Digital Commons Network^™

A Historical Study Of The Influence Of The Railroad Upon Ogden, Utah, 1868-1875, Alma W. Hansen

Theses and Dissertations

The general plan of this study is to sketch the beginning of Ogden settlement and the early history up to the beginnings of the influence of the coming of the railroad, then to follow in more detail the conditions and influences that developed as the railroad was built and the changes that followed the completion of the line.

The Effect Of Composition On Heat Transfer Coefficients For Condensing Binary Vapors With A Single Liquid Phase., James Berwick Todd

LSU Historical Dissertations and Theses

No abstract provided.

Runoff And Soil Moisture, John William Clark Jr.

Masters Theses

"Hydrology is the science treating of water from the time it hits the earth until it leaves the earth. This never ending movement of water is called the "hydrologic cycle" and is best summarized graphically. The hydrologist is primarily concerned with rainfall, runoff and evaporation. One of the basic aims of the science is to compute the surface runoff from any rain on a given area. Surface runoff is here considered as that water which reaches the channels without penetrating the ground, plus subsurface storm flow. Subsurface storm flow is slower than surface runoff but faster than ground water flow. …

The Effect Of Air-Entrainment On Concrete Containing Chert Gravel, Ali Erdogan Dinc

Masters Theses

"The problem which the writer is analyzing in this paper has been suggested to him by Prof. Carlton of the Civil Engineering Department. It consists of two parts.

1. 1. Bar-Run aggregate is to be obtained from Springcreek near Rolla. This material is to be screened and recombined to obtain the best gradation for highest strength concrete obtainable.
2. Durability studies are to be made on the concrete resulting from best established mix by varying the amount of air entrainment compound (Vinsol Resin) to be added to the cement"--Introduction, page 1.

A.C. Circuit Interruption, Palmer L. Anthony Jr.

Masters Theses

"In the last few years the transmission voltages have increased tremendously. Along with the voltage increase came increased load carrying ability for the circuits. The first few links of a new 330 KV transmission system are now under construction in this country. Sweden is already operating a 380 KV line. It is expected to carry a load as high as 850,000 KW on a single circuit.

Interconnection between systems in adjoining areas is a practice to get further operating benefits. The benefits are - reduction of necessary reserve capacity, increased load diversity, and decreasing losses.

Both of these developments bring …

The Holding Strength Of Crimps On Tubes, Aydin Cansever

Masters Theses

"The object of this thesis is to determine by analytical means and laboratory tests the holding force of various crimp methods of fastening sheet metals and special tubing. The study is conducted with heat treated Aluminum alloy 24S.T3.

The problem of joining relatively thin walled tubing of high strength material or the application of a plug to such a tube has been investigated by many manufacturers, but the literature in this field is limited and still there are many cases where a better method may prove very useful. At the suggestion of Dr. Aaron J. Miles, the author decided to …

Crimp Method Of Closure Of Small Pressure Vessels, Zafiri Bersu

Masters Theses

"The object of this thesis is to design a means of closing the ends of thin aluminum alloy tubing in the 1” O.D. to 2” O.D. by .035 to .065 inch thick sizes, so that the closure will withstand internal hydrostatic pressure sufficient to burst the tube along the longitudinal element.

The aim is to approach the ultimate mechanical efficiency possible, and at the same time to keep actual production in mind.…

Summarizing the aims of this investigation, it can be said that the objectives of this investigation are:

1. To design ends for closed vessels.
2. To form the designs.
3. To …

An Investigation Of The Use Of Surface-Active Agents In The Secondary Recovery Of Oil By Water Flooding, Robert P. Schafer

Masters Theses

"The importance of producing oil cannot be emphasized enough in this modem world. Therefore, when primary methods of production seemingly exhaust the oil reservoirs, a secondary method of producing more oil is a necessity. At the present time, secondary methods of oil recovery have developed into a large industry. They are not a new development. The need of introducing compressed air or air-gas mixtures into the wells to increase production was quickly realized. Water flooding methods followed, and at first were restricted to the Eastern fields. Later, about 1935, systematic water flooding methods were developed and applied all over the …

Effect Of Viscosity On The Cetane Number Of A Diesel Fuel, Moris Bolay

Masters Theses

"The object of this paper is to determine or rather experimentally establish the effect of a change in viscosity of a given diesel oil in regard to the ignition quality (cetane rating) of the oil.

The author did not attempt to prove why or find out how much the cetane number was affected. But, merely, tried to experimentally verify the fact that the cetane number of the fuel used underwent a change when its viscosity was decreased by preheating it.

Since his professional interests lie in the field of automotive engineering, several thesis problems were suggested to him by Dr. …

The Lattice Constant And Coefficient Of Expansion Of Chromium, Chao-Ching Weng

Masters Theses

"The most important use of chromium, other than as an alloying element in the manufacture of stainless steel, is for electroplating; to form a coating on other metals for corrosion prevention in order to procure longer life, and to achieve a decorative effect.

The physical properties of chromium are important in the effectiveness of its uses, and its lattice constant, as well as coefficient of thermal expansion, seem worthy of exact determination.

A number of research workers, over a span of thirty years, have spent considerable effort in determining the aforementioned constants. However, their results do not check, and the …

Photoelastic Investigation Of The Stresses In A Capless Connecting Rod, Gerald Delaine Smith

Masters Theses

"For a great many years the primary method used to solve engineering problems was by the use of mathematics. However, rigorous and simple mathematical solutions are only possible if the geometry of the member and its loadings are relatively simple. When irregular shapes with complex loadings are encountered, rigorous mathematical solutions for stresses induced are either impossible or very cumbersome. In such cases, the engineer must resort to other methods which are available today.

This paper attempts to show the application of the photoelastic method to such a problem. Moreover, it will show the comparative ease with which the designer …

The Bloating Of Missouri's Shales, Peter Kurtz Jr.

Masters Theses

"The first objective of this investigation was to determine which deposits of clays, shales, and loesses in Missouri are suitable for use in the production of lightweight aggregate by virtue of their expanding characteristics upon heating. The second objective was to determine, if possible, commercially feasible additions that will produce the bloating property in shales that do not naturally bloat.

There are two conditions which must be met in firing in order to bloat a clay or shale. First, a gas must be formed and evolved during firing. Second, enough glass of the proper viscosity must be formed to trap …

Plastic Deformation Of Rocks, Muhammed Abdul Waheb

Masters Theses

"The purpose of this investigation is to search for a method by which the strength properties of a rock may be described.

For this purpose, an attempt has been made to find out some relationship by which the rooks may be classified or described. For the solution of problems of mine stability, the mechanical properties of a rock should be known, i.e., hardness, toughness and strength. It is difficult to make a study of some method of classification or description of a rock without knowledge of these properties.

With a view to achieve the solution of a general classification for …

Development Of A Test For Rapid Determination Of Octane Ratings Of Gasolines, Charles B. Gangwer

Mechanical Engineering ETDs

For many years, the Mechanical Engineering Department of the University of New Mexico has been interested in developing a more reliable and expedient method to determine octane readings of gasolines than the conventional CFR Motor Method of Test for Knock Characteristics of Motor Fuels. A summary of the development of the conventional CFR Test method and a brief discussion of the operational procedure of this method is necessary to better understand the need for a new fuel rating procedure. To further explain the disadvantages of the conventional test method, an introduction to the new test method to be developed will …

The Design, Construction, And Calibration Of A Stationary Wave Device For Determining Sound Absorption Coefficients Of Acoustic Materials, Douglas W. Ballard

Mechanical Engineering ETDs

The general scope of the thesis investigation is limited to the engineering design and construction of a stationary-wave device for the experimental determination of the sound absorption coefficients of various building materials, the calibration of the apparatus to give comparisons with results obtained in the more expensive reverberation method, and to attempt to correlate observed results with generally accepted acoustical standards.

Protective Refractory Coatings On Titanium Metal, Eugene F. Gibbs

Bachelors Theses and Reports, 1928 - 1970

The problem undertaken in this thesis concerns the development of a newer phase of metallurgy, namely the adaption of the strong, lightweight metal titanium to high-temperature uses. The primary objective of the investigation is to determine wheth­er the application of refractory coatings to titanium will pro­tect the metal from chemical reactions and corrosion at high temperatures.

Some Applications Of Geology To Civil Engineering With Special References To New Mexico And The Southwest, Eldred Ray Harrington

Civil Engineering ETDs

Civil Engineers are usually specialists in some branch of the great field. They often get so deep into the forest that nearby trees effectively obscure the forest as a whole. The same is true of the specialists in the numerous branches of the field of geology. The writer has a certain advantage in this study. Not only has he had approximately equal training in both fields but he has lived almost thirty years as an observer outside the "forest", taking occasional excursions into the thickets of the fields but never staying so long in any one of them that he …

Development Of Electro-Mechanical Equipment For The Measurement Of Knock Characteristics Of Gasolines, Rudolph W. Ebacher

Mechanical Engineering ETDs

It was considered by the writer that characteristics of oscilloscope wave forms representing the varying pressures taking place in the CFR engine cylinder might provide an index to octane ratings of gasoline. Obtaining pressure wave forms on the oscilloscope required some medium for providing an electrical signal in response to engine cylinder pressures. A quartz pressure element was considered as the item that could fulfill this requirement.

Methods Of Routing Floods Through Reservoirs, Rowland W. Fife

Civil Engineering ETDs

Flood routing through reservoirs serves several major functions. It makes possible the determination of the effect of a reservoir, whether constructed for flood control purposes alone or for other purposes, on historic or predicated future floods at the reservoir site. The effect at the dam site then provides a basis for calculating the effect downstream. It also aids in obtaining the proper manipulation of gated spillways on multiple purpose reservoirs to provide the most advantageous flood control on the stream and at the same time make the best use of the water for power, irrigation, or other purposes.

Vapor Pressures & Relative Stabilities Of Certain Double Flourides, Walter L. Gage

Missouri School of Mines and Metallurgy Reports

The vapor pressures and relative stabilities of certain double fluorides such as sodium titanium fluoride and strontium titanium fluoride will be investigated by heating them under vacuum to determine the extent of evaporation or decomposition.

Correlation Of The Model And Prototype Tests Of The Conchas Dam Service Spillway And Stilling Basin, Geary W. Allen Jr.

Civil Engineering ETDs

Conchas Dam and Reservoir, one of the largest water resources projects in the Southwest, build under the supervision of Corps of Engineers, is located below the confluence of the Conchas River and South Canadian River, near Tucumcari, New Mexico. Although it is the source of water supply for the vast Tucumcari Irrigation Project of the U.S. Bureau of Reclamation, its main purpose is flood control. Conchas Dam exerts a tremendous influence on the economy of the northeastern portion of Texas. To a hydraulic engineer its large size and complex hydraulic features present a most challenging field for study and research

Marcasite From The Upper Mississippi Valley Zinc Area As A Source Of Sulphur, Carl R. Christiansen

Professional Degree Theses

"Sulphur is a mineral material which is as basic as steel to our industry and economy. This fact is not generally realized because it is seldom seen, but it goes into the manufacture of practically every article of clothing we wear, and the food we eat is dependent upon it. Most items we produce require the use of sulphur at some stage of their manufacture. The consumption of sulphur has been increasing rapidly and is now far above its World War II peak. Production has been greatly increased but has been unable to keep up with the increasing demand. This …

The Effect Of Various Binders And Moisture Content On The Apparent Thermal Conductivity Of Green Foundry Sand, Robert V. Wolf

Masters Theses

"The broad field of heat transfer is well developed in its theory and mathematics, however, some few applications of varying heat transfer rates have been explored only recently.

Previous to the nineteen-thirties, foundrymen had apparently been interested in heat transfer measurements only from the standpoint of the melting of metals and the heat treatment of the finished castings, with the rate of solidification and the transfer of heat from the casting through the mold being ignored, or at least accepted as an uncontrollable factor. This does not apply, of course, to the use of metal chills to adjust solidification rates …

The Equilibrium Distribution Of Moisture Between Freon-12 And Selected Commercial Desiccants., Arnold Jarvis Gully

LSU Historical Dissertations and Theses

No abstract provided.

Comparative Refining Methods Of A Cane Sugar Solution., Pramod Lal Sarma

LSU Historical Dissertations and Theses

No abstract provided.

Clipper Amplitude Modulator, Durmuş Öcal

Masters Theses

"An amplitude modulated wave is defined as a wave form in which the amplitude of a sinusoidal signal (carrier) is varied in accordance with a modulating signal whose frequency is much lower than the frequency of the carrier signal. Numerous devices have been found for generating an amplitude modulated wave. In some modulators the amplitude of the carrier is actually varied in accordance with the modulating signal. In other types of modulators the carrier and the modulating signal are simultaneously applied to a nonlinear element or circuit. The output of this non-linear element is a distorted wave containing many frequencies. …

Serrated Wire For Welded Wire Fabric, Homer F. Thompson

Masters Theses

"The Wire Reinforcement Institute, Inc., is concerned, primarily, with gathering data and technical information to substantiate the following:

1. That welded wire fabric, when used as a reinforcement in concrete, distributes the stresses throughout the concrete slab, as has been maintained by engineers during the past 40 years.
2. That welded wire fabric provides adequate crack control within the working limits of the fabric.

In order to efficiently accomplish Objectives 1 and 2 above, we wish to establish:

1. The safe working stress that we can safely recommend for welded wire fabric -- both in bond and tension.
2. The proper spacing of longitudinal …

Porosity-Permeability Relationships Of Unconsolidated Sands, Robert Marchel Ponder

Masters Theses

"Unconsolidated sand reservoirs containing oil and gas present difficult problems to the petroleum engineer. Among these problems is that of the determination of the reservoir porosity to facilitate oil and gas reserve and evaluation calculations.

This problem is especially difficult because, to the author's knowledge, no method has been devised to obtain a core sample of the unconsolidated sand that retains the same porosity and permeability characteristics in the laboratory as it had underground. As a result, the petroleum engineer must rely upon empirical methods of calculating the reservoir porosity when the sand is not consolidated.

Many investigators have attempted …

The Effect Of Grain Size On Shearing Strength Of Sand, Keyhan Samimi

Masters Theses

"The object of this study is to determine experimentally the effect of definite grain size on the shearing characteristics of sandy soils. As it will be discussed in detail under the article - The Mechanics of Shear, the shearing characteristics of sandy soils depends on many factors such as grain size and shape, soil structure and relative density, the water content of soil. An attempt is made throughout the entire investigation to determine the effect of definite grain size on the shearing value and the angle of internal friction under the dry and saturated conditions. Furthermore, the results of shear …

A Comparison Of The Real Price And Market Price Of Some Common Metals, Kon-Hock Khaw

Masters Theses

"A number of complex factors influence the fluctuation of the price of a metal. In this investigation, the writer is concerned with the influence of the purchasing power of the dollar and, therefore the difference between the value (real price) and market price of nine metals. That is, this is a study of metal prices and their corresponding values. No attempt is made to analyze the supply and demand of the past or the future, except as they are expressed by their function -- price.

To aid in the comparison, a set of index numbers for metals is compiled and …