Digital Commons Network^™

Some Concepts On The Use Of Deflection Measurements For Evaluating Flexible Pavements : Technical Report, Richard David Walker, Eldon J. Yoder

JTRP Technical Reports

The use of the methods and the devices (CTL and MRP) are extended to measure moisture content of soil for various other geotechnical purposes. Laboratory compaction mold and Shelby tubes serve as CCs where density are measured using conventional methods

A Study Of The Transient State Of Transpiration Cooling, William C. Wolkenhauer

Masters Theses

"This thesis is a successful attempt to show a new approach to the transpiration cooling problem. Transpiration cooling has long been known as an effective way of removing heat from porous material.

It is shown here that transpiration cooling from a porous material, assuming a temperature difference between the coolant and the porous material, is less effective than where the coolant within the pores is assumed to be at the same temperature as the material adjacent to the pore. Previous investigators made the latter assumption.

The specific problem considered here is that of a uniform, porous plate with constant physical …

Preliminary Study Of An Optimum Vibration Absorber For A Multi-Mass System With Multiple Excitation, John Raymond Burrows

Masters Theses

"The object of this thesis is to demonstrate, by the use of a modern digital computer, a fast, efficient method to eliminate or minimize undesirable stress conditions in a multimass vibrating system with multiple excitation. The condition desired is obtained by the addition of an optimum tuned and damped dynamic vibration absorber, for one critical speed only.

Maximum stress is the criteria used for design here and not amplitude as has been used previously by all other authors.

This solution requires the applied torque to be reevaluated as an average torque and a number of half integer harmonics. This method …

Transpiration Cooling, Herbert S. Brahinsky

Masters Theses

"In the investigation of the problem, it is shown that the process of transpiration cooling is an effective method of cooling. This process may be applied to heat screens or heat shields, as was done in the sample problems worked out here. A porous plate with coolant flowing counter to the flow of heat was used.

The plate temperature is determined by the amount of heat flux, coolant flow, thermal conductivity of the material used as a plate, the specific heat of the fluid, the specific heat of the plate material, the density of the plate material and its porosity. …

An Investigation Of The Factors Influencing The Design Of A Dense Prilled Ammonium Nitrate-Fuel Oil Mixture, Robert Bartley Hopler Jr.

Masters Theses

"The physical characteristics of dense ammonium nitrate prills were examined. The density was found to be 1.52 grams per cubic centimeter, and from this the specific surface was calculated for the size fractions of interest in the investigation. Theoretical loading densities were calculated for between 26.0 and 47.6 percent voids.

The explosive properties of discrete particle size fractions were investigated. The equation by Clark was found to predict the detonation velocity of the sizes smaller than 8/20 mesh. The equation by Cook could not be applied to dense prilled ammonium nitrate. The possibility of a very oxygen negative condition existing …

A Study Of The Concrete Making Properties Of Idealite Lightweight Expanded Shale Aggregate, John J. Ahlskog

Civil Engineering ETDs

Among the many commercially produced lightweight aggregates, Idealite seems to exhibit many desirable qualities. According to the available literature, the expanded shale group of lightweight aggregates are capable of producing concrete with excellent structural characteristics, and one researcher found that expanded shale aggregate produced in rotary kilns resulted in the lowest weight aggregates of the ten groups that he studied.1 While having low creep and shrinkage values, Idealite has been found to give strengths equal to or better than that of conventional sand and gravel concretes.

Idealite concretes are also reported to have excellent workability properties.^

A Discussion On The Durability Of Expanded Shale Aggregate For Exposed Concrete Structures (Bridges), James H. Havens

Kentucky Transportation Center Research Report

During the period between 1924 and 1934, in particular, numerous reinforced concrete bridges were built in Kentucky and elsewhere. Although many of them are still in service, they are some 30 years old and are showing the effects of time and weather. While it is true, of course, that they were constructed without the benefit of air-entrainment and without many present-day control practices, the influences of aggregate quality and freeze-thaw are usually apparent. The advent of the de-icing salt era, about 1940 and following World War II, introduced an additional deteriorating influence gnawing at old and new structures alike. The …

Da Pamphlet 70-5-8, Ussr: Missiles, Rockets, And Space Effort, A Bibliographic Record, 1956-1960, 28 September 1960, Robert Bolin , Depositor

United States Department of Defense Military Intelligence

This manual contains a detailed bibliography concerning the Soviet space program. The appendices contain supplementary information about the Soviet and American space programs.

Statement Of Quartermaster Intelligence Interest, Office Of The Quartermaster General, Department Of The Army, Robert L. Bolin

United States Department of Defense Military Intelligence

According to the forward, the “Statement of Intelligence Interest reflects the over-all interest of the Office of the Quartermaster General in intelligence data and is intended as an aid to persons engaged in the collection, processing, and dissemination of Intelligence. “

In 1960, the Quartermaster Corps was one of the technical services of the Department of the Army. The Army technical services were bureaus providing the Army with supplies, equipment, training, and services. Each was headed by a chief. The Quartermaster General was the chief of the Quartermaster Corps. The Quartermaster Corps was responsible for the procurement, storage, and distribution …

Statement Of Quartermaster Intelligence Interest, August 1960, Office Of The Quartermaster General, Department Of The Army, Robert Bolin , Depositor

United States Department of Defense Military Intelligence

According to the forward, the “Statement of Intelligence Interest reflects the over-all interest of the Office of the Quartermaster General in intelligence data and is intended as an aid to persons engaged in the collection, processing, and dissemination of Intelligence. “

In 1960, the Quartermaster Corps was one of the technical services of the Department of the Army. The Army technical services were bureaus providing the Army with supplies, equipment, training, and services. Each was headed by a chief. The Quartermaster General was the chief of the Quartermaster Corps. The Quartermaster Corps was responsible for the procurement, storage, and distribution …

The Electrochemical Product Of Sodium Meta Periodate, John Joseph Mooney

Theses

An investigation of an electrolytic cell utilizing a nickel anode in alkaline solution for the production of sodium meta periodate from sodium iodate was conducted. The problem was to find an improved method of producing the salts of periodic acid.

The test conditions of cell operation were varied, i. e., temperature, concentration, hydrogen ion concentration, current density and the physical dimensions of the electrolytic cell. The optimum conditions cell operation were found to be a temperature of 21°C, a concentration of 0.10 grams per milliliter of sodium iodate, a pH of 13, current density of between 32 and 42 milliamperes …

Enthalpies And Partial Molal Enthalpies For N-Butane-Nitrogen System, Charles Fisk Paddock

Theses

Enthalpies and partial molal enthalpies are presented for the nitrogen-n-butane system at 340°F. and at pressures from 200 to 10,000 psia. The enthalpies were calculated for the pure components and for five mixtures using a graphical residual method which is described by Van Ness.⁽¹⁾ This method makes use of the Redlich-Kwong equation of state⁽²⁾ to calculate approximate values which are then adjusted by graphical correction factors. This paper illustrates both the advantages and disadvantages of this method, the graphical residual method being advantageous only when the graphical contribution to the total result is relatively small. Calculated enthalpies of …

Particle-Liquid Flow In Vertical Tubes, Frederick John Rowe

Theses

It was the purpose of this investigation to develop an experimental Procedure which would allow the prediction of the variation of fraction void with varying liquid and solid rates from a minimum number of experiments carried out in simple apparatus. This procedure should allow prediction for both smooth and rough particles, and should be valid for several different shapes. The data collected can be plotted on a single chart showing the relation between fraction void, solids throughput, and liquid throughput for all vertical particle fluid systems. Such a method was suggested by Mertes and Rhodes1 in their work developing a …

Power Requirements For Agitation In Fully Baffled Vertical Cylinders, Leo Francis Ryan

Theses

The decrease in power number with increasing Reynolds number sought in this thesis was observed. However, the majority of the data is not an indication of this phenomenon. Only with a relatively high ratio of turbine diameter to vessel diameter could a power number fall-off be obtained. The power number fall-off thus appears to be dependent upon this ratio of turbine diameter to vessel diameter. When the power number fall-off was evidenced, a deep vortex existed despite the presence of full baffling, and large quantities of air were entrained by the liquid.

Even after applying pseudo corrections for both entrained …

Esterification Of Technical Grade Lactic Acid, George John Swier

Theses

A step in the method for manufacturing a purified grade of lactic acid from the technical grade lactic acid (44%) was investigated. In this method, technical grade lactic acid was reacted with normal butyl alcohol, the water formed during esterification was azeotropically removed. The ester formed, was separated from the excess butanol by vacuum distillation. The final step, the hydrolysis of the distilled ester to a purified grade of lactic acid was not covered in this investigation.

In this study, several features are reported, which to the best of knowledge, appear in a publication for the first time. They are …

Thermodynamic Properties Of Methyl Isobutyl Ketone, Lionel James Sirois

Theses

The thermodynamic properties of methyl isobutyl ketone (4-methy1-2-pentanone, hexone) have been determined for the saturated region from 32°F to the critical temperature, 569°F. Properties in the superheated region were determined for temperatures from 200°F to 2000°F and over a pressure range from 5 psia to 1000 psia. Enthalpies, entropies, and specific volumes are reported for both phases where applicable. The datum point for all calculations was zero enthalpy and entropy for a unit mass of saturated liquid at 32°F and 0.083 psia.

Pressure-volume-temperature relations were predicted using the equation of state of Martin and Hou.⁽⁶⁾ This equation of state …

Engineer Intelligence Guide 33, Preparation Of Terrain Diagrams, June 1960, Robert Bolin , Depositor

United States Department of Defense Military Intelligence

In 1960, geographic intelligence in the US Armed Forces was decentralized. The Intelligence and Mapping Division of the US Army Corps of Engineers was primarily responsible for creation of military intelligence concerning the surface of the earth excluding the oceans and seas for the armed forces of the United States. Engineer intelligence guides were issued to provide guidance concerning collection, processing, production, and dissemination of geographic intelligence to elements of the Corps of Engineers.

This engineer intelligence guide explains the differences between maps and terrain diagrams and provides examples using actual maps and terrain diagrams. The maps and terrain diagrams …

Criteria For Design Of Pavement Thicknesses, Kentucky Interstate Highways, William B. Drake, James H. Havens

Kentucky Transportation Center Research Report

The Kentucky Department of Highways, in 1946, sought a more systematic criteria and basis for designing the thickness of bituminous concrete pavements. The Research Division was authorized to pursue this work and to develop the criterion. These efforts were embodied in a report (1) to the Department, which offered a system of design based upon CBR's and EWL's. EWL's were computed originally for a 10-yr. period but this practice was revised in 1954, to encompass 20-yr. traffic (more realistic with respect to average road life). Then, in 1957, the Department requested a re-evaluation of the criteria from the standpoint of …

Behavior Change Through Training, Robert Walter Messerschmidt

Theses

This thesis represents an investigation of attitude and behavior change as a result of human relations training, The elements of heredity and environment are proffered as a basis for attitude and behavior formation. It is denoted that these elements are also instrumental in subsequent development of adult behavior.

As noted in the literature, the term "individual differences" embodies the effect of virtually unique heredity and environmental conditions to which each person is exposed. These differences are also partly determined by the growth in developmental trends, which varies from individual to individual and from time to time.

The existence of individual …

Correlation Of Maximum Air Velocity With Angle Of Installation For Wire Mesh Mist Eliminators, John Lawrence Reid

Theses

Wire mesh entrainment separators were installed in a vertical cylindrical column at varying angles from the horizontal. With a fixed liquid loading, air flow rates were varied in order to determine the maximum capacity of the mist eliminator for any given angle of installation. Mist eliminators studied were 4" thick and constructed of 0. 011" diameter Type 304 stainless steel wire with a density of 12 lbs. per cubic foot and 5 lbs. per cubic foot.

For normal installations of mist eliminators in the horizontal plane, the following equation is used to determine maximum allowable design capacity:

V = K …

Copper Converter: Basic Research Testing With A Plastic Model Converter And Four Types Of Refractories, Arthur C. Bigley Jr.

Bachelors Theses and Reports, 1928 - 1970

In recent years there has appeared an increasing number of papers on converting operations as related to thermodynamics. This approach is a powerful, potential tool. However, the development of new ideas and changes must rely on accurate basic information.

Microradiography Of Metals And Alloys Using A Medical X-Ray Unit, W. R. Byrne

Bachelors Theses and Reports, 1928 - 1970

There is no doubt that the microradiograph technique is of value to the metallurgist. A three-dimensional picture to supplement the photomicrographs should give a true picture of the microstructure. Microradiography can be used where etchants can not differentiate between the various components or where no etchant can be found suitable for a particular alloy.

Secondary Recrystallization In Copper, James E. Thompson

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to study the conditions under which secondary recrystallization will take place in copper. The variables considered were the time annealing, the temperature of annealing, and the degree of cold work undergone by the specimen before it was subjected to the heat treatment.

Cold-Weather Concreting, Milton Evans Jr.

Kentucky Transportation Center Research Report

In order to successfully place concrete in cold weather, certain established requirements must be met. The concrete must not be allowed to freeze, it must not be overheated by artificial means in an attempt to protect it from the cold, and proper curing conditions must be maintained during the period of protection to insure sufficient moisture for the cement to hydrate. Generally, temperatures of not less than 50°F and not more than 90°F are satisfactory. These temperatures must be maintained long enough for the concrete to develop sufficient strength to withstand freezing temperatures and to support the loads. Generally, concretes …

Limestone Fine Aggregate In Portland Cement Concrete, George R. Laughlin

Kentucky Transportation Center Research Report

Limestone is classified as a carbonaceous sedimentary rock. In general, the term is applied only to those rocks in which the carbonate fraction exceeds the non-carbonate fraction. The carbonate may be calcite and/or dolomite. In addition to the primary constituents, there are contaminating minerals such as quartz, clay minerals, chalcedony (chert and flint), pyrite, feldspars and organic matter. The clay minerals are probably the most deleterious contaminates in carbonate rock.

Instructions For Contributors, Academy Editors

Journal of the Arkansas Academy of Science

No abstract provided.

Australian Tractor Tests : No. 30, G. H. Vasey, W. F. Baillie

Journal of the Department of Agriculture, Western Australia, Series 4

THIS Report is taken from the full Technical Report No. 30 of this test; test results are shown here in briefer form: fuller explanations are added.

Values quoted may be rounded out to two instead of three significant figures; to this extent the values may differ slightly but not significantly from those shown in the Technical Report.

Graphs of belt test performance, shown in the Technical Report, are not shown here.

Australian Spark Arrester Tests : Spark Arrester For International B-250, W. F. Baillie, G. H. Vasey

Journal of the Department of Agriculture, Western Australia, Series 4

FORMAL tests on spark arresters are conducted by The Tractor Testing Committee at the Testing Station, Werribee, on behalf of those companies concerned with tractors, engines or spark arresters who wish to have these equipments tested.

Shearing Shed Design, W L. Mcgarry, D. A. Young, M. Butler

Journal of the Department of Agriculture, Western Australia, Series 4

PLANNING the layout of a shearing shed requires a good deal of thought to ensure its maximum working efficiency.

If the contemplated structure is to serve the dual purpose of storage-shearing shed, it is better to plan a shearing shed that can be used for storage, rather than a storage shed with a view to its utilisation as a shearing shed.

A Useful Farm-Made Roller, V E. Western

Journal of the Department of Agriculture, Western Australia, Series 4

A very serviceable compacting roller can be constructed at little expense by using discarded truck tyres.

The roller described here has an overall width of 5 ft. 3 in. and carries seven 9.00 x 24 semi-trailer tyres which had been discarded when the treads were worn smooth.