Digital Commons Network^™

Diffusion Coefficients Of D-Glucose In Aqueous Carboxymethylcellulose And Carboxypolymethylene Solutions, Audrey Liu-Mei Huang

Masters Theses

"A microinterferometric method was used to determine the concentration profiles in the infinite field unsteady state diffusion of D-Glucose in aqueous polymer solutions. Pseudo binary diffusion coefficients were determined as a function of reduced concentration both with and without the effect of liquid volume change during diffusion being considered. The systems studied were D-Glucose in aqueous Carboxymethylcellulose and D-Glucose in aqueous Carboxypolymethylene solutions. Solute concentration ranged from nearly zero to about 9% by weight D-Glucose in the aqueous polymer solutions"--Abstract, page ii.

Coupled Transport Of Heat And Mass In Laminar Tube Flow, Lung-Mau Huang

Masters Theses

"The object of this investigation is to study the mutual dependence of heat and mass transport in laminar and hydrodynamically developed tube flow. Consideration is given to gas flow through a tube whose wall is coated with a sublimable materials so that heat and mass transfers take place between the wall and the flowing gas stream. The tube wall is thermally insulated from the external environment, with the result that the latent heat required by the sublimation process at the wall is supplied solely by convective transfer from the gas. The analysis of the problem requires simultaneous solution of the …

Measurement Of Demagnetizing Factor Of Ring-Core, Subhashchandra Chimanlal Patel

Masters Theses

"A method has been presented to measure the demagnetizing factor of ring-cores. First the incremental apparent permeability and the incremental true permeability were measured at different degrees of saturation and then the demagnetizing factor was determined from those results. The cores used were tape would ring-cores of mean length of 8.0 cm. The method was found suitable for cores with 1/4 mil or thicker tape, but was in question for the 1/8 mil tape core tested"--Abstract, page ii.

A Numerical (Matrix) Solution For The Vibration Frequencies And Modes Of A Nonuniform Rectangular Plate With Arbitrary Edge Conditions, F. David Utterback

Masters Theses

"The material presented in this thesis is designed to provide the practicing engineer with a practical, approximate method of solution for the increasingly important problem of plate vibrations. The technique presented herein is basically an application of the use of generalized coordinates to describe the elastic and inertial properties of a finite element representation of a nonuniform rectangular plate. The plate will be idealized by utilizing a modification of the grid work technique developed by Hrennifkoff as a lattice work of interconnecting beams. By employing the elastic displacements as generalized coordinates, the only required compatibility conditions are that the displacements …

An Experimental Method Of Determining The Thermal Accommodation Coefficients Of Metallic Surfaces, Raymond John Dethorne

Masters Theses

"In the free molecule regime, Knudsen number greater than 10, heat is transferred from a solid by radiation and conduction. The ability of a surface to emit radiant energy is governed by a surface property called emittance while the surface property which apparently regulates the amount of heat transferred by conduction is called the thermal accommodation coefficient. This thesis presents the results of an experimental investigation to determine a relationship between these two properties, emittance and thermal accommodation coefficient. A test apparatus was constructed to measure both the radiation and conduction contributions between two concentric cylinders. cylinders of aluminum and …

Spacing Of Explosive Charges, Calvin J. Konya

Masters Theses

"It is generally believed that the spacing of simultaneously initiated collar primed multiple charges is not dependent on the charge length. The stresses generated by explosive charges have been assumed to propagate through a material in a cylindrical manner. this assumption implied that the stress generated in any plane along the charge diameter would have been uniform in magnitude and direction. A finite explosive velocity along with a conical stress wave causes the stresses near the collar to differ from those farther down the column. for this reason, the spacing of charges would be dependent on charge length. An experimental …

An Intragastric Ph And Motility Monitoring And Automatic Titration System, Barry Foster Maycock

Masters Theses

"Knowledge of the effects of prolonged states of weightlessness on the physiological activities of gastric motility and acid secretion will aid in the planning of future space flights, since aberrations in these activities could affect the performance of astronauts. Investigation of these activities requires monitoring of the pressure and pH in the stomach and titration of the gastric contents. Since previous methods and equipment used for performing these functions are inadequate for this investigation, the equipment whose design and operation are discussed in this thesis was developed. This equipment includes an ingestible sensor capsule which is tethered in the stomach, …

Investigation Of Thermal Resistance At The Interface Of Dissimilar And Similar Metals, Ching-Liang Lin

Masters Theses

"Experiments have been conducted to investigate the resistance and the effect of the directional heat flow at the interface of metals in contact. The test specimens were cylinders, axially aligned and dead weight loaded. Specimen materials were aluminum, bronze, and steel. The tests were conducted at environment pressures of 5x10⁻⁵ Torr. or less. The dead weight load was kept at 10 lbs. for all tests and the surface roughness for all specimens was from 6 to 8x10⁻⁶ inch. The results of the investigation reveal that the resistance to heat flow at the interface of metals decreases as the interface temperature …

Constant Horizontal Force Machining Through Flash Welded Steel Bars Of Varying Hardness, Donald Naeger

Masters Theses

"The purpose of this experiment was to determine the effect of a constant horizontal force applied to the carriage of a lathe as it turned a piece of stock which consisted of two steel bars, of different hardness, flash welded together. This experiment was performed on a lathe to which a pulley system with a mechanical advantage of six was attached to the carriage. The strain on the tool was measured both in the horizontal and vertical directions by a tool dynamometer on which eight strain gages were mounted. The strain gages were calibrated on a Tinius-Olsen testing machine. The …

The Effect Of Prior Cold Work On The Pressure Welding Of Ferritic Nodular Iron, Ronald Morris Ledbetter

Masters Theses

"The purpose of this investigation was to determine the effect of prior cold work by swaging on the pressure welding of ferritic nodular iron. Test pressure welds were produced from continuously cast ferritic nodular iron in the as cast condition and with prior cold work of 20, 30, 40, and 50 per cent reductions in area. Welding pressures of 23,500 psi, 35,300 psi, and 47,100 psi were employed. All welds were made at interface temperatures of 2000°F. Welds made with the as cast material at high welding pressures possessed relatively low tensile strengths due to the creation of planes of …

Design And Construction Of A Liquid Nitrogen Cryostat For Use In A Swimming Pool Type Reactor, Bruce B. Joiner

Masters Theses

"The continued expansion of the nuclear reactor facility and the nuclear engineering program dictates the need that a liquid nitrogen cooled cryostat be available at the reactor. This unit would be available for use in graduate and undergraduate laboratories and for graduate research. A liquid nitrogen cooled cryostat capable of maintaining a sample between 77°K to 80°K for an extended period of time in or adjacent to the core of the reactor was designed, constructed, and successfully operated. Recommendations were made for possible modifications to expand the versatility of the system"--Abstract, page ii.

Analysis Of A Focus Log Electrode In A Non Homogeneous Medium, John Julian Zenor

Doctoral Dissertations

"The mathematical model presented for the focused logging system is applicable to any resistance logging tool of the electrode type. Horizontal or cylindrical resistance interfaces may be included in any combinations. The tool and its environment are compartmentalized, and the integral form of the condition for continuity of current is applied to each compartment. Acceleration methods are applied to the iterative solution of the resulting large-scale system of linear equations. Two specific models are presented, one for the study of the effects of invasion and the other for the study of the effects of bed thickness on the apparent resistivity …

Australian Tractor Test Report No. 49 : Mccormick International 624, G H. Vasey, W. F. Baillie

Journal of the Department of Agriculture, Western Australia, Series 4

AUSTRALIAN TRACTOR TEST REPORT

No. 49 - McCORMICK INTERNATIONAL 624

A Novel Method For Solving The Uniform Distributed Network Analysis Problem, Robert C. Peirson, Edward C. Bertnolli

Electrical and Computer Engineering Faculty Research & Creative Works

An application of the Laplace transform method of Ogata to the solution of the uniform distributed network analysis problem is described. Copyright © 1968 by The Institute of Electrical and Electronics Engineers, Inc.

Recombination Statistics For Neutron Bombarded Silicon Transistors, M. C. Chow, J. L. Azarewiczt, C. A. Goben

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents a recombination statistical model for the neutron-induced base current component reported previously. The derivation was based on the following: 1) the current equation for the induced current component developed previously; 2) the Shockley-Read-Hall statistics for holes and electrons; and 3) the recombination statistics derived by Sah, Noyce and Shockley for sites in the bulk space-charge region. The recombination statistics model depends on the diffusion potential, the junction voltage, the activation energy, temperature, and the ratio of capture cross-sections for holes and electrons. The utility of such a recombination statistical model is illustrated by using measured parameters to …

Radiation And Annealing Characteristics Of Neutron Bombarded Silicon Transistors, L. S. Su, G. E. Gassner, C. A. Goben

Electrical and Computer Engineering Faculty Research & Creative Works

Operating a silicon planar epitaxial transistor in the inverse configuration allows one to demonstrate clearly the importance of the neutron-induced base current component and its degradation of the emitter efficiency, and, because of the much larger depletion layer, to compute a volume dependent damage constant applicable to all silicon p-n junctions. The importance of minimizing the absolute change versus relative change in radiation hardening studies is clearly illustrated. Surface effects were found to be significant for transistors mounted in gas-filled cans. The diffusion potential was predicted, on theoretical grounds, to vary with neutron fluence, and the theory was experimentally confirmed. …

Prediction Of Drag Reduction With A Viscoelastic Model, Gary Kent Patterson, J. L. Zakin

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

Numerical Differentiation Of Equally Spaced And Not Equally Spaced Experimental Data [3], Harry C. Hershey, Jacques L. Zakin

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

W.A. Dairying : Progress In 42 Years, Maurice C. Cullity

Journal of the Department of Agriculture, Western Australia, Series 4

From hardship and elementary standards, West Australian dairying has developed into a consolidated industry with larger herds, increased output and high quality production.

The changes he has seen are reviewed by Mr. M. Cullity who retired last month from the position of Chief of the Division of Dairying, after 42 years of service to the industry.

THE history of Western Australia's dairying industry has been a story of struggle against hardship, marketing problems and adverse criticism.

In spite of this the industry has steadily grown and greatly improved its efficiency.

Interstitial Solute Trapping In Irradiated And Quenched Iron, M. (Manfred) Wuttig, J. T. Stanley, H. K. Birnbaum

Materials Science and Engineering Faculty Research & Creative Works

The interaction of interstitial carbon and nitrogen solutes with defects produced by low temperature neutron irradiation and by quenching was studied in high purity and Ferrovac E iron. Magnetic Dis accommodation techniques were applied to determine the interstitial solute content after irradiation and upon annealing. Doses of about 1017 neutrons/cm2 caused the trapping of about 20 ppm (atomic) interstitial solutes at 65 (carbon) and 40°C (nitrogen). Trapping of carbon in a Ferrovac E iron alloy occurred during a fast quench from 880°C. After trapping, the interstitial solutes reappeared in solid solution at 300 (carbon, neutron irradiation), 200 (nitrogen, neutron irradiation), …

Cutting Nbs Budget, Norbert J. Kreidl

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Current Density-Anodic Potential Curves Of Single Crystal Gaas At Low Currents In Koh, Martin E. Straumanis, J. P. Krumme, William Joseph James

Materials Science and Engineering Faculty Research & Creative Works

Single p-type, GaAs crystals of high purity, Zn doped, were used to determine whether or not the inverse octahedral {111} faces show potential differences and various rates of anodic dissolution. The Ga{111}, As{111}, {110}, and {100} faces, were polished, etched, and etch-polished with concentrated H₂SO₄ + H₂O₂, and immersed in IN KOH. The Ga{111} faces were found to be the most noble with respect to rest and anodic dissolution potentials. The potential difference between the inverse {111} faces was as large as 0.14v for the rest and 0.123v for the dissolution potentials. The …

Zener Disaccommodation In Dilute F.C.C. Co-Ti Alloys, H. B. Aaron, M. (Manfred) Wuttig, H. K. Birnbaum

Materials Science and Engineering Faculty Research & Creative Works

The magnetic Dis accommodation, i.e., the time dependence of the low field magnetic permeability, was investigated in cobalt base alloys containing 0-5.1 at.% (0-4.2 wt.%) titanium in the temperature range 400-700°C. A strong temperature dependence of the Dis accommodation observed in the range 430-530°C could be accounted for predominantly by a single first order relaxation process. Analyzing the data in terms of (a) a single exponential relaxation, (b) a lognormal distribution of relaxation times, and (c) a sum of exponential relaxations, it was shown that the relaxation strength varies as the square of the titanium concentration and that the relaxation …

Age Hardening In A Mg-9 Wt.% Al Alloy, J. Beverley Clark

Materials Science and Engineering Faculty Research & Creative Works

The precipitation process and age hardening mechanism in a Mg-9 wt.% Al alloy were studied principally by transmission electron microscopy. This alloy age hardens by the general precipitation of plates of the equilibrium Mg₁₇Al₁₂ phase on the basal plane of the magnesium solid solution matrix. No evidence for the formation of either G.P. zones or a transition lattice of the Mg₁₇Al₁₂ precipitate was obtained. Cellular precipitation occurs competitively with the general precipitation at nearly all age hardening temperatures. In the solution treated condition, basal slip and {101̄2} twins are the principal deformation modes. Precipitation …

A Metallographic Study Of Solidification And Segregation In Cast Aluminum-Uranium Alloys, Bruce L. Bramfitt, Hollis P. Leighly

Materials Science and Engineering Faculty Research & Creative Works

The micromorphology and type of segregation in vacuum-cast ingots of aluminum-uranium alloys, ranging from 5 to 30 weight percent, were studied. The microstructural characteristics are similar to those of aluminum-silicon alloys of the same composition range, except that the aluminum-uranium eutectic was identified as having "chevron" and "rhombic spiral" types of morphology. © 1968.

Investigations Into Automatic Interpretations Of Terrain Features : Technical Paper, Harold Teddy Rib, Robert Douglas Miles

JTRP Technical Reports

No abstract provided.

Evaluation Of The Performance Of Ultrasonic Equipment For Pavement Thickness Measurements : Progress Report, Charles F. Scholer, Raymond Doran Pavlovich

JTRP Technical Reports

No abstract provided.

A Direct Method Of Measuring Stray Load Loss In Dc Machines, Kanaiyalal R. Shah, George Mcpherson

Electrical and Computer Engineering Faculty Research & Creative Works

Stray load loss in dc machines is denned as the difference between the actual loss under load and the well-recognized loss. This paper describes a simple, reliable, and direct method of measuring this loss by means of a proposed short-circuit test with a correction factor for uncompensated-type dc machines. It also describes the sources and components of stray load losses as they occur under short-circuit test. Copyright © 1968 by The Institute of Electrical and Electronics Engineers, Inc.

A Simple Design Algorithm For Synthesis Of Multilevel Combinational Networks, James H. Tracey

Electrical and Computer Engineering Faculty Research & Creative Works

An algorithm is presented for the synthesis of combinational networks with a constrained arrangement of ANDS, ORS, NANDS, NORS, and inverters. The algorithm is easily presented to students in an introductory logic design course and has considerable application in modern practical logic design. Many texts available for a first course in logic design give very limited practical guidance for synthesis of networks under constraints outlined here. It is suggested that the algorithm presented here be furnished as supplementary material in the introductory course. Copyright © 1968 by The Institute of Electrical and Electronics Engineers, Inc.

Neutron Radiation Damage In Silicon Transistors, C. A. Goben, F. M. Smits, J. L. Wirth

Electrical and Computer Engineering Faculty Research & Creative Works

In the investigation of base and collector current as a function of the emitter-to-base voltage, previous studies have shown that neutron-induced base current has components originating in the emitter space charge region as well as the neutral base region. This study shows that while the low injection level neutron-induced base current is dominated by the space charge component, the high injection behavior appears to be controlled by recombination in the neutral base region. Additional experiments performed in special tetrode transistors and van der Pauw-type samples indicate that changes in collector current are dominated by recombination in the neutral base, while …