Digital Commons Network^™

Small-Scale Solar Central Receiver System Design And Analysis, Daniel Murray

Master's Theses

This thesis develops an analytical model of a small-scale solar central receiver power plant located at the California Polytechnic State University in San Luis Obispo, California at 35.28° N, 120.66° W. The model is used to analyze typical energy output at any time during the year. The power plant is designed to produce an output of 100 kW electrical power, and is supplemented by the combustion of natural gas. Methodologies for determining the proper size and layout of heliostats, optimal tower height, receiver size, and turbine engine selection are developed. In this specific design, solar shares of up to 73.2% …

Viscoelastic Anisotropic Finite Element Mixture Model Of Articular Cartilage Using Viscoelastic Collagen Fibers And Validation With Stress Relaxation Data, Matthew Alexander Griebel

Master's Theses

Experimental results show that collagen fibers exhibit stress relaxation under tension and a highly anisotropic distribution. To further develop the earlier model of Stender [1], the collagen constituent was updated to reflect its intrinsic viscoelasticity and anisotropic distribution, and integrated with an existing mixture model with glycosaminoglycans and ground substance matrix. A two-term Prony series expansion of the quasi-linear viscoelastic model was chosen to model the viscoelastic properties of the collagen fibers. Material parameters were determined by using the simplex method to minimize the sum of squared errors between model results and experimental stress relaxation data of tissue in tension. …

3d Electromagnetic Simulation Tool Exposure For Undergraduate Electrical Engineers: Incorporation Into An Analog Filters Course, Bobby B. Pheng

Master's Theses

With the growth of wireless communications, comes the need for engineers knowledgeable in 3D electromagnetic (EM) simulation of high-frequency circuits. To give electrical engineering students a better understanding of the behavior of electromagnetic fields, experiments including the use of 3D EM simulation software were proposed. Most students get lost in differential equations, curls, and divergences; this thesis aims to remedy that by exposing them to 3D EM simulation, which may motivate them toward further study in electromagnetics. Also, experience using EMPro is very beneficial for future RF/microwave/antenna engineers, as use of 3D EM simulation is becoming a requirement for this …

Predictive Musculoskeletal Simulation Using Optimal Control: Effects Of Added Limb Mass On Energy Cost And Kinematics Of Walking And Running, Antonie J. Van Den Bogert, Maarten Hupperets, Heiko Schlarb, Berthold Krabbe

Mechanical Engineering Faculty Publications

When designing sports equipment, it is often desirable to predict how certain design parameters will affect human performance. In many instances, this requires a consideration of human musculoskeletal mechanics and adaptive neuromuscular control. Current computational methods do not represent these mechanisms, and design optimization typically requires several iterations of prototyping and human testing. This paper introduces a computational method based on musculoskeletal modeling and optimal control, which has the capability to predict the effect of mechanical equipment properties on human performance. The underlying assumption is that users will adapt their neuromuscular control according to an optimality principle, which balances task …

The Effects Of Concentration, Stir Rate, And Processing Temperature On The Iridescence Of Polymethyl Methacrylate Nanoparticles, David Baruela

Materials Engineering

Synthetic opals were synthesized by creating polymethyl methacrylate (PMMA) nanospheres in order to determine which conditions would create the best iridescent samples. The factors affecting the iridescence were nanosphere concentration, stir rate, and processing temperature. PMMA solutions were made by adding 17 mg of granular azobis to a solution of 16 mL of distilled water with 3 mL of methyl methacrylate (MMA). The solution was stirred at different rates, slow and fast, and different temperatures, 70 °C and 90 °C, under a constant flow of nitrogen gas for 40 minutes until the polymerization reaction was complete. Glass substrates were prepared …

Development Of A Protocol To Measure Gene Expression In The Mouse Tibia, Daniel Hoover

Biomedical Engineering

Numerous molecular factors active in bone tissue direct fracture repair and remodeling which can be altered by disease conditions such as Peripheral Arterial Disease (PAD) and Osteoporosis. Methods of molecular biology are commonly applied to investigate the expression and role of these molecular factors. This project presents a robust three-step protocol for examining gene expression in the mouse tibia. The protocol begins with isolating RNA from a flash frozen tibia sample. The isolated RNA is reverse transcribed into cDNA. Finally, PCR is performed to indentify expressed genes. Establishing this protocol will allow further research into the mechanisms of bone remodeling …

Mac's Fiesta: A Foreign Language Game For The Sifteo Platform, Karina Cordon

Computer Engineering

Mac’s Fiesta is a Spanish learning game designed on the Sifteo gaming platform for children ages four and up. The Sifteo gaming platform provides a new way of interacting with computers by giving users a set of tangible and interactive cubes. Each Sifteo cube has a clickable colored screen and can sense motion and adjacent blocks. Games on this platform are designed to encourage the development of core thinking skills. This project aims to explore how Sifteo cubes can be used for language learning as well as observe how effective they are as educational tools.

Riley The Cat, Nicholas Zankich

Computer Engineering

There are many toys that exist that are comfort objects. Generally these are toys that are soft such as blankets, stuffed animals, and pillows. Robotic toys also exist such as games, interactive books, and instruments. There exists a crossover market that includes Furbys, Tomagachi pets, and Fur Real Friends. While being very popular, I believe that this crossover isn’t perfect, and that there is a lot of room for improvement. Riley (Figure 1) was created to make something that is both completely a robot and a comfort object.

Barrel Racer's Calculator, Hollie Kucera

Electrical Engineering

Barrel racing is a rodeo event in which a horse and rider attempt to complete a clover-leaf pattern around preset barrels in the fastest time. This sport combines the horsemanship skills of a rider and the horse’s athletic ability to safely and successfully maneuver around the three barrels (three fifty-five gallon metal drums) placed in an arena.

In barrel racing, the purpose is to make the run as fast as possible. An electric eye and timing system keep track of the time. The time starts when the horse and rider cross in between the electric eyes and ends when the …

Phase Splitter Guitar Effects Pedal, Jerry Gough

Electrical Engineering

The goal of this project was to create a unique type of guitar distortion effects pedal. The initial plan was to use a Hilbert Transformer, also called a Phase Splitter, to produce a vibrato type distortion. Later during the circuit design phase, it appeared that a tremolo effect could be easily implemented in addition to the vibrato. Both the tremolo and vibrato effects were implemented in the final design. Although there are many different types of vibrato and tremolo pedals already in existence, it does not appear that any current designs use a Hilbert Transformer or phase splitter. Hopefully, this …

Music Driven Graphical Visualization System, Glenn Bruner

Electrical Engineering

In today’s society, we are able to enjoy listening to music on an assortment of high-tech devices such as home computers, or multimedia players, or personal audio players. A common characteristic of typical audio media players is that they lack the ability to provide visual stimulation in addition to the provided audio stimulus. Large public events, such as concerts, could be enhanced if they included visual effects in addition to audio stimulation. The goal of this project is to provide a graphical visualization that is automatically synchronized to an audio signal with a goal of enhancing the overall musical experience. …

Foce Intermodule Communications System, Roland Quiros

Electrical Engineering

Done in conjunction with Chad Kecy of the Monterey Bay Aquarium Reasearch Institute (MBARI), this project is an expansion of the Free Ocean Carbon Emission (FOCE) project. This iteration created a communications protocol between the different modules in an expandable array of PIC24-based boards.

Patterns For Success: Women In Technology: Analyzing Top Technical Women For Repeated Mindsets, Life Experiences, And Career Navigation, Julie L. Gill

Honors College Theses

The purpose of this thesis is to discuss and discover why some women are so successful in the computing fields when public opinion continues to hold that computing is not a women’s field because there are so few women in computing. The roots for this shortage begin in theAmerican educational system, “Nationwide only about 20 percent of the bachelor's degrees incomputer science go to women,” according to a November 11, 2011 NPR story titled “Addressing the Shortage of Women in Silicon Valley”. This shortage is well noted and heavily researched, Plausible solutions have been proposed and it is critically important …

A Kinetic Study Of Anti-Vegf-A Polyclonal Antibodies And Anti-Vegf-A Ssdna Aptamers, Heather A. Hedeen

Master's Theses

A new detection reagent that could possibly augment or replace antibodies research and diagnosis methods are aptamers. Aptamers are ssDNA, RNA or polypeptide constructs that function like active antibodies. Antibodies and aptamers both specifically bind to selected target molecules, and as such they enable the detection or targeting of the presence or absence of a specific antigen.

In order to ensure that ssDNA aptamers perform similarly to antibodies, anti-VEGF-A polyclonal antibody and anti-VEGF-A ssDNA aptamer were evaluated against vascular endothelial growth factor A (VEGF-A) using Surface Plasmon Resonance (SPR). It was hypothesized that the anti-VEGF-A aptamer had the same, if …

Novel Platform Development Using An Assembly Of Carbon Nanotube, Nanogold And Immobilized Rna Capture Element Towards Rapid, Selective Sensing Of Bacteria, Elizabeth I. Maurer, Kristen K. Comfort, Saber M. Hussain, John J. Schlager, Sharmila M. Mukhopadhyay

Chemical and Materials Engineering Faculty Publications

This study examines the creation of a nano-featured biosensor platform designed for the rapid and selective detection of the bacterium Escherichia coli. The foundation of this sensor is carbon nanotubes decorated with gold nanoparticles that are modified with a specific, surface adherent ribonucleic acid (RNA) sequence element. The multi-step sensor assembly was accomplished by growing carbon nanotubes on a graphite substrate, the direct synthesis of gold nanoparticles on the nanotube surface, and the attachment of thiolated RNA to the bound nanoparticles.

The application of the compounded nanomaterials for sensor development has the distinct advantage of retaining the electrical behavior …

Esem Analysis Of Mice Femurs With Varying Sost Levels, Patrick K. Mcclay

Biomedical Engineering

This project’s goal was to analyze the properties of the cortical femur on 100 mice bones from Lawrence Livermore National Laboratory. Analysis was limited to imaging which determined the ratio of bone volume to total volume (BV/TV) and osteocyte lacunae density. Mice were altered to knock out their SOST gene: a negative regulator of bone formation. Twelve groups were created to differentiate their treatment, duration, and phenotype. Transgenic (TG) mice had an overexpression of the SOST gene: they carried a bacterial artificial chromosome. Mice with limb defects (DEF) were the offspring of two TG mice and carried twice the amount …

Corrosion Of Stainless Steel 316l And Astm F75 Cobalt Chromium Alloy During Immersion Testing In Silver Salt Solutions, Meagan Higgins

Materials Engineering

This study evaluates the potential effects of silver salts on biocompatible metals used for prostheses during the chemical reduction process to produce a silver antimicrobial layer on the metal’s surface. Samples of two biocompatible metals were obtained: Stainless Steel 316L and ASTM F75 Cobalt Chromium Alloy. Three different silver salts were also acquired: silver nitrate, silver sulfadiazine, and silver chloride. Specimens of each metal were cut to size using a 4-1/2 inch aluminum oxide, 40 grit, cut off wheel for metal, attached to a Dewalt Angle Grinder. The biocompatible metal samples were then subject to either Solution 1, water with …

An Inverted Teaching Model For A Mechanics Of Materials Course, Jeffery S. Thomas, Timothy A. Philpot

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Instructors at Missouri University of Science and Technology have been offering certain sections of a mechanics of materials course in an inverted format for the past two years. In this format, students learn the concepts outside of class, using a textbook, animations and videos developed by the authors, and work on homework either individually or in groups during the optional class time. Students take eight multiple-choice exams and a final exam that is common to both the inverted sections and the more traditional lecture-based sections. Homework in the inverted sections is assigned but not graded. The in-class exams are given …

Effects Of Ovariectomy, Seasonal Changes, And Anatomical Position On The Compact Bone Remodeling As Seen In The Adult Ovine Model, Erica Wong

Master's Theses

The purpose of this study is to characterize the compact bone remodeling of the ovariectomized ewe and its effectiveness as an animal model for studies of postmenopausal osteoporosis. The use of animal models is a beneficial way to evaluate the effectiveness of medical devices and therapeutic agents for treating diseases. The ovine model is an attractive option because of its large size and similar bone remodeling to humans. However, this species, like most animals, does not undergo a natural menopause, making an ovariectomy necessary for studies of estrogen depletion. The OVX (ovariectomized) sheep has been widely accepted as a model …

Application Of A Heuristic Method To A Water Distribution System For Determining Optimal Water Quality Monitoring Locations, Lawrence David Johnson

Master's Theses

Although regulations and requirements for water quality source monitoring have increased, drinking water distribution systems can still be considered vulnerable to purposeful or accidental contamination.

This study analyzes the transport of the hypothetical contaminant Cryptosporidium through the distribution system of a city with a population of 30,000 to 50,000 in an attempt to locate the optimal monitoring locations in the distribution system. Cryptosporidium was selected due to its resistance to chlorine and it’s conservative properties for vulnerability assessments. The method for selecting the optimal monitoring locations was taken from Chastain (2004) which developed and examined the method for a virtual …

Hapss, Hybrid Aircraft Propulsion System Synthesis, Michael W. Green

Master's Theses

Hybrid Aircraft Propulsion System Synthesis (HAPSS) is a computer program that sizes and analyzes pure-series hybrid electric propulsion systems for aircraft. The development of this program began during a NASA SBIR contract, in conjunction with Empirical Systems Aerospace (ESAero), with the creation of a propulsion fan design tool. Since the completion of this contract in July 2010, the HAPSS program has been expanded to combine the many aspects of a hybrid propulsion system such as the propulsive fans, electric motors, generators, and controllers, and the internal combustion engines.

This thesis describes the benefits and drawbacks of aircraft hybrid propulsion systems …

Preparation And Characterization Of Electrospun Poly(D, L-Lactide-Co-Glycolide) Scaffolds For Vascular Tissue Engineering And The Advancement Of An In Vitro Blood Brain Barrier Model, Deven Chandrakant Patel

Master's Theses

Developing an in vitro Blood Brain Barrier model that will replicate the physiological, anatomical, and functional characteristics of the native BBB has gained significant attention. Such a model would enable prediction of the penetration of CNS targeting drug candidates across the BBB, allow pre-screening and optimization strategies to be developed for new drugs and gene delivery formulations, and permit research groups to further understand how a dysfunctional BBB is involved in the pathogenesis of several neurological diseases.

The Tissue Engineering laboratory at the California Polytechnic State University, San Luis Obispo is currently in the process of developing a dynamic in …

Global Technology Initiative At San Jose State University: Results Of Seven Years Of An International Experience For Students, Belle Wei, Patricia Backer, Wenchiang Chung, Andrew Wood

Faculty Publications

For XXX students to thrive in the highly competitive global economy, it is critical to develop international perspectives and knowledge. The $1 million Global Technology Initiative (GTI), established in 2004, provides SJSU students with an opportunity to gain a global perspective of the world by learning about technology and business developments in the Asia Pacific region. GTI donors are high-tech business leaders with strong business ties in Silicon Valley and the Asia Pacific region. Given the current trend of engineering globalization in the global economy, particularly the trend of outsourcing Silicon Valley manufacturing, development, and design work to foreign countries, …

Hydraulically Driven Mechanical Representation Of A Biological System, Andrea Argouarch, Michael Mceachern, Brandon Parham

Biomedical Engineering

No abstract provided.

Development Of A Blood Flow Measurement Protocol Using Particle Image Velocimetry, Jennifer Chi-Ying Go

Biomedical Engineering

Peripheral Arterial Occlusive Disease (PAOD) is an acquired inflammatory disease where a peripheral artery becomes occluded due to the buildup of atherosclerotic plaques. In patients that possess collateral arteries, an occlusion can lead to shear induced outward remodeling, arteriogenesis, of these collaterals, partially restoring blood flow. However, newly remodeled collaterals exhibit reduced functional vasodilation, which may impair normal activity, such as ambulation. To model chronic ischemia and arteriogenesis in collaterals, a femoral artery ligation in a murine hindlimb is commonly performed. Previous efforts by our group involved measurements of collateral artery diameter to assess the impact of arteriogenesis on functional …

Development And Characterization Of Plga And Eptfe Blood Vessel Mimics Using Gene Expression Analysis, Michael Gibbons, Sarah Ur

Biomedical Engineering

Tissue engineered blood vessels (TEBV’s) have the potential to act not only as a replacement for diseased vessels, but also as a testing platform for intravascular devices such as stents. To this end, the goal of this study was to develop protocols for the construction of TEBV’s composed of human vascular cells and either expanded polytetrafluoroethylene (ePTFE) or poly-lactic-co-glycolic acid (PLGA), as well as a protocol for gene expression in those TEBV’s. Initial experiments involved only human umbilical vein endothelial cells (HUVEC’s), but after low cell confluency and spreading in single-sodded vessels a second cell type, human umbilical vein smooth …

Co-Removal Of Atrazine And Nitrate From Groundwater Using A Mulch Biofilm, Allison L. Cole

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The popular broadleaf herbicide atrazine is often found in contaminated groundwater along with other agricultural chemicals, such as nitrate. Mulch biowalls, a passive treatment placed in situ, can inexpensively remediate groundwater by intercepting and treating a contaminant plume. Three types of organic mulch: cedar, cypress, and hardwood were evaluated for their ability to act as supporting materials for a biowall to simultaneously remove atrazine and nitrate from groundwater. Physical and chemical properties of the mulch were characterized. Cedar mulch had the highest organic carbon content, 996 mg/g. The adsorptive capacity of the mulch for atrazine and nitrate, in mono …

Driver Behavior Classification And Lateral Control For Automobile Safety Systems, Jing Yang

Dissertations

Advanced driver assistance systems (ADAS) have been developed to help drivers maintain stability, improve road safety, and avoid potential collision. The data acquisition equipment that can be used to measure the state and parameter information of the vehicle may not be available for a standard passenger car due to economical and technical limitations. This work focuses on developing three technologies (longitudinal tire force estimation, driver behavior classification and lateral control) using low-cost sensors that can be utilized in ADAS.

For the longitudinal tire force estimation, a low cost 1Hz positioning global system (GPS) and a steering angle sensor are used …

Virtual Reality Visual Feedback And Its Effect On Brain Excitability, Soha Saleh

Dissertations

This dissertation examines manipulation of visual feedback in virtual reality (VR) to increase excitability of distinct neural networks in the sensorimotor cortex. The objective is to explore neural responses to visual feedback of motor activities performed in complex virtual environments during functional magnetic resonance imaging (fMRI), and to identify sensory manipulations that could further optimize VR rehabilitation of persons with hemiparesis. In addition, the effects of VR therapy on brain reorganization are investigated. An MRI-compatible VR system is used to provide subjects with online visual feedback of their hand movement. First, the author develops a protocol to analyze variability in …

Image Statistical Frameworks For Digital Image Forensics, Patchara Sutthiwan

Dissertations

The advances of digital cameras, scanners, printers, image editing tools, smartphones, tablet personal computers as well as high-speed networks have made a digital image a conventional medium for visual information. Creation, duplication, distribution, or tampering of such a medium can be easily done, which calls for the necessity to be able to trace back the authenticity or history of the medium. Digital image forensics is an emerging research area that aims to resolve the imposed problem and has grown in popularity over the past decade. On the other hand, anti-forensics has emerged over the past few years as a relatively …