Digital Commons Network^™

Effect Of Lime & Cement Additives On The Dynamic Modulus Of Elasticity Of A Clay Soil, Ismail Yolar

Masters Theses

"This thesis is a study to determine the values and characteristics of modulus of elasticity and the modulus of rupture of a clay soil stabilized with lime and cement in an effort to pave the way for including these values in design criteria.

The modulus of elasticity and the Poisson's ratio were obtained by sonic method. Specimens were broken in flexure for modulus of rupture. Experiments were performed with; (1) untreated soil, (2) soil with 4, 6, and 12 percent cement additive, (3) soil with a 3 percent lime additive and 0, 4, 6, and 12 percent cement additive, (4) …

A Study Of The Difference Effects On Alpha Solid Solutions Of Oxygen In Titanium Dissolving In Hydrofluoric Acid, Kuo-Chin Chuang

Masters Theses

"Alpha solid solutions of oxygen in titanium dissolving in hydrofluoric acid exhibited a positive difference effect with k values of 5.7, being independent of the concentration of HF, within the compositional range studied 0 to 5 w/o oxygen. This indicates that various TiO_x alloys are polarizable to the same extent by the same strength of anodic current in hydrofluoric acid.

The difference effect observed on TiO_x alloys dissolving in HF-HCl revealed that the effect is dependent on the oxygen content of the solid solution as well as on the concentration of HCl. The presence of HCl results in …

The Effects Of Sulphur And Copper On Hot-Workability Of Pure Iron, Hung-Chi Chao

Masters Theses

"The independent effects of sulphur, copper and their combinations on the hot-workability of pure iron free from other elements was studied, with special emphasis on the red-short phenomenon. Electrolytic pure iron with the addition of 0.023 cent sulphur, 0.33 per cent copper and 0.024 per cent sulphur plus 0.032 per cent copper along with a heat of only electrolytic pure iron was melted under vacuum, and cast under helium pressure. The specimens machined from the forged bars were tested at various temperatures by the hot twist-test and by the constant energy single blow drop forging test to evaluate the hot-workability …

A Study Of Invert Emulsion Drilling Fluids, Edward R. Tegland

Masters Theses

"Since invert emulsions are being applied as drilling fluids to cope with special drilling and completion problems, evaluations of existing and new types of emulsions are needed. Three types of emulsions are evaluated in this study: (1) type A emulsions prepared with a commercial emulsifier, (2) type B emulsions prepared by adding clay to the external phase, and (3) type C emulsions containing no externally added emulsifier.

Standard testing procedures were used to measure the viscosity and filtration properties of the emulsions studied. Interfacial tension measurements were made using a technique described in the literature. The degree of stability for …

A Systematic Study Of Experimental Parameters In A Cloud Chamber Search For Subionizers, Zin Aung

Masters Theses

"Since there is no theoretical basis for the quantization of electric charge, it is reasonable to consider the possible existence of particles with charges much less than the electronic charge ‘e’. Such particles, if they exist, are expected to ionize more lightly than the electron. Similar remarks hold true for particles with electric dipole moments, and relativistic monopoles with strengths much less than ’e’ electrostatic units. These particles have been termed subionizers.

The selection of apparatus for a subionizer search has been discussed. The desired conditions for such a search using a low background, long sensitive time Wilson cloud chamber …

Evaluation Of Protective Paint Films On Steel By X-Ray Diffraction Techniques, Donald Charles Knobeloch

Masters Theses

"Paints and related organic materials provide the most widely used means of protecting metals against corrosion. While corrosion measurements are based on a full range of quantitative methods in physical and analytical chemistry, the basic problem of evaluation work in the field of paint chemistry has been characterized by empirical testing procedures. Field tests are still of major importance and secondly, the relative value of paints may be predicted through exacting laboratory tests. However, the results of accelerated exposure tests have never successfully been correlated with service experience despite the efforts of many laboratories over a period of 35 years …

An Investigation Of The Factors Influencing The Design Of A Dense Prilled Ammonium Nitrate-Fuel Oil Mixture, Robert Bartley Hopler Jr.

Masters Theses

"The physical characteristics of dense ammonium nitrate prills were examined. The density was found to be 1.52 grams per cubic centimeter, and from this the specific surface was calculated for the size fractions of interest in the investigation. Theoretical loading densities were calculated for between 26.0 and 47.6 percent voids.

The explosive properties of discrete particle size fractions were investigated. The equation by Clark was found to predict the detonation velocity of the sizes smaller than 8/20 mesh. The equation by Cook could not be applied to dense prilled ammonium nitrate. The possibility of a very oxygen negative condition existing …

Analyses Of Two New Electrode Configurations For Earth Resistivity Surveying, Chi-Chao Chang

Masters Theses

"Two new electrode configurations for the electrical resistivity- surveying are introduced: the A-configuration, consisting of a closely spaced pair of current electrodes separated at larger distance from the closely spaced pair of potential electrodes, and the B-configuration, in which each closely spaced pair consists both current and potential electrode. Because electrode pairs can be carried as units, the new configurations can be applied to continuous resistivity surveying more easily than the Wenner configuration....

Theoretical apparent resistivity values are derived, by Maxwell's theory of images, for the A- and B-configuration over a two layered earth using the depth probe method, and …

Scatter Matrix Analysis Of Plane Waves In A Layered Media, Bill W. Ashworth

Masters Theses

"The problem was the application of matrix theory to the solution of the reflection and transmission coefficients for a plane wave incident on a layered media. Background material relating to the problem was reviewed. Equations that were used in the solution of the problem were either derived or explained. The derivations for the reflection and transmission coefficients were carried out in order, starting with the simple case of normal incidence on a junction of two infinite media and progressing through the more difficult case of oblique incidence on a layer of finite thickness separating two infinite media. Scatter matrix analysis …

A Study Of Viscous Frictional Effects And Relay Characteristics On The Operation Of A Positional Relay Servomechanism, Earl F. Richards

Masters Theses

"The thesis describes some experimentally observed data and analytical approaches to the study of a relay servomechanism. The experimental data were secured from an analog simulation of a relay servo system. The results of this data were compared to the transient approach by use of the phase-plane method. The stability of the system was determined using a describing-function. The analytical approaches are described in the presentation.

A study of the effects of viscous friction is described, and the characteristic of the relay used in the system is given special attention. The response to input driving function was considered, and rise …

Transient Temperature Distribution In An Infinite Plate Subjected To Convection And Radiation Heat Exchange, Billy W. Marshall

Masters Theses

"The desired result of this paper is a method of calculating transient temperatures in an infinite plate. The resulting equations are general to the extent possible for aerodynamic heating and radiation boundary conditions. The possible methods of calculation were investigated, and it was felt that a numerical analysis presented the most feasible approach.

Numerical analysis was employed to arrive at a series of equations for calculating the temperatures at selected positions in an infinite plate. A study was then made to determine a method of solving these equations by means of some high speed computing device.

The equations were adapted …

Correlation Of Dust-Count Results By Zeiss Konimeter And Midget Impinger, Chandmal Jain

Masters Theses

"In this modern age, the scientific and technological developments have advanced mechanized mining to the status wherein the attendant dust problems have reached very serious hazard proportions. The significant roles, which have been perfected for the Zeiss konimeter and the midget impinger, in evaluating dust concentrations and thereby revealing possible improvements in making the atmospheric conditions safer, cannot be over emphasized.

While introducing the subject of this paper in the first chapter, the author has presented a historical resume, wherein he pointed out that performances of these instruments have not been correlated in the past. However, the work reported on …

Isothermal Decomposition Of Austenite (In 1.4% Tungsten Steel) At Subcritical Temperatures, Samir Moustafa Riad

Masters Theses

"An experimental investigation was conducted in order to study the relationship between temperature, time and the decomposition of austenite in Tungsten steel of a given composition - and to plot the T-T-T Diagram for this steel.

The steel was prepared, homogenized and cut into identical specimens for further heat treatment and metallographic inspection. Precautions were taken to prevent these specimens from decarburizing during any heat treatment.

This experimental work may be divided into three main parts:-

I. Determination of the critical temperature range; i.e. the range of temperature Ae₁ and Ae₃ above which austenite is stable and below …

Transient Temperature Distribution In Solid Sphere Subjected To Radiation Heat Exchange, William H. Stocklin

Masters Theses

"The author believes that numerical analysis is the most feasible approach to calculating the transient temperature distribution in a solid sphere subjected to various surface conditions; heat flow within the sphere is radial.

Numerical analysis is employed to arrive at a series of equations for calculating the transient temperature at selected points of a solid sphere. A study is made to determine a method for calculating temperatures with these equations; a computing device is found to be the most practical method for this purpose. The equations for temperatures at internal points of the solid sphere are general.

The equations have …

Effect Of Boundary Layer Control, Through Spiral Cuts, On The Film Coefficient Of Convective Heat Transfer, Nicholas W. Barre

Masters Theses

"This thesis is experimental investigation into the possibility of obtaining an increase in the forced convection heat transfer coefficient for a pipe by passing the fluid through a narrow spiral cut in the pipe.

Different spiral pipes with pitches of two, four, eight, ten, sixteen, and twenty inches were used; however, the width of the spiral cut remained unchanged at 3/16 of an inch. Several mass flow rates for water were used up to a maximum of 1536 lbs/hr for each run.

One of the objectives was to find which pitch would give the highest heat transfer rate for a …

A Study Of The Transient State Of Transpiration Cooling, William C. Wolkenhauer

Masters Theses

"This thesis is a successful attempt to show a new approach to the transpiration cooling problem. Transpiration cooling has long been known as an effective way of removing heat from porous material.

It is shown here that transpiration cooling from a porous material, assuming a temperature difference between the coolant and the porous material, is less effective than where the coolant within the pores is assumed to be at the same temperature as the material adjacent to the pore. Previous investigators made the latter assumption.

The specific problem considered here is that of a uniform, porous plate with constant physical …

Preliminary Study Of An Optimum Vibration Absorber For A Multi-Mass System With Multiple Excitation, John Raymond Burrows

Masters Theses

"The object of this thesis is to demonstrate, by the use of a modern digital computer, a fast, efficient method to eliminate or minimize undesirable stress conditions in a multimass vibrating system with multiple excitation. The condition desired is obtained by the addition of an optimum tuned and damped dynamic vibration absorber, for one critical speed only.

Maximum stress is the criteria used for design here and not amplitude as has been used previously by all other authors.

This solution requires the applied torque to be reevaluated as an average torque and a number of half integer harmonics. This method …

The Analysis, Construction, And Calibration Of An Electronic Vibrations Amplifier, Jimmie D. Howard

Masters Theses

"Vibrations analysis necessitates having a device capable of performing some initial phase of detection. The vibration amplifier presented in this thesis performs such an initial aid to analysis by detecting amplitudes of vibrations of varying magnitudes and frequencies. This is accomplished by utilizing a Piezoelectric crystal vibration pickup to obtain an acceleration wave form. Two operational amplifiers perform integrations of the acceleration to obtain displacement. A calibrated meter within the device provides a method of determining magnitudes of displacement. Recording instruments such as the Brush recorder or an oscilloscope may also be used"--Abstract, page ii.

An Analog Method For The Determination Of The Deflection Of Beams Resting On End Supports And Design Of An Automatic Programming Device, Paul C. Jackson Jr.

Masters Theses

"This investigation shows that beam problems can be solved easily and accurately with an analog computer. Two problems were solved as to their shear, moment, slope and deflection along the length of the beam and the graphs drawn by the analog computer were compared with calculated values. Very little difference was found between them.

An electronic programmer was built to aid in handling beam problems as they were being run on the computer. This was capable of putting into the computer bits of data at specified intervals of time. The programmer proved reliable and repeatable once it was adjusted to …

Transpiration Cooling Of A Plane Porous Plate, Raymond George Posgay

Masters Theses

"The transient temperatures were determined in a porous plate for one dimensional heat flow and one dimensional counter coolant flow. One surface of the porous plate was heated by a hot gas by convective heat transfer. A general discussion of the problem is considered and the procedure described for working all such problems dealing with transpiration cooling.

The solution of such problems is illustrated by two examples employing a ceramic plate one inch thick and cooled by a uniform flow of air in a direction counter to the flow of heat, while one surface of the ceramic plate was heated …

Impact Energy Coupling And Impact Seismic Refraction Using Electronic Timing, Roderick D. Carroll

Masters Theses

"The use of impact energy sources in lieu of explosives for shallow seismic investigations is limited chiefly by the low energy available. Means of increasing the energy transmission of an impact source are investigated, using a weight drop arrangement and an oscilloscope. The energy of refracted arrivals is investigated by direct overburden impacts, compaction of the overburden at the point of impact and the use of steel and aluminum plates as coupling devices. Energy transmission is shown to be greatly increased, using a suitable coupling device and the conditions for optimum coupling are discussed. The elastic constants of the ground …

Investigation Of Vertical Internal Spillways, Paul R. Munger

Masters Theses

"This investigation resulted in the development of a means of predicting the discharge of water through an internal spillway type rockfill dam. From the data obtained during the various tests, equations were developed by which the coefficient of discharge for an internal spillway type rockfill dam can be determined when the core height, rock size and head causing flow are known. The equations give results with an error of less than 5%, which is adequate for engineering works"--Abstract, page 2.

Electron Microscope Study Of The Systems Cadmium-Cadmium Chloride And Lead-Lead Chloride, Dennis O'Neill

Masters Theses

"The nature of the dispersed phase in the cadmium-cadmium chloride and lead-lead, chloride systems were investigated with the electron microscope.

Preliminary experiments on preparing and examining the dispersed phase showed that it was most feasible to study the material by electron-microscopic examination of replicas made from the surfaces of the fractured materials. Melting apparatus and methods were chosen so that samples of the melts could be easily quenched to different temperatures and so that the samples could be easily fractured with a minimum of surface contamination. Of the conventional replicating techniques tried, that of carbon replicas pre-shadowed with chromium was …

Apparatus For Inductive-Electromagnetic Model Studies, Won Ho Kim

Masters Theses

"The object of this research is to design, construct and calibrate an apparatus suitable for electromagnetic model studies. A portion of the thesis is devoted to general review and theoretical consideration of electromagnetic prospecting.

Theoretical analysis of electromagnetic survey data by mathematical methods can only be carried out for simple idealized subsurface conditions. Because of the difficulties of theoretical solutions, in contrast to the simplicity of the conditions of similitude in electromagnetic exploration, a model experiment offers a very useful means of studying and comparing the response of naturally occuring conducting mineral bodies.

An apparatus suitable for inductive-electromagnetic model studies …

Some Aspects Of Miscible Phase Displacement As Applied To The Recovery Of Oil Reservoir Crude, David D. Friend

Masters Theses

"Recent application of the miscible sing displacement process as a method to increase recovery from petroleum reservoirs has resulted in a great deal of laboratory investigation, none of which provided conclusive evidence as to the amount of mixing taking place between the displacing and displaced fluids. This investigation attempts to provide a possible insight into the rate and degree of mixing of two fluids with respect to flow path transversed and the rate of advance of the fluids. The laboratory investigation consisted of displacing a fluid from a packed core with another fluid under completely miscible conditions.

Experimental evidence indicates …

Transpiration Cooling, Herbert S. Brahinsky

Masters Theses

"In the investigation of the problem, it is shown that the process of transpiration cooling is an effective method of cooling. This process may be applied to heat screens or heat shields, as was done in the sample problems worked out here. A porous plate with coolant flowing counter to the flow of heat was used.

The plate temperature is determined by the amount of heat flux, coolant flow, thermal conductivity of the material used as a plate, the specific heat of the fluid, the specific heat of the plate material, the density of the plate material and its porosity. …

Deformations And Bending Moments For A Building Slab With A Central Opening, Wu Ping-Yung

Masters Theses

"The adaptability of the classical slope-deflection method analysis to the analysis of uniformly loaded building slab is the subject of this study. The paper demonstrates the use of slope-deflection in computing deflections and bending moments in uniformly loaded square building slabs both with and without central square openings. The results obtained are compared with results of other methods found by other investigators.

Numerous methods have been proposed for use in solving plate or slab problems. The exact solution in the form of a fourth order partial differential equation has proved to be of value in relatively few cases where boundary …

A Vacuum Induction Furnace For Pyrometric Cone Equivalent Determinations, Robert E. Farris

Masters Theses

"Various furnaces which are commonly used for P.C.E. determinations were compared from a literature review. The inadequacies of these furnaces were noted and a furnace was designed, constructed, and evaluated in an effort to minimize or eliminate some of the indicated problems. For this furnace heat is developed in opposed cones (susceptors), which are fabricated from 0.005” molybdenum sheet, by induced (induction) currents from a 10 KW vacuum tube generator. The furnace components are enveloped by a pyrex cylinder in which a vacuum (approximately 1 to 5 micron pressure absolute) is maintained during operation"--Abstract, page ii.

The Effect Of Phosphoric Acid On Compaction And Shear Characteristics Of Pure Kaolin Clay, Bhupat Hargovinddas Mehta

Masters Theses

"The work presented is the investigation of the effect of phosphoric acid on the compaction and shear characteristics of pure kaolin. Pure Georgia kaolin clay average particle size of five microns was mixed with different percentages of phosphoric acid. These mixtures were permitted to react for varying periods of time. The results of the study indicate a notable and gradual increase in dry density of the kaolin with increasing percentages of phosphoric acid admixture. The acid admixture ranges from one up to nine percent of the dry weight of the clay. Increase in cohesion of the clay with increase of …

A Study Of The Energy Dissipation And The Related Pressures And Velocities Of Cylindrical Tank Type Stilling Basin, Graham Wayne Wood

Masters Theses

"In all hydraulic structures that hold back water, whether for the purpose of power, irrigation or flood control, all must have some means of dissipating the energy that is produced by the movement of the water from the pond or reservoir to the tailrace. The method of dissipation depends largely on downstream conditions, terrain and economics. The dissipator is to prevent scour and the undermining of the dam itself. The construction of any type dissipator should be the best one available for the least cost of construction. However, space limitations may dictate another type of dissipator. It has been recommended …