Digital Commons Network^™

Test 519: Harris Four-Wheel-Drive Fdw-C, Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920. Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …

A Fundamental Study Of Clay Drying Using Ware Of Large Cross Section, Robert F. Grady Iii

Masters Theses

"The drying of clay has been studied extensively in the past by many investigators, some of whom attempted to relate this information to the structure of clay and thereby develop a more vivid picture, while others studied the mechanism of drying in its own right in order to present a useable theory that would allow improvements in the drying operation.

At present the literature is unable to present a theory of the mechanism of drying that is sufficiently general to cover the observed aspects of clay drying. Many and varied mechanisms are presented, but correlation is seldom completely evident between …

Horizontal Pressures On Retaining Walls Due To Line Surface Loads, John B. Heagler

Masters Theses

"Among the oldest types of structures with which engineers have had to deal are those which serve to laterally restrain masses of earth, or to prevent earth embankments from assuming their natural angle of repose. This is necessary where space is limited or the natural slope would encroach upon other property. These structures, usually called retaining walls, are subjected to forces, both lateral and vertical due to the pressures exerted by the backfill material and any loads imposed on the backfill material. The first step in the design of the retaining wall is to determine the magnitude, position, and line …

Deposition Of Metallic Coatings From Fused Salt Baths, Andrew Hessler Larson

Masters Theses

"This thesis is the result of an investigation undertaken to study some of the important factors affecting the deposition of metallic diffusion coatings on other metals immersed in a fused salt bath….

There are many methods which have been devised to obtain diffusion coatings on various metals. One which is quite well known and used commercially is the process of “chromizing” which produces a diffusion layer if chromium on another metal. One method of “chromizing” consists of immersing the specimen to be coated in a mixed chloride fused bath containing chromium metal flakes. Another method consists of packing a low …

Corrosion Products Of Titanium In Fused Salt Baths, Kai-Chai Chiou

Masters Theses

"Titanium is gaining great interest in the modern metal industry because of its natural abundance and its desirable physical and chemical properties. Among them, its excellent corrosion resistance, such as the resistance to normal atmosphere attack, humid and saline atmosphere attack, sea water attack, and nitric acid attack, is the most prominent characteristic being welcomed by the engineers. The usefulness of titanium would be greatly increased if it were possible to plate titanium on other metals, thus increasing the corrosion resistance of these other metals.

Much concern, at present, has been given to the possibilities of the electrodeposition of titanium …

Test 528: John Deere Model 70 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920.

Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …

Test 529: International Model Td-24, Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920. Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …

Test 531: Massey-Harris No. 16 Pacer, Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920. Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …

Evaluation Of Sprinkler Irrigation Systems In Northern Utah, Jay M. Bagley, Wayne D. Criddle

Reports

Summary and Conclusions: Sprinkler irrigation will continue to expand in Utah as well as in other irrigated areas of the world. This method of irrigation is suitable to all farm crops grown in the state and to most soils. It is particularly adapted to steep foothill areas where the water supply can be obtained at higher elevation and pumping is not necessary to develop pressure for the sprinkler systems. Also, much of the irrigated land of the state, particularly along the Wasatch front, is owned and operated by "part-time" farmers. Having the water under complete control and the irrigation schedule …

Effect Of Carbon Content In Steels Upon The Deposition Of Titanium From A Fused Salt Bath, Reinhard Paul Abendroth

Masters Theses

"STATEMENT OF PROBLEM Previous work done at the Missouri School of Mines and Metallurgy on the deposition of titanium upon various metals, especially iron and steel, bas shown that titanium can be deposited upon ingot iron and. low carbon steels with comparitive ease. Difficulty was encountered in attempts to deposit titanium upon steels of higher carbon content and upon cast irons.

For this reason, it was decided to investigate more thoroughly the relationship between the carbon content of various steels and the quality of titanium coatings deposited on these steels. Once this relationship had been established, a suitable theoretical explanation …

The Use Of A Steady State Flow Reactor In The Study Of Rapid Gas Phase Reactions, Ormond Kennedy Lay

Masters Theses

"The demonstration of the feasibility of rocket propelled devices for various purposes within the past few years has initiated an intensive search for suitable reactants for use as rocket fuels. Consequently, the investigation of the properties of chemical reactions which rapidly liberate large quantities of energy has assumed major importance. In order that such reactions may be adapted to practical use as rocket propellants knowledge of the characteristics of these reactions is required. Properties such as+ the mechanism of the reaction, the speed of the reaction under varied conditions of temperature, pressure and concentrations, the conditions required for the initiation …

An Investigation Of Continuous Steel Beams In The Plastic Range, Robert Adams Shoolbred

Masters Theses

"The purpose of this thesis is to investigate the action of beams in the plastic range. The test specimen will be a 4WF 13 structural shape continuous over three supports having equal span lengths of seven feet. Three types of loading were chosen. The first loading will be concentrated in the center of each span. The second loading will be a concentrated load in the center of one span only. The third loading will be the settlement of the two end supports until a plastic hinge forms at the center support, then the two spans will be loaded with concentrated …

Testing Of Missouri Shales For Light Weight Aggregate Production, Jerry D. Plunkett

Masters Theses

"The original objective of this investigation was to determine by testing those clays, shales, and loesses occuring in Missouri in large deposits (over 15 feet in thickness with little overburden), which would be suitable for the production of light weight aggregate. The second objective was to investigate the mechanism of bloating as related to the physical and chemical properties of the above materials, and by using these relationships cause clays which do not naturally bloat, to bloat using some addition. The use of additives would permit the economical use of material closer to the market in many instances.

After the …

The Design And Construction Of An Electronic D-C Analog Computer, Frederick R. Wagner, William A. Paar

Masters Theses

"To make this project realizable with the funds available and in the time allowed, and to set forth some definite goals, the following objectives were adopted:

1. Design, construct, and place in working order a d-c electronic analog computer capable of solving 4th order linear differential equations with constant coefficients.
2. Include in the design provisions for real time computation, and also fast, repetitive operation.
3. Provide for later expansion of the computer installation.
4. Limit expenditures to $700"--Introduction, page 4.

A Study Of The Deformation Texture And Its Variation In Cold Drawn Nickel Rods, Krishan Kumar Tangri

Doctoral Dissertations

"The production of rods by cold drawing is a development of recent years as compared to other methods of fabrication. Though a good many investigations correlating the observed mechanical properties to the mill practices employed have been reported, the results nevertheless are more of a qualitative and empirical nature. It is well known that the physical properties of a metal product are related to its deformation textures which are characteristic of the metal and the fabricating method used. Thus a study of the deformation textures of cold-drawn rods, specially by x-ray diffraction techniques should provide a much more precise and …

The Rate Of Dissolution Of Aluminum In Hydrofluoric Acid, Yen-Ngen Wang

Doctoral Dissertations

"Pure aluminum has a relatively low strength, and its use is, therefore, rather limited. However, the resistance of pure aluminum to the attack of acids and many neutral solutions is higher than that of less pure aluminum or most of the aluminum-base alloys. For this reason, alclad alloy sheets, are made with a coating of pure aluminum on one or both sides of an aluminum alloy core. The coating is metallurgically bonded to the core over the entire area of contact. Thus the coating electrochemically protects the core from corrosive attack.

Aluminum is more negative in the electrochemical series than …

Hydrogen Overvoltage On Titanium, Sheng-Tai Shih

Doctoral Dissertations

"The hydrogen overvoltage has been defined as the difference between the potential of the working electrode (cathode) and the theoretical reversible value for the same solution. This definition brings out the difficulty involved in the measurement of the "theoretical reversible potential for the same solution” as the potential of the hydrogen electrode in such a solution is usually different from the value of a standard reversible hydrogen electrode, for which the activity of hydrogen ions is set as being “1” and the potential arbitrarily set as being “0”. Besides, it is sometimes necessary to add addition agents to the solution …

An Investigation Of The Characteristics Of High Alumina Refractory Castables, Gajendra Nath Mohanty

Doctoral Dissertations

"Refractory castables or concretes, a comparatively new member of the refractories family, are an admixture of highly aluminous cements and graded refractory aggregates, blended in predetermined proportions very much like structural concrete. The refractory aggregates must contain a large amount of fines contrary to the requirements of ordinary concrete. Unlike the Portland cements, which are mainly combinations of calcium silicates, the highly aluminous cements are predominantly calcium aluminates. They are comparatively of a refractory natures, having the hydraulic setting property combined also with high early strength. The discovery of the fact that these refractory concretes could be cast, in situ, …

Mechanism And Measurement Of First Stage Graphitization In White Cast Iron, David S. Gould

Masters Theses

"The original object of this thesis was to ascertain if coercive force measurements could be used for the determination of degree of malleablization in malleable iron. Since first stage graphitization was involved, it was only natural that an interest in the mechanism of first stage graphitization developed. The investigation which resulted from this interest was done primarily for the edification of the author, however it was subsequently deemed of enough importance to be included in this thesis. For this reason the thesis may appear at times to deviate from the original objective"--Preface, page iii.

Design Of A Precast Concrete Deck Girder Highway Bridge, Robert V. Gevecker

Professional Degree Theses

"In the Fall of 1951, as a result of an agreement between the Portland Cement Association and the Missouri State Highway Department, with the approval and good wishes of the United States Department of Commerce, Bureau of Public Roads, the State Highway Department embarked on a program to design and construct several precast, prestressed, and precast-prestressed concrete highway bridges"--Introduction, page 1.

The purpose of this extensive program being to indicate to State Highway officials and other interested parties the advantages of these types of construction. In the words of Mr. S. W. O'Brien, District Engineer for the Bureau of Public …

Evaluation Of Traffic Paints In 1953, James H. Havens

Kentucky Transportation Center Research Report

This report documents the performance data obtained by the Research Labratory in connection with field service tests and laboratory tests on traffic paint samples submitted by prospective suppliers for 1954. On the basis of these data and the adjudged performance of the samples offered, invitations to bid will be issued to any or all suppliers offering worthy materials. (See Division of Purchases's Memorandum of January 7, 1953 in Appendix) Winning bidders should be bound by oath to supply the same formulation of materials as furnished in the qualifying samples, and they should be further bound by such tests and analyses …

Report No. 1 On A Water-Bound, Dense-Graded Aggregate Base, Ellis G. Williams

Kentucky Transportation Center Research Report

Favorable experience with dense-graded bases containing calcium chloride created interest in similar mixtures containing only water as a bonding agent. As a result of this interest, a project for base and surface construction was set up on the Phil-Pine Grove Road in Casey County to permit study of this method of base construction. The work was carried out during the period of August to October, 1953.

The pavement, which is 11.62 mi. long, was constructed by contract. It had 2 in. of traffic-bound base (creek gravel) and appeared to be in rather uniform condition with few obviously weak areas. Courses …

Report No. 1 On Vibratory Compaction Of Macadam Base, Ellis G. Williams

Kentucky Transportation Center Research Report

No abstract provided.

Traffic Paint Service Tests For 1954, Kentucky Highway Materials Research Laboratory

Kentucky Transportation Center Research Report

This report documents the performance data obtained by the Research Laboratory in connection with field service tests and laboratory tests on traffic paint samples submitted by prospective suppliers for 1954. On the basis of these data and the adjudged performance of the samples offered, invitations to bid will be issued to any or all suppliers offering worthy materials. (See Division of Purchases's Memorandum of January 7, 1953 in Appendix) Winning bidders should be bound by oath to supply the same formulation of materials as furnished in the qualifying samples, and they should be further bound by such tests and analyses …

Comprehensive City Plan Of Vero Beach, Florida, George W. Simons Jr

City and Regional Planning -- Florida

This report contained a comprehensive city plan to develop and expand Vero Beach, Florida in 1953

Test 515: David Bradley Super Power, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS TEST B: The throttle …

Test 512 Allis-Chalmers Wd-45 Lp Gas, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: Allis-Chalmers WD-45 LP GAS TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear. This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker, point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated. BELT HORSEPOWER TESTS …

Test 511: Allis-Chalmers Wd-45 (Distillate), Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920. Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …

Test 509: Massey-Harris 33-Rt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920. Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …

Test 510: Massey-Harris 44 Special, Nebraska Tractor Test Lab

Nebraska Tractor Tests

This report and any related files are made available to the online through the Lester F. Larsen Tractor Test and Power Museum as resources allow. Established in 1998, this museum is located on the University of Nebraska-Lincoln East Campus. It is and appropriately housed within the walls of the historic 1920 Nebraska Tractor Test Laboratory, where the first tractor test was started on March 31st, 1920. Because the pioneer tests became worldwide standards, this location was designated as a Historic Landmark of Agricultural Engineering by the American Society of Agricultural Engineers in 1980, shortly after testing was moved to a …