows. This method involves linearization of the inertia terms in the equation of motion by introducing a stretched axial coordinate. A closed form solution is obtained for the velocity distributions which are continuous across the channel and along the length all the way from the entrance to the fully developed region. An expression for the …

Linear Analysis Of Pneumatic Dashpot Damping, Nathalal Gordhanbhai Patel

Masters Theses

"The linear analysis of pneumatic damping with orifice or capillary restrictions and with or without mean flow is presented. Temperature and pressure relationships are derived from energy considerations rather than the usual simplification of an assumed polytropic coefficient. Analytical results are compared with the experimental results and a coefficient of heat transfer, C_h, is defined for calculation of the equivalent linear damping factor C_d"--Abstract, page ii.